The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

A compatibilized composite of recycled polypropylene filled with cellulosic fiber from recycled corrugated paper board: Mechanical properties,morphology, and thermal behavior

This article deals with the feasibility of using recycled corrugated paper board (rPF) as the reinforcing material for recycled plastics. The composites of recycled polypropylene (rPP) and rPF were prepared by extrusion compounding and injection molding, and the rPP/rPF composites compatibilized by maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted ethylene‐1‐octene copolymer (POE‐g‐MA), and maleic anhydride grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA) were also prepared. The crystallization and melting behavior, mechanical properties, thermal stability, and morphology of these composites were studied. The results indicated that rPF promoted the crystallization, enhanced the strength and toughness of rPP/rPF composites to some extent while decreased thermal stability at the same time. PP‐g‐MA and POE‐g‐MA improved the dispersion and interface adhesion of rPF, and further upgraded the mechanical properties and vicat softening temperatures. Among these compatibilizers, PP‐g‐MA was most favorable to the strength improvement while POE‐g‐MA was most favorable to the toughness improvement. As for SEBS‐g‐MA, it had no obvious modification effect. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nonisothermal crystallization kinetics of polypropylene‐layered double hydroxide composites: Correlation with morphology

In this work the effect of nanofiller on nonisothermal crystallization behavior of composites based on polypropylene (PP) was investigated by differential scanning calorimetry. The materials were prepared by melt mixing. Both an alkyl sulfonate salt modified layered double hydroxide (LDH) and an unmodified LDH were used as nanofillers and both PP and PP/polypropylene grafted with maleic anhydride (PP‐g‐MA) blend were used as matrices. The morphology of composites was investigated by X‐ray diffraction and transmission electron microscopy. No exfoliation was noticed in all prepared composites, but the hybrid materials showed an intercalated structure. The thermal properties and crystallization behavior were studied by conventional differential scanning calorimetry. In particular, the kinetic crystallization parameters were obtained using the modified Avrami equation for a nonisothermal process, whereas the activation energy of the global crystallization process was estimated using the Kissinger equation. The Avrami parameters suggest a significant effect on the crystallization of PP for the composites containing both the organically modified LDH and PP‐g‐MA. The results indicate a complex crystallization process of PP and evidence that the crystallization process can not be only explained by intercalation phenomenon, but the constrain effect ofpolymer chains on the filler surface and/or betweenthe filler clusters should play a significant role. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Morphology,Thermal Stability,and Mechanical Behavior of [Poly(propylene)‐grafted Maleic Anhydride]‐Layered Expanded Graphite Oxide Composites

PP‐g‐MA‐layered EGO composites were prepared directly by solution blending. Two types of PP‐g‐MA/EGO composites were prepared using different mixing methods: distributive and dispersive. In this study, the effects of the mixing method of EGO on the crystalline structure and thermo‐mechanical properties of PP‐g‐MA/EGO composites are reported. WAXD exhibited a shift in 2θ of the monoclinic (α) phase of PP‐g‐MA and (002) EGO peaks for PP‐g‐MA/EGO layered composites, which indicated a modification of the crystalline structure of PP‐g‐MA in the layered composites. DSC exhibited a single characteristic melting peak of monoclinic (α) crystalline phase PP‐g‐MA. The incorporation of EGO increased T_c indicating that the EGO acted as a nucleating agent for PP‐g‐MA. The crystallinity of the PP‐g‐MA/EGO composites was found to be dependent on the mixing method. Thermogravimetry demonstrated that PP‐g‐MA in the presence of EGO has higher degradation temperature, suggesting that the graphite particles acted as a thermal barrier material for PP‐g‐MA. DMA indicated that incorporation of EGO into PP‐g‐MA increased the storage modulus, due to the hydrogen bonding between EGO and MA of PP‐g‐MA.

     

Polypropylene/clay nanocomposites: An innovative one‐pot process

This work discloses a novel one‐pot preparation method of polypropylene (PP)/clay nanocomposites with high degree of clay delamination and improved thermal, mechanical and rheological properties. The in situ simultaneous synthesis of carboxylate clay from native clay and ionomer of PP‐graft maleic anhydride (PP‐g‐MA) through trihydrate sodium acetate addition, combined with water injection in the extrusion process, appears to be a valuable alternative to the use of organoclay for producing PP/PP‐g‐MA/clay nanocomposites. The influence of PP‐g‐MA graft content, and of its ionomer form, onto the clay dispersion has been especially investigated. PP‐g‐MA of low graft content is compared to a home‐made highly grafted PP‐g‐MA synthesized in the presence of N‐bromosuccinimide (NBS). The nanocomposites prepared by combining the use of NBS‐mediated PP‐g‐MA, trihydrate sodium acetate and water injection exhibit the highest clay dispersion. Thermal, rheological, and mechanical properties of the nanocomposites have been measured. POLYM. COMPOS., 36:644–650, 2015. © 2014 Society of Plastics Engineers     

Effects of carbon nanofibers on the fracture,mechanical, and thermal properties of PP/SEBS‐g‐MA blends

Polypropylene/maleated (styrene‐ethylene‐butadiene‐styrene) (PP/SEBS‐g‐MA) blends reinforced with 0.2–2.5 wt% carbon nanofibers (CNFs) were prepared by injection molding. The structure, thermal, mechanical, and fracture behaviors of PP/SEBS‐g‐MA blends and their nanocomposites were studied. Wide‐angle X‐ray diffraction (WAXD) results showed that the SEBS‐g‐MA and/or CNF additions do not induce a structural change of PP. Tensile measurements showed that the Young's modulus and tensile yield strength increase with the increasing filler content. Izod impact and essential work of fracture test results demonstrated that CNFs are beneficial to improve the impact strength and specific essential work of fracture of PP/SEBS‐g‐MA blends. Therefore, tough PP‐nanocomposites can be achieved by melt‐blending low fractions of CNFs and appropriate elastomer contents. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Melt‐mixed polypropylene/acrylonitrile‐butadiene‐styrene blends with multiwall carbon nanotubes: Effect of compatibilizer and modifier on morphology and electrical conductivity

Cocontinuous blends of 45/55 polypropylene (PP)/acrylonitrile‐butadiene‐styrene (ABS) with multiwall carbon nanotubes (MWNT) were prepared by melt‐mixing in a conical twin‐screw microcompounder. PP‐grafted‐maleic anhydride (PP‐g‐MA) and styrene MA were used as compatibilizers for PP/ABS blends. Scanning electron microscopic observations showed phase segregation of PP‐g‐MA in the blends. State of dispersion of MWNT in the presence or absence of the compatibilizers was assessed through AC electrical conductivity measurements and crystallization studies of the blends. An improvement in AC electrical conductivity was observed in blends in presence of either styrene MA or dual compatibilizers. The lowest electrical percolation threshold was achieved at 0.1 wt % of MWNT using sodium salt of 6‐amino hexanoic acid‐modified MWNT. Significant increase in crystallization temperature of PP phase of blends with MWNT was observed in the presence of compatibilizers as compared to blends without compatibilizers. An attempt has been made to address the complex issues of phase segregation, compatibilization, and dispersion of MWNT in cocontinuous blends of PP/ABS. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of clay type and of clay–masterbatch product in the preparation of polypropylene/clay nanocomposites

Clay containing polypropylene (PP) nanocomposites were prepared by direct melt mixing in a twin screw extruder using different types of organo‐modified montmorillonite (Cloisite 15 and Cloisite 20) and two masterbatch products, one based on pre‐exfoliated clays (Nanofil SE 3000) and another one based on clay–polyolefin resin (Nanomax‐PP). Maleic anhydride‐grafted polypropylene (PP‐g‐MA) was used as a coupling agent to improve the dispersability of organo‐modified clays. The effect of clay type and clay–masterbatch product on the clay exfoliation and nanocomposite properties was investigated. The effect of PP‐g‐MA concentration was also considered. Composite morphologies were characterized by X‐ray diffraction (XRD), field emission gun scanning electron microscopy (FEG‐SEM), and transmission electron microscopy (TEM). The degree of dispersion of organo‐modified clay increased with the PP‐g‐MA content. The thermal and mechanical properties were not affected by organo‐modified clay type, although the masterbatch products did have a significant influence on thermal and mechanical properties of nanocomposites. Intercalation/exfoliation was not achieved in the Nanofil SE 3000 composite. This masterbatch product has intercalants, whose initial decomposition temperature is lower than the processing temperature (T ～ 180°C), indicating that their stability decreased during the process. The Nanomax‐PP composite showed higher thermal and flexural properties than pure PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

PET/PP blending by using PP‐g‐MA synthesized by solid phase

In attempts to improve the compatibility of polypropylene (PP) with polyethylene terephthalate (PET), a maleic anhydride grafted PP (PP‐g‐MA) was evaluated as a compatibilizer in a blend of 30/70 wt % PP/PET. PP‐g‐MA was produced from isotactic homopolymer PP utilizing the technique of solid phase graft copolymerization. Qualitative confirmations of the grafting were made by Fourier transform infrared spectroscopy (FTIR). Three different weight percent of compatibilizer, PP‐g‐MA, i.e., 5, 10, and 15 wt % have been used in PP/PET blends. The compatibilizing efficiency for PP/PET blend was examined using differential scanning calorimetry (DSC), optical microscopy (OM), scanning electron microscopy (SEM) of crycrofractured surfaces, and energy dispersive X‐ray spectrum (EDAX). The results show that the grafted PP promotes a fine dispersed phase morphology, improves processability, and modifies the crystallization behavior of the polyester component. These effects are attributed to enhance phase interaction resulting in reduced interfacial tension. Also, the results show that the compatibilizing effects of the three amounts of grafted PP in blend are different and dependent on the amount used. Adding 10 wt % of compatibilizer into blend produced the finest dispersed morphology. Elemental analysis results show that PP is matrix. DSC determination revealed that the melting temperature (T_m) of the PET component declined to some extent by comparison with neat PET. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3986–3993, 2007     

Melt rheological properties of polypropylene–maleated polypropylene blends. I. Steady flow by capillary

Melt rheological properties of blends of polypropylene (PP) and PP grafted with maleic anhydride (PP‐g‐MA) are studied using a capillary rheometer. A pseudoplastic flow behavior is observed. The pseudoplasticity of the melt reduces with an increase of PP‐g‐MA content and/or temperature. The PP‐g‐MA component in the blend acts as decreasing melt viscosity, especially in the lower shear rate region, while the addition of PP‐g‐MA to PP does not cause obvious increase of die swell ratio. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1641–1648, 1999     

Preparation and performance characteristics of short‐glass‐fiber/maleated styrene–ethylene–butylene–styrene/polypropylene hybrid composites

Eighty/twenty polypropylene (PP)/styrene–ethylene–butylene–styrene (SEBS) and 80/20 PP/maleated styrene–ethylene–butylene–styrene (SEBS‐g‐MA) blends reinforced with 30 wt % short glass fibers (SGFs) were prepared by extrusion and subsequent injection molding. The influence of the maleic anhydride (MA) functional group grafted to SEBS on the properties of SGF/SEBS/PP hybrid composites was studied. Tensile and impact tests showed that the SEBS‐g‐MA copolymer improved the yield strength and impact toughness of the hybrid composites. Extensive plastic deformation occurred at the matrix interface layer next to the fibers of the SGF/SEBS‐g‐MA/PP composites during impact testing. This was attributed to the MA functional group, which enhanced the adhesion between SEBS and SGF. Differential scanning calorimetry measurements indicated that SEBS promoted the crystallization of PP spherulites by acting as active nucleation sites. However, the MA functional group grafted to SEBS retarded the crystallization of PP. Finally, polarized optical microscopy observations confirmed the absence of transcrystallinity at the glass‐fiber surfaces of both SGF/SEBS/PP and SGF/SEBS‐g‐MA/PP hybrid composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1303–1311, 2002     

Compatibilization of polypropylene/ poly(3‐hydroxybutyrate) blends

Blending polypropylene (PP) with biodegradable poly(3‐hydroxybutyrate) (PHB) can be a nice alternative to minimize the disposal problem of PP and the intrinsic brittleness that restricts PHB applications. However, to achieve acceptable engineering properties, the blend needs to be compatibilized because of the immiscibility between PP and PHB. In this work, PP/PHB blends were prepared with different types of copolymers as possible compatibilizers: poly(propylene‐g‐maleic anhydride) (PP–MAH), poly (ethylene‐co‐methyl acrylate) [P(E–MA)], poly(ethylene‐co‐glycidyl methacrylate) [P(E–GMA)], and poly(ethylene‐co‐methyl acrylate‐co‐glycidyl methacrylate) [P(E–MA–GMA)]. The effect of each copolymer on the morphology and mechanical properties of the blends was investigated. The results show that the compatibilizers efficiency decreased in this order: P(E–MA–GMA) > P(E–MA) > P(E–GMA) > PP–MAH; we explained this by taking into consideration the affinity degree of the compatibilizers with the PP matrix, the compatibilizers properties, and their ability to provide physical and/or reactive compatibilization with PHB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis of a new compatibilisant agent PVC‐g‐MA and its use in the PVC/alfa composites

The main objective of this research was to synthesize a new compatibilisant agent (PVC‐g‐MA), which was grafted from the maleic anhydride on the PVC chains. The presence of maleic anhydride grafting on PVC was made evident by infrared analysis. PVC‐g‐MA was used like compatibilisant to solve the problem of the incompatibility between the hydrophobic polymeric matrix (PVC) and hydrophilic fiber (alfa). Composites samples were prepared with different alfa fiber loading (10, 20, and 30 wt %) and incorporating PVC‐g‐MA (1, 3, and 5 wt %) or PP‐g‐MA (3 wt %). The tensile properties, the thermal stability and the morphology of the composites were investigated. The result indicated that the PVC‐g‐MA increased the interfacial adhesion between the fibers and the polymer matrix and this effect was better than that obtained for the maleated‐polypropylene‐coupled composites. Microstructure analysis of the fractured surfaces of MAPP modified composites confirmed improved interfacial bonding. The addition of alfa and PVC‐g‐MA increased the thermal stability of the composites. The temperature of degradation of the polymer matrix increased about 16°C in comparison to the noncoupled composite, indicating that PVC‐g‐MA improved the thermal stability of the polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Multiwalled carbon nanotubes‐based polypropylene composites: Influence of interfacial interaction on the crystallization behavior of polypropylene

Composites of polypropylene (PP) and multi‐walled carbon nanotubes (MWCNTs) were prepared via melt‐mixing utilizing Li‐salt of 6‐amino heaxanoic acid (Li‐AHA) modified MWCNTs in the presence of a compatibilizer (polypropylene‐g‐maleic anhydride; PP‐g‐MA). Improved interaction between the anhydride group of PP‐g‐MA and the amine functionality of Li‐AHA was confirmed via FTIR and Raman spectroscopic analysis. A higher glass transition temperature (T_g) of the PP phase has been observed in these composites as compared to pristine MWCNTs‐based composites. The crystallization temperature (T_c) of the PP phase was increased as a function of pristine MWCNTs concentration in PP/MWCNTs composites indicating hetero‐nucleating action of MWCNTs. However, T_c value was decreased in the presence of Li‐AHA modified MWCNTs indicating the adsorbed Li‐AHA on the MWCNTs surface. Moreover, T_c value was higher in the presence of Li‐AHA modified MWCNTs with PP‐g‐MA as compared to that of without PP‐g‐MA, suggesting the desorbed Li‐AHA from the MWCNTs surface due to melt‐interfacial reaction. Further, MWCNTs were extracted by hot vacuum filtration technique from PP/MWCNTs composites containing Li‐AHA and PP‐g‐MA. The isothermal crystallization kinetics showed a variation in crystallization behavior of the PP phase in the corresponding composites as compared to the “extracted MWCNTs.” POLYM. ENG. SCI., 57:183–196, 2017. © 2016 Society of Plastics Engineers     

Effect of compatibilizer on morphology,thermal, and rheological properties of polypropylene/functionalized multi‐walled carbon nanotubes composite

Multi‐walled carbon nanotubes (MWCNTs) filled polypropylene (PP) composites were prepared by a corotating intermeshing twin screw extruder. To improve the dispersion of MWCNTs, the surface of MWCNT was modified with 1,10‐diaminodecane, and maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizer. Micrographs of well dispersed functionalized MWCNTs (diamine‐MWCNT) were observed due to the reaction between MA‐g‐PP and diamine‐MWCNT in PP/MA‐g‐PP/diamine‐MWCNTs composites. The different behaviors in crystallization and melting temperatures of PP/MA‐g‐PP/diamine‐MWCNTs composite were observed compared to PP and PP/neat‐MWCNT. Especially, the decomposition temperature of the composite was increased by 50°C compared to PP. PP/MA‐g‐PP/diamine‐MWCNTs composite showed the highest complex viscosity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Nonisothermal crystallization kinetics of polypropylene/polypropylene‐g‐polystyrene/polystyrene blends

The nonisothermal crystallization kinetics of polypropylene (PP), PP/polystyrene (PS), and PP/PP‐g‐PS/PS blends were investigated with differential scanning calorimetry at different cooling rates. The Jeziorny modified Avrami equation, Ozawa method, and Mo method were used to describe the crystallization kinetics for all of the samples. The kinetics parameters, including the half‐time of crystallization, the peak crystallization temperature, the Avrami exponent, the kinetic crystallization rate constant, the crystallization activation energy, and the F(T) and a parameters were determined. All of the results clearly indicate that the PP‐g‐PS copolymer accelerated the crystallization rate of the PP component in the PP/PP‐g‐PS/PS blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011