永磁同步电机直接转矩控制系统的仿真研究

文章分析了永磁同步电机直接转矩控制的原理,阐述传统直接转矩控制系统转矩脉动的缺点,本文将空间矢量脉宽调制技术引入永磁同步电机的直接转矩控制系统中,利用空间矢量的调制过程,可在相同的系统硬件条件下得到更多的、连续的电压空间矢量,进而得到对电机更准确的控制。仿真结果表明,该方案既保持了直接转矩控制快速动态响应,又减小了电机转矩的脉动。     

基于SVPWM的永磁同步电机直接转矩控制系统的建模与仿真

文章介绍了永磁同步电机直接转矩控制的原理,分析了传统直接转矩控制系统转矩脉动的缺点,并且将空间矢量脉宽调制技术引入永磁同步电机的直接转矩控制系统中,利用空间矢量的调制过程,可在相同的系统硬件条件下得到更多的、连续的电压空间矢量,进而得到对电机更准确的控制。仿真结果表明,该方案既保持了直接转矩控制快速动态响应,又减小了电机转矩的脉动。     

基于SVPWM的永磁同步电动机直接转矩控制

针对永磁同步电动机直接转矩控制系统转矩和定子磁链脉动问题,采用电压空间矢量脉宽调制(SVPWM)的永磁同步电动机直接转矩控制方法。根据在每一个控制周期内,计算出参考磁链和所估计磁链的偏差,选择相邻非零矢量和零矢量,并精确地计算出各自的作用时间,然后利用线性组合法将其合成为新的电压矢量。仿真结果表明,所提出的控制方案是有效的,明显地改善转矩和磁链脉动,并且有很好的动态和稳态性能。     

一种新型永磁同步电动机的直接转矩控制方法

基于永磁同步电动机的转矩和磁链方程，介绍了一种改进的直接转矩控制方法。在该控制方法中，引入了一种新的电压空间矢量调制技术，这种调制技术的特点是把电动机的转速作为开关表的一个输入量，实现了定子电压空间矢量的精确选择，有效的降低了转矩、定子磁链和定子电流的波动。仿真实验结果验证了这种控制方法的有效性。     

基于SVPWM的永磁同步电机直接转矩控制系统的研究

将空间矢量脉宽调制技术(SVPWM)引入到了永磁同步电机的直接转矩控制(DTC)当中,实现了电压空间矢量的连续调节。定子磁链近似为圆形,有效地解决了常规DTC系统电磁转矩脉动较大的问题。在MATLAB/Simulink环境下搭建了永磁同步电机基于SVPWM的直接转矩控制系统的模型,对电机的多种运行状态进行了仿真,验证了控制理论的正确性和有效性。     

基于预前控制异步电机直接转矩控制方案的研究

在传统异步电动机直接转矩控制方案中，由于负载的变化规律不可预测，因此其常会带来较大的开关频率的变化，为此提出了一种基于预前控制的异步电动机直接转矩控制的方法。该方法依据前一个周期的磁链和转矩误差，对下一个开关周期所应施加到异步电动机的定子电压矢量进行预测，然后借助空间矢量PWM的方法，合成此开关电压矢量。样机实验结果表明，该方案不但能维持逆变器的开关频率基本恒定，而且还具有比传统直接转矩控制更为优良的动静态特性。     

异步电机DTC系统脉动最小化研究

直接转矩控制具有控制简单、动态响应迅速、对参数变化鲁棒性强的特点,因此得到了广泛的应用。在传统的异步电动机直接转矩控制系统中,存在电压空间矢量对定子磁链幅值和磁通角的影响,特别是低速时系统脉动大。针对此问题,文章提出了一种的新的控制方法,该方法将磁链区间细分控制与电压矢量合成结合在一起,并通过引入模糊控制算法进一步提高了转矩响应时间,且减小了转矩脉动。仿真结果表明,本控制方法可以大大减小转矩脉动,具有较好的动静态性能。     

基于空间矢量调制的PMSM直接转矩控制研究

针对传统的直接转矩控制（DTC）出现的开关频率不恒定,磁链和转矩脉动大的问题,提出一种基于空间矢量调制的直接转矩控制（SVM-DTC）方法。该方法集合了直接转矩控制响应快、矢量控制连续平滑的优点,以永磁同步电机（PMSM）数学模型为基础,建立转矩、磁链双闭环PI控制回路。采用空间电压矢量调制策略,将转矩和磁链作为控制量。仿真结果表明,相对于传统的直接转矩控制,基于空间矢量调制的直接转矩控制方案的开关频率恒定,转矩、磁链脉动小,系统具有良好的动、静态性能,验证了该方法的可行性和有效性。     

基于磁链预测的永磁直驱风力发电机SVM-DTC技术

永磁直驱风力发电机传统直接转矩控制（DTC）通过查表法选择固定电压矢量来控制定子磁链和电磁转矩,导致磁链和转矩的双重控制要求不能同时兼顾,造成磁链和转矩脉动过大。针对传统DTC的不足,研究了一种永磁直驱风力发电机基于定子磁链预测的空间矢量脉宽调制（SVPWM）DTC方法,通过对下一个控制周期磁链矢量的预测计算需要补偿的电压矢量,并引入SVPWM模块代替查表法来合成该电压矢量。仿真和实验结果表明,此方案能明显降低磁链和转矩脉动,改善永磁直驱风力发电系统的控制性能。     

有关矢量控制和直接转矩控制的一些改进方案

用于感应电动机高性能转矩控制的主要方案有矢量控制和直接转矩控制。本文综述了对这些技术的改进方案。     

Concise modulation strategies for four-leg voltage source inverters

The continuous, discontinuous pulse-width modulation (PWM) schemes and a novel space vector modulation methodology are proposed in this paper for four-leg dc-ac inverters. Using a space vector definition that includes the zero sequence voltage component and partitioning the feasible sixteen modes into two separate sets - one set having zero sequence voltages with positive magnitudes and the other set with negative magnitudes - the novel space vector implementation technique is determined as also the discontinuous carrier based PWM scheme. For the continuous carrier based PWM scheme, the indeterminate defining output voltage equations expressed in terms of the existence functions of the switching devices are solved using an optimization technique. The modulation schemes determined are shown by experimental results to synthesis any desirable balanced or unbalanced three-phase voltage sets when operating in the linear modulation region.     

Space Vector Modulation Applied to Three-Phase Three-Switch Two-Level Unidirectional PWM Rectifier

This work presents a methodology to apply space vector modulation to a three-phase three-switch two-level Y-connected unidirectional pulsewidth modulation (PWM) rectifier. Converter switching stages are analyzed to determine switch control signals for space vector modulation. A switching sequence is proposed in order to minimize the number of switch commutations and to reduce the switching losses. Duty cycle functions are determined and the desired switching sequences are performed by a simple PWM modulator with no need of to determine the present sector of vector. For this propose is just necessary to impose the desired current sectors from input voltage references. The vector control structure used with the proposed modulation technique is also described. In order to validate the proposed modulation technique, experimental results are presented for a 20 kW prototype.     

基于矢量合成的三电平PWM整流器脉宽调制技术的研究

介绍了二极管中点箝位型三电平PWM整流器电路的拓扑结构和传统的空间矢量脉宽调制(SVPWM)的基本原理。分析了一种小矢量合成虚拟空间矢量的三电平SVPWM脉宽调制方法,并把它与基于冗余小矢量的中点电位滞环控制策略相结合,从而更好的控制中点电位的波动。为避免参考电压矢量在扇区切换中输出矢量突变,采用了一种首发矢量全部采用正小矢量或负小矢量的空间矢量调制算法。最后把调制策略应用到三电平整流器中进行仿真分析,仿真结果验证了调制策略的正确性和有效性。     

Space Vector Sequence Investigation and Synchronization Methods for Active Front-End Rectifiers in High-Power Current-Source Drives

Space vector pulsewidth modulation (PWM) schemes for the active front end of a high-power drive normally produce low-order and suborder harmonics due to the low switching frequency and the drifting of synchronization between the PWM waveform and the rectifier input frequency. To provide a synchronized PWM and achieve the best harmonic performance, different space vector sequences suitable for a current-source converter are investigated in this paper. Details on how to achieve the waveform symmetries with a minimum switching frequency for each sequence are discussed. A thorough comparison of the harmonic performance of different space vector sequences is carried out. An optimum space vector modulation method by switching between two best sequences is proposed to achieve the best line-current total harmonic distortion with reduced switching losses. In addition, two synchronization methods, namely a PWM frame regulation method and a direct digital phase-locked loop synchronization method, are proposed. Both methods are equally effective in providing tight synchronization of the PWM waveform with the rectifier input frequency. The work has been verified in simulation and experiment.     

空间矢量脉宽调制技术研究

介绍了空间矢量脉宽调制的基本原理及实现方法,利用Matlab对空间矢量脉宽调制(SVPWM)和正弦脉宽调制(SPWM)进行仿真研究,得到系统运行的理论波形。最后用DSP电机控制芯片TMS320LF2407A实现了空间矢量脉宽调制算法,给出了相应的结果。仿真和实验结果表明空间矢量脉宽调制方案正确可行,减少了系统的纹波,提高了系统的控制精度,而且算法简单,实现方便。     

Four-wire dynamic voltage restorer based on a three-dimensional voltage space vector PWM algorithm

A modified voltage space vector pulse-width modulated (PWM) algorithm for a four-wire dynamic voltage restorer (DVR) is described. The switching strategy based on a three-dimensional (3-D) /spl alpha//spl beta/O voltage space is applicable to the control of three-phase four-wire inverter systems such as the split-capacitor PWM inverter and the four-leg PWM inverter. In contrast to the conventional voltage space vector PWM method, it controls positive, negative and zero sequence components of the terminal voltages instantaneously. Three 3-D modulation schemes are analyzed with respect to total harmonic distortion (THD), weighted total harmonic distortion (WTHD), neutral line ripple and switching loss over the whole range of the modulation index when the DVR experiences both balanced and unbalanced sags with phase angle jumps. Experimental results from a 9 kW DVR system using a split-capacitor PWM inverter are presented to validate the simulation results.     

Space Vector Modulation for Two-Level Unidirectional PWM Rectifiers

This paper presents the concepts for application of space vector modulation to two-level unidirectional pulsewidth modulation (PWM) rectifiers, and a methodology for the use of this modulation is proposed and applied in three different groups of rectifiers. For each group of rectifiers, the converter switching stages are analyzed to determine switch control signals for space vector modulation. One switching sequence is proposed for all rectifiers in order to minimize the number of switch commutations and reduce the switching losses. Duty cycle functions are determined, and the desired switching sequences are performed by a simple PWM, without the need to determine the present sector of the vector. For this purpose, it is necessary to impose the desired current sectors from input voltage references only. In order to validate the proposed modulation techniques, simulation and experimental results are presented for a 20-kW prototype.      

A 3-D generalized direct PWM algorithm for multilevel converters

A three-dimensional (3-D) generalized direct pulse width modulation (PWM) algorithm is proposed for multilevel converters in a three-phase, four-wire system. It is proved to be equivalent to the newly proposed generalized 3-D space vector modulation (SVM). However, the direct PWM greatly simplifies the calculation process and is much easier to implement in digital controllers. The direct PWM can be used in all applications needing a 3-D control vector, such as active filters, uninterruptible power supplies, etc. Simulation and experimental results are given to show the validity of the proposed control strategy.     

Voltage modulation factor of the magnetic flux control PWM methodfor inverter

The voltage modulation factor of the magnetic flux control pulse-width modulation (PWM) method is discussed. The modulation factor is derived from a theoretical study on the flux locus produced from the inverter output voltage. The derivation is based on the fact that the fundamental component of the inverter output voltage is proportional to the radius of the flux locus. It is shown theoretically that the voltage modulation factor is expressed by the content of a zero vector in one cycle of the selected PWM pattern of the space vector expression. The modulation factor of the magnetic flux control PWM method is calculated. The modulation factor can be varied from zero to 12/π². The output voltage of the magnetic flux control PWM method can be controlled by the modulation factor linearly from zero up to overmodulation. The simulation and experimental results are also shown     

Optimal PWM design for high power three-level inverter throughcomparative studies

Comparative studies between harmonic elimination and optimal PWM strategies are given for high power three-level inverter feeding an induction motor. An effective PWM map construction method based on the valid region on the frequency modulation index plane is suggested. Thereby, an optimal map including asynchronous space vector PWM, harmonic elimination and optimal PWM method is generated covering all of the low, middle and high modulation index regions. The PWM map was designed for 1 MVA rated general purpose GTO inverter and implemented with a digital signal processor. Experimental results are presented for 10 kVA prototype