Development of electrical conductivity with minimum possible percolation threshold in multi-wall carbon nanotube/polystyrene composites

A method is reported that involves the bulk polymerization of styrene monomer in the presence of multi-wall carbon nanotubes (MWCNTs) and polystyrene (PS) beads, for the preparation of MWCNT/PS conducting composites with a significantly lower (0.08 wt.% MWCNT) percolation threshold than previously reported. Thus, the conductivities of 7.62 × 10⁻⁵ and 1.48 × 10⁻³ S cm⁻¹ were achieved in the MWCNT/PS composites through homogeneous dispersion of 0.08 and 0.26 wt.% CNTs, respectively in the in situ polymerized PS region by using 70 wt.% PS beads during the polymerization. The extent of dispersion and location of the MWCNTs in the PS matrix has been investigated with a scanning and transmission electron microscopy. The conductivity of the composites was increased with increasing wt.% of the PS beads at a constant CNT loading, indicating the formation of a more continuous network structure of the CNTs in PS matrix.     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of chemical functionalization of carbon nanotubes on their dispersibility in alkyl methacrylate polymer matrix

Nanocomposites based on poly(methyl methacrylate) (PMMA) and poly(methyl methacrylate‐co‐octadecyl methacrylate) (M/O) matrices and four different types of multiwall carbon nanotubes: pristine, oxidized (MWCNT–COOH), methyl ester (MWCNT–COOCH₃), and dodecyl ester (MWCNT–COOC₁₂H₂₅) functionalized, were prepared in situ by radical (co)polymerization. The effectiveness of preparation of nanocomposites regarding dispersion and distribution of various MWCNT in polymer matrices was sized by Scanning electron microscopy. In case of PMMA matrix, the best dispersion and distribution were accomplished for MWCNT–COOCH₃ due to their chemical resemblance with polymer matrix. After the introduction of 10 mol % of octadecyl methacrylate in polymer matrix a fairly good dispersion and distribution of MWCNT–COOCH₃ were retained. The addition of 1 wt % of MWCNTs caused a significant reduction in the degree of polymerization of the PMMA matrix. But at the same time, the present MWCNTs increased storage modulus of PMMA nanocomposites except for dodecyl ester functionalized MWCNT. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46113.     

Low percolation threshold and high electrical conductivity in melt‐blended polycarbonate/multiwall carbon nanotube nanocomposites in the presence of poly(ε‐caprolactone)

This study focuses on the electrical properties of polycarbonate (PC)/poly(ε‐caprolactone) (PCL)‐multiwall carbon nanotube (MWCNT) nanocomposites. MWCNTs were incorporated into thermoplastic PC matrix by simple melt blending using biodegradable PCL based concentrates with MWCNT loadings (3.5 wt%). Because of the lower interfacial energy between MWCNT and PCL, the nanotubes remain in their excellent dispersion state into matrix polymer. Thus, electrical percolation in PC/PCL‐MWCNT nanocomposites was obtained at lower MWCNT loading rather than direct incorporation of MWCNT into PC matrix. AC and DC electrical conductivity of miscible PC/PCL‐MWCNT nanocomposites were studied in a broad frequency range, 10¹?10⁶ Hz and resulted in low percolation threshold (p_c) of 0.14 wt%, and the critical exponent (t) of 2.09 from the scaling law equation. The plot of logσ_DC versus p^?1/3 showed linear variation and indicated the existence of tunneling conduction among MWCNTs. At low MWCNT loading, the influence of large polymeric gaps between conducting clusters is the reason for the frequency dependent electrical conductivity. Transmission electron microscopy and field emission scanning electron microscopy showed that MWCNTs were homogeneously dispersed and developed a continuous interconnected network path throughout the matrix phase and miscibility behavior of the polymer blend. POLYM. ENG. SCI., 54:646–659, 2014. © 2013 Society of Plastics Engineers     

Aramid–multiwalled carbon nanotube nanocomposites: effect of compatibilization through oligomer wrapping of the nanotubes

Aramid–multiwalled carbon nanotube (MWCNT) nanocomposites with different CNT loadings were prepared by the solution‐blending technique. Aramid oligomeric chains having reactive amine end‐groups were covalently grafted and wrapped over the surface of acid‐functionalized MWCNTs. The presence of functional groups and surface modification of MWCNTs were studied using Raman, Fourier transform infrared and X‐ray photoelectron spectroscopic and transmission/scanning electron microscopic techniques. Addition of these MWCNTs resulted in a homogeneous dispersion throughout the aramid matrix. Dynamic mechanical thermal analysis showed an increase in the storage modulus and the glass transition temperature involved with α‐relaxations on CNT loading. The coefficient of thermal expansion (CTE) of aramid was reduced on loading with such CNTs. Strong interfacial interactions of the matrix with the surface‐modified CNTs reduced the stress‐transfer problem in the composite material and resulted in higher modulus of 4.26 GPa and a glass transition temperature of 338.5 °C, whereas the CTE was reduced to 101.8 ppm °C^?1 on addition of only 2.5 wt% CNTs in the aramid matrix. © 2016 Society of Chemical Industry     

High electromagnetic interference shielding with high electrical conductivity through selective dispersion of multiwall carbon nanotube in poly (ε‐caprolactone)/MWCNT composites

This study presents the preparation of electrically conducting poly(ε‐caprolactone) (PCL)/multiwall carbon nanotube (MWCNT) composites with very low percolation threshold (p_c). The method involves solution blending of PCL and MWCNT in the presence of commercial PCL beads. The PCL beads were added into high viscous PCL/MWCNT mixture during evaporation of solvent. Here, the used commercial PCL polymer beads act as an ‘excluded volume’ in the solution blended PCL/MWCNT region. Thus, the effective concentration of the MWCNT dramatically increases in the solution blended region and a strong interconnected continuous conductive network path of CNT−CNT is assumed throughout the matrix phase with the addition of PCL bead which plays a crucial role to improve the electromagnetic interference shielding effectiveness (EMI SE) and electrical conductivity at very low MWCNT loading. Thus, high EMI SE value (∼23.8 dB) was achieved at low MWCNT loading (1.8 wt %) in the presence of 70 wt % PCL bead and the high electrical conductivity of ∼2.49×10⁻² S cm⁻¹ was achieved at very low MWCNT loading (∼0.15 wt %) with 70 wt % PCL bead content in the composites. The electrical conductivity gradually increased with increasing the PCL bead concentration, as well as, MWCNT loading in the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42161.     

Synthesizing multi‐walled carbon nanotube‐polymethyl methacrylate conductive composites and poly(lactic acid) based composites

Multi‐walled carbon nanotube was modified with polymethyl methacrylate (MWCNT‐PMMA) by in situ solution radical polymerization in the presence of 2,2′‐Azobis (isobutyronitrile) as an initiator. The products with different addition of methyl methacrylate (MMA) were pressed into slices to prepare specimens for electrical conductivity testing. It was found that the MWCNT‐PMMA nanocomposites demonstrate excellent electrical conductivity. To investigate the microsphere morphology and the colloidal surfactant of MWCNTs in MWCNT‐PMMA composites, samples were submitted to scanning electron microscopy and transmission electron microscopy. The thermogravimetric analysis of the prepared composites confirmed that MWCNTs as a thermal stabilizer for PMMA, which could have a wide range of potential applications, such as in catalysts, sensors, environmental remediation, and energy storage. Two series of poly(lactic acid) (PLA) based biocomposites with different MMA additions and MWCNT‐PMMA composites contents were prepared with twin‐screw extruding and injection molding. The results show the mechanical properties changed a little with the MMA and MWCNT‐PMMA composites contents increasing, which suggested the well compatibility between MWCNT‐PMMA composites and PLA. POLYM. COMPOS., 37:503–511, 2016. © 2014 Society of Plastics Engineers     

Electrical and mechanical tuning of 3D printed photopolymer–MWCNT nanocomposites through in situ dispersion

An electric field-assisted in situ dispersion of multiwall carbon nanotubes (MWCNTs) in polymer nanocomposites, fabricated through stereolithography three-dimensional (3D) printing technique, was demonstrated. The introduction of MWCNTs increased the elasticity modulus of the polymer resin by 77%. Furthermore, the use of an electric field for in situ MWCNT dispersion helped improving the average elongation at break of the samples with MWCNTs by 32%. The electric field also increased the ultimate tensile strength of the MWCNT reinforced nanocomposites by 42%. An increase of over 20% in the ultimate tensile strength of in situ dispersed MWCNT nanocomposites over the pure polymer material was observed. Finally, it was demonstrated that the magnitude and direction of the electrical conductivity of MWCNT nanocomposites can be engineered through the application of in situ electric fields during 3D printing. An increase of 50% in the electrical conductivity was observed when MWCNTs were introduced, while the application of the electric field further improved the electrical conductivity by 26%. The presented results demonstrated the feasibility of tuning both electrical and mechanical properties of MWCNT reinforced polymer nanocomposites using in situ electrical field-assisted 3D printing. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47600.     

Surfactant‐assisted processing of polyimide/multiwall carbon nanotube nanocomposites for microelectronics applications

The dispersion and stability of carbon nanotubes (CNTs) inside a polymer matrix, especially with a high CNT content, are still big challenges. Moreover, the interaction between CNTs and the polymer matrix should be strong enough to improve the mechanical properties. The efficient dispersion of CNTs is essential for the formation of a uniform distribution of a CNT network in a polymer composite. Polyimide/multiwall CNT nanocomposites were synthesized by in situ polymerization with the aid of a surfactant. A Fourier transform infrared spectroscopy study proved that the surfactant did not hamper the polymerization of the polyimide. The microstructure, storage modulus and electrical conductivity of the nanocomposites were improved using a particular amount of the surfactant. Environmental stability test results showed that the polyimide with 1 wt% of CNTs produced with the aid of the surfactant possessed excellent reliability in high‐temperature and high‐humidity environments. Surfactants were successfully used to obtain fine‐structure polyimide/CNT nanocomposites by in situ polymerization. The enhancement of the mechanical properties was attributed to the incorporation of the surfactant. A percolation of electrical conductivity could be achieved with 1 wt% of CNTs. Copyright © 2010 Society of Chemical Industry     

Thermal‐Insulation,Electrical, and Mechanical Properties of Highly‐Expanded PMMA/MWCNT Nanocomposite Foams Fabricated by Supercritical CO2 Foaming

Foaming behavior of poly(methyl methacrylate) (PMMA)/multi‐walled carbon nanotubes (MWCNTs) nanocomposites and thermally‐insulating, electrical, and mechanical properties of the nanocomposite foams are investigated. PMMA/MWCNT nanocomposites containing various amounts of MWCNTs are first prepared by combining solution and melt blending methods, and then foamed using CO₂. The foaming temperature and MWCNT content are varied for regulating the structure of PMMA/MWCNT nanocomposite foams. The electrical conductivity measurement results show that MWCNTs have little effect on the electrical conductivity of foams with large expansion ratio. Thermal conductivities of both solid and foamed PMMA/MWCNT nanocomposites are measured to evaluate their thermally insulating properties. The gas conduction, solid conduction, and thermal radiation of the foams are calculated for clarifying the effects of cellular structure and MWCNT content on thermal insulation properties. The result demonstrates that MWCNTs endowed foams with enhanced thermal insulation performance by blocking thermal radiation. Moreover, the compressive testing shows that MWCNTs improve the compressive strength and rigidity of foams. This research is essential for optimizing environmentally friendly thermal insulation nanocomposite foams with enhanced thermal‐insulation and compressive mechanical properties.     

Synergistic effect of dual nanofillers (MWCNT and Ni–Al LDH) on the electrical and thermal characteristics of polystyrene nanocomposites

The advantage of using 3D hybrid filler containing carboxylic acid functionalized multiwalled carbon nanotubes (c‐MWCNTs) and sodium dodecyl sulfate modified Ni–Al layered double hydroxide (sN‐LDH) over c‐MWCNTs and sN‐LDHs acting alone was investigated. PS/c‐MWCNT composites proved to be good for improvement of properties, but not to an appreciable level, especially in case of electrical conductivity, flame retardancy, rheology, and water vapor permeability. Hence, a combination of 0.3 wt % of c‐MWCNT and 3 wt % of sN‐LDH was optimized as additives to assist in the full expression of the filler traits in the nanocomposite and to obtain a versatile nanocomposite with properties specific to both the fillers. This approach slightly decreases the dispersion challenge faced with handling high loadings of CNT and also the intrinsic limitations specific to the individual fillers (i.e., inertness of CNTs and low conductivity of LDHs). Moreover, the anion/anionic repulsion of organically modified CNT/LDH facilitates effective dispersion of the additive opposing adhesion. FTIR and Raman spectroscopy provided evidence for incorporation and proper dispersion of the additives in the polymer matrix, with XRD and TEM confirming a well‐dispersed morphology of the nanocomposites. In this work, focus is made on the improvement of thermal stability, flame retardancy, melt rheology, hardness, electrical conductivity, and water vapor permeability of PS/0.3 wt % c‐MWCNT/3 wt % sN‐LDH nanocomposites over PS/0.3 wt % c‐MWCNT, making use of the synergistic effect of c‐MWCNT coupled with sN‐LDH on polystyrene. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46513.     

Preparation and properties of carbon nanotube/binary‐polymer composites with a double‐segregated structure

A carbon nanotube (CNT)/poly(methyl methacrylate) (PMMA)/ultrahigh molecular weight polyethylene (UHMWPE) composite containing a double‐segregated structure was formalized by means of a facile mechanical mixing technology. In the composite, the CNTs were decorated on the surfaces of PMMA granules, and the CNTs decorated granules formed the continuous segregated conducting layers at the interfaces between UHMWPE particles. Morphology observations confirmed the formation of a specific double‐segregated CNT conductive network, resulting in an ultralow percolation threshold of ～0.2 wt %. The double‐segregated composite containing only 0.8 wt % CNT loading exhibited a high electrical conductivity of ～0.2 S m^?1 and efficient electromagnetic shielding effectiveness of ～19.6 dB, respectively. The thermal conductivity, temperature‐resistivity behaviors, and mechanical properties of the double‐segregated composites were also studied. This work provided a novel conductive network structure to attain a high‐performance conducting polymer composite at low filler loadings. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39789.     

Effect of clay platelet dispersion as affected by the manufacturing techniques on thermal and mechanical properties of PMMA‐clay nanocomposites

In this work, the properties of Poly(methyl methacrylate) (PMMA)‐clay nanocomposites prepared by three different manufacturing techniques viz., solution mixing, melt mixing, and in‐situ bulk polymerization in presence of clay were studied. Morphological analysis revealed that the extent of intercalation and dispersion of the nanoclay were relatively higher in the in‐situ polymerized nanocomposites than those of solution and melt blended nanocomposites. Differential Scanning Calorimetric study indicated maximum increment in T_g of the PMMA in the in‐situ polymerized PMMA‐clay nanocomposites. Thermo gravimetric analysis showed improved thermal stability of PMMA in all the nanocomposites and the maximum improvement was for in‐situ polymerized nanocomposites. The storage moduli of all the nanocomposites were higher than the pure PMMA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic cure kinetics of epoxy/TiO2/MWCNT hybrid nanocomposites

The effect of multi-walled carbon nanotubes (MWCNTs) on cure kinetic parameters of the epoxy/amine/TiO₂ (1 wt%) resin system was studied dynamically at four heating rates using DTA. The presence of MWCNT in various amounts (0.1, 0.2, 0.4 and 0.6 wt%) neither retarded nor accelerated the cure reaction of the epoxy/amine/TiO₂ system in a considerable extent. Addition of MWCNTs increased the extent of cure of the corresponding nanocomposites, especially at higher contents up to 0.4 wt% MWCNT filled composite. However, increasing the MWCNT content to 0.6 wt% adversely affected the extent of cure due to nanoparticle agglomeration. The fracture surface morphology of the nanocomposites revealed that the cracks deviated on reaching the MWCNTs, while propagating in the polymer matrix. Fractional extent of conversion (α) was calculated using genetic algorithm. Flynn–Wall–Ozawa and Kissinger methods were used to analyze the kinetic parameters. The presence of MWCNTs did not affect the autocatalytic cure mechanism of epoxy/amine/TiO₂ resin system and also did not cause any considerable barrier effect on the curing process. Activation energy data fitted well in the cubic polynomial regression equations and the changes of E _a with respect to α proved the autocatalytic cure mechanism, being followed by all the MWCNT-containing epoxy-based hybrid nanocomposites.     

Preparation of conducting composites of polypyrrole using supercritical carbon dioxide

Supercritical carbon dioxide, saturated with pyrrole, was brought into contact with oxidant‐impregnated films of poly(chlorotrifluoroethylene) (PCTFE), crosslinked poly(dimethylsiloxane) (PDMS), poly(methyl methacrylate) (PMMA), and porous crosslinked polystyrene (PS) in order to form conducting composites via the in situ polymerization of pyrrole. The two nonporous hosts—PCTFE and crosslinked PDMS—did not form conducting composites with polypyrrole (PPy). On the other hand, the electrical conductivity of the PPy composites with carbon dioxide‐swollen PMMA and porous PS ranged from 1.0 × 10^?4 S/cm to 3.0 × 10^?5 S/cm. In these two cases, the level of pyrrole polymerized on the surface or in the pores of the host polymer was sufficient to attain the interconnected conducting polymer networks necessary for electrical conductivity. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1113–1116, 2003     

Preparation of biocompatible multi‐walled carbon nanotubes as potential tracers for sentinel lymph nodes

Carbon nanotubes (CNTs) are capable of traversing cellular membranes by endocytosis and are therefore promising materials for use in imaging and drug delivery. Unfortunately, pristine CNTs are practically insoluble and tend to accumulate inside cells, organs and tissues. To overcome the poor dispersibility and toxicity of pristine CNTs, hydrophilic functionalization of CNTs has been intensively investigated. Water‐soluble multi‐walled carbon nanotubes (MWCNTs) were prepared by in situ polymerization of acrylic acid in a poor solvent for poly(acrylic acid) (PAA). The solvent type influenced the grafted density and chain length of PAA. MWCNTs with a high grafted density of PAA (22 wt%) could be well dispersed in water, NaCl aqueous solution (0.9 wt%) and cell culture media. The in vitro cytotoxicity of these MWCNTs for endothelial cells is reasonably low even at high concentration of PAA‐g‐MWCNT (70 µg mL^?1). The experimental results show that the biocompatibility of these MWCNTs is sufficient for biological applications. PAA‐g‐MWCNTs were successfully utilized for lymph node tracing. Experimental results suggest that PAA‐g‐MWCNTs have potential to be used as a vital staining dye, which may simplify the identification of lymph nodes during surgery. Copyright © 2009 Society of Chemical Industry     

Effect of cooling rate on the surface resistivity of polymer/multi‐walled carbon nanotube nanocomposites

In this study, ethylene‐vinyl acetate copolymer (EVA) and polystyrene (PS) were melt‐mixed with multi‐walled carbon nanotube (CNT) (MWCNT), respectively. The effect of mixing time, rotor speed, and cooling rate on surface resistivity was investigated. EVA/MWCNT and PS/MWCNT nanocomposites with percolation threshold <1 wt% of MWCNT were prepared using conventional melt‐compounding method. When fast cooling was applied for these nanocomposites, a surface resistivity of 10⁶ Ω/square was obtained at around 7 wt% of MWCNT for EVA and 10⁵ Ω/square at around 3.5 wt% of MWCNT for PS. However, when slow cooling was applied, a surface resistivity of 10⁶ Ω/square was obtained at 0.75 wt% of MWCNT for EVA and 10⁵ Ω/square at around 0.5 wt% of MWCNT for PS. To the best of our knowledge, this is the first report which recognizes the importance of cooling rate on the surface resistivity of polymer/MWCNT nanocomposites. This finding may be potential to the commercialization of the CNT‐based polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effect of carbon nanotube dispersion on electrochemical and mechanical characteristics of poly(methyl methacrylate)‐based gel polymer electrolytes

Polymer‐based electrolyte of lithium ion batteries and other devices have shortcomings of low ionic conductivity and inadequate mechanical strength. The study presents the preparation of polymethyl methacrylate (PMMA)‐based three‐layered nanocomposite gel polymer electrolytes (NCGPEs) having multiwalled carbon nanotubes (MWCNTs) dispersed in the middle layer of the composites and the effect of dispersoid quantities on the ionic, mechanical, and thermal characteristics of the electrolytes. The NCGPEs were synthesized by solution cast process with the various MWCNTs contents of 0.5, 1.0, 1.5, and 2.0 wt%. Morphology of the NCGPEs has been observed by scanning and transmission electron microscopes (SEMs). Interactions between the constituents of the composite and structural changes of the base polymer were investigated by Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) techniques. The mechanical strength of the NCGPEs increases considerably owing to the dispersion of MWCNTs and the highest strength was found for the dispersion of 2.0 wt% of MWCNTs. The thermal stability of the nanocomposites was investigated by thermo‐gravimetric analysis (TGA). The chemical decomposition temperature of the nanocomposites increases considerably as compared to the gel polymer electrolyte. Ionic conductivity of the composite electrolyte increases with the increase in addition of MWCNTs and the maximum ionic conductivity (10⁻³ S cm⁻¹) of the nanocomposite has been found with the dispersion of 2.0 wt% MWCNTs among all the dispersoid. POLYM. COMPOS., 37:1936–1944, 2016. © 2015 Society of Plastics Engineers     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers