A 10-bit 200-MHz CMOS video DAC for HDTV applications

This paper describes a 10-bit 200-MHz CMOS current steering digital-to-analog converter (DAC) for HDTV applications. The proposed 10-bit DAC is composed of a unit decoded matrix for 6 MSBs and a binary weighted array for 4 LSB’s, considering linearity, power consumption, routing area, and glitch energy. A new switching scheme for the unit decoded matrix is developed to improve linearity further. Cascade current sources and differential switches with deglitch latch improve dynamic performance. The measured differential nonlinearity (DNL) and integral nonlinearity (INL) are 0.3 LSB and 0.2 LSB, respectively. The converter achieves a spurious-free dynamic range (SFDR) of above 55 dB over a100-MHz bandwidth and low glitch energy of 1.5 pVs. The circuit is fabricated in a 0.25 μm CMOS process and occupies 0.91 mm². When operating at 200 M Sample/s, it dissipates 82 mW from a 3.3 V power supply.     

A self-trimming 14-b 100-MS/s CMOS DAC

A 14-b 100-MS/s CMOS digital-analog converter (DAC) designed for high static and dynamic linearity is presented. The DAC is based on a central core of 15 thermometer decoded MSBs, 31 thermometer decoded upper LSBs (ULSBs) and 31 binary decoded lower LSBs (LLSBs). The static linearity corresponding to the 14-b specification is obtained by means of a true background self-trimming circuit which does not use additional current sources to replace the current source being measured during self-trimming. The dynamic linearity of the DAC is enhanced by a special track/attenuate output stage at the DAC output which tracks the DAC current outputs when they have settled but attenuates them for a half-clock cycle after the switching instant. The DAC occupies 3.44 mm×3.44 mm in a 0.35-μm CMOS process, and is functional at up to 200 MS/s, with best dynamic performance obtained at 100 MS/s. At 100 MS/s, power consumption is 180 mW from a 3.3-V power supply, and 210 mW at 200 MS/s     

12位300MHz电流驱动型DAC

在电路误差、电路占用芯片面积相互折中和妥协的前提下提出了一种8+4结构的电流驱动型数模转换器.采用Q2 random walk方法设计了一个新型的双中心对称的电流矩阵,确保数模转换器的线性度.分析并求出了最佳电平交叉点,设计了电平钳位锁存器对开关电平限幅,DAC动态性能得到改善.在12位分辨率下,刷新率达到300MHz以上.     

A 12bit 300MHz Current-Steering CMOS D/A Converter

The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs,trading-off between the precision,speed,and size of the chip.In order to ensure the linearity of the DAC,a double Centro symmetric current matrix is designed by the Q2 random walk strategy.To achieve better dynamic performance,a latch is added in front of the current switch to change the input signal,such as its optimal crosspoint and voltage level.For a 12bit resolution,the converter reaches an update rate of 300MHz.     

面向高速应用的10位2GHz数模转换器

提出了一个刷新率达2GHz的10位电流驱动型数模转换器.在综合了精度与芯片面积等因素之后,该数模转换器使用6 4结构.采用电流型逻辑以提高转换器的速度,并采用Q2 random walk方法设计了一个双中心对称的电流矩阵,确保数模转换器的线性度.该数模转换器核心版图面积为2.2mm×2.2mm,在3.3V单电压供电的情况下,该芯片功耗为790mW.     

面向高速应用的10位2GHz数模转换器

提出了一个刷新率达2GHz的10位电流驱动型数模转换器.在综合了精度与芯片面积等因素之后,该数模转换器使用6+4结构.采用电流型逻辑以提高转换器的速度,并采用Q2 random walk方法设计了一个双中心对称的电流矩阵,确保数模转换器的线性度.该数模转换器核心版图面积为2.2mm×2.2mm,在3.3V单电压供电的情况下,该芯片功耗为790mW.     

An untrimmed D/A converter with 14-bit resolution

Describes a monolithic 14-bit DAC which uses a new compensation technique for the DAC linearity, the `self-compensation technique', originated through a new concept. Since this technique automatically compensates for linearity error in the DAC by referring to a ramp function with about 17-bit linearity, a high precision DAC can be produced in monolithic form without the trimming of analog components. An experimental 14-bit DAC chip has been fabricated using analog compatible IIL technology and two-level metalization. A linearity error of less that /spl plusmn/1/2 LSB and a settling time of 1-2 /spl mu/s has been achieved.     

A 10-b 125-MHz CMOS digital-to-analog converter (DAC) withthreshold-voltage compensated current sources

This paper describes a 10-b high-speed COMS DAC fabricated by 0.8-μm double-poly double-metal CMOS technology. In the DAC, a new current source called the threshold-voltage compensated current source is used in the two-stage current array to reduce the linearity error caused by inevitable current variations of the current sources. In the two-stage weighted current array, only 32 master and 32 slave unit current sources are required. Thus silicon area and stray capacitance can be reduced significantly. Experimental results show that a conversion rate of 125 MHz is achievable with differential and integral linearity errors of 0.21 LSB and 0.23 LSB, respectively. The power consumption is 150 mW for a single 5-V power supply. The rise/fall time is 3 ns and the full-scale settling time to ±1/2 LSB is within 8 ns. The chip area is 1.8 mm×1.0 mm     

分段式电流舵 D/A转换器抗di/dt噪声设计

设计了一个8位50MHzD/A转换器(DAC),采用5+3分段式电流舵差分输出结构,其中高5位采用温度计码方式译码,低3位采用二进制译码方式;从各电路模块设计结构上提高DAC抗di/dt噪声的能力;设计了一个低交叉点开关驱动电路,有效地降低了输出毛刺,减小了数字电路di/dt噪声的影响。采用VIS0.35μmCMOS工艺进行仿真,结果表明,微分非线性(DNL)和积分非线性(INL)均小于0.15LSB。     

一种GSM无线发射系统中的低功耗数模转换器

针对GSM标准无线发射系统中数模转换器(DAC)的要求,分析了影响其性能和功耗的限制因素,并在SMIC 0·13μm CMOS工艺1.2 V电源电压下设计了一款10位电流驱动型数模转换器(Current-steering DAC).使用最佳拟合线的算法衡量电流源匹配的随机误差对DAC静态非线性的影响,使得DAC的电流源...     

A 10 bit 1 GSPS Nyquist DAC in 180 nm CMOS with high FOM

A new segmented architecture is presented to improve the dynamic and static performance of the current steering digital-to-analog converters (DACs). In the proposed architecture instead of a single binary DAC, distributed binary cells are used. So the effect of the mismatch and timing errors of the binary cells are not accumulated and are averaged out. For realization of the MSB unit cells those binary cells are reused to form the larger weighted unit cells. Realization of the MSB unit cells with smaller cells results in improved dynamic performances as the effects of gradient errors are minimized and the effects of nonlinear parasitic capacitances are reduced. The DAC has been designed in 180 nm five-metal nwell CMOS process. The simulation results show that the DAC can achieve a maximum spurious free dynamic range (SFDR) of 70.99 dB at 2.93 MHz signal for a sampling rate of 1 GSPS considering the mismatch effects. For 1 GSPS sampling rate the simulated Nyquist SFDR is >70 dB with mismatch. The simulated third order intermodulation distortion (IM3) of the DAC with mismatch effect is 71.40 dB, for a dual tone test with 491.21 and 495.12 MHz signals. The DAC is optimized for digital signal synthesis applications in wireless base stations and other communication applications. The power dissipation of the DAC is 78.21 mW at 498.05 MHz signal for a sampling rate of 1 GSPS with 1.8 V supply.     

Optimum selection of capacitive array for multibit Sigma-Delta modulators without DEM

A method for a smart selection and sequencing of unity capacitors in a multibit digital-to-analog converter (DAC) that improves the linearity is proposed. The approach, suitable for the DAC nonlinearity correction in Sigma-Delta modulators, obtains better results than dynamic element matching. The key of the proposed technique is an off-line self-measurement of mismatches with the available hardware. The results significantly improve when redundant DAC capacitors are introduced. Hence, the capacitors are selected from a set that is larger than required. An affordable silicon area overhead introduced by the redundant capacitors avoids extra power consumption, that is unavoidable in other methods during the normal operation of the converter.     

A high-performance CMOS 70-MHz palette/DAC

A VLSI circuit has been developed that combines dual-ported RAMs and three high-speed 8-b digital-to-analog converters (DACs). It is known as a palette/DAC. A 6-2 segmented DAC architecture improves differential linearity and monotonicity. The current-source cell uses a cascode device to improve the DAC's linearity. A reference current, set by an on-chip bandgap reference voltage generator, and its associated distribution scheme eliminate the negative effects of threshold mismatches between current source cells, supply line resistance, and noise. The maximum conversion rate is 70 MHz with typical DC differential nonlinearity of 0.48 LSB (least significant bit). The 253-mil/SUP 2/ is designed on a double-metal CMOS process and consumes 1.2 W of power.     

A 12-bit 1-Gword/s GaAs digital-to-analog converter system

The circuitry for a 12-b 1-Gword/s digital-to-analog converter (DAC) IC is described. A DC linearity of /spl plusmn/1/8 LSB has been preserved with this all-depletion GaAs MESFET chip. Dynamic measurements in the frequency domain indicate nonlinearities of less than -62 dBc at a 1-GHz clock rate. The DAC uses a very fast FET analog current switch that exhibits sufficiently low leakage currents for a 12-b linearity. The limited on-chip matching capabilities require the precision DC currents to be generated external to the GaAs chip. A current-switching DAC that partitions the high-speed functions onto a single GaAs chip while the high-precision bit currents are realized off-chip is described. The GaAs chip contains 12 1-b cells, each of which switches an analog bit current into a single sampler circuit that is shared by all the switches. The sampler is used to increase the dynamic linearity in the DAC.     

Design considerations of calibration DAC in self-calibrated SAR A/D converters

A capacitive calibration digital-to-analog converter (CDAC) is commonly used to reduce the mismatch-induced linearity errors for successive approximation register (SAR) analog-to-digital converters (ADC) employing capacitor arrays. There are complicated design considerations in determining the number of bits, the unit capacitor value and even the parasitic capacitors of the CDAC, as these factors affect or are determined by the achievable ADC resolution, the main DAC's capacitance, and the main DAC unit capacitance value, etc. This paper is the first to present a systematic analysis on these relationships. The analysis is validated by behavioral and circuit simulation results.     

A complete high-speed voltage output 16-bit monolithic DAC

A new single-chip 16-bit monolithic digital/analog converter (DAC) with on-chip voltage reference and operational amplifiers has achieved /spl plusmn/0.0015% linearity, 10 ppm//spl deg/C gain drift, and 4-/spl mu/s settling time. Novel elements of the 16-bit DAC include: the fast settling open-loop reference with a buried Zener, a fast-settling output operational amplifier without the use of feedforward compensation, and a modified R-2R ladder network. Thermal considerations played a significant role in the design. The DAC is fabricated using a 20-V process to reduce device sizes and therefore die size. All laser trimming including temperature drift compensation is performed at the wafer level. The converter does not require external components for operation.     

Efficient, ROM-less DDFS using non-linear interpolation and non-linear DAC

A non-linear interpolation based ROM-less Direct Digital Frequency Synthesisiser (DDFS) is more efficient than previous systems as each current cell in a non-linear DAC is used more effectively. This was achieved by forming an analogue voltage from a small linear DAC addressed by phase bits that are usually discarded. The analogue voltage was connected to a selected current source in a thermometer decoded non-linear DAC to allow non-linear interpolation between the conventional, phase limited output levels. By increasing the number of phase bits the spurious free dynamic range (SFDR) was improved without increasing the size of the non-linear DAC. Modelling and simulation of the non-linear response of the differential switch based current cell revealed suitable parameters. The architecture of 64 current cells used a modified thermometer decoder and three-state switch in each current cell. Simulation and testing of 10 sample circuits demonstrated a robust DDFS with SFDR better than −60 dBc and suitable for use in a wide range of instrumentation systems.     

一种带电流源校准的16bit高性能DAC

设计了一种带电流源校准电路的16 bit高速、高分辨率分段电流舵型数模转换器(DAC)。针对电流舵DAC中传统差分开关的缺点,提出了一种优化的四相开关结构。系统分析了输出电流、积分非线性和无杂散动态范围(SFDR)三个重要性能指标对电流舵DAC的电流源单元设计的影响,完成了电流源单元结构和MOS管尺寸的设计。增加了一种优化设计的电流源校准电路以提高DAC的动态性能。基于0.18μm CMOS工艺完成了该DAC的版图设计和工艺加工,其核心部分芯片面积为2.8 mm^2。测试结果表明,在500 MHz采样速率、100 MHz输入信号频率下,测得该DAC的SFDR和三阶互调失真分别约为76和78 dB,动态性能得到明显提升。     

Linearity enhancements for pipeline digital to analogue converters

A high-speed/high-linearity pipeline switched capacitor digital to analogue converter (DAC) is presented. This DAC yields better linearity compared to previously published implementations, owing to a number of circuit techniques that are discussed     

Design and analysis of high speed capacitive pipeline DACs

Design of a high speed capacitive digital-to-analog converter (SC DAC) is presented for 65 nm CMOS technology. SC pipeline architecture is used followed by an output driver. For GHz frequency operation with output voltage swing suitable for wireless applications (300 mV_pp) the DAC performance is shown to be limited by the clock feed-through and settling effects in the SC array rather than by the capacitor mismatch or kT/C noise, which appear negligible in this application. While it is possible to design a highly linear output driver with HD3 < ?70 dB and HD2 < ?90 dB over 0.5–5 GHz band as we show, the maximum SFDR of the SC DAC is 45 dB with 8-bit resolution and Nyquist sampling of 3 GHz. The capacitor array is designed based on the DAC design area defined in terms of the switch size and unit capacitance value. A tradeoff between the DAC bandwidth and resolution accompanied by SFDR is demonstrated. High linearity of the output driver is attained by a combination of two techniques, the derivative superposition (DS) and resistive source degeneration. In simulations the complete DAC achieves SFDR of 45 dB with 8-bit resolution for signal bandwidth 1.36 GHz with Nyquist sampling. With 6-bit and 5.5 GHz bandwidth 33 dB SFDR is attained. The total power consumption of the SC DAC is 90 mW with 1.2 V supply and clock frequency of 3 GHz.