Synthesis of ZnNb2O6 powder with rod-like particle morphologies

A ZnNb₂O₆ powder was synthesized through the molten salt method. The XRD and SEM results indicated that the crystal ZnNb₂O₆ powder with rod-like particle morphologies could be obtained via this method at temperature of 600 °C, which is significantly lower than that required by solid-state reaction, where a calcining temperature of 800 °C was needed and the obtained ZnNb₂O₆ particles were equiaxial. The heat treatment temperature scarcely affected the ZnNb₂O₆ particle morphologies in the molten salt synthesis process.     

Low-temperature synthesis of BiNbO4 ceramics using reaction-sintering process

Low-temperature synthesis of BiNbO₄ ceramics using reaction-sintering process was investigated. Orthorhombic BiNbO₄ phase together with minor triclinic BiNbO₄ phase were found in the pellets. The phase transition temperature in BiNbO₄ with 0.5 wt% CuO addition was lowered from 960 °C via traditional route to 880 °C when the reaction-sintering process was used. After 920 °C sintering for 4 and 6 h, densities 6.8–6.85 g/cm³ (94% of the theoretical value) were obtained. The abnormal grain growth in BiNbO₄ via traditional route was not observed in this study.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Synthesis of Zn3Nb2O8 ceramics using a simple and effective process

Synthesis of Zn₃Nb₂O₈ ceramics using a simple and effective reaction-sintering process was investigated. The mixture of ZnO and Nb₂O₅ was pressed and sintered directly without any prior calcination. Single-phase Zn₃Nb₂O₈ ceramics could be obtained. Density of these ceramics increased with soaking time and sintering temperature. A maximum density 5.72 g/cm³ (99.7% of the theoretical density) was found for pellets sintered at 1170 °C for 2 h. Pores were not found and grain sizes >20 μm were observed in pellets sintered at 1170 °C. Abnormal grain growth occurred and grains >50 μm could be seen in Zn₃Nb₂O₈ ceramics sintered at 1200 °C for 2 h and 1200 °C for 4 h. Reaction-sintering process is then a simple and effective method to produce Zn₃Nb₂O₈ ceramics for applications in microwave dielectric resonators.     

Synthesis and properties of (BaxPb1−x)(Zn1/3Nb2/3)O3 relaxor ferroelectric ceramics using a reaction-sintering process

(Ba_xPb_1−x)(Zn_1/3Nb_2/3)O₃ (BPZN; x = 0.06–0.1) relaxor ferroelectric ceramics produced using a reaction-sintering process were investigated. Without any calcination involved, the mixture of raw materials was pressed and sintered directly. BPZN ceramics of 100% perovskite phase were obtained. Highly dense BPZN ceramics with a density higher than 98.5% of theoretical density could be obtained. Maximum dielectric constant K_max 13,500 (at 75 °C), 19,600 (at 50 °C) and 14,800 (at 28 °C) at 1 kHz could be obtained in 6BPZN, 8BPZN and 10BPZN, respectively. Dielectric maximum temperature (T_max) in BPZN ceramics via reaction-sintering process is lower than BPZN ceramics prepared via B-site precursor route.     

Preparation of nanocrystalline Sr3Al2O6 powders via citric acid precursor

Sr₃Al₂O₆ was synthesized via citric acid precursor. The effects of the molar ratio of citric acid to total metal cations concentration (CA/M) on the formation of Sr₃Al₂O₆ were investigated. Increasing the CA/M promoted the formation of Sr₃Al₂O₆. Single-phase and well-crystallized Sr₃Al₂O₆ was obtained from the CA/M = 1, CA/M = 2 and CA/M = 4 precursor at temperature 1200 °C, 1100 °C and 900 °C, respectively. Differential thermal analysis and thermogravimetric (DTA/TG), X-ray diffractometry (XRD) and field emission scanning electron microscopy (FESEM) were used to characterize the precursors and the derived oxide powders. Sr₃Al₂O₆ nanoparticles with a diameter of about 50-70 nm were obtained.     

Mechanochemical synthesis and characterisation of BaTa2O6 ceramic powders

Mechanochemical synthesis was used to prepare BaTa₂O₆ powders from BaCO₃ and Ta₂O₅ precursors in a planetary ball mill. Effect of milling time and heat treatment temperature on the formation of BaTa₂O₆ and on the microstructure was investigated. Intensive milling of starting materials resulted in crystallization of BaTa₂O₆ even after 1 h of milling time and single phase BaTa₂O₆ was obtained after 10 h of milling under optimal conditions. The powder derived from 10 h of mechanical activation had crystallite size of 22 nm. But the increase in milling time did not decrease the crystallite size further. High energy milling activated the powders that although 1 h of milling led to formation of single phase BaTa₂O₆ at 1200 °C, this temperature decreased to 900 °C after 5 h of milling. No significant grain growth was observed when the milled powders were heat treated below 900 °C. However, annealing at 1100 and 1200 °C gave an average BaTa₂O₆ grain size of 180 and 650 nm, respectively. An unidentified phase started to form at 1100 °C increasing to high amounts at 1200 °C and they had different shapes and sizes than BaTa₂O₆ grains. These elongated large grains were thought to be due to liquid phase formation caused by iron contamination.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Mechanochemical synthesis of MgTa2O6 ceramic

MgTa₂O₆ powders were prepared by mechanochemical synthesis from MgO and Ta₂O₅ in a planetary ball mill in air atmosphere using steel vial and steel balls. High-energy ball milling gave nearly single-phase MgTa₂O₆ after 8 h of milling time. Annealing of high-energy milled powder at various temperatures (700–1200 °C) indicated that high-energy milling speed up the formation and crystallization of MgTa₂O₆ from the amorphous mixture. The powder derived from 8 h of mechanical activation gave a particle size of around 28 nm. Although at low-annealing temperatures the grain size was almost the same as-milled powder, the grain size increased with annealing temperature reaching to around 1–2 μm after annealing at 1200 °C for 8 h.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Preparation of ZrO2/Gd2O3 composite ceramic materials by coprecipitation method

High burnup is a goal for further development of advanced nuclear power in the future. However, along with the increase of burnup, it becomes more diffidult to control reactor reactivity, which affects the operation safety of the nuclear reactor. Al₂O₃/B₄C burnable poison materials widely used in pressurized water reactor currently will not meet the requirements of burnable poison materials in high burnup nuclear power. Because of the better performance of ZrO₂/Gd₂O₃ burnable poison materials than that of Al₂O₃/B₄C, this paper studies the preparation of ZrO₂/Gd₂O₃ composite ceramic materials by the coprecipitation method. The experimental results show that at the sintering temperature of 1500–1650 °C, ZrO₂/Gd₂O₃ composite ceramic grains are small, compact and uniform with the generation of homogeneous solid solution. At 1600 °C, ZrO₂–10%Gd₂O₃ has the highest density and mechanical strength.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Matrix–filler interactions in polysilazane-derived ceramics with Al2O3 and ZrO2 fillers

Interactions between a poly(vinyl)silazane and Al₂O₃ or Y₂O₃-stabilised ZrO₂ fillers were studied during the fabrication of polysilazane-derived bulk ceramics in order to investigate the influence of oxide fillers on resulting properties. Specimens were produced by coating of the filler powders with the polysilazane, warm-pressing of the resulting composite powders, and pyrolytic conversion in flowing N₂ at various temperatures between 1000 °C and 1400 °C. Significant differences in densification were observed, depending on the filler used. Reactions between the polysilazane-derived matrix and Al₂O₃ or ZrO₂ at temperatures ≥1300 °C resulted in the formation of Si₅AlON₇ or ZrSiO₄, respectively. Reactivity in the polysilazane-derived component was a result of SiO₂ contamination caused primarily by adsorbed species on the filler particle surface. Knowledge of polysilazane/filler interface processes is found to be decisive for the prediction of properties such as shrinkage and porosity, which heavily influence performance of a material.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Long-term degradation of Ta2O5-doped Bi2O3 systems

Bismuth oxide in δ-phase is a well-known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). 5-10 mol% Ta₂O₅ are doped into Bi₂O₃ to stabilize δ-phase by solid state reaction process. One Bi₂O₃ sample (7.5TSB) was stabilized by 7.5 mol% Ta₂O₅ and exhibited single phase δ-Bi₂O₃-like (type I) phase. Thermo-mechanical analyzer (TMA), X-ray diffractometry (XRD), AC impedance and high-resolution transmission electron microscopy (HRTEM) were used to characterize the properties. The results showed that holding at 800-850 °C for 1 h was the appropriate sintering conditions to get dense samples. Obvious conductivity degradation phenomenon was obtained by 1000 h long-term treatment at 650 °C due to the formation of α-Bi₂O₃ phase and Bi₃TaO₇, and 〈1 1 1〉 vacancy ordering in Bi₃TaO₇ structure.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part II: Microstructural study

In this work results on dynamic corrosion studies of fused cast Al₂O₃-SiO₂-ZrO₂ and isostatically pressed and sintered Cr₂O₃-based refractories by two crystalline (transparent) frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C.Microstructural and mineralogical analyses of selected areas from the corroded regions of the studied refractories were performed by reflected light optical microscopy and scanning electron microscopy with analysis by X-ray dispersive energy.Significant differences between the corrosion mechanisms acting in the two types of materials were found. In the fused cast Al₂O₃-SiO₂-ZrO₂ specimens corrosion took place by the dissolution of alumina and zirconia in the frit and in the glass formed by the reaction between the frit and the refractory. In the Cr₂O₃-based materials the corrosion process was controlled by the capillar penetration of the molten frit through the open pores. The reaction between the ZnO from the frits and Cr₂O₃ led to the formation of spinel (ZnCr₂O₄), a high-melting point bonding phase that retarded the frit penetration. Results are discussed using the relevant phase equilibrium diagrams.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.