Ethylene polymerization using a novel MgCl2/SiO2‐supported Ziegler–Natta catalyst

A novel MgCl₂/SiO₂‐supported Ziegler–Natta catalyst was prepared using a new one‐pot ball milling method. Using this catalyst, polyethylenes with different molecular weight distributions were synthesized. The effects of the [Si]/[Mg] ratio, polymerization temperature and [Al]/[Ti] ratio on the catalytic activity, the kinetic behaviour and the molecular weight and the polydispersity of the resultant polymer were studied. It was found that the polydispersity index of the polymer could be adjusted over a wide range of 5–30 through regulating the [Si]/[Mg] ratio and polymerization temperature, and especially when the [Si]/[Mg] ratio was 1.70, the polydispersity index could reach over 25. This novel bi‐supported Ziegler–Natta catalyst is thus useful for preparing polyethylene with a required molecular weight distribution using current equipment and technological processes. Copyright © 2005 Society of Chemical Industry     

Preparation of novel MgCl2‐adduct supported spherical Ziegler–Natta catalyst for α‐olefin polymerization

In this article, preparation of novel MgCl₂‐adduct supported spherical Ziegler–Natta catalyst for α‐olefin polymerization is reported. The factors affecting the particle size (PS) and particle size distribution (PSD) of the prepared support were investigated. In this method, the internal donor added while preparing MgCl₂‐adduct support was supposed to act as a crosslinking agent. Therefore it provided a reasonable way to enhance the morphology and control the PS of the resultant polymer particles. The possible mechanism is discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 945–948, 2006     

High temperature polymerization of propylene catalyzed by MgCl2‐supported Ziegler–Natta catalyst with various cocatalysts

Four cocatalysts, referred to as ethylaluminoxanes, were synthesized by the reaction between triethylaluminium (AIEt₃) and water under various molar ratios of H₂O/Al at ?78°C. Aluminoxanes were used as cocatalysts for a MgCl₂‐supported Ziegler–Natta catalyst for propylene polymerization at temperatures ranging from 70 to 100°C. When the polymerization was activated by AlEt₃, the activity as well as the molecular weight and isotacticity of the resulting polymer gradually dropped as the temperature varied from 70 to 100°C. When ethylaluminoxane was employed as the cocatalyst, good activity and high molecular weight and isotacticity were obtained at 100°C. Furthermore, when the cocatalyst varied from AlEt₃ to ethylaluminoxane, the atactic fraction and polymer fraction with moderate isotacticity decreased and the high isotactic fraction slightly increased, which indicated that the variation of the cocatalyst significantly affects the isospecificity of active sites. It was suggested that the reactivity of the Al‐Et group and the size of the cocatalyst were correlated to the performance of the Ziegler–Natta catalyst at different temperatures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1978–1982, 2006     

Effect of diether as internal donor on MgCl2‐supported Ziegler–Natta catalyst for propylene polymerization

This article demonstrates the influence of the molar ratio between diether as internal donor and Magnesium dichloride in processing of the catalyst preparation on the catalytic performance for propylene polymerization with MgCl₂‐supported Ziegler–Natta catalyst. The effect of electron donor on catalyst is investigated. The experimental data find that diether content on catalyst increases and Ti content on catalyst decreases with the increase of diether/Mg molar ratio. This result indicates that diether as internal donor is not coordinated to Ti species but to Mg species on catalyst. The introduction of diether remarkably improves the catalytic activity. The extents of improvement closely connect with diether/Mg molar ratio. The stereospecificity of catalyst intensively depends on the structure of diether as internal donor. The possible model of multi‐active sites on heterogeneous Ziegler–Natta catalyst is proposed to explain these phenomena. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1399–1404, 2006     

Polymerization of propylene using MgCl2 (ethoxide type)/TiCl4/diether heterogeneous Ziegler–Natta catalyst

Heterogeneous Ziegler–Natta catalyst of MgCl₂ (ethoxide type)/TiCl₄/diether was prepared. 2,2‐Diisobutyl‐1,3‐dimethoxy propane (DiBDMP), diether, was used as internal donor. Slurry polymerization of propylene was carried out using the catalyst in dry heptane while triethylaluminium (TEA) was used as co‐catalyst. The co‐catalyst effects, such as catalyst molar ratio, polymerization temperature, H₂ pressure, external donor, triisobutylaluminium (TiBA) and monomer pressure, on the activity of the catalyst and isotacticity index (II) of the polymers obtained were studied. Rate of polymerization versus polymerization time is of a decay type with no acceleration period. There are an optimum Al/Ti molar ratio and temperature to obtain the highest activity of the catalyst. The maximum activity was obtained at 60 °C. Increasing the monomer pressure to 1 010 000 Pa linearly increased the activity of the catalyst. Addition of hydrogen to 151 500 Pa pressure increased activity of the catalyst from 2.25 to 5.45 kg polypropylene (PP) (g cat)^?1 h^?1 using 505 000 Pa pressure of monomer. The II decreased with increasing Al/Ti ratio, monomer pressure, hydrogen pressure and increased with increasing temperature to 60 °C, following with decrease as the temperature increases. Productivity of 11.55 kg (PP) (g cat)^?1 h^?1 was obtained at 1 010 000 Pa pressure of monomer and temperature of 60 °C. Addition of methyl p‐toluate (MPT) and dimethoxymethyl cyclohexyl silane (DMMCHS) as external donors decreased the activity of the catalyst sharply, while the II slightly increased. Some studies of the catalyst structure and morphology of the polymer were carried out using FTIR, X‐ray fluorescence, scanning electron microscopy and Brunauer–Emmett–Teller techniques. Copyright © 2005 Society of Chemical Industry     

Study of propylene polymerization catalyzed by a spherical MgCl2‐supported Ziegler–Natta catalyst system: The effects of external donors

Spherical MgCl₂‐supported Ziegler–Natta catalysts containing internal donors, such as diethyl phthalate, diisobutyl phthalate, and di‐n‐octyl phthalate, have been prepared. The effects of external donors, phenyltrimethoxysilane, phenyltriethoxysilane, and diphenyldimethoxylsilane, on the propylene polymerization catalyzed by these catalysts were studied. The results indicate that the external donors not only led to an increase in the isotactic index, but also affected the morphology of resultant polymer particles. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 738–742, 2005     

Copolymerization of ethylene–propylene using high‐activity bi‐supported Ziegler–Natta TiCl4 catalyst

Heterogeneous Ziegler–Natta TiCl₄ catalyst using MgCl₂ and SiO₂ as supports was prepared under controlled conditions. Mg(OEt)₂ was used as a starting material and was expected to convert to active MgCl₂ during catalyst preparation. Due to the high surface area and good morphological control, SiO₂ was chosen as well. Slurry copolymerization of ethylene and propylene (EPM) was carried out in dry n‐heptane by using the catalyst system SiO₂/MgCl₂/TiCl₄/EB/TiBA or TEA/MPT/H₂ at temperatures of 40–70°C, different molar ratios of alkyl aluminum : MPT : Ti, hydrogen concentrations, and relative and total monomers pressure. Titanium content of the catalyst was 2.96% and surface area of the catalyst was 78 m²/g. Triisobutyl aluminum (TiBA) and triethyl aluminum (TEA) were used as cocatalysts, while ethyl benzoate (EB) and methyl p‐toluate (MPT) were used as internal and external donors, respectively. H₂ was used as a chain‐transfer agent. Good‐quality ethylene propylene rubber (EPR) of rubber was obtained at the ratio of [TiBA] : [MPT] : [Ti] = 320 : 16 : 1 and polymerization temperature was 60°C. When TiBA was used as a cocatalyst, a higher and more rubberlike copolymer was obtained. For both of the cocatalysts, an optimum ratio of Al/Ti was obtained relative to the catalyst productivity. Ethylene content of the copolymer obtained increased with increasing TiBA concentration, while inverse results were obtained by using TEA. Addition of H₂ increased the reactivity of the catalyst. The highest product was obtained when 150 mL H₂/L solvent was used. Increasing temperature from 40 to 70°C decreased the productivity of the catalyst, while irregular behavior was observed on ethylene content. Relative pressure of P_P/P_E = 1.4 : 1 and total pressure of 1 atm was the best condition for the copolymerization. Polymers with ethylene contents of 25–84% were obtained. Increasing ethylene content of EPR decreased T_g of the polymer obtained to a limiting value. Viscosity‐average molecular weight (M_v) decreased with increasing temperature and TiBA and H₂ concentration. However, increasing the polymerization time increased the M_v. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2597–2605, 2004     

Molecular weight distribution of polyethylene catalyzed by Ziegler–Natta catalyst supported on MgCl2 doped with AlCl3

Ti‐based Ziegler–Natta catalysts supported on MgCl₂ doped with AlCl₃ were prepared by the reaction of MgCl₂/AlCl₃–ethanol adduct with TiCl₄. No AlCl₃ crystallites were found in the AlCl₃‐doped catalysts by WAXD analysis, suggesting that AlCl₃/MgCl₂ solid solution was formed. The effect of doping on the catalyst performance in ethylene polymerization was investigated. The results showed that the catalysts based on AlCl₃‐doped MgCl₂ support exhibited a slightly higher activity than did the MgCl₂‐supported catalyst and the molecular weight distribution (MWD) of polyethylene (PE) markedly increased (from 10.8 to 47.9) with the increase of AlCl₃ content in catalysts. The changes in catalyst's active center distribution were studied based on nonlinear fitting of the polymer GPC curves by multiple Flory functions. It was found that increase of types of active centers by introducing AlCl₃ into the support should be responsible for the broadening of MWD of PE. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1768–1772, 2006     

Prepolymerization of ethylene with a Ziegler–Natta catalyst

The slurry prepolymerization of ethylene using TiCl₄/MgCl₂ as a catalyst was investigated. A 2³‐factorial experimental design method was employed to study the effects of the temperature, hydrogen, and active cocatalyst‐to‐catalyst molar ratio (Al/Ti) on the catalyst activity, prepolymer melt flow index, and powder bulk density. All dependent variables increased when the active Al/Ti ratio increased from 1 to 2. The hydrogen–Al/Ti interaction had a significant effect on the prepolymer melt flow index and catalyst activity. The hydrogen (partial pressure ranging from 0.5 to 1.5 bar) and temperature (ranging from 60 to 80°C) variables as well as the hydrogen–temperature and hydrogen–temperature–Al/Ti interactions increased the prepolymer powder bulk density, which ranged from 0.11 to 0.373 g/cc. To find the reason for the prepolymer powder bulk density variation with the operating conditions, the particle size distribution and crystallinity of the prepolymers were determined. The increasing catalyst activity, ranging from 132 to 660 g of polyethylene/mmol of Ti, enhanced the weight percentage of fines, which ranged from 3 to 60, and decreased the average particle size, which ranged from 562 to 120 μm. This was the reason for the increasing prepolymer powder bulk density and could be due to the breakup of the prepolymer particles during prepolymerization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Stereospecific polymerization of olefins with supported Ziegler − Natta catalysts

The discovery of Ziegler ? Natta catalysts has been one of the greatest developments in technology for the synthesis of stereoregular polymers in both academy and industry since the 1950s. In particular, the development of the fourth generation Ziegler ? Natta catalyst with MgCl₂ as support brings a revolutionary improvement to the properties of manufactured polyolefins and stimulates people to explore the stereospecific polymerization of α‐olefin and diene monomers, which supplies the power to synthesize a new type of polyolefin materials. Although research on single‐site catalysts has attracted a lot of attention in recent years, the ‘old’ and conventional Ziegler ? Natta catalysts are still being developed vigorously due to their unique industrial advantages such as low cost, high catalytic efficiency and high stereospecificity. In this mini‐review, we mainly summarize the development of the conventional supported Ziegler ? Natta catalyst system and the stereoregular polyolefins synthesized with supported Ziegler ? Natta catalysts. © 2013 Society of Chemical Industry     

Novel magnetic polyethylene nanocomposites produced by supported nanometre magnetic Ziegler–Natta catalyst

This paper describes the preparation of novel magnetic polyethylene nanocomposites using a nanometre magnetic Ziegler–Natta catalyst. It was found that novel magnetic polyethylene nanocomposites can be obtained according to the following four steps: (1) preparation of nanometre magnetic particles; (2) reaction between AlR₃ and hydroxyls on the surface of nanometre magnetic particles to form anchor points  AlR₂; (3) addition of TiCl₄, Ti being coordinated to anchor points on the surface of nanometre magnetic particles to form polymerization active centres; (4) ethylene polymerization being carried out in situ on the surface of the nanometre magnetic particles to produce novel magnetic polyethylene nanocomposites. It is found that the activity of ethylene polymerization is essentially unaffected by polymerization temperature and polymerization time. © 2000 Society of Chemical Industry     

Synthesis of branched polyethylene by in situ polymerization of ethylene with combined iron catalyst and Ziegler–Natta catalyst

2,6‐Bis(imino)pyridyl iron catalyst and traditional Ziegler–Natta catalyst were combined together as tandem catalytic system, activated with the mixture of TEA and MAO, and used for synthesis of branched polyethylene by in situ polymerization of ethylene. The branched polyethylene with branches from 8/1000C to 29/1000C was produced by adjusting reaction conditions: the amount of TEA, MAO, iron catalyst used, and reaction temperatures. Not only the short branches such as ethyl and butyl but also the longer branches (hexyl and longer than hexyl) were detected in the products. The products exhibited higher molecular weight and broader molecular weight distribution than those obtained from metallocene catalysts, which would provide the materials excellent mechanical properties and processability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Polymerization of ethylene and ethylene/1-hexene over Ziegler–Natta/metallocene hybrid catalysts supported on MgCl2 prepared by a recrystallization method

MgCl₂ for use as a catalyst support was prepared by dissolution in methanol and recrystallization in n-decane, followed by vacuum-drying at 2,000 rpm. The prepared support was modified by treatment with alkylaluminum compounds. The activity profile of ethylene over the supported catalysts persisted for periods up to 1 h during the polymerization. The prepared Ziegler–Natta/metallocene hybrid catalysts exhibited the characteristics of both metallocene and Ziegler–Natta catalysts. The polymer produced by the hybrid catalysts gave bimodal peaks in differential scanning calorimetry analysis for ethylene and ethylene/1-hexene polymerization, suggesting that the polymer was composed of two different lamellar structures that were polymerized by each catalyst. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1707–1715, 1998     

Structure and morphology of polyethylene/polypropylene in‐reactor alloys synthesized by spherical high‐yield Ziegler–Natta catalyst

A series of spherical polyethylene/polypropylene (PE/PP) in‐reactor alloys were synthesized with spherical high‐yield Ziegler–Natta catalyst by sequential multistage polymerization in slurry. The morphology of PE/PP alloy granule was evaluated by optical microscopy, scanning electron microscopy, and transmission electron microscopy. The results show PE/PP in‐reactor alloy with excellent morphology, high porosity, and narrow distribution of the particle size. The PE/PP in‐reactor alloys show excellent mechanical properties with good balance between toughness and rigidity. It was fractionated into five fractions by temperature‐gradient extraction fractionation, and every fractionation was analyzed by FTIR, ¹³C‐NMR, DSC, and WAXD. The PE/PP in‐reactor alloy was found to contain mainly five portions: PP, PE, segmented copolymer with PP and PE segment of different length, ethylene‐b‐propylene copolymer, and an ethylene–propylene random copolymer. The characteristic chain structure leads to good compatibility between the fractions of the alloy that shows a multiphase structure. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2075–2085, 2007     

Novel stabilization system for polypropylene via the Ziegler–Natta catalyzed polymerization in the presence of aluminum aryloxide

The aluminum aryloxide was prepared via the reaction of phenolic antioxidant, 3‐(3,5‐di‐t‐butyl‐4‐hydroxyphenyl)‐N‐octadecylpropionamide, with triethyl aluminum. Propylene polymerization using supported Ziegler–Natta catalyst systems was carried out in the presence of the antioxidant or its aluminum aryloxide. Although the antioxidant gave rise to decrease in catalyst yield and change in hydrogen response, the aluminum aryloxide had no influence on the catalytic polymerization behavior, and thus the obtained polymer characteristics such as molecular weight, polydispersity, and meso pentad as a stereoregularity were comparable to that polymerized without the antioxidant and the aluminum aryloxide. Polypropylene obtained in the presence of the aluminum aryloxide was well stabilized for oxidation and its stability was over 1000 h at 100°C (estimated to be over 30 years at room temperature). © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1350–1358, 2006     

Studies on the preparation of new magnetic polyolefins using nanometer magnetic Ziegler–Natta catalyst

Nanometer magnetic particles were prepared through oxidizing Fe²⁺ in basic solution. Initially, using resultant nanometer magnetic powder as support, supported nanometer magnetic Ziegler–Natta catalysts were obtained. Through polymerization in situ on the surface of nanometer magnetic particles, a new kind of magnetic polyolefin that is different from both the composite plastics' magnet and the structure plastics' magnet was obtained. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2087–2090, 1999     

Morphological study of spherical MgCl2.nEtOH supported TiCl4 Ziegler‐Natta catalyst for polymerization of ethylene

Spherical MgCl₂·nEtOH was prepared by adducting ethanol to MgCl₂ using melt quenching method. Effect of molar ratio of [EtOH]/[MgCl₂] = 2.8–3.05 on the morphology and particle size of the MgCl₂·nEtOH were studied. The best adduct of spherical morphology was obtained when 2.9 mol ethanol to 1 mol MgCl₂ was used. An emulsion of dissolved MgCl₂ in ethanol was prepared in a reactor containing silicon oil. Stirrer speed of the emulsion and its transfer rate to quenching section that work at ?10 to ?40°C are affected by the particle size of the adduct particle. The adducted ethanol was partially removed with controlled heat primary to catalyst preparation (support). Treatment of the support with excess TiCl₄ increased its surface area from 13.1 to 184.4 m²/g. Heterogeneous Ziegler‐Natta catalyst system of MgCl₂ (spherical)/TiCl₄ was prepared using the spherical support. Scanning electron microscopy studies of adduct, support, and catalyst obtained shown spherical particles, however, the polyethylene particles obtained have no regular morphology. The behavior indicates harsh conditions used for catalyst preparation, prepolymerization, and polymerization method used. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3829–3834, 2006     

Effect of electron donors on 1,3‐butadiene polymerization by a Ziegler–Natta catalyst based on neodymium

High‐cis polybutadiene produced by catalyst systems based on a rare earth is an elastomer used to produce green tires. This type of tire presents lower rolling resistance, which allows higher fuel economy, and thus fewer chemical compounds are discharged into the atmosphere. In this work, the influence of electron donors [tetrahydrofuran (THF) and tetramethylethylenediamine (TMEDA)] present in the polymerization solvent on the microstructure and molecular weight characteristics of the polybutadiene produced by neodymium catalysts was studied. The catalyst synthesis was carried out in glass bottles for 1 h at a temperature between 5 and 10°C. The catalyst components were diisobutylaluminum hydride, neodymium versatate, and tert‐butyl chloride. The polymerization reaction was carried out for 2 h. The reaction temperature was kept at 70± 3°C. The addition of TMEDA or THF above a determined concentration reduced the catalytic activity, molecular weight, and concentration of cis‐1,4 units (<96%), whereas the polydispersity increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2539–2543, 2005     

Structure,processing, morphology,and property relationships of biaxially drawn Ziegler–Natta/metallocene isotactic polypropylene film

The structure, processing, morphology, and property relationships of biaxially drawn isotactic polypropylene (BOPP) film of mixed metallocene isotactic PP (m‐iPP) and Ziegler–Natta iPP (ZN‐iPP) homopolymer compositions are developed. The DSC and film drawing behavior show cocrystallization of the ZN‐iPP and m‐iPP components. The structure, processing, morphology, and property relations of ZN‐iPP/m‐iPP blends are compared with ZN‐iPP of varying isotacticities. The ZN‐iPP/m‐iPP blends exhibit reduced biaxial yield stress [σ_y(T)]. A fractional crystallinity model collapses the σ_y(T) data into a common normalized form over a range of draw temperatures, ZN‐iPP tacticities, and blend compositions. The simplified model is extended to define the interrelationships of yield activation and strain hardening behavior into regimes differentiated by characteristic draw stress (crystallinity) levels. Structure–property models are developed to explain the effect of draw temperature and resin–blend microstructure on the draw behavior, film stiffness, barrier, elongation, and synergies of the BOPP film processing–property balance. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2400–2415, 2001     

Liquid Pool Copolymerization of Propylene/1‐Butene with a MgCl2‐Supported Ziegler‐Natta Catalyst

Summary: Liquid pool propylene/1‐butene copolymerizations were carried out in a batch reactor with a high activity Ziegler‐Natta catalyst system. Experimental runs were performed to evaluate the effect of the 1‐butene content on the crystallinity and melt temperature of the polymer resins. According to the results, 1‐butene can be significantly incorporated into the polymer chain at high polymerization rates over the whole range of copolymer compositions, leading to a decrease in the melting temperature (T_m) of the polymer, when compared to the poly(propylene) homopolymer, allowing for reduction of the sealing initiation temperature. It was observed by GPC and MFI measurements that the average molecular weights and the polydispersity index of the copolymer significantly decreased when compared to the ones obtained from poly(propylene). Despite high polymerization rates, polymer particles with good morphological features were produced in all cases. It was also observed that the absence of an external electron donor led to low crystallinity values for both the poly(propylene) homopolymer and for copolymers with different fractions of 1‐butene, when compared to literature values frequently reported for polymer resins based on 1‐butene and propylene. The obtained results indicate that a family of bulk propylene/1‐butene copolymer grades can be successfully developed for packaging and film applications.

Surface morphology and molecular weight distribution (deconvoluted into Schulz‐Flory distributions) of the propylene/1‐butene copolymer.