Synthesis and properties of fluorinated polyimides from 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane and various aromatic dianhydrides

A novel aromatic diamine, 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane, containing a pendant polyfluorinated phenyl group, a trifluoromethyl group, and methyl groups ortho‐substituted to the amino groups in the structure was synthesized and characterized. The diamine was polymerized with several aromatic dianhydrides, including 3,3′,4,4′‐biphenyltetracarboxylic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, 4,4′‐oxydiphthalic anhydride, and 4,4′‐hexafluoroisopropylidene diphthalic anhydride, via a high‐temperature one‐step procedure to afford four polyimides (PIs) with inherent viscosities of 0.47–0.70 dL/g. The PIs exhibited excellent solubilities in a variety of organic solvents. They were soluble not only in polar aprotic solvents but in many common solvents, such as cyclopentanone, tetrahydrofuran, and even toluene at room temperature. The tough and flexible PI films cast from the PI solutions exhibited good thermal stabilities and acceptable tensile properties. The glass‐transition temperatures were in the range 312–365°C, and the 5% weight loss temperatures were all higher than 480°C in nitrogen. The films had tensile strengths in the range 76–99 MPa, tensile moduli of 2.2–2.8 GPa, and elongations at break of 5–8%. In addition, the PI films exhibited excellent transparency in the visible light region with cutoff wavelength as low as 302 nm and transmittance higher than 88% at the wavelength of 450 nm. The PI films showed low dielectric constants ranging from 2.50–2.68 and low moisture absorptions of less than 0.56%. The good combined properties of the PIs mainly resulted from the synergic effects of the different substituents. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and thermal,mechanical and gas permeation properties of aromatic polyimides containing different linkage groups

Two series of aromatic polyimides containing various linkage groups based on 2,7‐bis(4‐aminophenoxy)naphthalene or 3,3′‐dimethyl‐4,4′‐diaminodiphenylmethane and different aromatic dianhydrides, namely 4,4′‐(4,4′‐isopropylidenediphenoxy)bis(phthalic anhydride), 4,4′‐(hexafluoroisopropylidene)bis(phthalic anhydride), 3,3′,4,4′ benzophenonetetracarboxylic dianhydride, 9,9‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]fluorene dianhydride and 4,4′‐(4,4′‐hexafluoroisopropylidenediphenoxy)bis(phthalic anhydride), were synthesized and compared with regard to their thermal, mechanical and gas permeation properties. All these polymers showed high thermal stability with initial decomposition temperature in the range 475–525 °C and glass transition temperature between 208 and 286 °C. Also, the polymer films presented good mechanical characteristics with tensile strength in the range 60–91 MPa and storage modulus in the range 1700–2375 MPa. The macromolecular chain packing induced by dianhydride and diamine segments was investigated by examining gas permeation through the polymer films. The relationships between chain mobility and interchain distance and the obtained values for gas permeability are discussed. © 2014 Society of Chemical Industry     

Preparation and properties of novel fluorinated polyimides based on 2,2′,6,6′-tetrafluorobenzidine

Fluorinated polyimides were prepared from 2,2′,6,6′-tetrafluorobenzidine and four conventional dianhydride monomers by a solution polycondensation reaction followed by a chemical imidization. Polyimide based on 2,2′,6,6′-tetrafluorobenzidine and hexafluoroisopropylidene bis(3,4-phthalic anhydride) (6FDA) is soluble in organic solvents such as NMP, DMA, DMF, THF, chloroform, and acetone while those based on 2,2′,6,6′-tetrafluorobenzidine and pyromellitic dianhydride (PMDA), benzophenone-3,3′,4,4′-tetracarboxylic acid dianhydride (BTDA), diphenylether-3,3′,4,4′-tetracarboxylic acid dianhydride (ETDA) are not. Polyimide from 2,2′,6,6′-tetrafluorobenzidine and 6FDA possesses high optical transparency at 350–700 nm and has a in-plane refractive index of 1.558 at 632.8 nm. All polyimides exhibit glass transition temperatures above 350°C. They also possess very high thermal stability. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1605–1609, 1998     

Soluble and light‐colored polyimides from 2,3,2′,3′‐oxydiphthalic anhydride and aromatic diamines

A series of polyimides were prepared from 2,3,2′,3′‐oxydiphthalic anhydride (3,3′‐ODPA) with various aromatic diamines via three different synthetic procedures. The one‐step and two‐step methods with the thermal imidization of poly(amic acids) (PAAs) yielded polyimides with a relatively low inherent viscosity; these produced brittle films. The polyimides prepared by the two‐step method via the chemical imidization of PAA precursors exhibited a higher inherent viscosity and afforded tough and creaseable films. All the 3,3′‐ODPA based polyimides had a significantly higher solubility than the corresponding polyimides from 3,4,3′,4′‐oxydiphthalic anhydride. The films cast from 3,3′‐ODPA polyimides also showed high optical transparencies and less color, with an ultraviolet–visible absorption edge of 370–397 nm and low yellowness index values of 11.3–29.8. These polyimides exhibited glass‐transition temperatures in the range 211–289°C and showed no significant decomposition below 500°C under nitrogen or air atmospheres. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1352–1360, 2005     

Preparation and properties of organo‐soluble polyimides based on 4,4′‐diamino‐3,3‐dimethyldiphenylmethane and conventional dianhydrides

4,4′‐Diamino‐3,3′‐dimethyldiphenylmethane was used to prepare polyimides in an attempt to achieve good organo‐solubility and light color. Polyimides based on this diamine and three conventional aromatic dianhydrides were prepared by solution polycondensation followed by chemical imidization. They possess good solubility in aprotonic polar organic solvents such as N‐methyl 2‐pyrrolidone, N,N‐dimethyl acetamide, and m‐cresol. Polyimide from 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane and diphenylether‐3,3′,4,4′‐tetracarboxylic acid dianhydride is even soluble in common solvents such as tetrahydrofuran and chloroform. Polyimides exhibit high transmittance at wavelengths above 400 nm. The glass transition temperature of polyimide from 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane and pyromellitic dianhydride is 370°C, while that from 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane and diphenylether‐3,3′,4,4′‐tetracarboxylic acid dianhydride is about 260°C. The initial thermal decomposition temperatures of these polyimides are 520–540°C. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1299–1304, 1999     

Synthesis,characterization, and gas permeability of aromatic polyimides containing pendant phenoxy group

A diamine containing a pendant phenoxy group, 1-phenoxy-2,4-diaminobenzene, was synthesized and condensed with different aromatic dianhydrides [4,4′-oxydiphthalic dianhydride, 4,4′-(hexafluoroisopropylidene)diphthalic anhydride, 3,3′,4,4′-benzophenone tetracarboxylic dianhydride, 3,3′,4,4′-biphenyltetracorboxylic dianhydride, and pyromellitic dianhydride] by one-step synthesis at a high temperature in m-cresol to obtain polyimides in high yields. Most of the polyimides exhibited good solvent solubility and could be readily dissolved in chloroform, sym-tetrachloroethane, N,N-dimethylformamide, N,N-dimethylacetamide, and nitrobenzene. Their inherent viscosities were in the range of 0.33–1.16 dL/g. Wide-angle X-ray spectra revealed that these polymers were amorphous in nature. All these polyimides were thermally stable, having initial decomposition temperatures above 500°C and glass-transition temperatures in the range of 248–281°C. The gas permeability of 4,4′-oxydiphthalic dianhydride and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride based polyimides was investigated with pure gases: He, H₂, O₂, Ar, N₂, CH₄, and CO₂. A polyimide containing a  C(CF₃)₂ linkage showed a good combination of permeability and selectivity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and characterization of organosoluble polyfluorinated polyimides derived from 3,3′,5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane and various aromatic dianhydrides

A polyfluorinated aromatic diamine, 3,3′, 5,5′‐tetrafluoro‐4,4′‐diaminodiphenylmethane (TFDAM), was synthesized and characterized. A series of polyimides, PI‐1–PI‐4, were prepared by reacting the diamine with four aromatic dianhydrides via a one‐step high‐temperature polycondensation procedure. The obtained polyimide resin had moderate inherent viscosity (0.56–0.68 dL/g) and excellent solubility in common organic solvents. The polyimide films exhibited good thermal stability, with an initial thermal decomposition temperature of 555°C–621°C, a 10% weight loss temperature of 560°C–636°C, and a glass‐transition temperature of 280°C–326°C. Flexible and tough polyimide films showed good tensile properties, with tensile strength of 121–138 MPa, elongation at break of 9%–12%, and tensile modulus of 2.2–2.9 GPa. The polyimide films were good dielectric materials, and surface and volume resistance were on the order of a magnitude of 10¹⁴ and 10¹⁵ Ω cm, respectively. The dielectric constant of the films was below 3.0 at 1 MHz. The polyfluorinated films showed good transparency in the visible‐light region, with a cutoff wavelength as low as 302 nm and transmittance higher than 70% at 450 nm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1442–1449, 2007     

Investigations on the polyimides derived from unfunctionalized symmetric cyclopentyl‐containing alicyclic cardo‐type dianhydride

This study presents an investigation on polyimides derived from a unfunctionalized symmetric cyclopentyl‐containing alicyclic cardo‐type dianhydride with ester linkage 1,1‐bis(4‐(3,4‐dicarboxylbenzoyloxy)phenyl)cyclopentylene dianhydride (BDPCP) that was readily accessed starting from cyclopentanone through two steps in high yield. Two series of polyimides, Cardo‐type series (CPI‐x) and analogous aromatic series (ArPI‐x) were prepared from condensation of BDPCP and aromatic 3,3′,4,4′‐Oxydiphthalic dianhydride with four aromatic diamines, respectively. Comparative studies revealed that CPI polymers show more favorable properties including better solubility in organic solvents, higher transparency with lower cut‐off wavelength (λ₀) ranging in 395–375 nm than 425–405 nm, lower water absorption ranging in 0.66–1.14% and surface energy 23.71–32.77 mN/m than 1.01–1.28% and 29.52–41.99 mN/m of ArPI analogs. Meanwhile, CPI series exhibit considerable mechanical properties with tensile strengths ranging in 87.6–102.9 MPa, elongations at break 6.6–8.9%. Owing to the moderate strain in cyclopentyl ring, CPI series retain good thermal properties with the glass transition temperature (T_g) in the range of 217–271°C. Dynamic dielectric measurement revealed that Cardo‐type dianhydride BDPCP endows CPI‐4 film with lower dielectric constant (ε′) 3.34 at 1 MHz and 25°C and dielectric loss (ε′′) 0.0064 at 1 kHz and 25°C than 3.49 and 0.013 for ArPI‐4 film. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42670.     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry     

Synthesis and properties of polyimides derived from diamine monomer containing bi-benzimidazole unit

A new aromatic heterocyclic diamine monomer containing bi-benzimidazole unit, 2,2-bis(4′-aminophenyl)-5,5-bi-1H-benzimidazole, was synthesized from 2,2-bis(4′-nitrophenyl)-5,5-bi-1H-benzimidazole (BNPBBI) prepared via the reaction of 3,3′,4,4′-biphenyltetramine and p-nitrobenzaldehyde with a high yield. Their compositions and chemical structures containing polybenzimidazole backbone were characterized by FTIR, ¹H NMR and elemental analysis. A series of aromatic polyimides containing the heterocyclic moiety in the main chain were prepared by the reaction of BAPBBI with various aromatic dianhydrides of 3,3′,4,4′-biphenyltetracarboxylic dianhydride, 4,4′-oxydiphthalic anhydride or pyromellitic dianhydride. The polymers possess a high glass transition temperature of >415 °C and a good thermal stability up to 566 °C with a 5 % weight loss. The combination of polybenzimidazole and polyimide via introducing BAPBBI into the main chains provides the rigid structure, and macromolecular interactions are thus enhanced, resulting in the outstanding mechanical properties. These polyimides exhibit the strong tensile strength of 201 to 327 MPa, and the ultrahigh tensile moduli of 10.7 to 15.5 GPa without post stretching.     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Synthesis of thermostable polyamideimides and their properties

Thermostable polyamideimides with inherent viscosity of 1.02–1.50 dL/g were synthesized from reacting of diamine-terminated aromatic amide prepolymer with various diisocyanate terminated imide prepolymers. The imide prepolymer was prepared by using 4,4′-diphen-ylmethane diisocyanate to react with 3,3′,4,4′ benzophenonetetracarboxylic dianhydride, 3,3′,4,4′ sulfonyl diphthalic anhydride, or 4,4′-oxydiphthalic anhydride using the direct one-pot method to improve their solubility. Almost all of the polyamideimides were generally soluble in a wide range of organic solvents such as N,N-dimethylformamide, N,N-dimeth-ylacetamide, N-methyl-2-pyrrolidone, dimethyl sulfoxide, and pyridine at room temperature. Polymers with high imide content required high temperatures to dissolve. All polyamide-imides had a glass transition temperature of 223–352°C and showed a 10% weight loss temperature of 415–575°C in air and 424–583°C in nitrogen atmosphere. The tensile strength, elongation at break, and initial modulus of polymer films ranged from 61 to 108 MPa, 5 to 10% and 1.54 to 2.50 GPa, respectively. These copolymers were partly crystalline in structure as shown by X-ray pattern. © 1996 John Wiley & Sons, Inc.     

一类含甲基结构高透明聚酰亚胺的合成与性能研究

以2,6-二氨基甲苯、3,3'',4,4''-联苯四甲酸二酐、3,3'',4,4''-二苯醚四甲酸二酐为原料，间甲酚作为溶剂，经一步法高温共缩聚，制备一系列可溶性共聚型聚酰亚胺(MPI)。利用红外光谱（FTIR）、核磁共振波谱（1H NMR）、差式扫描量热仪（DSC）、热重分析仪（TGA）和紫外-可见光分度计（UV）等测试仪器对MPI进行结构与性能表征。结果表明：红外与核磁的数据说明成功合成了含甲基结构的聚酰亚胺；该系列的含甲基聚酰亚胺在室温下可溶于N-甲基吡咯烷酮（NMP）、N,N-二甲基乙酰胺（DMAc）、二氯甲烷（CH2Cl2）三氯甲烷（CHCl3）、二甲基亚砜（DMSO）等有机溶剂，具有良好的溶解性和成膜性，并随着联苯酐的含量增加溶解性降低；同时该系列MPI制得的薄膜具有良好的光学透过性能，在紫外光波长450 nm时的透过率均在74%以上，截止波长在350 nm左右；该系列MPI的起始分解温度均大于457 ℃，800 ℃氮气氛围中的焦炭产率均大于63%，玻璃化转变温度在260 ℃~285 ℃之间，表现出优异的热学性能。此外，MPI-1~MPI-4薄膜还具有良好的机械性能，其弹性模量在1.7~2.1 GPa，拉伸强度在89.7~120.6 MPa，断裂伸长率在19.7%~28.4%。     

Synthesis and characterization of some aromatic polyimides

The diamine 2‐methyl‐1,3‐bis(4‐aminophenyloxy)benzene was prepared via a nucleophilic substitution reaction and was characterized with Fourier transform infrared, elemental analysis, and ¹H‐ and ¹³C‐NMR spectroscopy. The prepared diamine was also characterized with single‐crystal analysis. The geometric parameters of C₁₉H₁₈N₂O₂ were in the usual ranges. The dihedral angles between the central phenyl ring and the two terminal aromatic rings were 88.9 and 91.6°. The crystal structure was stabilized by N? H···N hydrogen bonds. The diamine was then polymerized with 3,3′,4,4′‐benzophenone tetracarboxylic acid dianhydride, 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, 3,4,9,10‐perylenetetracarboxylic acid dianhydride, and pyromellitic dianhydride by either a one‐step solution polymerization reaction or a two‐step procedure. These polymers had inherent viscosities ranging from 0.61 to 0.85 dL/gm. Some of the polymers were soluble in most common organic solvents even at room temperature, and some were soluble on heating. The degradation temperatures of the resultant polymers fell in the range of 260–500°C in nitrogen (with only 10% weight loss). The specific heat capacity at 200°C ranged from 1.0 to 2.21 J g^?1 K^?1. The temperatures at which the maximum degradation of the polymer occurred ranged from 510 to 610°C. The glass‐transition temperatures of the polyimides ranged from 182 to 191°C. The activation energy and enthalpy of the polyimides ranged from 44.44 to 73.91 kJ/mol and from 42.58 to 72.08 kJ/mol K, respectively. The moisture absorption was found in the range of 0.23–0.71%. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Syntheses and properties of novel polyimides derived from 2‐(4‐Aminophenyl)‐5‐aminopyrimidine

2‐(4‐Aminophenyl)‐5‐aminopyrimidine (4) is synthesized via a condensation reaction of vinamidium salts and amidine chloride salts, followed by hydrazine palladium catalyzed reduction. A series of novel homo‐ and copolyimides containing pyrimidine unit are prepared from the diamine and 1,4‐phenylenediamine (PDA) with pyromellitic dianhydride (PMDA) or 3,3′,4,4′‐biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two‐step thermal imidization method. The poly(amic acid) precursors had inherent viscosities of 0.97–4.38 dL/g (c = 0.5 g/dL, in DMAc, 30°C) and all of them could be cast and thermally converted into flexible and tough polyimide films. All of the polyimides showed excellent thermal stability and mechanical properties. The glass transition temperatures of the resulting polyimides are in the range of 307–434°C and the 10% weight loss temperature is in the range of 556–609°C under air. The polyimide films possess strength at break in the range of 185–271 MPa, elongations at break in the range of 6.8–51%, and tensile modulus in the range of 3.5–6.46 GPa. The polymer films are insoluble in common organic solvents, exhibiting high chemical resistance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5871–5876, 2006     

Synthesis and characteristics of organic soluble photoactive polyimides

Soluble aromatic polyimides with inherent viscosities of 0.23–0.50 dL/g have been synthesized from 2,2-bis(3-amino-4-hydroxyphenyl) hexafluoropropane (BAPAF) and various aromatic tetracarboxylic dianhydrides. Almost all polyimides were soluble in a wide range of organic solvents, i.e., acetone, m-cresol, N,N-dimethylacetamide, N,N-dimethylformamide, N,N-dimethylsulfoxide, N-methyl-2-pyrolidone, methyl ethyl ketone, and tetrahydrofuran (except that polyimide deriven from 3,3′,4,4′-biphenyl tetracarboxylic dianhydride). Synthesized polyimides have a glass transition temperature in a range of 293 to 355°C, showing no appreciable weight loss up to 400°C in both air and nitrogen. These soluble polyimides exhibit high transparency in the UV visible region, with water absorption being between 3.6 to 5.7 wt %. They provide an aqueous base developable positive photoresist system when formulated with diazonaphthoquinone sensitizer. On the other hand, negative photoactive polyimides which are soluble in common organic solvents and optically transparent at a light of 365 nm wavelength, being obtained by reacting these soluble polyimides with methacryloyl chloride. Properties and characteristics of both positive and negative photoactive polyimides have been studied here. © 1994 John Wiley & Sons, Inc.     

Synthesis,characterization, thermal and optical properties of soluble polyimides derived from an unsymmetrical diamine

A new unsymmetrical diamine monomer, 2,4‐diaminophenyl [4′‐(2′′,6′′‐diphenyl‐4′′‐pyridyl)phenyl]ether, was successfully synthesized by nucleophilic substitution of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2′,6′‐diphenyl‐4′‐pyridyl) phenol. The diamine monomer was characterized by FTIR, ¹H and ¹³C NMR, and elemental analysis techniques and used for the preparation of novel polyimides (PIs) by reaction with commercially available tetracarboxylic dianhydrides such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs with inherent viscosities ranged from 0.43 to 0.48 dL/g were readily soluble in many organic solvents and afforded tough and flexible films by solution casting. These polymers exhibited T_gs between 237 and 294°C, and 10% weight loss temperatures in excess of 500°C with up to 56% char yield at 600°C in air. Their maximum fluorescence emission in dilute (0.2 g/dL) NMP solution appeared at 450 nm. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Design and synthesis of organosoluble and transparent polyimides containing bulky substituents and noncoplanar structures

A new diamine monomer, 3,3′‐diisopropyl‐4,4′‐diaminophenyl‐4″‐phenyltouene, was designed, synthesized, and then polymerized with five commercial dianhydrides to obtain a series of novel polyimides via a one‐step method. The obtained polymers showed excellent solubility in most common solvents, even in low‐boiling solvents, such as chloroform, dichloromethane, and tetrahydrofuran. They exhibited a high thermal stability with the glass‐transition temperature in the range 262–318°C and 10% weight loss temperatures in the range 464–488°C under a nitrogen atmospheres. Meanwhile, these polymer films also displayed a high optical transparency with a cutoff wavelength in the range 305–365 nm; prominent mechanical properties with a tensile strength of 65.6–94.9 MPa, a Young's modulus of 1.6–2.8 GPa, and an elongation at break of 9.3–13.7%; a low dielectric constant in the range of 2.91–3.18 at 1 MHz; and an outstanding hydrophobicity with a contact angle above 90.6°. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43266.     

Syntheses and properties of polyimides derived from diamines containing 2,5‐disubstituted pyridine group

A series of novel homo‐ and copolyimides containing pyridine units were prepared from the heteroaromatic diamines, 2,5‐bis (4‐aminophenyl) pyridine and 2‐(4‐aminophenyl)‐5‐aminopyridine, with pyromelltic dianhydride (PMDA), and 3,3′, 4,4′‐biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two‐step thermal imidizaton method. The poly(amic acid) precursors have inherent viscosities of 1.60–9.64 dL/g (c = 0.5 g/dL in DMAC, 30°C) and all of them can be cast and thermally converted into flexible and tough polyimide films. All of the polyimides show excellent thermal stability and mechanical properties. The polyimides have 10% weight loss temperature in the range of 548–598°C in air. The glass transition temperatures of the PMDA‐based samples are in the range of 395–438°C, while the BPDA‐based polyimides show two glass transition temperatures (T_g1 and T_g2), ranging from 268 to 353°C and from 395 to 418°C, respectively. The flexible films possess tensile modulus in the range of 3.42–6.39 GPa, strength in the range of 112–363 MPa and an elongation at break in the range of 1.2–69%. The strong reflection peaks in the wide‐angle X‐ray diffraction patterns indicate that the polyimides have a high packing density and crystallinity. The polymer films are insoluble in common organic solvents exhibiting high chemical resistance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1844–1851, 2006     

Synthesis of aromatic poly(urea‐imide) with heterocyclic side‐chain structure

The poly(urea‐imide) copolymers with inherent viscosity of 0.81–1.08 dL/g were synthesized by reacting aryl ether diamine or its polyurea prepolymer with various diisocyanate‐terminated polyimide prepolymers. The aryl ether diamine was obtained by first nucleophilic substitution of phenolphthalein with p‐chloronitrobenzene in the presence of anhydrous potassium carbonate to form a dinitro aryl ether, and then further hydrogenated to diamine. The polyimide prepolymers were prepared by using 4,4′‐diphenylmethane diisocyanate to react with pyromellitic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, or 3,3′,4,4′‐sulfonyldiphthalic anhydride by using the direct one‐pot method to improve their solubility, but without sacrificing thermal property. These copolymers are amorphous and readily soluble in a wide range of organic solvents such as N‐methyl‐2‐pyrrolidone, dimethylimidazole, N,N‐dimethylacetamide, dimethyl sulfoxide, N,N‐dimethylformamide, m‐cresol, and sulfolane. All the poly(urea‐imides) have glass transition temperatures in the range of 205–240°C and show a 10 wt % loss at 326–352°C in nitrogen and 324–350°C in air. The tensile strength, elongation at break, and initial modulus of these copolymer films range from 42 to 79 MPa, 5 to 16%, and 1.23 to 2.02 GPa, respectively. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1719–1730, 1999