Effect of Organomodified Ni-Al Layered Double Hydroxide (OLDH) on the Properties of Polypropylene (PP)/LDH Nanocomposites

This work addresses the effect of organomodified layer double hydroxide (OLDH) on the properties of PP/LDH nanocomposites prepared by melt intercalation method using a single screw extruder with maleic anhydride grafted polypropylene (PP-g-MA) as a compatibilizer. For this, Ni-Al LDH was first prepared by the co-precipitation method at constant pH using their nitrate salts. The above synthesized pristine LDH was organically modified using sodium dodecyl sulphate (SDS) by the regeneration method. The structural and thermal properties of LDH and PP nanocomposites were performed by X-ray diffraction (XRD), FTIR spectroscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The influence of LDH loading on the mechanical and thermal properties of the nanocomposite was also investigated. The XRD results confirmed the formation of exfoliated PP/LDH nanocomposites. PP/LDH nanocomposites exhibited enhanced thermal stability relative to the pure PP. When 10% weight loss was selected as a point of comparison, the decomposition temperature of PP/LDH (5 wt%) nanocomposite was 15.3°C higher than that of pure PP. The DSC result indicated an increase in crystallization and melting temperature of the PP/LDH nanocomposites compared to pure PP. Overall, the mechanical properties of the PP/LDH nanocomposites increased with an increase in the LDH content. The maximum improvement of tensile strength, Young's modulus, flexural strength, and flexural modulus for the PP/LDH nanocomposite was found to be 11, 22.5, 28, and 22%, respectively, over neat PP. For comparison purposes, a nanocomposite with 5 wt% modified bentonite (PP/B5) was also prepared under the same operating condition and there was no significant improvement in mechanical properties (tensile strength and modulus).     

Influence of incorporation sequence of silica nanoparticles on morphology,crystallization behavior,mechanical properties,and thermal resistance of melt blended thermoplastic natural rubber

Thermoplastic natural rubber nanocomposites based on epoxidized natural rubber (ENR) and polypropylene blends at a fixed blend ratio of 50/50 wt% reinforced with small amount (2.5 wt%) of nanosilica (SiO₂) were prepared by melt‐mixing through three different incorporation sequences in an internal mixer. The effects of incorporation techniques on morphology, crystallization behavior, mechanical properties, dynamic, rheological characteristics, and thermal resistance of thermoplastic natural rubber (TPNR) nanocomposites were investigated. It was found that the dispersion of nanosilica in TPNRs was significantly dependent on the incorporation sequence. In the case where SiO₂ was premixed in ENR before blending with polypropylene (PP), the final morphology showed the good dispersion of SiO₂ in ENR phase, while the SiO₂ particles were localized near the PP interface when SiO₂ was premixed the in PP first. Whereas, when the three components were simultaneously mixed, the SiO₂ particles were mainly dispersed in the PP phase. It was also found that the improvements of Young's modulus, tensile strength, damping behavior, and thermal stability of TPNR nanocomposites were more pronounced when the SiO₂ particles localized in ENR phase. By contrast, the presence of SiO₂ particles in PP domain either near the interface or inside the PP phase affected the reduction in crystallinity of PP phase and showed a negative effect on mechanical properties due to the poor interface interaction between PP and SiO₂ particles. POLYM. COMPOS., 33:1911–1920, 2012. © 2012 Society of Plastics Engineers     

Mechanical,thermal, and rheological behavior of ethylene methyl acrylate‐MWNT nanocomposites

Mechanical, thermal, and rheological properties of ethylene methyl acrylate (EMA) composites reinforced with multiwalled carbon nanotubes (MWNTs) have been reported here. Morphological analyses revealed that MWNTs are more uniformly dispersed in EMA upto 3.5 wt% MWNTs loading. Uniform dispersion of MWNTs in EMA matrix leads to decreased crystallinity and increased crystallite size. These are reflected in the mechanical and thermal properties of the composites. The storage moduli of the composites significantly increase by the incorporation of MWNTs, particularly at higher temperatures. The nanocomposites register a slightly higher viscosity than that of neat EMA depending on the contents of MWNTs. Storage modulus (in dynamic shear) increases especially at higher frequency levels due to increased polymer–filler interactions. Dynamic and steady shear rheological properties register a good correlation in regard to the viscous versus elastic response of the nanocomposites. The morphology correlates well with the dynamic rheological characteristics of these nanocomposites. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Influence of reactive compatibilization on the structure and properties of PP/LDH nanocomposites

Polypropylene (PP)/layered double hydroxide (LDH) nanocomposites were prepared by the direct melt intercalation method using maleic anhydride grafted polypropylene (PP‐g‐MAH) as a reactive compatibilizer. The compatibilization effects provided by PP‐g‐MAH in different weight fractions and their influence on the structure and properties of the final nanocomposites were investigated. The interactions and structural morphology of the nanocomposites were examined by Fourier transform infrared spectroscopy, X‐ray diffraction and transmission electron microscopy. Thermal, mechanical and rheological properties of these nanocomposites were investigated as a function of compatibilizer concentration. The detailed morphological and X‐ray diffraction results revealed that the degree of LDH dispersion increases as the amount of PP‐g‐MAH increases. Study of the linear viscoelastic properties showed that the storage modulus G′ is very sensitive to the microstructure of the nanocomposite. The thermal properties of the nanocomposites were significantly influenced by the weight fraction of PP‐g‐MAH due to the shielding and nucleating effect of exfoliated layers. Both the tensile strength and modulus showed substantial improvements with increasing PP‐g‐MAH content, while the elongation at break substantially decreased, although the presence of PP‐g‐MAH somewhat improves these values. The overall results showed that 10 wt% of compatibilizer is optimum to achieve nanocomposites with better performance. Copyright © 2011 Society of Chemical Industry     

Thermomechanical properties of virgin and recycled polypropylene impact copolymer/CaCO3 nanocomposites

The effect of successive injection moldings on the thermal, rheological, and mechanical properties of a polypropylene impact copolymer (PP) was investigated. The crystal content decreased as the molecular weight decreased due to chain scission with repeated injection molding. The Young modulus and the yield stress remained constant, despite a drop in the strain to break. Virgin and recycled PP matrix were filled with nanosized calcium carbonate (CaCO₃) particles. The effect of morphology on the thermal and mechanical properties of nanocomposites of virgin and recycled PP filled with nanosized CaCO₃ particles was also studied. The mechanical properties of the nanocomposites were strongly influenced by the intrinsic toughness of the matrix and the concentration and dispersion of the filler. The yield strength and strain of virgin PP decreased gradually, while its Young's modulus increased slightly with increasing CaCO₃ loading. These phenomena were less pronounced for the recycled matrix. Incorporation of nanoparticles to virgin matrix produced an increase in tensile stiffness and ductility, when good dispersion of the filler was achieved. However, the impact strength dropped dramatically for high filler contents. A significant increase in impact strength was observed for the recycled PP. POLYM. ENG. SCI., 50:1904–1913, 2010. © 2010 Society of Plastics Engineers     

Mechanical,thermal, and rheological properties of graphene‐based polypropylene nanocomposites prepared by melt mixing

In this article, we describe the fabrication by melt mixing of graphene‐polypropylene nanocomposites and present the effect of graphene addition on some selected properties of polypropylene (PP). The graphene nanosheets (GNs) used as nano‐reinforcing agents were obtained through chemical reduction of graphene oxide by hydrazine hydrate. GNs were characterized and successfully dispersed into PP matrix to produce PP/GNs nanocomposites. The effects of GNs content on thermal, mechanical, and rheological properties were reported, and the obtained results were discussed in terms of morphology and state of dispersion and distribution of the GNs within the polymer matrix. Characterization by scanning electron microscopy and X‐ray diffraction of the nanocomposites has shown a relatively good dispersion of GNs in the polymer matrix, with the presence of only few aggregates. Increasing GNs content resulted in a significant increase in both mechanical and thermal properties with only few percent of GNs loading. Rheological behavior of the PP/GNs nanocomposites showed a Maxwellian‐like behavior for low GNs concentrations and a viscoelastic solid‐like behavior for GNs content exceeding the concentration of the percolation threshold. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Synthesis and properties of polypropylene/layered double hydroxide nanocomposites with different LDHs particle sizes

In order to investigate whether the particle sizes of inorganic additives in polymer have an influence on the flame‐retardant and other properties of the polymer, five types of Mg₃Al–CO₃ layered double hydroxide (LDHs) with particle diameters of 80–100, 200–350, 500–550, 550–600, and 700–900 nm were synthesized using a hydrothermal method. The obtained Mg₃Al–CO₃ LDHs were treated using the aqueous miscible organic solvent treatment method to give highly dispersed platelets in Polypropylene (PP). The thermal stability, flame retardancy, and mechanical properties of the PP/AMO–LDH nanocomposites were investigated systematically. The results showed that the thermal stability and flame retardancy of PP could be improved after incorporating AMO–LDHs. The temperature at 50% weight loss (T_0.5) of PP/LDH (700–900 nm) nanocomposites with a LDH loading of 15 wt % was increased by 57 °C. When the LDHs loading was 40 wt %, the peak heat release rate (PHRR) of the PP/LDH nanocomposites with small LDHs particle sizes (<350 nm) was decreased by ca. 58%. The limiting oxygen index was increased by 5% for PP/LDH (80–100 nm) nanocomposites. The response surface regression results also indicated that both LDH particle size and loading have influence on PHRR, heat release capacity, tensile strength, and elongation at break. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46204.     

Synthesis of exfoliated PP/LDH nanocomposites via melt‐intercalation: Structure,thermal properties,and photo‐oxidative behavior in comparison with PP/MMT nanocomposites

Exfoliated polypropylene (PP)/layered double hydroxide (LDH) nanocomposites have been successfully synthesized via melt‐intercalation. Their structure, thermal properties, and photo‐oxidative behavior have been characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), dynamic mechanical thermal analysis (DMA), X‐ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectrum. TGA and DMA data show that the PP/LDH nanocomposites have enhanced thermal stability compared with virgin PP and corresponding PP/montmorillonites (MMT) nanocomposites, especially in high temperature range during the thermal decomposition of the samples. XPS and FTIR results give positive evidence that the photo‐oxidation mechanism of PP in the PP/LDH materials is not modified compared with that of virgin PP. However, photo‐oxidation rate of PP/LDH materials is much lower than that of PP and PP/MMT samples, indicating that the PP/LDH nanocomposites have better UV‐stability. POLYM. ENG. SCI. 46:1153–1159, 2006. © 2006 Society of Plastics Engineers     

The rheological,thermostable, and mechanical properties of polypropylene/fullerene C60 nanocomposites with improved interfacial interaction

Polypropylene (PP)/C₆₀ nanocomposites with improved interfacial interaction were prepared via in situ melt radical reaction. It was found that the relaxation time of PP/C₆₀ nanocomposites containing peroxide increased due to the reaction between C₆₀ and PP macroradicals and the formation of long chain branched or crosslinking structure. Thermogravimetric analysis (TGA) results showed that the thermal stability of PP/C₆₀ nanocomposites was enhanced. The initial decomposition temperatures and activation energy of PP/C₆₀ nancomposites were strongly influenced by the content of unreacted C₆₀. Because of the improved interfacial interaction, PP/C₆₀ nanocomposites containing peroxide showed obvious increase in tensile strength, Young' modulus, flexural strength, flexural modulus, and impact strength, compared to PP/C₆₀ nanocomposites (without peroxide) containing the same content of C₆₀. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Effect of organoclay on the properties of maleic‐anhydride grafted polypropylene and poly(methyl methacrylate) blend

Poly(methyl methacrylate)/polypropylene (PMMA/PP) and PMMA/maleic‐anhydride grafted PP (MAPP) blends and their blend nanocomposites containing 2 wt% organoclay (Cloisite 15A, denoted C15A), prepared by a melt mixer were studied. Both X‐ray diffraction (XRD) and transmission electron microscopy (TEM) revealed exfoliated polymer blend nanocomposites. Scanning electron microscopy (SEM) studies indicated a droplet dispersion morphology for all the blends while addition of C15A into PMMA/MAPP blend resulted to a co‐continuous morphology. In fact, rheological data and thermal properties indicated that the PMMA/MAPP/C15A nanocomposite showed a better homogeneous dispersion of silicate layers than PMMA/PP/C15A nanocomposite. A Cole–Cole plot and relaxation modulus indicated a solid‐like character for PMMA/MAPP and PMMA/MAPP/C15A, while a liquid‐like behavior was noticed for PMMA/PP and PMMA/PP/C15A. The effect of an organoclay on the dynamic mechanical properties of samples was investigated using dynamic mechanical analysis (DMA) which showed a significant enhancement on the storage modulus of the PMMA/MAPP/C15A as compared to PMMA/PP/C15A . POLYM. COMPOS., 38:431–440, 2017. © 2015 Society of Plastics Engineers     

Improvement in properties of multiwalled carbon nanotube/polypropylene nanocomposites through homogeneous dispersion with the aid of surfactants

The effects of different surfactants on the properties of multiwalled carbon nanotubes/polypropylene (MWCNT/PP) nanocomposites prepared by a melt mixing method have been investigated. Sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (NaDDBS) were used as a means of noncovalent functionalization of MWCNTs to help them to be dispersed uniformly into the PP matrix. The effects of these surfactant‐treated MWCNTs on morphological, rheological, thermal, crystalline, mechanical, and electrical properties of MWCNT/PP composites were studied using field emission scanning electron microscopy, optical microscopy, rheometry, tensile, and electrical conductivity tests. It was found that the surfactant‐treatment and micromixing resulted in a great improvement in the state of dispersion of MWCNTs in the polymer matrix, leading to a significant enhancement of Young's modulus and tensile strength of the composites. For example, with the addition of only 2 wt % of SDS‐treated and NaDDBS‐treated MWCNTs, the Young's modulus of PP increased by 61.1 and 86.1%, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphology, rheology and dynamic mechanical properties of PP/EVA/clay nanocomposites

This paper reports on morphology, rheology and dynamic mechanical properties of polypropylene (PP)/ethylene vinyl acetate (EVA) copolymer/clay nanocomposite system prepared via a single step melt compounding process using a twin screw micro-compounder. Scanning electron microscopic (SEM) investigations revealed that the dispersed phase droplet size was reduced with incorporation of an organo-modified montmorillonite (OMMT). This reduction was more significant in presence of a maleated PP (PP-g-MAH) used as compatibilizer. Phase inversion in the compatibilized blends caused a further decrease in PP droplet size. The OMMT gallery spacing was higher in nanocomposites with EVA as matrix which could be attributed to higher tendency of OMMT nanoparticles towards EVA rather than PP. This enhanced tendency was confirmed by rheological analysis too. Transmission electron microscopy (TEM) results also showed that the majority of OMMT nanoparticles were localized on the interface and within EVA droplets. According to dynamic mechanical analysis, the compatibilized nanocomposites showed higher storage and loss moduli due to better dispersion of OMMT layers. The modulus enhancement of nanocomposites as a function of OMMT volume fraction was modeled by Halpin-Tsai’s-Nielsen expression of modulus for nanocomposites. The results of modeling suggested that the aspect ratio of the intercalated OMMT, in the form of Einstein coefficient (K _E), plays a determining role in the modulus enhancement of nanocomposites.     

Effect of polymer matrix/montmorillonite compatibility on morphology and melt rheology of polypropylene nanocomposites

In this study, Ca²⁺‐montmorillonite (Ca²⁺‐MMT) and organo‐montmorillonite (OMMT) were modified by three compatibilizers with different degrees of polarity [poly(ethylene glycol) (PEG), alkyl‐PEG, and polypropylene (PP)‐g‐PEG]. PP/MMT nanocomposites were prepared by melt blending and characterized using X‐ray diffraction and transmission electron microscopy. The results showed the degree of dispersion of OMMT in the PP/PP‐g‐PEG/OMMT (PMOM) nanocomposite was considerably higher than those in the PP/PEG/OMMT and PP/alkyl‐PEG/OMMT nanocomposites, which indicated that the dispersion was relative to the compatibility between modified OMMT and PP matrix. Linear viscoelasticity of PP/MMT nanocomposites in melt states was investigated by small amplitude dynamic rheology measurements. With the addition of the modified MMT, the shear viscosities and storage modulus of all the PP/MMT nanocomposites decreased. It can be attributed to the plasticization effect of PEG segments in the three modifiers. This rheological behavior was different from most surfactant modified MMT nanocomposites which typically showed an increase in dynamic modulus and viscosity relative to the polymer matrix. The unusual rheological observations were explained in terms of the compatibility between the polymer matrix and MMT. In addition, the mechanical properties of PP/MMT nanocomposites were improved. A simultaneous increase in the tensile strength and toughness was observed in PP/PMOM nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rheological,thermal, and mechanical characterization of fly ash‐thermoplastic composites with different coupling agents

Composite materials were prepared by mixing fly ash obtained from biomass combustion as filler and isotactic polypropylene (PP) as matrix. Three silane‐type coupling agents mainly differing in the size of their functional groups were used to improve the compatibility between both components. Uniaxial tensile tests showed that the incorporation of untreated ash into PP led to stiffer but also more brittle and weaker materials, as Young's modulus significantly increased and tensile strength and elongation at break decreased. Furthermore, an enhancement in storage and loss moduli as well as in composite viscosity was observed with the addition of fly ash. Hardness tests and thermal and fracture surface analyzes revealed tensile test results similar to those mentioned earlier. In summary, after analyzing the effects of the three silanes on mechanical, thermal, morphological, and rheological properties, the silane containing the vinyl functional group (XL10) was selected as the most appropriate for the PP/ash composites investigated. POLYM. COMPOS., 31:1722–1730, 2010. © 2010 Society of Plastics Engineers.     

Polypropylene–nanosilica‐filled composites: Effects of epoxy‐resin‐grafted nanosilica on the structural,thermal, and dynamic mechanical properties

This article reports a comparative study of polypropylene (PP) nanocomposites synthesized with nanosilica (NS) and diglycidyl ether of bisphenol A, an epoxy‐resin‐grafted nanosilica (ENS), as nanofillers. These nanocomposites were prepared with the melt‐mixing method at a constant loading level of 2.5 wt %; this loading level was much lower than that used for fillers in conventional composites. The effects of pure NS and ENS on the thermal, structural, mechanical, and dynamic mechanical properties of PP were analyzed with wide‐angle X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, and scanning electron microscopy. The transmission electron microscopy studies showed a better dispersion of ENS in the PP matrix, that is, in the polypropylene‐epoxy‐resin‐grafted nanosilica (PP–ENS) nanocomposite, in comparison with NS in the PP matrix, that is, in the polypropylene–nanosilica (PP–NS) nanocomposite. Also, the thermogravimetric analysis results showed a higher thermal stability for PP–ENS than PP–NS. Furthermore, the dynamic mechanical analysis studies showed an increase in the elastic modulus and glass‐transition temperature for PP–ENS with respect to PP–NS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2117–2124, 2006     

Self-sacrificial templating synthesis of flower-like nickel phyllosilicates and its application as high-performance reinforcements in epoxy nanocomposites

The nanocomposites of flower-like nickel phyllosilicate particles incorporated into epoxy resin were fabricated via an in-situ mixing process. The flower-like nickel phyllosilicate particles were firstly synthesized using a mild self-sacrificial templating method, and the morphology and lamellar structure were examined carefully. Several properties of mechanical, thermal and tribological responses of epoxy nanocomposites were performed. It was demonstrated that adequate flower-like nickel phyllosilicate particles dispersed well in the matrix, and the nanocomposites displayed enhanced tensile strength and elastic modulus but decreased elongation at break as expected. In addition, friction coefficient and wear rate were increased first and then decreased along with the particle content, and showed the lowest values at a mass fraction of 5%. Nevertheless, the incorporated flower-like nickel phyllosilicate particles resulted in the continuously increasing thermal stability of epoxy resin (EP) nanocomposites. This study revealed the giant potential of flower-like particles in preparing high-quality EP nanocomposites.     

Crystallization,mechanical, and fracture behavior of mullite fiber‐reinforced polypropylene nanocomposites

This study describes the reinforcement effect of surface modified mullite fibers on the crystallization, thermal stability, and mechanical properties of polypropylene (PP). The nanocomposites were developed using polypropylene‐grafted‐maleic anhydride (PP‐g‐MA) as compatibilizer with different weight ratios (0.5, 1.0, 1.5, 2.5, 5.0, and 10.0 wt %) of amine functionalized mullite fibers (AMUF) via solution blending method. Chemical grafting of AMUF with PP‐g‐MA resulted in enhanced filler dispersion in the polymer as well as effective filler‐polymer interactions. The dispersion of nanofiller in the polymer matrix was identified using scanning electron microscopy (SEM) elemental mapping and transmission electron microscopy (TEM) analysis. AMUF increased the Young's modulus of PP in the nanocomposites up to a 5 wt % filler content, however, at 10 wt % loading, a decrease in the modulus resulted due to agglomeration of AMUF. The impact strength of PP increased simultaneously with the modulus as a function of AMUF content (up to 5 wt %). The mechanical properties of PP‐AMUF nanocomposites exhibited improved thermal performance as compared to pure PP matrix, thus, confirming the overall potential of the generated composites for a variety of structural applications. The mechanical properties of 5 wt % of AMUF filled PP nanocomposite were also compared with PP nanocomposites generated with unmodified MUF and the results confirmed superior mechanical properties on incorporation of modified filler. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43725.     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.     

PP–elastomer–filler hybrids. I. Processing,microstructure, and mechanical properties

Three-component systems with a polypropylene (PP) matrix consisting of polar elastomer (ethylene–propylene rubber and styrene–ethylene–butylene–styrene grafted with maleic anhydride) or of polar PP (PP grafted with maleic anhydride) and filler were investigated. Three microstructures of PP–elastomer–filler hybrids were obtained by processing control and elastomer or PP modification with the maleic anhydride: fillers and rubber particles were separated in the PP matrix, rubber particles with filler core were distributed in the PP matrix, and mixed microstructures of the first and second. A study of mechanical properties showed that the elastic modulus increased in the first microstructure and impact strength increased in the second microstructure. Mechanisms for the relationships between microstructure, processing, and mechanical properties are discussed. © 1996 John Wiley & Sons, Inc.