Synthesis and characterization of self‐doped poly(aniline‐co‐aminonaphthalene sulfonic acid) nanotubes

Self‐doped poly(aniline‐co‐aminonaphthalene sulfonic acid) (PANI‐ANSA) was synthesized by the copolymerization of 5‐aminonaphthalene‐2‐sulfonic acid (ANSA) and aniline. Scanning electron microscopy and transmission electron microscopy showed that the morphology of PANI‐ANSA synthesized at a high molar ratio of aniline to ANSA was nanotubular, but at a low molar ratio, only a granular morphology formed. A possible formation mechanism for nanotubes was proposed. PANI‐ANSA had better thermal stability than HCl‐doped polyaniline; the highest onset decomposition temperature was as high as 340°C because of ? SO₃H linked with the polymer backbone by a covalent bond. PANI‐ANSA was partially soluble in basic solutions, and its conductivity was between 10^?2 and 10^?4 S/cm, depending on the sulfonation degree. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1297–1301, 2003     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Characterizations and Cr (VI) adsorption properties of polyaniline/filter‐paper composite

Polyaniline/filter‐paper (PANI/FP) composite was prepared by in situ polymerization of polyaniline onto FP and subsequently evaluated for the removal of Cr (VI) from aqueous solution. Scanning electron microscopy and Fourier‐transform infrared were used to investigate the morphology and physicochemical property of PANI/FP composite. Batch experimental results showed that pH value and temperature could affect the removal capability of PANI/FP composite. Langmuir and Freundlich models were used to analysis the equilibrium adsorption, and both of the two models showed the similar correlation coefficients (about R² = 0.9383). Although the removal capability was still limited, the PANI/FP composite showed the great potential that can be used as an effective adsorbent for removing Cr (VI) from industrial waste‐water. POLYM. COMPOS., 35:993–998, 2014. © 2013 Society of Plastics Engineers     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Electrically conductive polyaniline/polyimide microfiber membrane prepared via a combination of solution blowing and subsequent in situ polymerization growth

Dodecylbenzene sulfonic acid (DBSA) doped-polyaniline (PANI) coated conductive polyimide (PI) microfiber membrane was prepared by chemical oxidation polymerization. PI nanofiber membrane was prepared by solution blowing. Fourier transform infrared spectra (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) proved that the successful preparation of composite microfiber membrane with core-shell structures. At the same time, the PANI had an effect of protection on PI nanofiber, which was detected by thermal gravimetric analysis (TGA). The orthogonal experiments were designed to determine the optimal reaction conditions for the conductivity of PANI/PI microfiber membranes as following: ANI concentration (0.15 mol L^?1), APS concentration (0.1 mol L^?1) and DBSA concentration (0.3 mol L^?1). The conductivity of PANI/PI microfiber membranes could arrive to 3.83 × 10^?2 S cm^?1. Moreover, the PANI/PI microfiber membranes had a superior hexavalent chromium (Cr (VI)) adsorption performance. The factors affecting the performance of hexavalent chromium (Cr (VI)) removal from the aqueous solutions were investigated.     

Synthesis,characterization, and comparison of self‐doped,doped, and undoped forms of polyaniline,poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)]

Polyaniline (PANI), poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)] were synthesized by chemical oxidative polymerization with ammonium persulfate as an oxidizing reagent in an HCl medium. The viscosities, electrical conductivity, and crystallinity of the resulting polymers (self‐doped forms) were compared with those of the doped and undoped forms. The self‐doped, doped, and undoped forms of these polymers were characterized with infrared spectroscopy, ultraviolet–visible spectroscopy, and a four‐point‐probe conductivity method. X‐ray diffraction characterization revealed the crystalline nature of the polymers. The observed decrease in the conductivity of the copolymer and poly(o‐anisidine) with respect to PANI was attributed to the incorporation of the methoxy moieties into the PANI chain. The homopolymers attained conductivity in the range of 3.97 × 10^?3 to 7.8 S/cm after doping with HCl. The conductivity of the undoped forms of the poly[aniline‐co‐(o‐anisidine)] and poly(o‐anisidine) was observed to be lower than 10^?5 J/S cm^?1. The conductivity of the studied polymer forms decreased by the doping process in the following order: self‐doped → doped → undoped. The conductivity of the studied polymers decreased by the monomer species in the following order: PANI → poly[aniline‐co‐(o‐anisidine)] → poly(o‐anisidine). All the polymer samples were largely amorphous, but with the attachment of the pendant groups of anisidine to the polymer system, the crystallinity region increased. The undoped form of poly[aniline‐co‐(o‐anisidine)] had good solubility in common organic solvents, whereas doped poly[aniline‐co‐(o‐anisidine)] was moderately crystalline and exhibited higher conductivity than the anisidine homopolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Blue fluorescent conductive poly(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene) homopolymer and its highly soluble copolymers with styrene or 9‐vinylcarbazole

A new blue fluorescent monomer, 9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene, was designed and synthesized in good yield. Its homopolymer poly(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene) (P(ADN)) and soluble conductive vinyl copolymers poly[(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene)‐co‐styrene] (P(ADN‐co‐S)) and poly[(9,10‐di(1‐naphthalenyl)‐2‐vinylanthracene)‐co‐(9‐vinylcarbazole)] (P(ADN‐co‐VK)) were synthesized using free radical solution polymerization. All the polymers showed high glass transition mid‐point temperatures (203 to 237 °C) and good thermal stabilities. The photoluminescence emission of the copolymers was similar to that of P(ADN) (with two maxima at 423 and 442 nm). The lifetimes of P(ADN‐co‐S) (6.82 to 7.91 ns) were all slightly less than that of P(ADN) (8.40 ns). The lifetime of P(ADN‐co‐VK) increased from 7.8 to 8.8 ns with an increase in VK content. The fluorescence quantum yields of P(ADN‐co‐S) showed an overall increasing tendency from 0.42 to 0.58. The quantum efficiencies of P(ADN‐co‐VK) decreased from 0.36 to 0.19 with an increase of VK fraction. With increasing S/VK content, the highest occupied molecular orbital of P(ADN‐co‐S)/P(ADN‐co‐VK) ranged from ?5.58 to ?5.73 eV, which was similar to that of P(ADN) (?5.71 eV). The band gaps of P(ADN‐co‐S) and P(ADN‐co‐VK) were about 2.97 eV, which were equal to that of P(ADN), and smaller than that of 2‐methyl‐9,10‐di(1‐naphthalenyl)anthracene (MADN) (3.04 eV) and poly(9‐vinylcarbazole) (3.54 eV). Preliminary electroluminescence results were obtained for a homojunction device with the configuration ITO/MoO₃ (20 nm)/P(ADN)/LiF (1 nm)/Al (100 nm), which achieved only 30–50 cd m^?2, due to P(ADN) having a low mobility of 4.7 × 10^?8 cm² V^?1 s^?1 compared to that of its model compound MADN of 6.5 × 10^?4 cm² V^?1 s^?1. © 2013 Society of Chemical Industry     

Photo‐induced protonation and conductivity of polyaniline/poly(ethylene glycol) and polyaniline/[poly(ethylene glycol)‐grafted polyaniline] composites

Composites of polyaniline in its emeraldine base form (PANI‐EB) and photo‐acid generators (PAG) show an increase in conductivity upon photo‐irradiation due to the protonation of PANI‐EB. Such materials may be utilized to fabricate conducting patterns by photo‐irradiation. However, the conductivity obtained by direct irradiation of PANI‐EB/PAG composites was normally quite low (<10^?3 S/cm) due to aggregation of highly loaded PAG. In this work, poly(ethylene glycol) (PEG), which is a proton transfer polymer, was added to PANI‐EB/PAG. Results showed that addition of low M_w (550) PEG significantly enhance the photo‐induced conductivity. Conductivities as high as 10^?1–10⁰ S/cm were observed after photo‐irradiation. This conductivity is comparable to that of PANI‐salt synthesized by oxidizing aniline in the presence of an acid. High M_w (8000) PEG is much less effective than PEG 550, which is attributed to its lower compatibility with PANI. PEG‐grafted PANI (N‐PEG‐PANI) was also studied as an additive. Composites of PANI‐EB and N‐PEG‐PANI showed conductivity as high as 10² S/cm after treatment with HCl vapor. The photo‐induced conductivity of the N‐PEG‐PANI/PANI‐EB/PAG composite reached 10^?2–10^?1 S/cm. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrochemical synthesis of poly(2‐iodoaniline) and poly(aniline‐co‐2‐iodoaniline) in acetonitrile

Poly(2‐iodoaniline) (PIANI) and poly(aniline‐co‐2‐iodoaniline) [P(An‐co‐2‐IAn)] were synthesized by electrochemical methods in acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The voltametry of the copolymer shows characteristics similar to those of conventional polyaniline (PANI), and it exhibits higher dry electrical conductivity than PIANI and lower than PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of the iodine moieties into the PANI chain. The structure and properties of these conducting films were characterized by FTIR and UV‐Vis spectroscopy and by an electrochemical method (cyclic voltametry). Conductivity values, FTIR and UV‐Vis spectra of the PIANI and copolymer were compared with those of PANI and the relative solubility of the PIANI and the copolymer powders was determined in various organic solvents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1652–1658, 2003     

Development of a conjugated polyaniline incorporated electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) composite membrane electrolyte for high performance dye‐sensitized solar cells

Different weight percentage (2, 3, 4, and 5 wt %) of polyaniline (PANI) were incorporated into electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐HFP) composite membranes (esCPMs). The regular morphology, molecular structure, crystallinity, porosity, electrolyte uptake, and leakage of the composite membranes were examined. The esCPMs were activated in liquid electrolyte containing 0.5 M LiI, 0.05 M I₂, and 0.5 M 4‐tert‐butylpyridine and 0.5 M 1‐butyl‐3‐methylimidazoliun iodide in acetonitrile to afford electrospun PVdF‐HFP/PANI composite membrane electrolytes (esCPMEs). The influence of different wt % of PANI on the esCPMEs was studied by electrochemical impedance measurements and Tafel polarization studies. The photovoltaic performance of a dye‐sensitized solar cell assembled using 3 wt % PANI incorporated esCPME exhibits a higher power conversion efficiency of 7.20% than that assembled using esPME (η = 6.42%). © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42777.     

Effect of different anchor groups on adsorption behavior and effectiveness of poly(N,N‐dimethylacrylamide‐co‐Ca 2‐acrylamido‐2‐methylpropanesulfonate) as cement fluid loss additive in presence of acetone–formaldehyde–sulfite dispersant

The impact of various anchor groups on adsorption behavior of AMPS® copolymers was studied. The anchor groups differ in anionic charge density. Copolymer adsorption and water retention of oil well cement slurries achieved from CaAMPS®‐co‐NNDMA in the presence of an acetone–formaldehyde–sulfite (AFS) dispersant were improved by incorporation of minor amounts (～ 1% by weight of polymer) of acrylic acid (CaAMPS®‐co‐NNDMA‐co‐AA), maleic acid anhydride (CaAMPS®‐co‐NNDMA‐co‐MAA), or vinyl phosphonic acid (CaAMPS®‐co‐NNDMA‐co‐VPA), respectively. Performance of these terpolymers was studied by measuring static filtration properties of oil well cement slurries at 27°C and 70 bar pressure. All fluid loss additives possess comparable molar masses and show the same adsorption behavior and effectiveness when no other admixture is present. In the presence of AFS dispersant, however, adsorption of CaAMPS®‐co‐NNDMA and hence fluid loss control is dramatically reduced, whereas effectiveness of CaAMPS®‐co‐NNDMA‐co‐AA is less influenced because of acrylic acid incorporated as additional anchor group. Even more, CaAMPS®‐co‐NNDMA‐co‐MAA combined with AFS allows simultaneous adsorption of both polymers and thus produces good fluid loss control. CaAMPS®‐co‐NNDMA‐co‐VPA no longer allows adsorption of AFS dispersant. This was also confirmed by rheological measurements. The results show that, in a binary admixture system, adsorption of the anionic polymer with anchor groups possessing higher charge density is preferred. Surface affinity of the anchor groups studied increase in the order ? SO → ? COO^? → vic‐(? COO^?)₂→ ? PO. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and properties of alkaline anion exchange membrane with semi‐interpenetrating polymer networks based on poly(vinylidene fluoride‐co‐hexafluoropropylene)

Alkaline anion exchange membrane with semi‐interpenetrating polymer network (s‐IPN) was constituted based upon quaternized poly(butyl acrylate‐co‐vinylbenzyl chloride) (QPBV) and poly(vinylidene fluoride‐co‐hexafluoropropylene) [P(VDF‐HFP)]. The QPBV was synthesized via the free radical copolymerization, followed by quaternization with N‐methylimidazole. The s‐IPN system was constituted by melting blend of QPBV and P(VDF‐HFP), and then crosslinking of P(VDF‐HFP). Ion exchange capacity, water uptake, mechanical performance, and thermal stability of these membranes were characterized. TEM showed that alkaline anion exchange membrane exhibited s‐IPN morphology with microphase separation. The fabricated s‐IPN membrane exhibited hydroxide ion conductivity up to 15 mS cm^?1 at 25 °C and a maximum DMFC power density of 46.55 mW cm^?2 at a load current density of 98 mA cm^?2 at 30 °C. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45775.     

Synthesis and characterization of N‐ and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]

Poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] was synthesized in an aqueous hydrochloric acid medium with a determined feed ratio by chemical oxidative polymerization. This polymer was used as a functional conducting polymer intermediate because of its side‐group reactivity. To synthesize the alkyl‐substituted copolymer, the initial copolymer was reacted with NaH to obtain the N‐ and O‐anionic copolymer after the reaction with octadecyl bromide to prepare the octadecyl‐substituted polymer. The microstructure of the obtained polymers was characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, and X‐ray diffraction. The thermal behavior of the polymers was investigated by thermogravimetric analysis and differential scanning calorimetry. The morphology of obtained copolymers was studied by scanning electron microscopy. The cyclic voltammetry investigation showed the electroactivity of poly [aniline‐co‐N‐(2‐hydroxyethyl) aniline] and N and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]. The conductivities of the polymers were 5 × 10^?5 S/cm for poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] and 5 ×10^?7 S/cm for the octadecyl‐substituted copolymer. The conductivity measurements were performed with a four‐point probe method. The solubility of the initial copolymer in common organic solvents such as N‐methyl‐2‐pyrrolidone and dimethylformamide was greater than polyaniline. The alkylated copolymer was mainly soluble in nonpolar solvents such as n‐hexane and cyclohexane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Novel hexamethylene diamine‐functionalized macroporous copolymer for chromium removal from aqueous solutions

Macroporous copolymers of poly[(glycidyl methacrylate)‐co ‐(ethylene glycol dimethacrylate)] (PGME ) with various crosslinker (ethylene glycol dimethacrylate) concentrations and porosity parameters and additionally functionalized with hexamethylene diamine (PGME‐HD ) were tested as potential Cr(VI ) oxyanion sorbents from aqueous solutions. Kinetics of Cr(VI ) sorption was investigated in the temperature range 298–343 K and the results were fitted to chemical reaction and particle diffusion models. The Cr(VI ) sorption obeys the pseudo‐second‐order model with definite influence of pore diffusion. A temperature rise promotes chromium removal, with a maximum experimental uptake capacity of 4.21 mmol g^?1 at 343 K for the sample with the highest amino group concentration. Equilibrium data were analysed with Langmuir, Freundlich and Temkin adsorption isotherm models. Thermodynamic parameters, i.e. Gibbs free energy (ΔG ⁰), enthalpy (ΔH ⁰) and entropy change (ΔS ⁰) and activation energy of sorption (E _a), were calculated. The Cr(VI) adsorption onto PGME‐HD was found to be spontaneous and endothermic, with increased randomness in the system. Desorption experiments show that chromium anion sorption was reversible and the PGME‐HD sample GMA 60 HD was easily regenerated with 0.1 mol L^?1 NaOH up to 90% recovery in the fourth sorption/desorption cycle. In the fifth cycle, a substantial sorption loss of 37% was observed. © 2016 Society of Chemical Industry     

Synthesis and characterization of conducting copolymer of Trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene with EDOT

Ferrocene‐substituted conducting polymer namely poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene‐co‐3,4‐ethylenedioxythiophene) [P(MTFE‐co‐EDOT)] was synthesized and its electrochromic properties were studied. Monomer, MTFE, was obtained using 2‐(ferrocenyl)ethene and 3‐methyl‐4‐bromothiophene. The structure of monomer was determined via Fourier transform infrared spectroscopy (FTIR), ¹H‐NMR, and ¹³C‐NMR techniques. The copolymer was synthesized using this monomer and EDOT. The resulting copolymer P(MTFE‐co‐EDOT) was characterized by cyclic voltammetry, FTIR, scanning electron microscopy, atomic force microscopy, and UV–vis spectroscopy. The conductivity measurements of copolymer and PEDOT were accomplished by the four‐probe technique. Although poly(trans‐1‐(4‐methyl‐3′‐thienyl)‐2‐(ferrocenyl)ethene) [P(MTFE)] reveals no electrochromic activity, its copolymer with EDOT has two different colors (violet and gray). Band gap (E_g) and λ_max of P(MTFE‐co‐EDOT) were determined. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of cyhalothrin‐loaded poly(2‐hydroxyethyl methacrylate)‐co‐polylactide (PHEMA‐co‐PLA) ultrafine particles

Poly(2‐hydroxyethyl methacrylate)‐co‐polylactide (PHEMA‐co‐PLA) and its corresponding cyhalothrin‐loaded ultrafine particles were successfully synthesized and prepared, respectively. The chemical structures of the copolymers have been confirmed by Fourier transform infrared spectroscopy (FTIR), ¹H‐nuclear magnetic resonance (¹H‐NMR), ¹³C‐nuclear magnetic resonance (¹³C‐NMR), and thermogravimetric analysis (TGA). Furthermore, the particle size, the cyhalothrin loading content (LC), and the cyhalothrin release behavior were investigated. PHEMA‐co‐PLA proved to be a good material for the preparation of ultrafine particles for lipophilic pesticide delivery. The developed cyhalothrin‐loaded PHEMA‐co‐PLA ultrafine particles showed good dispersity in water and sustained release behavior. In addition, it is easy to be prepared by both nanoprecipitation method and emulsion/solvent evaporation method. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of bi‐continuous poly(acrylonitrile‐co‐methyl acrylate) microporous membranes by a thermally induced phase separation method

Poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐MA)] flat microfiltration membranes were successfully prepared via the thermally induced phase separation (TIPS) method, by using low polar caprolactam (CPL) and methoxypolyethylene glycol 550 (MPEG 550) as the mixed diluent. In this work, P(AN‐MA) membranes exhibit bi‐continuous networks, porous surfaces, high porosity, and big pore size, when membrane fabricated from a high MPEG 550 content, low P(AN‐MA) concentration, and small cooling rate, it can be dry state preservation and do not need to be impregnated by any solvent. When the ternary system was composed of 15 wt % P(AN‐MA), 12.5 wt % CPL, and 87.5 wt % MPEG 550, formed at 25 °C air bath, membrane has the highest water flux of 4420 L m^?2 h^?1. The obtained P(AN‐AN) membrane displays a high carbonic black ink rejection ranging from 83.7 to 98.5 wt %. Moreover, P(AN‐MA) polymer not only retains the advantages of PAN but also reduces the polar component from 16.2 to 10.77 MPa^0.5. It can be used membrane matrix to obtain pore structure and excellent mechanical property membrane via TIPS. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46173.     

Synthesis and characterization of a porous poly(hydroxyethylmethacrylate‐co‐ethylene glycol dimethacrylate)‐based hydrogel device for the implantable delivery of insulin

Poly(hydroxyethylmethacrylate‐co‐ethylene glycol dimethacrylate) [poly(HEMA‐co‐EGDMA)]‐based hydrogel devices were synthesized by a free‐radical polymerization reaction with 2‐hydroxyethylmethacrylate as the monomer, different concentrations of ethylene glycol dimethacrylate (EGDMA) as the crosslinking agent, and ammonium persulfate/N,N,N′,N′‐tetra‐methyl ethylenediamine as the free‐radical initiator. The porosity of the poly(HEMA‐co‐EGDMA) hydrogels was controlled with water as the porogen. The Fourier transform infrared spectrum of poly(HEMA‐co‐EGDMA) showed absorption bands associated with ? C?O stretching at 1714 cm^?1, C? O? C stretching vibrations at 1152 cm^?1, and a broad band at 3500–3800 cm^?1 corresponding to ? OH stretching. Atomic force microscopy studies showed that the hydrogel containing 67% water had pores in the range of 3500–9000 nm, whereas the hydrogel containing 7% water did not show measurable pores. The hydrogel synthesized with 1% EGDMA showed 50% thallium‐201 release within the first 30 min and about 80% release within 60 min. In vitro insulin‐release studies suggested that the hydrogel with 27% water showed sustained release up to 120 min, whereas the hydrogels with 47 and 67% water showed that nearly all of the insulin was released within 60 min. Hydrogel devices synthesized with 27% water and filled with insulin particles showed sustained release for up to 8 days, whereas the hydrogels synthesized with 47 and 67% water released insulin completely within 3 days of administration. Animal studies suggested that the hydrogel devices synthesized with 27% water and filled with insulin‐loaded particles (120 IU) were able to control blood glucose levels for up to 5 days after implantation. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electrochemical preparation of poly(2‐bromoaniline) and poly(aniline‐co‐2‐bromoaniline) in acetonitrile

Electrochemical preparation of poly(2‐bromoaniline) (PBrANI) and poly(aniline‐co‐2‐bromoaniline) [P(An‐co‐2‐BrAn)] was carried out in an acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The cyclic voltammograms during the copolymerization had many features similar to those for the usual polymerization of aniline. The copolymer exhibits a higher dry electrical conductivity value than that of PBrANI and a lower one than that of PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of bromine moieties into the polyaniline chain. The structure and properties of the polymer and copolymer were elucidated using cyclic voltammetry (CV), FTIR, and UV‐vis spectroscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2460–2468, 2003     

Actual air separation through poly(aniline‐co‐toluidine)/ethylcellulose blend thin‐film composite membranes

Several multilayer thin‐film composite membranes were fabricated of ethylcellulose (EC) and poly(aniline‐co‐ortho‐toluidine) or poly(ortho‐toluidine) blend as selective thin films and three ultrafiltration membranes with a 10‐ to 45‐nm pore size and 100‐ to 200‐μm thickness as porous supports. The relationships between the actual air‐separation performance through the composite membranes and layer number, composition, casting solution concentration of the thin selective film are discussed. The oxygen‐enriched air (OEA) flux through the composite membranes increases steadily with increasing operational temperature and pressure. The oxygen concentration enriched by the composite membranes appears to decrease with operating temperature, but increases with operating pressure. The actual air‐separation property through the composite membranes seems to remain nearly constant for at least 320 days. The respective highest OEA flux, oxygen flux, and oxygen concentration, respectively, were found to be 4.78 × 10⁻⁵ cm³ (STP)/s · cm², 2.2 × 10⁻⁵ cm³ (STP)/s · cm², and 46% across EC/poly(o‐toluidine) (80/20) blend monolayer thin‐film composite membranes in a single step at 20°C and 650 kPa operating pressure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 458–463, 2000