Effects of Amorphous and Crystalline SiO2 Additives on γ-Al2O3-to-alpha-Al2O3 Phase Transitions

This paper focused on the effects of various phases of SiO₂ additives on the γ-Al₂O₃-to-α-Al₂O₃ phase transition. In the differential thermal analysis, the exothermic peak temperature that corresponded to the theta-to-α phase transition was elevated by adding amorphous SiO₂, such as fumed silica and silica gel obtained from the hydrolysis of tetraethyl orthosilicate. In contrast, the peak temperature was reduced by adding crystalline SiO₂, such as quartz and cristobalite. Amorphous SiO₂ was considered to retard the γ-to-α phase transition by preventing γ-Al₂O₃ particles from coming into contact and suppressing heterogeneous nucleation on the γ-Al₂O₃ surface. On the other hand, crystalline SiO₂ accelerated the α-Al₂O₃ transition; thus, this SiO₂ may be considered to act as heterogeneous nucleation sites. The structural difference among the various SiO₂ additives, especially amorphous and crystalline phases, largely influenced the temperature of γ-Al₂O₃-to-α-Al₂O₃ phase transition.     

Reinvestigation of Al–Si Spinel Phase in Diphasic Al2O3–SiO2 Gel

Mechanical mixture of γ-Al₂O₃ and amorphous SiO₂, and diphasic Al₂O₃/SiO₂ gels of three different compositions were synthesized. They were subjected to heat treatment to various temperatures in the range 900°–1600°C. Qualitative X-ray diffraction data show that these diphasic gels do not crystallize to a combined mixture of θ-Al₂O₃ and α-Al₂O₃ polymorphs at the intermediate stage, prior to mullite formation. Estimated mullite formation data show that the course of its formation from mixed oxides was different from that of diphasic gels. Results are compared with previous findings and the concept of Al–Si spinel formation in the phase transformation of stoichiometric diphasic gel system is substantiated.     

Preparation of Nanometer-Sized α-Alumina Powders by Calcining an Emulsion of Boehmite and Oleic Acid

This study proposes a method to form ultrafine α-Al₂O₃ powders. Oleic acid is mixed with Al(OH)₃ gel. The gel is the precursor of the Al₂O₃. After it is mixed and aged, the mixture is calcined in a depleted oxygen atmosphere between 25° and 1100°C. Oleic acid evaporates and decomposes into carbon during the thermal process. Residual carbon prevents the growth of agglomerates during the formation of α-Al₂O₃. The phase transformation in this process is as follows: emulsion →γ-Al₂O₃→δ-Al₂O₃→θ-Al₂O₃→α-Al₂O₃. This process has no clear θ phase. Aging the mixed sample lowers the formation temperature of α-Al₂O₃ from 1100° to 1000°C. The average crystallite diameter is 60 nm, measured using Scherrer's equation, which is consistent with TEM observations.     

Analysis of Phase Distribution for Ceramic Coatings Formed by Microarc Oxidation on Aluminum Alloy

The phase distribution for ceramic coatings formed by microarc oxidation (MAO) on 2024 aluminum alloy was investigated using X-ray diffraction. The results showed that the ceramic coatings mainly consisted of α-Al₂O₃ and γ-Al₂O₃ phases. The percentage of α-Al₂O₃ gradually increased from the external surface to the interface between the coating and the substrate of samples. The surface layer of coatings mainly contained the γ-Al₂O₃ phase, and its fraction of the composition remained almost constant with oxidation time. It is believed that the difference in the amounts of α-Al₂O₃ and γ-Al₂O₃ phases in the different layers of coatings was caused by the various cooling rates of molten Al₂O₃, which temporarily existed in the microarc zone.     

Lowering Crystallization Temperatures by Seeding in Structurally Diphasic Al2O3-MgO Xerogels

Thermal reactions in 93% Al₂O₃-7% MgO and 95.8% Al₂O₃-4.2% MgO gels seeded with α-Al₂O₃, MgAl₂O₄, α-Fe₂O₃, and SiO₂, sols were investigated by differential thermal analysis to determine the extent of nucleation catalysis of solid-state reactions. Seeding with α-Al₂O₃ lowered the α-Al₂O₃ crystallization temperature in these xerogels by 100° to 150°C. Spinel seeds have much less effect on the γ-α transition, and α-Fe₂O₃ and SiO₂ seeds do not affect it significantly. Isostructural seeding of gels may therefore permit lower ceramic processing temperatures.     

Phase Transformation of Diphasic Aluminosilicate Gels

Aluminosilicate gels with compositions Al₂O₂/SiO₂ and 2 were prepared by gelling a mixture of colloidal pseudo-boehmite and a silica sol prepared from acid-hydrolyzed Si(OC₂H₅)₄. Upon heating the pseudo-boehmite transforms to γ-Al₂O₃ around 400°C, then to δ-Al₂O₃ at 1050°C, and at 1200°C reacts with amorphous SiO₂ to form mullite. Some twinned θ-Al₂O₃ forms before mullite. Nonstoichiometric specimens have a similar transformation sequence, but form mullite grains with inclusions of either Al₂O₃ or cristobalite, often associated with dislocation networks or micropores. Mullite grains are formed by nucleation and growth and have equiaxed shape.     

Kinetics and Microstructural Evolution of Heterogeneous Transformation of θ-Alumina to α-Alumina

Ultrafine (<0.1 μm) high-purity θ-Al₂O₃ powder containing 3–17.5 mol%α-Al₂O₃ seeds was used to investigate the kinetics and microstructural evolution of the θ-Al₂O₃ to α-Al₂O₃ transformation. The transformation and densification of the powder that occurred in sequence from 960° to 1100°C were characterized by quantitative X-ray diffractometry, dilatometry, mercury intrusion porosimetry, and transmission and scanning electron microscopy. The relative bulk density and the fraction of α phase increased with annealing temperature and holding time, but the crystal size of the α phase remained ∼50 nm in all cases at the transformation stage (≤1020°C). The activation energy and the time exponent of the θ to α transformation were 650 ± 50 kJ/mol and 1.5, respectively. The results implied the transformation occurred at the interface via structure rearrangement caused by the diffusion of oxygen ions in the Al₂O₃ lattice. A completely transformed α matrix of uniform porosity was the result of appropriate annealing processes (1020°C for 10 h) that considerably enhanced densification and reduced grain growth in the sintering stage. The Al₂O₃ sample sintered at 1490°C for 1 h had a density of 99.4% of the theoretical density and average grain size of 1.67 μm.     

Seeding of the Reaction-Bonded Aluminum Oxide Process

The effect of the initial α-Al₂O₃ particle size in the reaction-bonded aluminum oxide (RBAO) process on the phase transformation of aluminum-derived γ-Al₂O₃ to α-Al₂O₃, and subsequently densification, was investigated. It has been demonstrated that if the initial α-Al₂O₃ particles are fine (∼0.2 μm, i.e., 2.9 × 10¹⁴γ-Al₂O₃ particles/cm³), then they seed the phase transformation. The fine α-Al₂O₃ decreases the transformation temperature to ∼962°C and results in a finer microstructure. The smaller particle size of the seeded RBAO decreases the sintering temperature to as low as ∼1135°C. The results confirm that seeding can be utilized to improve phase transformations and densification and subsequently to tailor final microstructures in RBAO-derived ceramics.     

Influence of Cr and Fe on Formation of α-Al2O3 from γ-Al2O3

The effect of Cr and Fe in solid solution in γ-Al₂O₃ on its rate of conversion to α-Al₂O₃ at 1100°C was studied by X-ray diffraction. The δ form of Al₂O₃ was the principal intermediate phase produced from both pure γ-Al₂O₃ and that containing Fe³⁺ in solid solution, although addition of Fe greatly reduced crystallinity. Reflectance spectra and magnetic susceptibilities showed that Cr exists as Cr⁶⁺ in γ-Al₂O₃ and as Cr³⁺ in α-Al₂O₃, with θ-Al₂O₃ as the intermediate phase. The intermediates formed rapidly, and the rates of their conversion to α-Al₂O₃ were increased by 2 and 5 wt% additions of Fe and decreased by 2 and 4 wt% additions of Cr. An approximately linear relation observed between α-Al₂O₃ formation and decrease in specific surface area was only slightly affected by the added ions. This relation can be explained by a mechanism in which the sintering of δ- or θ-Al₂O₃, within the aggregates of their crystallites, is closely coupled with conversion of cubic to hexagonal close packing of O^2- ions by synchro-shear.     

Interpretation of the Kaolinite-Mullite Reaction Sequence from Infrared Absorption Spectra

The phases in the kaolinite-mullite reaction sequence were reexamined by ir absorption spectrophotometry. Particular attention was paid to the controversial intermediate Al-containing phases. Amorphous materials were leached from fired kaolinite samples with NaOH to help identify crystalline phases. Metakaolinite partially decomposes, releasing amorphous γ-Al₂O₃ and SiO₂, before the "950°C" exothermic reaction in which metakaolinite is completely decomposed. The resulting spinel-type phase, which is associated with amorphous SiO₂ and some poorly crystalline "primary" mullite, is γ-Al₂0₃ (crystalline) rather than an Al-Si spinel. There is some evidence, however, that a fraction of the γ-Al₂O₃, may be an Al-Si spinel. At ≥1100°C secondary mullite therefore forms primarily from the γ-Al₂O₃/amorphous SiO₂ reaction and the recrystallization of primary mullite, whereas excess amorphous SiO₂ eventually crystallizes as cristobalite.     

Synthesis of α-Alumina Hexagonal Platelets Using a Mixture of Boehmite and Potassium Sulfate

Single-crystal α-alumina (Al₂O₃) hexagonal platelets with a diameter of about 200 nm and 25 nm in thickness were synthesized by heating a mixture of boehmite and potassium sulfate at 1000°C for 2 h and washing with water. The potassium sulfate addition effects on the Al₂O₃ phase and morphology were investigated using differential thermal analysis (DTA), X-ray diffraction (XRD), and transmission electron microscopy (TEM). It was found that potassium sulfate addition helps in the formation of single-crystal α-Al₂O₃ hexagonal platelets and promotes phase transformation from intermediate γ-Al₂O₃ to α-Al₂O₃.     

Seeding with γ-Alumina for Transformation and Microstructure Control in Boehmite-Derived α-Alumina

The dehydration, transformation, and densification of boehmite (γ-AlOOH) are enhanced by addition of γ-Al₂O₃ seed particles. α-Al₂O₃ microstructures with uniform 1- to 2-μm grain size and sintered densities 98% of theoretical are achieved at 1300°C Thermal analysis shows that γ-Al₂O₃ seed particles transform to α-Al₂O₃ before the matrix, thus controllably nucleating the transformation of θ-AI₂O₃ to α-Al₂O₃.     

New Sol–Gel Route for the Preparation of Pure α-Alumina at 950°C

An anhydrous alumina (Al₂O₃) sol was prepared from aluminum isopropoxide and an organic solvent, using an acetic acid stabilizer. The complete conversion of the dried sol to α-Al₂O₃ was accomplished at a temperature of 950°C by a single transition via γ-Al₂O₃. Al₂O₃ that was deposited via dip coating resulted in amorphous films, even after annealing at 1100°C, because of the silicon diffusion from the substrate. This phenomenon was avoided using a rapid thermal treatment in a flame after dip coating, which resulted in uniform thin films that are converted to α-Al₂O₃ via heat treatment.     

Auger Electron Spectroscopy of Aluminum Nitride Powder Surfaces

The chemical states of powder surfaces depend on the manufacturing processes of the powders. The surface chemistry of three different commercial AIN powders, which are processed by carbothermal nitridation of Al₂O₃, chemical vapor deposition (CVD), and direct nitridation of aluminum, were evaluated by using Auger electron spectroscopy (AES). In order to obtain reference AES spectra of aluminum compounds, α-, γ-, θ-Al₂O₃, γ-AIOOH, γ-AION, and sintered AIN were also examined. Line shapes of aluminum LVV ; Al( LVV ), nitrogen KLL ; N( KLL ) and oxygen KLL ; O( KLL ) are discussed for the AIN powders and all the other aluminum compounds. The differential Auger electron spectra, i.e., E dn /AE were obtained directly, where n is the number of Auger electrons, and E is the kinetic energy of the electron. Their integrated spectra, i.e., n ( E ) are also employed for analysis. The results confirm the conclusions of our previous temperature-programmed desorption work. The AES line shape analysis implies the presence of an oxide-like θ -Al₂O₃ containing AION phase on the carbothermal nitride AIN powder surfaces. The surfaces of CVD and direct-nitrided AIN powders are covered by an oxide–like γ-Al₂O₃ with an oxygen diffusion layer and does not have AION phase.     

Effect of Monovalent Cation Additives on the γ-Al2O3-to-α-Al2O3 Phase Transition

The effect of monovalent cation addition on the γ-Al₂O₃-to-α-Al₂O₃ phase transition was investigated by differential thermal analysis, powder X-ray diffractometry, and specific-surface-area measurements. The cations Li⁺, Na⁺, Ag⁺, K⁺, Rb⁺, and Cs⁺ were added by an impregnation method, using the appropriate nitrate solution. β-Al₂O₃ was the crystalline aluminate phase that formed by reaction between these additives and Al₂O₃ in the vicinity of the γ-to-α-Al₂O₃ transition temperature, with the exception of Li⁺. The transition temperature increased as the ionic radii of the additive increased. The change in specific surface area of these samples after heat treatment showed a trend similar to that of the phase-transition temperature. Thus, Cs⁺ was concluded to be the most effective of the present monovalent additives for enhancing the thermal stability of γ-Al₂O₃. Because the order of the phase-transition temperature coincided with that of the formation temperature of β-Al₂O₃ in these samples, suppression of ionic diffusion in γ-Al₂O₃ by the amorphous phase containing the added cations must have played an important role in retarding the transition to α-Al₂O₃. Larger cations suppressed the diffusion reaction more effectively.     

Microwave Plasma Synthesis of Nanostructured γ-Al2O3 Powders

Nanostructured Al₂O₃ powders have been synthesized by combustion of aluminum powder in a microwave oxygen plasma, and characterized by X-ray diffraction and electron microscopy. The main phase is γ-Al₂O₃, with a small amount of δ-Al₂O₃. The particles are truncated octahedral in shape, with mean particle sizes of 21–24 nm. The effect of reaction chamber pressure on the phase composition and the particle size was studied. The γ-alumina content increases and the mean particle size decreases with decreasing pressure. No α-Al₂O₃ appears in the final particles. Electron microscopy studies find that a particle may contain more than one phase.     

Fabrication of Nano-Scaled α-Al2O3 Crystallites Through Heterogeneous Precipitation of Boehmite in a Well-Dispersed θ-Al2O3-Suspension

The possibility of eliminating finger or vermicular growth of α-Al₂O₃ particles obtained by calcination of boehmite was examined. Heterogeneous precipitation of boehmite in a well-dispersed θ-Al₂O₃ suspension was first prepared, in which the mass ratio of boehmite to θ-crystallite was evaluated to form agglomerates of similar sizes that will form α-Al₂O₃ crystallites of <100 nm in diameter. θ- to α-phase transformation of alumina experiences a nucleation and growth mechanism, with the critical size of nucleation being ∼25 nm for θ-Al₂O₃ and the size for accomplishment of transformation followed by finger growth being ∼100 nm. Hence, fabricating agglomerates that would form α-Al₂O₃ crystallites with sizes <100 nm accompanied with appropriate thermal treatments can be a method for obtaining α-Al₂O₃ crystallites free of finger growth. It is found that proper preparation of the agglomerate with appropriate size may initiate a simultaneous and lower temperature θ- to α-Al₂O₃ phase transformation for such powder systems, substantially limiting the mass transfer among the newly formed α-Al₂O₃ particles. Moreover, α-Al₂O₃ crystallites free of finger growth can be obtained.     

Mechanical-Activation-Triggered Gibbsite-to-Boehmite Transition and Activation-Derived Alumina Powders

Mechanical activation of monoclinic gibbsite (Al(OH)₃) in nitrogen led to the formation of nanocrystalline orthorhombic boehmite (AlOOH) at room temperature. The boehmite phase formed after merely 3 h of mechanical activation and developed steadily as the mechanical-activation time increased. Forty hours of mechanical activation resulted in essentially single-phase boehmite, together with α-alumina (α-Al₂O₃) nanocrystallites 2–3 nm in size. The sequence of phase transitions in the activation-derived boehmite was as follows: boehmite to γ-Al₂O₃ and then to α-Al₂O₃ when flash-calcined at a heating rate of 10°C/min in air. γ-Al₂O₃ formed at 520°C, and flash calcination to 1100°C led to the formation of an α-Al₂O₃ phase, which exhibited a refined particle size in the range of 100–200 nm. In contrast, the gibbsite-to-boehmite transition in the unactivated gibbsite occurred over the temperature range of 220°–330°C. A flash-calcination temperature of 1400°C was required to complete the conversion to α-Al₂O₃ phase, with both δ-Al₂O₃ and θ-Al₂O₃ as the transitional phases. The resulting alumina powder consisted of irregularly shaped particles 0.4–0.8 μm in size, together with an extensive degree of particle agglomeration.     

Crystallization Behavior of Al2O3 in the Presence or SiO2

The independent crystallization sequence of an Al₂O₃ component is modified in the presence of SiO₂ and vice versa. Mixed SiO₂-Al₂O₃, gel (28 wt% SiO₂ and 72 wt% Al₂O₃) forms neither cristobalite nor γ-Al₂O₃ and corundum at 1000°C but forms Si-Al spinel; an amorphous aluminosilicate phase invariably also forms after the gel is heated. However, the composition of this amorphous aluminosilicate phase is not as yet known.     

Carbothermal Synthesis of Aluminum Nitride Using Sucrose

Several aluminum oxides (α-Al₂O₃, θ-Al₂O₃, and AIOOH) were examined to study the differences in reaction behavior and powder characteristics during carbothermal nitrida-tion to AIN using sucrose and carbon black. The reaction conditions investigated were carbon-to-alumina ratio, reaction temperature, and time. Carburized sucrose resulted in Full conversion to AIN and produced a uniform powder morphology using a near-istoichiometric ratio of C:Al₂O₃ while carbon black required higher C:Al₂O₃ ratios (i.e., >4:1) for full conversion and led to agglomeration of the AIN powder. The most favorable reaction temperature was 1600°C, with the reaction time to full conversion being dependent on the type of Al₂O₃. The particle and agglomerate size of the AIN powders did not change significantly with reaction time. However, the particle size and morphology were strongly dependent on that of the initial AI₂O₃ with sucrose, whereas agglomeration of the AIN occurs when using carbon black. A solid–solid reaction mechanism is proposed.