Microstructure and magnetic properties of Ni0·75Zn0·25Fe2O4 ferrite prepared using an electric current-assisted sintering method

Using a Ni_0·75Zn_0·25Fe₂O₄ nanopowder synthesized by means of a hydrothermal method as a raw material, polycrystalline nickel zinc (NiZn) ferrite ceramics composed of sub-micron grains were successfully prepared via an electric current-assisted sintering method. Temperatures ranging from 800 °C to 950 °C and a dwell time of 20 min were employed. The phase composition and microstructure of the samples were characterized via X-ray diffraction and scanning electron microscopy, respectively. Moreover, the magnetic properties of the samples were investigated using a vibrating sample magnetometer and a ferromagnetic resonance system. The results revealed that each sintered sample was mainly composed of a spinel phase. With increasing sintering temperature, the specific saturation magnetization increased from 71.85 emu/g to 74.58 emu/g, owing mainly to the increase in the relative density and the average grain size of the NiZn ferrites. The coercivity and ferromagnetic resonance linewidth of the ferrite ceramics decreased monotonically with increasing sintering temperature, owing mainly to the magnetostriction coefficient, saturation magnetization, and porosity of the sintered ferrites.     

Characterization of submicrometer-sized NiZn ferrite prepared by spark plasma sintering

High-density submicrometer-sized Ni_0.5Zn_0.5Fe₂O₄ ferrite ceramics were prepared by spark plasma sintering in conjunction with sufficient high energy ball milling. They were evaluated by different characterization techniques such as X-ray diffraction, scanning electron microscopy, and dielectric and magnetic measurements. All samples prepared at sintering temperatures ranging from 850 to 925 °C exhibit a single spinel phase and their relative densities and grain sizes range from 90% to 99% and ~100 nm to ~300 nm, respectively. The dielectric constant increases with decreasing grain size until ~250 nm, and then decreases dramatically with further decreasing grain size. The saturation magnetization increases continuously with increasing grain size/density but the magnetic coercivity decreases. The highest dielectric constant and saturation magnetization at room temperature are approximately 1.0×10⁵ and 84.4 emu/g, respectively, while the lowest magnetic coercivity is only around 15 Oe. These outstanding properties may be associated with high density and uniform microstructure created by spark plasma sintering. Therefore, the spark plasma sintering is a promising technique for fabricating high-quality NiZn ferrites with high saturation magnetization and low coercivity.     

Synthesis and characterizations of Ni0.8Zn0.2Fe2O4-MWCNTs composites for their application in sea bed logging

Sea bed logging is new technique for the detection of hydrocarbon reservoir. Magnitude of EM waves is important for the detection of deep target hydrocarbon reservoir below 4000 m from the sea floor. A new aluminium based EM transmitter is developed and NiZn (Ni_0.8Zn_0.2Fe₂O₄) ferrite with and with out multiwall carbon nano tubes (MWCNTs) polymer composites as magnetic feeders are used in a scaled tank. Nickel zinc ferrite plays an important role in many applications due to its best magnetic properties. Nanocrystalline NiZn (Ni_0.8Zn_0.2Fe₂O₄) ferrite and novel Ni_0.8Zn_0.2Fe₂O₄-MWCNTs composites were prepared by sol-gel route. The samples were sintered at 750-950 °C and were characterized by XRD, FESEM, HRTEM and Raman spectroscopy. Single phase of Ni_0.8Zn_0.2Fe₂O₄ having [3 1 1] major peak was obtained by sol-gel method at 750 °C and 950 °C. FESEM micrographs show that grain size increases with the increase of sintering temperature and ranges from 24 to 60 nm. FESEM and HRTEM results showed coating of Ni_0.8Zn_0.2Fe₂O₄ on MWCNTs and show better morphology at the sintering temperature of 750 °C. The magnetic properties measured from impedance vector network analyzer showed that sample (Ni_0.8Zn_0.2Fe₂O₄-MWCNTs) sintered at 750 °C have higher initial permeability (20.043), Q-factor (50.047), and low loss factor (0.0001) as compared Ni_0.8Zn_0.2Fe₂O₄-MWCNTs sintered at 950 °C. Due to better magnetic properties, Sample (Ni_0.8Zn_0.2Fe₂O₄-MWCNTs sintered at 750 °C) composites were used as magnetic feeders for the EM transmitter. It was found that magnitude of EM waves from EM transmitter increased up to 243% by using Ni_0.8Zn_0.2Fe₂O₄-MWCNTs polymer composites.     

Effect of holmium on the magnetic and electrical properties of barium based W-type hexagonal ferrites

A series of BaHo_xFe_16−xO₂₇ (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) W-type hexagonal ferrites were prepared by co-precipitation technique at high annealing temperature of 1320 °C. XRD reveals single W-type hexagonal phase in these ferrites. The grain size is measured by SEM analysis using line intercept method. Saturation magnetization, retentivity and coercivity were measured from MH-loops taken on VSM. It was observed that magnetization increases with the increase of Ho content due to difference in ionic radii of Ho³⁺ (0.901 Å) and Fe³⁺ (0.67 Å) ions. Room temperature dc resistivity increases as a function of Ho³⁺ that may be due to separation between grains. The dc electrical resistivity decreases as a function of temperature which indicates the semi-conducting behavior of the samples.     

Transparent polycrystalline MgAl2O4 ceramic fabricated by spark plasma sintering: Microwave dielectric and optical properties

The optical properties and microwave dielectric properties of transparent polycrystalline MgAl₂O₄ ceramics sintered by spark plasma sintering (SPS) through homemade nanosized MgAl₂O₄ powders at temperatures between 1250 °C and 1375 °C are discussed. The results indicate that, with increasing sintering temperatures, grain growth and densification occurred up to 1275 °C, and above 1350 °C, rapid grain and pore growth occurred. The in-line light transmission increases with the densification and decreases with the grain/pore growth, which can be as high as 70% at the wavelength of 550 nm and 82% at the wavelength of 2000 nm, respectively. As the sintering temperature increases, Q×f and dielectric constant ε_r values increase to maximum and then decrease respectively, while τ_f value is almost independent of the sintering temperatures and remains between −77 and −71 ppm/°C. The optimal microwave dielectric properties (ε_r=8.38, Q×f=54,000 GHz and τ_f=−74 ppm/°C) are achieved for transparent MgAl₂O₄ ceramics produced by spark plasma sintering at 1325 °C for 20 min.     

New NiFe2−xCrxO4 spinel films for O2 evolution in alkaline solutions

Spinel-type ternary ferrites with composition NiFe_2−xCr_xO₄ (0 ≤ x ≤ 1) were synthesized by a precipitation method and their physicochemical and electrocatalytic properties have been investigated using IR, XRD, BET surface area, XPS, impedance and Tafel polarization techniques. The study indicated that substitution of Cr from 0.2 to 1.0 mol in the spinel matrix increased the apparent electrocatalytic activity of the base oxide towards the O₂ evolution reaction in 1 M KOH at 25 °C. The apparent electrocatalytic activity of the oxide with 0.8-1.0 mol Cr was found to be the greatest among the present series of oxides investigated. It is noteworthy that the electrocatalytic activity of the oxide with x = 0.8-1.0 was also greater than those of other spinel/perovskite O₂ evolving electrocatalysts reported in literature.     

Effect of oxygen deficiency reduction in Mg-doped Mn-spinel on its cell storage performance at high temperature

The effect of doping foreign metal ions into the LiMn₂O₄ spinel structure on the oxygen deficiency by high-temperature firing has been investigated. The degree of the oxygen deficiency in the Mg- and/or Al-doped spinel is very small even when fired at 1000 °C, and then the oxygen deficiency nearly disappeared after low temperature annealing. Mg-doped Mn-spinels (Li_1.05Mn_1.94−xMg_xCa_0.01O_4−z, 0 ≤ x ≤ 0.15) obtained at 1000 °C contained a small oxygen deficiency amount when the x-value reached 0.03 or more. The annealing at 800 °C then reduced the oxygen defect content in the Mg-doped spinels. The crystallinity of the spinels is improved by doping with a small amount of Ti. The storage performance of the coin-type cell at 60 °C is improved about 1.6 times using both Mg- and Ti-doping, which would be due to the oxygen stoichiometric spinels with a low solubility by firing at high temperatures and/or by Ti-doping to increase the crystallinity.     

On the spinel formation in Co1 − xO/Co2TiO4 composites via reactive sintering, exsolution and oxidation

The formation mechanism and microstructural development of the spinel phases in the Co_1 − xO/Co₂TiO₄ composites upon reactive sintering the Co_1 − xO and TiO₂ powders (9:1 molar ratio) at 1450 °C and during subsequent cooling in air were studied by X-ray diffraction and analytical electron microscopy. The Co₂TiO₄ spinel occurred as inter- and intragranular particles in the matrix of Ti-doped Co_1 − xO grains with a rock salt-type structure during reactive sintering. The submicron sized Co₂TiO₄ particles were able to detach from grain boundaries in order to reach an energetically favorable parallel orientation with respect to the host Co_1 − xO grains via a Brownian-type rotation/coalescence process. Upon cooling in air, secondary Co₂TiO₄ nanoparticles were precipitated and the Ti-doped Co_1 − xO host was partially oxidized as Co_3 − δO₄ spinel by rapid diffusion along the {1 1 1} and {1 0 0}-decorated interphase interface and the free surface of the composites.     

Electrical properties of samaria-doped ceria electrolytes from highly active powders

The correlations of the microstructures and the electrical properties of high reactive Ce_0.8Sm_0.2O_1.9 (SDC) powders, synthesized via an optimal carbonate coprecipitation method, were investigated. Microstructure of the SDC ceramics sintered at 900-1400 °C showed uniform grain and small grain size, compared with those prepared with various methods under similar sintering conditions. These features may be related to high conductivity (σ_600 °C = 0.022 S cm⁻¹) and low activation energy for conduction (0.66 eV). AC impedance spectra were involved to resolve grain interior and grain boundary resistance. Grain boundary contribution to the total resistance showed the values below 1/2 at 200-450 °C, suggesting low grain boundary effect. The motion enthalpy for the grain interior conduction decreased while the association enthalpy increased with sintering temperature up to 1300 °C, which might be possibly originated from the increase in lattice parameters with the sintering temperature.     

Structural and magnetic characterization of MnxZn1 − xFe2O4 (x = 0.2; 0.35; 0.65; 0.8; 1.0) ferrites obtained by the citrate precursor method

In this work the microstructure and magnetic properties of Mn-Zn ferrites powders were investigated. Mn_xZn1 _− xFe₂O₄ powders where x = 0.2; 0.35; 0.5; 0.65; 0.8 and 1.0 were obtained by citrate precursor method. Citrate resin precursor was burned on air atmosphere at 400 °C for 3 h. Mn-Zn powders were calcined at 950 °C during 150 min under inert atmospheres: N₂ and rarefied atmosphere. Thermal analysis of precursor resin, phase evolution and microstructure of Mn-Zn ferrites powders were investigated by TG, DTA, XRD and SEM techniques. The powders calcined under rarefied atmosphere show spinel cubic structure and contamination of α-Fe₂O₃, while powders calcined under N₂ presents only the spinel cubic structure. Particle size was observed by SEM ranging from 80 to 150 nm. The magnetic properties were measured employing a vibrating sample magnetometer (VSM). It was observed that the saturation magnetization M_s increased with the increase of Mn content. The M_s of Mn_0.8Zn_0.2Fe₂O₄ calcined on rarefied atmosphere and Mn_0.8Zn_0.2Fe₂O₄ calcined on N₂ was 23.31 emu g⁻¹ and 56.23 emu g⁻¹, respectively.     

Effects of CaTiO3 addition on the densification and microwave dielectric properties of BiSbO4 ceramics

In this study, the effects of CaTiO₃ addition on the sintering characteristics and microwave dielectric properties of BiSbO₄ were investigated. Pure BiSbO₄ achieved a sintered density of 8.46 g/cm³ at 1100 °C. The value of sintered density decreased with increasing CaTiO₃, and sintering at a temperature higher than 1100 °C led to a large weight loss (>2 wt%) caused by the volatile nature of the compound. Samples either sintered above 1100 °C or with a CaTiO₃ content exceeding 3 wt% showed poor densification. SEM micrographs revealed microstructures with bimodal grain size distribution. The size of the smaller grains ranged from 0.5 to 1.2 μm and that of the larger grains between 3 and 7 μm. The microwave dielectric properties of the (1−x) BiSbO_4−x CaTiO₃ ceramics are dependent both on the x value and on the sintering temperature. The 99.0 wt% BiSbO₄–1.0 wt% CaTiO₃ ceramic sintered at 1100 °C reported overall microwave dielectric properties that can be summarized as ε_r≈21.8, Q×f≈61,150 GHz, and τ_f≈−40.1 ppm/°C, all superior to those of the BiSbO₄ ceramics sintered with other additives.     

High permeability Ni-Cu-Zn ferrites through additive-free low-temperature sintering of nanocrystalline powders

Nanocrystalline Ni-Cu-Zn ferrite powders Ni_0.20Cu_0.20Zn_0.62Fe_1.98O_3.99 were prepared by thermal decomposition of an oxalate precursor. The particle size is 6 nm and 350 nm, respectively, for powders obtained through calcinations at 350 °C or 750 °C. The shrinkage behavior significantly changes with particle size; the temperature of maximum shrinkage rate is T_MSR = 700 °C for particles of 6 nm size and increases to T_MSR = 880 °C for particles 350 nm in size. Dense samples with a permeability of μ = 780 are obtained by sintering at 900 °C for 2 h. Mixtures of nanocrystalline and sub-micron powders allow tailoring of the shrinkage behavior. A maximum permeability of μ = 840 is obtained after sintering of a 1:1-mixture at 900 °C. This demonstrates the potential of nanocrystalline ferrites for co-firing without additives at 900 °C and integration of ferrite inductors into LTCC modules.     

Effect of Bi-substitution on the microstructure and electromagnetic properties of YCaZrVIG with low sintering temperature

Bi substituted YCaZrVIG ferrites, Y_2.3−xBi_xCa_0.7Zr_0.3V_0.2Fe_4.42O₁₂ (x=0.1, 0.25, 0.4, 0.5, 0.75) ferrites were prepared by conventional oxide method. The addition of Bi₂O₃ promoted the sintering performance and lowered the sintering temperature from 1420–1230 °C. However, it also resulted in the formation of minor second phases and the decrease of grain size. With the increase of Bi concentration, the dielectric constant increases linearly and then remains unchanged. The dielectric loss decreased firstly and then increased. The saturation magnetization (4πM_s) almost retained unchanged as the Bi concentration increased except for the sample with 0.75. The coercivity (H_c) decreased firstly and reached the minimum of 1.32 Oe at 0.25, and then rose when x>0.25, which was related to the facility of magnetic domain wall motion and magnetic moment reverse. Moderate addition of Bi also can increase the remanence (B_r) by improving sintering process. Additionally, we got the optimum electromagnetic properties in the samples with x=0.25 at 1230 °C: RD>97%, ε_r=15.7, tan δ_e=2.48×10⁻⁴, H_c=1.32Oe, 4πM_S=1663 Gs, B_r=583.91 Gs.     

Improved cycling performance of oxygen-stoichiometric spinel Li1+xAlyMn2−x−yO4+δ at elevated temperature

Li_1+xAl_yMn_2−x−yO_4±δ spinel cathode materials for lithium-ion batteries have been prepared by two methods, a specific two-step and the conventional one-step solid-state calcination methods. Compared with the conventional method, the new two-step method can guarantee the oxygen stoichiometry in spinel samples as well as reduced surface area. These characters lead to the improvement in cycling performance of spinel cathode even at elevated temperature. Moreover, the increase in doping amount of Al into Mn-spinel contributes to smearing the oxygen deficiency at high calcination temperature (1000 °C). The oxygen stoichiometric spinel samples exhibited greatly improved cycling performance. Further, Mn dissolution from spinel cathodes into the electrolyte was sufficiently suppressed even at elevated temperature of 60 °C. This beneficial influence would be reflected more remarkably in the cycles of lithium-ion full cells (spinel/C).     

Spray pyrolysis synthesis of nanostructured LiFexMn2−xO4 cathode materials for lithium-ion batteries

A series of partially Fe-substituted lithium manganese oxides LiFe_xMn_2−xO₄ (0 ≦ x ≦ 0.3) was successfully synthesized by an ultrasonic spray pyrolysis technique. The resulting powders were spherical nanostructured particles which comprised the primary particles with a few tens of nanometer in size, while the morphology changed from spherical and porous to spherical and dense with increasing Fe substitution. The densification of particles progressed with the amount of Fe substitution. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns.The as-prepared powders were then sintered at 750 °C for 4 h in air. However, the particles morphology and pure spinel phase of LiFe_xMn_2−xO₄ powders did not change after sintering. The as-sintered powders were used as cathode active materials for lithium-ion batteries, and cycle performance of the materials was investigated using half-cells Li/LiFe_xMn_2−xO₄. The first discharge capacity of Li/LiFe_xMn_2−xO₄ cell in a voltage 3.5-4.4 V decreased as the value x increased, however these cells exhibited stable cycling performance at wide ranges of charge-discharge rates.     

Varistor and Magnetic Properties of Nickel Copper Zinc Niobium Ferrite Doped with Bi2O3

Bi₂O₃ was added into nickel copper zinc niobium ferrite and treated with different thermal processes to change the grain‐boundary chemical composition. The relationship between the grain‐boundary composition and varistor properties were investigated using scanning electron microscopy, transmission electron microscopy, energy dispersion spectroscopy, and X‐ray photoelectric spectroscopy. The experimental results show that Bi₂O₃ reacts and diffuses into the spinel ferrite grain, forming bismuth iron compounds, causing the spinel ferrite chemical composition near grain boundary becomes iron deficient. The Fe deficiency spinel ferrite near the grain boundary then changes into p‐type conduction. The annealing process after sintering improves the bismuth oxide diffusion and chemical reaction near the grain boundary, which can increase the grain‐boundary resistivity. The n‐type semiconductive grain interior and p‐type spinel ferrite near the grain‐boundary combination can form a double Schottky barrier, leading the specimen to exhibit varistor properties. A multifunctional varistor‐magnetic material with a nonlinear coefficient of 10 and initial permeability of about 225 at 10 MHz can be successfully fabricated by sinteringNi_0.2881Cu_0.1825Zn_0.4802Nb_0.0096Fe_2.0168O₄ ferrites added with 5 mol% Bi₂O₃ sintered at 950°C, then annealed at 650°C for 1 h.     

Re-examination of bulk and grain boundary conductivities of Ce1−xGdxO2−δ ceramics

Powders of gadolinium-doped ceria solid solutions, Ce_1−xGd_xO_2−δ (x = 0.05, 0.1, 0.2, 0.3 and 0.4), were prepared by a freeze-drying precursor route. Dense ceramic pellets with average grain sizes in the range of several microns were obtained after sintering at 1600 °C. Cobalt nitrate was added to the powders to obtain dense ceramic samples with grain sizes in the submicrometer range at 1150 °C. The ionic conduction was analysed by impedance spectroscopy in air, to de-convolute the bulk and grain boundary contributions. The bulk conductivity at low temperature clearly decreases with increasing content of Gd whereas the activation energy increases. An alternative method is proposed to analyse the extent of defect interactions on conduction. For samples without addition of Co, the specific grain boundary conductivity increases with increasing Gd content. Addition of cobalt does not alter the bulk properties but produces an important increase in the specific grain boundary conductivity, mainly in samples with lower Gd-concentration (x = 0.05 and 0.1). Segregation of Gd and its strong interaction with charge carriers may explain the blocking effects of grain boundaries.     

Sintering,microstructure and conductivity of La2NiO4+δ ceramic

Microstructure and electrical conducting properties of La₂NiO_4+δ ceramic were investigated in the sintering temperature range 1200–1400 °C. The results demonstrate that the microstructure and electrical conducting properties of La₂NiO_4+δ ceramic are sensitive to sintering temperature. Compared with a progressive densification development with sintering temperature from 1200 to 1300 °C along with an insignificant change in grain size, there is an exaggerated grain growth in the specimens sintered at higher temperatures. Increasing sintering temperature from 1200 to 1300 °C resulted in an enhancement of electrical conducting properties. Further increase of sintering temperature exceeding 1300 °C reduced the electrical conducting properties. A close relation between the microstructure and electrical conducting properties was suggested for La₂NiO_4+δ ceramic. With respect to the electrical conducting properties, the preferred sintering temperature of La₂NiO_4+δ ceramic was ascertained to be 1300 °C. The specimen sintered at 1300 °C exhibits a generally uniform microstructure together with electrical conductivities of 76–95 S cm⁻¹ at 600–800 °C.     

Phase, microstructure evolution and sintering of Sr-doped TiB2 precursors

Precursors for the preparation of bulk Sr-doped TiB₂ composites were synthesized by modified Pechini method. The high temperature behaviour of homogeneous Sr-Ti-B-C-O gels was investigated in the range 1200-1650 °C. DTA-TG analysis of the precursor powder shows two steps of the carbothermal reduction with endothermic peaks at temperatures of 1335 °C and 1500 °C. The influence of strontium content (2, 5, 10, 20 and 50 mol.%) on the phase composition and morphology of powders at 1650 °C was studied.Due to the shift of TiB₂ diffractions and the detection of strontium in TiB₂ grains by EDX analysis the formation of Ti_1 − xSr_xB₂ solid solution is assumed in the Sr-doped powders. Finally, Sr-doped TiB₂ composites were inductive hot-pressed from the as prepared powders at 1900 °C for 7 min. The formation of SrTiO₃ phase in the powders is serving as a sintering aid during the preparation of bulk Sr-Ti-B composites. The exaggerated grain growth (grain size up to ∼60 μm) occurs during the sintering with increasing content of strontium in the precursor.     

Dielectric properties of Sm, Nd and Fe doped Bi1.5Zn0.92Nb1.5O6.92 pyrochlores

New pyrochlore ceramics have been produced by doping Sm and Nd into the Bi site and Fe into the Nb site in the Bi_1.5Zn_0.92Nb_1.5O_6.92 (BZN) pyrochlore. Doped pyrochlore ceramics were produced by conventional solid state mixing of oxides at different doping levels using the compositions of Bi_1.5−xSm_xZn_0.92Nb_1.5O_6.92, Bi_1.5−xNd_xZn_0.92Nb_1.5O_6.92 and Bi_1.5Zn_0.92Nb_1.5−xFe_xO_6.92−x. The solubility limit of cations was determined as x = 0.13, 0.18 and 0.15 for Sm, Nd and Fe, respectively. While Sm and Nd increased the dielectric constant (?), Fe doping led a decrease in ?. Dielectric constant of Sm and Nd doped BZN increased to 199 at x = 0.13 (Sm) and to 219 at x = 0.18 (Nd). At low Fe dopings (x = 0.05), the dielectric constant of BZN increased to 242 but decreased to 211 at x = 0.15. The dielectric losses were lower for Sm and Nd dopings than Fe but in all cases it was lower than 0.006. The dielectric constant of Sm, Nd and Fe doped BZN ceramics was nearly independent of frequency within the frequency range between 1 kHz and 2 MHz, but decreased considerably with temperature between 20 and 200 °C. Temperature coefficient of Sm doped BZN (−354 ppm/°C) was lower than Nd and Fe doped BZN ceramics at solubility limits (−538 ppm/°C for Nd and −565 ppm/°C for Fe).