Effect of copolymerization on crystallization kinetics of semicrystalline polyimides

Isothermal melt crystallization kinetics and nonisothermal cold crystallization kinetics of co‐PI based on 3, 3′, 4, 4′‐biphenyltetracarboxylic dianhydride (s‐BPDA)/1, 3‐bis‐(4‐aminophenoxy) benzene (TPER)/4, 4′‐oxydianiline(4, 4′‐ODA), and TPER PI (s‐BPDA/TPER) have been investigated. Avrami equation was used to analyze isothermal melt crystallization progress of TPER PI and co‐PI, primary crystallization processes was found to be changed as the introduction of 4, 4′‐ODA. Total activation energy ΔE for TPER PI and co‐PI were found to be ?404 and ?86 kJ mol^?1 by Arrhenius equation. Jeziorny's analysis, Ozawa's analysis, and Mo's approach were used to investigate nonisothermal cold crystallization progress of TPER PI and co‐PI. Activation energy ΔE_non for TPER PI and co‐PI were found to be 247 and 193 kJ mol^?1 by Kissinger equation. The result indicated that co‐PI exhibited lower crystallization rate than TPER PI when isothermally crystallized from melt, but higher crystallization rate under cold nonisothermal crystallization progress. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemical modification of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride polyimides by a catechol‐derived bis(ether amine)

Having previously demonstrated that the polyimide derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 1,2‐bis(4‐aminophenoxy)benzene [termed triphenyl ether catechol diamine (TPEC)] exhibited superior tensile properties in addition to good thermal properties, we now provide a preliminary assessment of the properties of the copolyimides prepared from BPDA, TPEC, and another aromatic diamine. The homopolyimides derived from BPDA and many aromatic diamines generally possessed good mechanical properties and thermal properties; however, they were insoluble in available organic solvents. In several cases, organosoluble BPDA copolyimides could be prepared from BPDA and equimolar mixtures of TPEC and another aromatic diamine. All the copolyimides could be formed into tough films with high moduli and strengths and, in most cases, high extensions to break. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 351–358, 2002; DOI 10.1002/app.10342     

Preparations and properties of a high performance semicrystalline copolyimide and composites reinforced with glass fiber

A semicrystalline copolyimide derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA), 1,3‐bis‐(4‐aminophenoxy)benzene (TPER), and 4,4′‐oxydianiline (4,4′‐ODA), end capped with phthalic anhydride (PA), was synthesized. Glass fiber reinforced composite was also prepared by impregnating powdery glass fiber with poly(amic acid) followed by solution imidization techniques. This copolyimide displayed a glass transition temperature of 202°C and a melting temperature of 373°C by differential scanning colorimeter (DSC). Crystallization and melting behaviors were investigated under nonisothermal and isothermal crystallization conditions. Double exothermic peaks were found by DSC when the copolyimide was cooled from the melt and multiple melting behaviors can be observed after the coployimide had been isothermally crystallized at different temperatures. Mechanical properties were investigated by dynamical mechanical analysis (DMA) and tensile experiments. The samples were cured at different temperatures and then tested at different temperatures. Results indicated that the copolyimide and the composite showed excellent mechanical properties. Additionally, this copolyimide also showed lower melt viscosity by rheological analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40345.     

Characterization and thermal‐oxidative degradation behavior of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) prepared via direct esterification technique

A series of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)s (PETBBs) were prepared via direct esterification from the monomers of terephthalic acid (TPA), 4,4′‐biphenyl dicarboxylic acid (BPDA), and ethylene glycol (EG) with different molar ratios. The chemical compositions of the obtained PETBBs, investigated by H¹‐NMR, were identical with the feed ratio, and the high molecular weights of PETBBs were confirmed by GPC analysis. The glass transition, crystallization, and melting behavior of them were measured by DSC; the results indicated that, in the range of 5–25 mol% of BPDA addition, the glass transition temperature (T_g) increased almost linearly and the melting temperature (T_m) decreased with increasing content of BPDA unit. As expected, the crystallization of PETBB became difficult with increasing introduction of BPDA, explained by higher crystallization temperature and smaller crystallization enthalpy from the glassy state. This decrease of crystallization rate may be beneficial to film processing. Moreover, owing to the introduction of rigid‐rod BPDA unit, the initial and maximum thermal‐oxidative decomposition temperatures were enhanced. The kinetic analysis of the thermal‐oxidative degradation indicated that the apparent activation energies of degradation for these PETBBs became higher than that of PET. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

The pyrolysis behaviors of polyimide foam derived from 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride/4,4′‐oxydianiline

The thermal stability and pyrolysis behaviors of polyimide (PI) foam derived from 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA)/4,4′‐oxydianiline (4,4′‐ODA) in air and in nitrogen were studied. The decomposition products of PI foam were analyzed by thermogravimetry‐Fourier transform infrared spectroscopy (TG‐FTIR). Several integral and differential methods reported in the literatures were used in decomposition kinetics analysis of PI foam. The results indicated that the PI foam was easier to decompose in air than in nitrogen, with ～ 55% residue remaining in nitrogen versus zero in air at 800^oC. The main pyrolysis products were CO₂, CO, and H₂O in air and CO₂, CO, H₂O, and small organic molecules in nitrogen. The different dynamic methods gave similar results that the apparent activation energies, pre‐exponential factors, and reaction orders were higher in nitrogen than those in air. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of novel borosiloxane‐containing aromatic copolyimides with excellent thermal stability and low coefficient of thermal expansion

The properties of borosiloxane‐containing copolyimides with borosiloxane in the main chain and in the side chain were studied. Two series of borosiloxane‐containing copolyimides were synthesized by the reaction of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA ) and 2,3′,3,4′‐biphenyltetracarboxylic dianhydride (a‐BPDA ) with p ‐phenylenediamine (PDA ), 4,4′‐oxydialinine (4,4′‐ODA ) and different borosiloxane diamine monomers (BSiAs ). The synthesized borosiloxane‐containing copolyimides exhibited better solubility than borosiloxane‐free copolyimides and showed high glass transition temperatures (320–360 °C), excellent thermal stability (570–620 °C for T ₁₀), great elongation at break (10% ? 14%) and a low coefficient of thermal expansion (14–24 ppm °C^?1). More specifically, the copolyimides containing BSiA‐2 formed nano‐scale protrusions and the copolyimides containing BSiA‐1 formed micro‐scale protrusions. The contact angles of the copolyimides increased from 72° for neat copolyimide to 96° for 5% of borosiloxane in the main chain of the copolymer up to 107° for 10% of borosiloxane in the side chain of the copolymer. © 2017 Society of Chemical Industry     

Morphology of polyimide fibers derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 4,4′‐oxydianiline

As one member of high performance fibers, aromatic polyimide fibers possess many advantages, such as high strength, high modulus, high and low temperature resistance, and radiation resistance. However, the preparation of the high performance fibers is so difficult that the commercial fibers have not been produced except P84 with good flame retardancy. In this report, a polyimide was synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydianiline (ODA) and the fibers were prepared from its solution by a dry‐jet wet‐spinning process. The formation of the as‐spun fibers in different coagulation bath composition was discussed. Scanning electron microscope (SEM) was employed to study the morphology of the as‐spun fibers. As a result, the remnant solvent existed in the as‐spun fibers generated from coagulation bath of alcohol and water. There were many fibrils and microvoids with the dimension of tens of nanometers in the fibers. One could observe the obvious fibrillation and the drawn fibers. The measurement for the mechanical properties of the fibers with a drawing ratio of 5.5 indicated that tensile strength and initial modulus were 2.4 and 114 GPa, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 669–675, 2004     

Synthesis and properties of organosoluble polyimides derived from 2,2′‐dibromo‐ and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianilines

Two new aromatic diamines, 2,2′‐dibromo‐4,4′‐oxydianiline (DB‐ODA 4 ) and 2,2′,6,6′‐tetrabromo‐4,4′‐oxydianiline (TB‐ODA 5 ), have been synthesized by oxidation, bromination, and reduction of 4,4′‐oxydianiline (4,4′‐ODA). Novel polyimides 6a–f and 7a–f were prepared by reacting DB‐ODA ( 4 ) and TB‐ODA ( 5 ) with several dianhydrides by one‐step method, respectively. The inherent viscosities of these polyimides ranged from 0.31 to 0.99 dL/g (0.5 g/dL, in NMP at 30°C). These polyimides showed enhanced solubilities compared to those derived from 4,4′‐oxydianiline and corresponding dianhydrides. Especially, polyimides 7a , derived from rigid PMDA and TB‐ODA ( 5 ) can also be soluble in THF, DMF, DMAc, DMSO, and NMP. These polyimides also exhibited good thermal stability. Their glass transition temperatures measured by thermal mechanical analysis (TMA) ranged from 251 to 328°C. When the same dianhydrides were used, polyimides 7 containing four bromide substituents had higher glass transition temperatures than polyimides 6 containing two bromide substituents. The effects of incorporating more polarizable bromides on the refractive indices of polyimides were also investigated. The average refractive indices (n_av) measured at 633 nm were from 1.6088 to 1.7072, and the in‐plane/out‐of‐plane birefringences (Δn) were from 0.0098 to 0.0445. It was found that the refractive indices are slightly higher when polyimides contain more bromides. However, this effect is not very obvious. It might be due to loose chain packing resulted from bromide substituents at the 2,2′ and 2,2′,6,6′ positions of the oxydiphenylene moieties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

2,6‐Diamino‐4‐phenylphenol (DAPP) copolymerized polyimides: synthesis and characterization

Novel soluble copolyimides containing phenyl and hydroxyl pendant groups were synthesized from pyromellitic dianhydride (PMDA) and two diamines, 2,6‐diamino‐4‐phenylphenol (DAPP) and 4,4′‐oxydianiline (ODA), in various ratios via thermal imidization. The structures and physical properties of the copolyimides were characterized by FTIR, elemental analysis, DSC, dynamic mechanical analysis (DMA), TGA, a universal testing machine for stress–strain behaviour, and a dielectric analyzer to study the effect of DAPP on the physical properties of the modified polymers. Copolyimides containing more than 40 mol% DAPP were soluble in hot N‐methyl‐2‐pyrrolidone (NMP), dimethylacetamide (DMAc) and dimethylformamide (DMF), and possessed a high glass transition temperature (358 °C) and a high modulus (3.9 GPa). Introduction of the diamine DAPP could also reduce the dielectric constant. A segment of imide linkages could convert to benzoxazole linkages by decarboxylation at temperatures higher than 420 °C under vacuum. Although the heat‐treated polybenzoxazoles (PBOs) exhibited many good properties, they were found to be too rigid and brittle to be processable for microelectronic applications. Copyright © 2005 Society of Chemical Industry     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

Morphology,thermal properties,hydrophobicity and O2/N2 gas separation performance of 4,4′‐oxydiphthalic anhydride‐based polyimide/titania hybrids

Two 4,4′‐oxydiphthalic anhydride (ODPA)‐based polyimide (PI)/titania hybrid films with different morphologies were prepared through an in situ sol‐gel process. The precursor, poly(amic acid) (PAA), was synthesized using ODPA, diamine of 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP) or 4,4′‐diaminodiphenyl ether (ODA) and a suitable amount of dimethylformamide solvent. A mixture of tetraethylorthotitanate (Ti(OEt)₄) and acetylacetone with molar ratio of 1:4 was then added to the PAA solution and mixed thoroughly. Following curing, PI/titania hybrid membranes with different crosslinkages and Ti(OEt)₄ contents were prepared. PI hybrids with the longer BAPP diamine present different morphologies and property changes related to the Ti(OEt)₄ content from those of hybrids with the shorter ODA diamine. The morphologies of the two ODPA‐based PI/titania hybrids were studied with reference to the disruption of imide ring formation. Different crosslinked structures produced were identified using Fourier transform infrared analysis from the frequency shift of the C?O band and relative absorbance intensities of bands of C?O group and imide ring (? N?). Thermal properties, O₂/N₂ gas separation performance, contact angle, storage modulus, glass transition temperature and decomposition temperature of the PI hybrids were all found to be functions of the Ti(OEt)₄ content, crosslinked structure and PI type. Copyright © 2012 Society of Chemical Industry     

Surface segregation of siloxane containing component in polysiloxane‐block‐polyimide and s‐BPDA/ODA polyimide blends

Surface segregation in polymer blend systems between 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐diaminodiphenyl ether (s‐BPDA/ODA) polyimide and block copolymer based on polysiloxane‐block‐polyimide (SPI) has been investigated. These polyimide blends, having various compositions of the SPI, were processed by a solution casting method. The glass substrate used in the film‐casting process shows significant effect on the migration of surface segregated species to enrich the air‐exposed surface, whereas the more polar s‐BPDA/ODA tends to remain close to the polar glass substrate. X‐ray photoelectron spectroscopy reveals that even at low SPI concentration, the siloxane moieties in the block copolymer tend to segregate into the air side surface. Contact angle measurement evidently indicates an enrichment of the hydrophobic siloxane fraction on the blend film surface. The average water contact angle of glass side surface is 77°C whereas that of the air side is about 102°C in every blend ratio. This behavior confirms the surface segregation phase separation in these polymer blends. Finally, the surface morphology observed by atomic force microscopy also suggests segregation type of phase separation in these blend systems. POLYM. ENG. SCI., 47:489–498, 2007. © 2007 Society of Plastics Engineers.     

Effect of organosilica isomers on the interfacial interaction in polyimide/aromatic organosilica hybrids

We report the effect of organosilica precursor isomers on the interfacial interaction between polyimide and organosilica in polyimide/organosilica hybrid composite films. Poly(4,4′‐oxydianiline biphenyltetracarboxamic acid) (BPDA‐ODA PAA) was used as the polyimide precursor, while the organosilica was made using o‐substituted, m‐substituted, and p‐substituted phenyl organosilica precursor isomers. For the preparation of precursor hybrid films, BPDA‐ODA PAA and organosilica precursors were mixed and then the organosilica precursors were converted to corresponding organosilica via sol–gel process. Finally, these precursor films were converted to corresponding polyimide/organosilica hybrid films by the thermal imidization of BPDA‐ODA PAA, which results in poly(4,4′‐oxydianiline biphenyltetracarboximide) (BPDA‐ODA PI). The polyimide/organosilica hybrid films were characterized using three distinctive nuclear magnetic resonance spectroscopies (¹H NMR, ¹³C‐CPMAS‐NMR, and ²⁹Si‐MAS‐NMR), wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and peel strength measurement. We found that the m‐substituted phenyl organosilica shows poorer interfacial interaction with BPDA‐ODA PI than do the o‐ or p‐substituted phenyl organosilicas. It was observed, however, that the peel strength of the hybrid films against an aluminum substrate increased with increasing contents of organosilicas, regardless of the nature of the organosilica isomers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2507–2513, 2007     

Synthesis and properties of novel alicyclic‐functionalized polyimides prepared from natural—(D)‐camphor

In this article, a new alicyclic‐functionalized diamine, 1,3‐bis(4‐aminophenoxymethylene)‐1,2,2‐trimethylclopentane (BAMT) was successfully synthesized starting from natural —(D)‐camphor through four reaction steps of oxidation to offer a dicaboxylic acid, reduction to offer a diol, nucleophilic substitution to give a dinitro compound and then reduction to give the final diamine. Two alicyclic‐containing polyimides were prepared by polycondensing BAMT with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐oxydiphthalicanhydride (ODPA), respectively. For the studies of the structure–property relationships of the polyimides, one aromatic polyimide of 4, 4′‐oxydianiline (ODA) polycondensed with ODPA was prepared in comparison. The alicyclic‐containinig polyimides PI (BPDA‐BAMT) and PI (ODPA‐BAMT) maintain good thermal properties with glass transition temperatures (T_g) of 257°C and 240°C, and temperatures at 5% weight loss (T₅) of 443°C and 436°C in nitrogen, respectively. The alicyclic polyimides exhibit tensile strengths of 91.9–133 MPa, Young's moduli of 2.75—3.24 GPa, and elongations at break of 5.6–18%. Compared with the aromatic polyimide PI (ODPA‐ODA), PI (ODPA‐BAMT) shows improved transparency with the UV‐Vis transmittance at 500 nm over 80%. In addition, PI (ODPA‐BAMT) displays better solubility than PI (ODPA‐ODA), which has been confirmed by the bigger d‐spacing value of PI (ODPA‐BAMT) than that of PI (ODPA‐ODA) calculated from the Wide‐angle X‐ray Diffraction spectra. This study indicates that the renewable forestry compound, such as natural —(D)‐camphor, could be a good origin for the structural designing and preparation of alicyclic‐containing polyimides with outstanding combined features suitable for advanced microelectronic and optoelectronic applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of benzimidazole‐based low CTE block copolyimides

A series of block and random copolyimide films were synthesized from various molar ratios of two diamines, rigid 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (APBI) and flexible 4,4′‐oxydianiline (ODA) by polycondensation with dianhydride 3,3′,4,4′‐biphenyltetracarboxylic dianhydride. The contents of APBI ranged from 10 to 60 mol % in copolyimides. The copolyimide films obtained by thermal imidization of poly(amic acid) solutions, were characterized by TMA, DMA, TGA, DSC, wide‐angle X‐ray diffraction, FTIR, tensile testing, water uptake (WU), and dielectric constant measurements. Rigid heterocyclic diamine APBI with interchain hydrogen bonding capability, led to low coefficient of thermal expansion (CTE), high T_g, high thermal stability and better mechanical properties. Increasing the APBI mol % caused a gradual decrease in the CTE and increase in T_g, thermal stability and tensile strength properties of the copolyimides films. Moreover, significantly enhanced thermal and mechanical properties of the block copolyimides were also found as compared to random copolyimides. The block copolyimide with APBI content of 60 mol %, achieved excellent properties, that is, a low CTE (4.7 ppm/K), a high T_g at 377°C, 5% weight loss at 562°C and a tensile strength at 198 MPa. This can be interpreted because of comparatively higher degree of molecular orientation in block copolyimides. These copolyimides also exhibited better dielectric constant and WU. This combination of properties makes them attractive candidates for base film materials in future microelectronics. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis,characterization, and properties of low viscosity tetra‐functional epoxy resin N,N,N′,N′‐ tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane

Tetra‐functional epoxy resin N,N,N′,N′‐tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane (TGDEDDM) was synthesized and characterized. The viscosity of TGDEDDM at 25°C was 7.2 Pa·s, much lower than that of N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM). DSC analysis revealed that the reactivity of TGDEDDM with curing agent 4,4′‐diamino diphenylsulfone (DDS) was significantly lower than that of TGDDM. Owing to its lower viscosity and reactivity, TGDEDDM/DDS exhibited a much wider processing temperature window compared to TGDDM/DDS. Trifluoroborane ethylamine complex (BF₃‐MEA) was used to promote the curing of TGDEDDM/DDS to achieve a full cure, and the thermal and mechanical properties of the cured TGDEDDM were investigated and compared with those of the cured TGDDM. It transpired that, due to the introduction of ethyl groups, the heat resistance and flexural strength were reduced, while the modulus was enhanced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40009.     

Organosoluble polyimides derived from asymmetric 2‐substituted‐and 2,2′,6‐trisubstituted‐4,4′‐oxydianilines

We report a new method for the preparation of asymmetric diamines using 4,4′‐oxydianiline (4,4′‐ODA) as the starting material. By controlling the equivalents of bromination agent, N‐bromosuccinimide, we were able to attach bromide and phenyl substituents at the 2‐ or 2,2′,6‐positions of 4,4′‐ODA. Thus, four new asymmetric aromatic diamines, 2‐bromo‐4,4′‐oxydianiline (6), 2,2′,6‐tribromo‐4,4′‐oxydianiline (7), 2‐phenyl‐4,4′‐oxydianiline (8) and 2,2′,6‐triphenyl‐4,4′‐oxydianiline (9), were synthesized by this method. Their structural asymmetry was confirmed using ¹H NMR spectroscopy. Asymmetric polyimides (PI10–PI13) were prepared from these diamines and three different dianhydrides (pyromellitic dianhydride (PMDA), 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride) in refluxing m‐cresol. The formed polyimides, except PI10a derived from 6 and PMDA, were all soluble in m‐cresol without premature precipitation during polymerization. These polyimides with inherent viscosity of 0.41–0.96 dL g^?1, measured at a concentration of 0.5 g dL^?1 in N‐methyl‐2‐pyrrolidone at 30 °C, can form tough and flexible films. Because of the structural asymmetry, they also exhibited enhanced solubility in organic solvents. Especially, polyimides PI11a and PI13a derived from 7 and 9 with rigid PMDA were soluble in various organic solvents at room temperature. The structural asymmetry of the prepared polyimides was also evidenced from ¹H NMR spectroscopy. In the ¹H NMR spectrum of PI11a, the protons of pyromellitic moiety appeared in an area ratio of 1:2:1 at three different chemical shifts, which were assigned to head‐to‐head, head‐to‐tail and tail‐to‐tail configurations, respectively. These polyimides also exhibited good thermal stability. Their glass transition temperatures ranged from 297 to 344 °C measured using thermal mechanical analysis. © 2013 Society of Chemical Industry     

Residual stress and mechanical properties of polyimide thin films

Four different structure polyimide thin films based on 1,4‐phenylene diamine (PDA) and 4,4′‐oxydianiline (ODA) were synthesized by using two different dianhydrides, pyromellitic dianhydride (PMDA) and 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), and their residual stress behavior and mechanical properties were investigated by using a thin film stress analyzer and nanoindentation method. The residual stress behavior and mechanical properties were correlated to the morphological structure in polyimide films. The morphological structure of polyimide thin films was characterized by X‐ray diffraction patterns and refractive indices. The residual stress was in the range of ?5 to 38 MPa and increased in the following order: PMDA‐PDA < BPDA‐PDA < PMDA‐ODA < BPDA‐ODA. The hardness of the polyimide films increased in the following order: PMDA‐ODA < BPDA‐ODA < PMDA‐PDA < BPDA‐PDA. The PDA‐based polyimide films showed relatively lower residual stress and higher hardness than the corresponding ODA‐based polyimide films. The in‐plane orientation and molecularly ordered phase were enhanced with the increasing order as follows: PMDA‐ODA < BPDA‐ODA < BPDA‐PDA ～ PMDA‐PDA. The PDA‐based polyimides, having a rigid structure, showed relatively better‐developed morphological structure than the corresponding ODA‐based polyimides. The residual stress behavior and mechanical properties were correlated to the morphological structure in polyimide films. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

How the monomer concentration of polymerization influences various properties of polybenzimidazole: A case study with poly(4,4′‐diphenylether‐5,5′‐bibenzimidazole)

In this work, a series of poly(4,4′‐diphenylether‐5,5′‐bibenzimidazole)s (OPBIs) were synthesized from 4,4′‐oxybis(benzoic acid) and 3,3′,4,4′‐tetraaminobiphenyl through the variation of the initial monomer concentration with a solution polycondensation technique in a poly(phosphoric acid) medium. The resulting polymers were characterized by various techniques such as infrared (IR), nuclear magnetic resonance, dynamic mechanical analysis (DMA), and thermogravimetric analysis. The initial monomer concentration in the polymerization mixture played an important role in controlling the molecular weight of the resulting polymers. A temperature‐dependent IR study showed that the free movement of the ? NH group of the imidazole ring was blocked by the absorbed moisture. The DMA study showed that the glass‐transition temperature (T_g) varied with the molecular weight, and the presence of the ether linkage in the OPBI polymer backbone had a significant influence on T_g. A high‐molecular‐weight OPBI polymer tended to form a supramolecular organization, which influenced the thermal characteristic of the polymer. Photophysical studies demonstrated the fluorescent characteristics of the OPBI polymers in both solid and solution states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Copolycondensation of IPA/TPA,BPA, and 4,4′‐dihydroxydipehnylsulfone and 4,4′‐dicarboxydiphenylsulfone

Copolycondensations of IPA, TPA, bisphenol A (BPA), and several cimonomers were carried out to improve thermal properties, such as, the glass transition temperature (T_g) of the IPA/TPA (50/50)–BPA polyester. Among the comonomers examined, 4,4′‐Dihydroxydiphenylsulfone (BPS) and 4,4′‐Dicarboxydiphenylsulfone (DCDPS) having a strongly dipolar sulfonyl group in the chain were significantly effective. The favorable effect upon the T_gs was studied by varying the amounts of BPS and DCDPS incorporated into the copolymers. In the copolycondensation with BPS, two‐stage copolycondensation of BPA first and then BPS, the reverse order of reaction, and their spontaneous addition were examined to investigate the effect of distribution of the BPS unit segments in the copolymer upon the T_gs of the resulted copolymers. The distribution was briefly studied from distribution of the IPA/TPA‐BPA oligomers in the initial reaction using GPC. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 875–879, 2000