Synergistic effect of ammonium polyphosphate and expandable graphite on flame‐retardant properties of acrylonitrile‐butadiene‐styrene

A new intumescent flame‐retardant (IFR) system consisting of expandable graphite (EG) and ammonium polyphosphate (APP) was applied in acrylonitrile–butadiene–styrene (ABS) resin. A synergistic effect between EG and APP on the flame retardancy of ABS was observed. Fixing the total loading of flame retardant at 15 wt %, the limited oxygen index (LOI) could reach 31 vol % at a weight ratio of 3 : 1 for EG and APP. While LOI values of EG‐ and APP‐filled ABS were only 26.0 and 21.5 vol % at the same loading, respectively. The UL‐94 vertical burning test suggested that samples with different ratios of EG and APP could all pass V‐0 rating while the samples containing EG and APP alone only passed V‐1 rating. Thermogravimetric analysis indicated that the addition of EG and APP (3 : 1 by weight) to ABS led to an increase in the amount of high‐temperature residue by 11.8 wt %, and a decrease of mass loss rate by 0.7%/°C compared with pure ABS. Scanning electronic microscopy revealed a homogeneous compact intumescent char layer of ABS/EG/APP samples. Based on our experiment and combined with others' previous studies, the synergistic mechanism is inferred. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/clay nanocomposites

Bis(3‐triethoxysilylpropyl) tetrasulfane (TSS) was reacted with the silanol groups of the commercially available clay, Closite®25A (C25A) to prepare TSS‐C25A, which was melt‐compounded with acrylonitrile‐butadiene‐styrene copolymer (ABS). The tetra sulfide groups of TSS‐C25A may chemically react with the vinyl groups of ABS to enhance the interaction between the clay and ABS. The ABS/clay composites exhibited much higher tensile strength and elongation at break than the neat ABS. Especially the elongation at break of ABS/TSS‐C25A composite was 5 times higher than that of neat ABS. The X‐ray diffraction patterns of the clay showed that the d₀₀₁ basal spacing was enlarged from 1.89 nm to 2.71–2.86 nm as a result of the compounding with ABS. According to the thermogravimetric analysis, the thermal decomposition of the composite took place at a slightly higher temperature than that of neat ABS. Intercalated/exfoliated coexisting structures were observed by transmission electron microscopy for the ABS/clay composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Application of a novel halogen‐free intumescent flame retardant for acrylonitrile‐butadiene‐styrene

A novel intumescent flame retardant (IFR), containing ammonium polyphosphate (APP) and poly(tetramethylene terephthalamide) (PA4T), was prepared to flame‐retard acrylonitrile‐butadiene‐styrene (ABS). The flame retardation of the IFR/ABS composite was characterized by limiting oxygen index (LOI) and UL‐94 test. Thermogravimetric analysis (TGA) and TGA coupled with Fourier transform infrared spectroscopy (TG‐FTIR) were carried out to study the thermal degradation behavior of the composite and look for the mechanism of the flame‐retarded action. The morphology of the char obtained after combustion of the composite was studied by scanning electron microscopy (SEM). It has been found the intumescent flame retardant showed good flame retardancy, with the LOI value of the PA4T/APP/ABS (7.5/22.5/70) system increasing from 18.5 to 30% and passing UL‐94 V‐1 rating. Meanwhile, the TGA and TG‐FTIR work indicated that PA4T could be effective as a carbonization agent and there was some reaction between PA4T and APP, leading to some crosslinked and high temperature stable material formed, which probably effectively promoted the flame retardancy of ABS. Moreover, it was revealed that uniform and compact intumescent char layer was formed after combustion of the intumescent flame‐retarded ABS composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synergistic effect of THEIC‐Based charring agent on flame retardant properties of polylactide

A novel charring agent tris(2‐hydrooxyethyl) isocyanurate terephthalic acid ester, tetramer (TT4) was synthesized using tris(2‐hydrooxyethyl) isocyanurate and terephthalic acid as raw materials, and it was characterized by Fourier transformed infrared spectrometry and ¹H‐NMR spectrum. It was combined with ammonium polyphosphate (APP) to form intumescent flame retardants for polylactide (PLA). The combustion properties and thermal stability of PLA/APP/TT4 composites were evaluated by UL‐94 burning tests, limiting oxygen index (LOI), and thermogravimetric analyses (TGA). It was found PLA with 30 wt % of APP/TT4 (5 : 1) achieved UL‐94 V‐0 rating and a 40.6 LOI value. Results from TGA demonstrated that APP/TT4 composites could retard the degradation of PLA above 410°C. The char residue at 500°C is higher than 24%, showing a good char forming ability. Moreover, the continuous and expansionary char layer observed from the SEM images proved good charring forming ability of TT4. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41218.     

Synergistic effect of melamine polyphosphate with macromolecular charring agent novolac in wollastonite filled PA66

In this article, macromolecular charring agent linear novolac (NA) was served as a synergist with nitrogen‐phosphorous flame retardant melamine polyphosphate (MPP) for the flame‐resistance of wollastonite (WT) filled polyamide 66 (PA66). The investigations showed that MPP/NA system possessed obvious synergistic effects by increasing the charring rate and amount, therefore, showing much higher flame retardancy than the filled PA66 flame retarded with MPP alone. The corresponding char layer structure of MPP/WT/PA66 and MPP/NA/WT/PA66 was investigated and their difference was analyzed. In addition, as a multifunctional additive, NA could act as a compatibilizer and lubricant in the system, and endowed the material with improved mechanical performance and processability. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Application of styrene‐acrylonitrile random copolymer–polyarylate block copolymer as reactive compatibilizer for polyamide and acrylonitrile‐butadiene‐styrene blends

Styrene‐acrylonitrile random copolymer (SAN) and polyarylate (PAr) block copolymer were applied as a reactive compatibilizer for polyamide‐6 (PA‐6)/acrylonitrile‐butadiene‐styrene (ABS) copolymer blends. The SAN–PAr block copolymer was found to be effective for compatibilization of PA‐6/ABS blends. With the addition of 3.0–5.0 wt % SAN–PAr block copolymer, the ABS‐rich phase could be reduced to a smaller size than 1.0 μm in the 70/30 and 50/50 PA‐6/ABS blends, although it was several microns in the uncompatibilized blends. As a result, for the blends compatibilized with 3–5 wt % block copolymer the impact energy absorption reached the super toughness region in the 70/30 and 50/50 PA‐6/ABS compositions. The compatibilization mechanism of PA‐6/ABS by the SAN–PAr block copolymer was investigated by tetrahydrofuran extraction of the SAN–PAr block copolymer/PA‐6 blends and the model reactions between the block copolymer and low molecular weight compounds. The results of these experiments indicated that the SAN–PAr block copolymer reacted with the PA‐6 during the melt mixing process via an in situ transreaction between the ester units in the PAr chain and the terminal amine in the PA‐6. As a result, SAN–PAr/PA‐6 block copolymers were generated during the melt mixing process. The SAN–PAr block copolymer was supposed to compatibilize the PA‐6 and ABS blend by anchoring the PAr/PA‐6 and SAN chains to the PA‐6 and ABS phases, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2300–2313, 2002     

Fire performance and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/modified expandable graphite composites

The fire performance and mechanical properties of an acrylonitrile‐butadiene‐styrene (ABS) copolymer compounded with different expandable graphites (EG) and fire retardants were studied by using the limiting oxygen index test, the UL‐94 test, a mechanical test, and a thermogravimetric analysis. The ground EG treated with phosphoric acid and silane could have the great increase of the volume expansion ratio. The addition of the treated EG in ABS significantly enhances the fire performance but decreases the impact strength of ABS. ABS with the treated EG has a much higher impact strength than with the as‐received EG because of the smaller particle size of the treated EG and the better adhesion between the ABS and the treated EG. The addition of modified ammonium polyphosphate or decabromodiphenyl oxide/antimony trioxide can considerably improve the fire performance of ABS/treated EG composites because of a synergistic effect. The V‐0 grade (UL‐94) ABS composite with the limiting oxygen index of 32.5 can be obtained by adding small amounts of the treated EG and modified ammonium polyphosphate into ABS. Thermogravimetric analysis results indicate that the initial vapor release temperatures and the weight loss rates of ABS/EG composites are closely related to their fire performance and affected by the fire retardant used. Copyright © 2011 John Wiley & Sons, Ltd.     

Properties of polycarbonate/acrylonitrile‐butadiene‐styrene/talc composites

The morphology, tensile, impact properties, and thermal expansion behavior of polycarbonate (PC)/acrylonitrile‐styrene‐butadiene (ABS)/talc composites with different compositions and mixing sequences were investigated. From the studies of morphology of the PC/ABS/talc composites, it was observed that some talc particles were located in both the PC and the ABS phases of the blend but most were at the interface between the PC and ABS phases for every mixing sequence. Aspect ratios of the talc particles determined by TEM image analysis reasonably matched values computed from tensile modulus using composite theory. The thermal expansion behavior, or CTE values, was not significantly influenced by the mixing sequence. The impact strength of the PC/ABS/talc composites depended significantly on the mixing sequence; a premix with PC gave the poorest toughness. The molecular weight of the PC in PC/talc composites was found to be significantly decreased. It appears that the impact strength of the PC/ABS/talc composites is seriously compromised by the degradation of the PC caused by talc. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis of novel triazine charring agent and its effect in intumescent flame‐retardant polypropylene

A novel charring agent (CNCA‐DA) containing triazine and benzene ring, using cyanuric chloride, aniline, and ethylenediamine as raw materials, was synthesized and characterized. The effects of CNCA‐DA on flame retardancy, thermal degradation, and flammability properties of polypropylene (PP) were investigated by limited oxygen index (LOI), vertical burning test (UL‐94), thermogravimetric analysis (TGA), and cone calorimeter test (CCT). The TGA results showed that CNCA‐DA had a good char forming ability, and a high initial temperature of thermal degradation; the char residue of CNCA‐DA reached 18.5% at 800°C; Ammonium polyphosphate (APP) could improve the char residue of APP/CNCA‐DA system, the char residue reached 31.6% at 800°C. The results from LOI and UL‐94 showed that the intumescent flame retardant (IFR) containing CNCA‐DA and APP was very effective in flame retardancy of PP. When the mass ratio of APP and CNCA‐DA was 2 : 1, and the IFR loading was 30%, the IFR showed the best effect; the LOI value reached 35.6%. It was also found that when the IFR loading was only 20%, the flame retardancy of PP/IFR can still pass V‐0 rating in UL‐94 tests, and its LOI value reached 27.1%. The CCT results demonstrated that IFR could clearly change the decomposition behavior of PP and form a char layer on the surface of the composites, consequently resulting in efficient reduction of the flammability parameters, such as heat release rate (HRR), total heat release (THR), smoke production rate (SPR), total smoke production (TSP), and mass loss (ML). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and properties of nano‐CaCO3/acrylonitrile‐butadiene‐styrene composites

CaCO₃/acrylonitrile‐butadiene‐styrene (ABS) and CaCO₃/ethylene‐vinyl acetate copolymer (EVA)/ABS nanocomposites were prepared by melting‐blend with a single‐screw extruder. Mechanical properties of the nanocomposites and the dispersion state of CaCO₃ particles in ABS matrix were investigated. The results showed that in CaCO₃/EVA/ABS nanocomposites, CaCO₃ nanoparticles could increase flexural modulus of the composites and maintain or increase their impact strength for a certain nano‐CaCO₃ loading range. The tensile strength of the nanocomposites, however, was appreciably decreased by adding CaCO₃ nanoparticles. The microstructure of neat ABS, CaCO₃/ABS nanocomposites, and CaCO₃/EVA/ABS nanocomposites was observed by scanning electron microscopy. It can be found that CaCO₃ nanoparticles were well‐dispersed in ABS matrix at nanoscale. The morphology of the fracture surfaces of the nanocomposites revealed that when CaCO₃/EVA/ABS nanocomposites were exposed to external force, nano‐CaCO₃ particles initiated and terminated crazing (silver streak), which can absorb more impact energy than neat ABS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006     

Mechanical and UV‐shielding properties of in situ synthesized poly(acrylonitrile‐butadiene‐styrene)/zinc oxide nanocomposites

A series of poly(acrylonitrile‐butadiene‐styrene)/ZnO nanocomposites with different ZnO nanoparticles content were synthesized by a mass‐suspension polymerization process. Nanocomposites obtained through this technique presented high impact resistance despite the presence of agglomerates for high ZnO nanoparticles content so that, these samples were subjected to twin‐screw extrusion. The extrusion led to a dramatic morphological change and increased in impact resistance, higher than 100% in most of the cases. On the other hand, the higher the ZnO content, the higher the UV blocking (>95% for 1 and 3% of ZnO) for both materials, before and after extrusion. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

Synergistic effect between silicone‐containing macromolecular charring agent and ammonium polyphosphate in flame retardant polypropylene

A novel silicone‐containing macromolecular charring agent (Si‐MCA) was synthesized via polycondensation, and it was combined with ammonium polyphosphate (APP) to flame retard polypropylene (PP). The results showed that Si‐MCA exhibited a good synergistic effect with APP in flame retardant PP. When the content of APP was 18.7 wt % and Si‐MCA was 6.3 wt %, the limiting oxygen index value of the PP/APP/Si‐MCA composite was 33.5%, and the vertical burning (UL 94) test classed a V‐0 rating. The peak heat release rate, total heat release, average mass loss rate, and total smoke production of the composite were also decreased significantly. Moreover, the PP/APP/Si‐MCA composite showed an outstanding water resistance. After soaking in 70°C water for 168 h, the PP/APP/Si‐MCA composite could still reach a UL 94 V‐0 rating at 20.0 wt % IFR loading, whereas the PP/APP/PER composite failed to pass the UL 94 test even at 25.0 wt % IFR loading. Thermogravimetric analysis, thermogravimetry‐Fourier transform infrared spectrometry, and scanning electron microscopy‐energy dispersive X‐ray spectrometry results revealed that a compact and thermostable intumescent char was formed by APP/Si‐MCA during burning, thus effectively improved the flame retardancy of PP. The possible synergistic mechanism between APP and Si‐MCA was also discussed. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41580.     

Thermal degradation behaviors and flame retardancy of PC/ABS with novel silicon‐containing flame retardant

A novel flame retardant (DVN) containing silicon, phosphorus, and nitrogen has been synthesized from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO), vinylmethyldimethoxy silane (VMDMS) and N‐β‐(aminoethyl)‐γ‐aminopropyle methyl dimethoxy silane (NMDMS), then incorporated into polycarbonate/acrylonitrile butadiene styrene (PC/ABS) alloy. The flame retardancy of PC/ABS/DVN is evaluated by cone calorimeter and limited oxygen index (LOI) and the thermal degradation behavior is investigated by thermogravimetric analysis under nitrogen and air. The PC/ABS/DVN sample was thermally degraded at 400°C for different amounts of time and studied by Fourier transform infrared spectroscopy to better understand the mechanism of flame retardancy. The results show that the thermal stability and flame retardancy of PC/ABS are improved by incorporation of DVN. Scanning electric microscopy results show that the outer surface of the char layer of PC/ABS/DVN after the LOI test is smooth and the internal structure is like swollen cells, which benefits the flame retardancy of PC/ABS. Copyright © 2007 John Wiley & Sons, Ltd.     

Magnetite‐functionalized graphene/poly(styrene‐butadiene‐styrene) composites: thermal and mechanical properties

Advanced polymer composites containing organic–inorganic fillers are gaining increasing attention due to their multifunctional applications. In this work, poly(styrene‐butadiene‐styrene) (SBS) composites containing magnetite‐functionalized graphene (FG) were prepared by a dissolution ? dispersion ? precipitation solution method. Evidently, through morphology studies, amounts of FG were well distributed in the SBS matrix. Improvements in neat SBS properties with respect to FG loading in terms of thermal stability, creep recovery and mechanical properties are presented. As expected, the addition of FG improved the thermal stability and mechanical properties of the composites. The yield strength and Young's modulus of the SBS increased by 66% and 146% at 5 wt% filler loading which can be attributed to the reinforcing nature of FG. Similarly, an increase in the storage and loss modulus of the composites showed a reinforcement effect of the filler even at low concentration. The results also showed the significant role of FG in improving the creep and recovery performance of the SBS copolymer. Creep deformation decreased with filler loading but increased with temperature. © 2017 Society of Chemical Industry     

Poly(acrylonitrile‐butadiene‐styrene)/Poly(ether ether ketone) Blends: an Attempt Towards a Polymer Reinforced Polymer Composite

Summary: Blends of poly(acrylonitrile‐butadiene‐styrene) (ABS) and poly(ether ether ketone) (PEEK), in which PEEK has been used as a reinforcing medium for the ABS matrix in ratios up to 20 wt.‐% of the blend, were prepared by melt mixing using a laboratory mixer. All the blend compositions were processed at the ABS processing temperature so that the PEEK was dispersed in the ABS matrix without actually melting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) studies revealed that the glass transition temperature (T_g) of the ABS phase in the blend did not show any appreciable change with composition. The dynamic storage modulus measured by DMA was found to be higher for the blend as compared to pure ABS due to reinforcement of the matrix by PEEK. The tensile strength and modulus behavior of these blends were found to follow the curves predicted using models proposed for composite systems having perfect adhesion, which shows the presence of some physical interaction between the blend components. The good tensile properties of the blend have been correlated with the observed morphology. The disperse phase in the blend has been found to be present in extremely small (sub‐micron) dimensions, which not only provides more surface area for possible interactions between the blend components but also result in efficient stress transfer between the matrix and the dispersed phase during the tensile tests. The thermal stability of the blends was investigated using thermogravimetric analysis (TGA). TGA further revealed that the constituents degraded at their respective decomposition temperatures.

SEM micrograph of tensile fractured surface of an ABS/PEEK 90/10 blend.     

Optimizing 3D printing performance of acrylonitrile‐butadiene‐styrene composites with cellulose nanocrystals/silica nanohybrids

The preparation of 3D printed products with excellent comprehensive performance is still receiving much attention. Cellulose, the most abundant and green natural polymer, was used in this study to fabricate polymeric composites used for 3D printing. Specifically, novel cellulose nanocrystals/silica nanohybrids (CSNs) were synthesized via the sol–gel method using cellulose nanocrystals (CNCs) obtained by hydrolysis of sulfuric acid as raw materials, and the thermostability was significantly improved due to the adsorption of silica (SiO₂) on the surface of the CNCs via hydrogen bonding and covalent bonds. Subsequently, the CSNs were used in fused deposition modeling (FDM) with acrylonitrile‐butadiene‐styrene (ABS) as the matrix. Unlike ABS/CNC product which shows obvious yellowing, the ABS/CSN product shows a smooth undefiled surface, demonstrating their excellent applicability to high temperature FDM molding. Further, the effect of different silane coupling agents on the mechanical properties was compared and organically modified CSNs (oCSNs) were prepared using KH570 to optimize the dispersion of the filler and the interaction with the matrix. Satisfactorily, the addition of organically modified oCSNs not only does not degrade the fluidity but it also eliminates the warpage of FDM products and improves both layer adhesion and mechanical properties. This study provides a pioneering strategy for the thermal processing applications of CNCs and the modification of FDM products. © 2019 Society of Chemical Industry     

A conductive foam: Based on novel poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer filled by carbon black

In this article, a conductive foam based on a novel styrene‐based thermoplastic elastomer called poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer S(BS)S was prepared and introduced. S(BS)S was particularly designed for chemical foaming with uniform fine cells, which overcame the shortcomings of traditional poly(styrene‐b‐butadiene‐b‐styrene) tri‐block copolymer (SBS). The preparation of conductive foams filled by the carbon black was studied. After the detail investigation of cross‐linking and foaming behaviors using moving die rheometer, the optimal foaming temperature was determined at 180°C with a complex accelerator for foaming agent. Scanning electron microscopy (SEM) images shown that the cell bubbles of conductive foam were around 30–50 µm. The conductivity of foams was tested using a megger and a semiconductor performance tester. SEM images also indicated that the conductivity of foams was mainly affected by the distribution of carbon black in the cell walls. The formation of the network of the carbon black aggregates had a contribution to perfect conductive paths. It also found that the conductivity of foams declined obviously with the foaming agent content increasing. The more foaming agent led to a sharp increasing of the number of cells (from 2.93 × 10⁶ to 6.20 × 10⁷ cells/cm³) and a rapid thinning of the cell walls (from 45.3 to 1.4 µm), resulting in an effective conductive path of the carbon black no forming. The conductive soft foams with the density of 0.48–0.09 g/cm³ and the volume resistivity of 3.1 × 10³?2.5 × 10⁵ Ω cm can be easily prepared in this study. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41644.