Study of bactericidal efficiency of magnetron sputtered TiO2 films deposited at varying oxygen partial pressure

TiO₂ thin films have been deposited at different Ar:O₂ gas ratios (20:80,70:30,50:50,and 40:60 in sccm) by rf reactive magnetron sputtering at a constant power of 200 W. The formation of TiO₂ was confirmed by X-ray photoelectron spectroscopy (XPS). The oxygen percentage in the films was found to increase with an increase in oxygen partial pressure during deposition. The oxygen content in the film was estimated from XPS measurement. Band gap of the films was calculated from the UV-Visible transmittance spectra. Increase in oxygen content in the films showed substantial increase in optical band gap from 2.8 eV to 3.78 eV. The Ar:O₂ gas ratio was found to affect the particle size of the films determined by a transmission electron microscope (TEM). The particle size was found to be varying between 10 and 25 nm. The bactericidal efficiency of the deposited films was investigated using Escherichia coli (E. coli) cells under 1 h UV irradiation. The growth of E. coli cells was estimated through the Optical Density measurement by UV-Visible absorbance spectra. The qualitative analysis of the bactericidal efficiency of the deposited films after UV irradiation was observed through SEM. A correlation between the optical band gap, particle size and bactericidal efficiency of the TiO₂ films at different argon:oxygen gas ratio has been studied.     

Photogenerated cathodic protection of flower-like, nanostructured, N-doped TiO2 film on stainless steel

Flower-like, nanostructured, N-doped TiO₂ (N-TiO₂) films were fabricated using a low-temperature hydrothermal method. The morphology, crystalline phase, and composition of these flower-like nanostructured films were characterized systematically by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and UV-vis spectroscopy. The photoelectrochemical properties of N-TiO₂ films in 0.5 M NaCl solution were evaluated under illumination and in the dark through electrochemical measurements. Flower-like nanostructured TiO₂ films exhibited a drastically enhanced photocurrent in the UV light region and a notable absorption in the visible light region (600-700 nm). The negative shifts of the electrode potentials of 316L stainless steel coupled with N-doped TiO₂ photoanodes are 470 and 180 mV under UV and visible light irradiation, respectively. The flower-like, nanostructured, N-doped TiO₂ films were able to function effectively as photogenerated cathodic protection for metals under UV and visible light illumination. Such photogenerated cathodic protection could last a period of 5.5 h even in darkness.     

Microstructure characterization and photocatalytic activity of mesoporous TiO2 films with ultrafine anatase nanocrystallites

A series of mesoporous TiO₂ films on borosilicate glass with ultrafine anatase nanocrystallites were successfully synthesized using a non-acidic sol gel preparation route, which involves the use of nonionic surfactant Tween 20 as template through a self assembly pathway. The microstructure of these TiO₂ films was characterized by XRD, SEM, HR-TEM, UV-Vis spectroscopy, and N₂ adsorption-desorption isotherm analysis. Their photocatalytic activities were investigated by using creatinine as a model organic contaminate in water. It was found that all mesoporous TiO₂ films prepared with Tween 20 exhibited a partially ordered mesoporous structure. The photocatalytic activity of the TiO₂ films could be remarkably improved by increasing Tween 20 loading in the sol at the range of 50% (v/v), which yielded large amount of catalyst (anatase) on the glass support and enhanced specific surface area. The optimum Tween 20 loading was 50% (v/v) in the sol, above which good adhesion between TiO₂ films and borosilicate glass could not be maintained. The final TiO₂ film (Tween 20: final sol = 50%,v/v) exhibits high BET surface area (∼ 120 m²/g) and pore volume (0.1554 cm³/g), ultrafine anatase nanocrystallinity (7 nm), uniform and crack free surface morphology, and improved photocatalytic activity.     

Modification of TiO2 nanorods by Bi2MoO6 nanoparticles for high performance visible-light photocatalysis

In this work, TiO₂ nanorods were prepared by a hydrothermal process and then Bi₂MoO₆ nanoparticles were deposited onto the TiO₂ nanorods by a solvothermal process. The nanostructured Bi₂MoO₆/TiO₂ composites were extensively characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The photocatalytic activity of the Bi₂MoO₆/TiO₂ composites was evaluated by degradation of methylene blue. The Bi₂MoO₆/TiO₂ composites exhibit higher catalytic activity than pure Bi₂MoO₆ and TiO₂ for degradation of methylene blue under visible light irradiation (λ > 420 nm). Further investigation revealed that the ratio of Bi₂MoO₆ to TiO₂ in the composites greatly influenced their photocatalytic activity. The experimental results indicated that the composite with Bi₂MoO₆:TiO₂ = 1:3 exhibited the highest photocatalytic activity. The enhancement mechanism of the composite catalysts was also discussed.     

Structural and dielectric properties of Bi2Zn2/3Nb4/3O7 thin films prepared by pulsed laser deposition at low temperature for embedded capacitor applications

Bi₂Zn_2/3Nb_4/3O₇ thin films were deposited on Pt/TiO₂/SiO₂/Si(1 0 0) substrates at a room temperature under the oxygen pressure of 1-10 Pa by pulsed laser deposition. Bi₂Zn_2/3Nb_4/3O₇ thin films were then post-annealed below 200 °C in a rapid thermal process furnace in air for 20 min. The dielectric and leakage current properties of Bi₂Zn_2/3Nb_4/3O₇ thin films are strongly influenced by the oxygen pressure during deposition and the post-annealing temperature. Bi₂Zn_2/3Nb_4/3O₇ thin films deposited under 1 Pa oxygen pressure and then post-annealed at a temperature of 150 °C show uniform surface morphologies. Dielectric constant and loss tangent are 57 and 0.005 at 10 kHz, respectively. The high resolution TEM image and the electron diffraction pattern show that nano crystallites exist in the amorphous thin film, which may be the origin of high dielectric constant in the Bi₂Zn_2/3Nb_4/3O₇ thin films deposited at low temperatures. Moreover, Bi₂Zn_2/3Nb_4/3O₇ thin film exhibits the excellent leakage current characteristics with a high breakdown strength and the leakage current density is approximately 1 × 10⁻⁷ A/cm² at an applied bias field of 300 kV/cm. Bi₂Zn_2/3Nb_4/3O₇ thin films are potential materials for embedded capacitor applications.     

Preparation of large scale photocatalytic TiO2 films by the sol-gel process

Nanocrystalline titanium dioxide films were formed on frosted and clear borosilicate glass with a large surface area (12 × 22 cm) using doctor blade and spray coating techniques. The films were subjected to a high temperature treatment at 550 °C. X-ray diffraction (XRD) analysis indicated that the TiO₂ films contain only the anatase phase. Optical microscopy was used to determine the morphology changes after the deposition of each layer. Scanning electron microscopy (SEM) was used to study the films surface morphology. The large scale TiO₂ films produced showed a high photocatalytic activity which was evaluated by the degradation of methyl orange (MO) in aqueous solution (10 mg L^− 1) under illumination of a UV light source with an overall irradiance of 0.9 mW cm^− 2. UV-visible spectrophotometry was used to monitor the degradation of MO through the decrease of the main absorbance peak at 464 nm. The results demonstrated that a complete decomposition of MO could be achieved after 2 h of UV irradiation.     

Photocatalytic performance of nano-photocatalyst from TiO2 and Fe2O3 by mechanochemical synthesis

Nano-particles of homogeneous solid solution between TiO₂ and Fe₂O₃ (up to 10 mol%) have been prepared by mechanochemical milling of TiO₂ and yellow Fe₂O₃/red Fe₂O₃/precipitated Fe (OH)₃ using a planetary ball mill. Such novel solid solution cannot be prepared by conventional co-precipitation technique. A preliminary investigation of photocatalytic activity of mixed oxide (TiO₂/Fe₂O₃) on photo-oxidation of different organic dyes like Rhodamine B (RB), Methyl orange (MO), Thymol blue (TB) and Bromocresol green (BG) under visible light (300-W Xe lamp; λ > 420 nm) showed that TiO₂ having 5 mol% of Fe₂O₃ (YFT1) is 3-5 times higher photoactive than that of P25 TiO₂. The XRD result did not show the peaks assigned to the Fe components (for example Fe₂O₃, Fe₃O₄, FeO₃, and Fe metal) on the external surface of the anatase structure in the Fe₂O₃/TiO₂ attained through mechanochemical treatment. This meant that Fe components were well incorporated into the TiO₂ anatase structure. The average crystallite size and particle size of YFT1 were found to be 12 nm and 30 ± 5 nm respectively measured from XRD and TEM conforming to nanodimensions. Together with the Fe component, they absorbed wavelength of above 387 nm. The band slightly shifted to the right without tail broadness, which was the UV absorption of Fe oxide in the Fe₂O₃/TiO₂ particle attained through mechanochemical method. This meant that Fe components were well inserted into the framework of the TiO₂ anatase structure. EPR and magnetic susceptibility show that Fe³⁺ is in low spin state corresponding to μ_B = 1.8 BM. The temperature variation of μ_B shows that Fe³⁺ is well separated from each other and does not have any antiferromagnetic or ferromagnetic interaction. The evidence of Fe³⁺ in TiO₂/Fe₂O₃ alloy is also proved by a new method that is redox titration which is again support by the XPS spectrum.     

Effect of polyethylene glycol on hydrophilic TiO2 films: Porosity-driven superhydrophilicity

Polyethylene glycol (PEG) 2000 was used as a templating reagent to synthesize porous TiO₂ thin film by sol-gel process. The nanopores resulting from the presence of growing cracks were ultimately formed on the surface when PEG content was higher than the critical value. Surprisingly, stable pore structure disappeared and surface became fluctuating and dehiscent after PEG amount increased to 0.02 M. Besides, two main hypotheses were proposed in order to explain this superhydrophilic behavior, namely the Wenzel and Cassie wetting impregnating models. Furthermore, the transition between these two wetting regimes was investigated and the criteria for the design and construction of Cassie impregnating wetting surface was also discussed. It was found that Cassie state shifting from Wenzel state could be easily achieved with increasing hole depth on TiO₂ surface. The study of transition between Wenzel and Cassie impregnating wetting regimes on porous films provides valuable wetting mechanism of porosity-driven wettability for the design of superhydrophilic surfaces.     

Low temperature growth of nanocrystalline TiO2 films with Ar/O2 low-field helicon plasma

TiO₂ thin films were deposited on silicon wafer substrates by low-field (1 < B < 5 mT) helicon plasma assisted reactive sputtering in a mixture of pure argon and oxygen. The influence of the positive ion density on the substrate and the post-annealing treatment on the films density, refractive index, chemical composition and crystalline structure was analysed by reflectometry, Rutherford backscattering spectroscopy (RBS) and X-ray diffraction (XRD). Amorphous TiO₂ was obtained for ion density on the substrate below 7 × 10¹⁶ m^− 3. Increasing the ion density over 7 × 10¹⁶ m^− 3 led to the formation of nanocrystalline (~ 15 nm) rutile phase TiO₂. The post-annealing treatment of the films in air at 300 °C induced the complete crystallisation of the amorphous films to nanocrystals of anatase (~ 40 nm) while the rutile films shows no significant change meaning that they were already fully crystallised by the plasma process. All these results show an efficient process by low-field helicon plasma sputtering process to fabricate stoichiometric TiO₂ thin films with amorphous or nanocrystalline rutile structure directly from low temperature plasma processing conditions and nanocrystalline anatase structure with a moderate annealing treatment.     

Electrodeposition of sol-enhanced nanostructured Ni-TiO2 composite coatings

A novel electroplating method has been developed to produce nanocrystalline metal-matrix nano-structured composite coatings. A small amount of transparent TiO₂ sol was added into the traditional electroplating Ni solution, leading to the formation of nanocrystalline Ni-TiO₂ composite coatings. These coatings have a smooth surface. The Ni nodules changed from traditional pyramid-like shape to spherical shape. The grain size of Ni was also significantly reduced to the level of 50 nm. It was found that the amorphous anatase TiO₂ nano-particles (∼ 10 nm) were highly dispersed in the coating matrix. The microhardness was significantly increased from 320 HV₁₀₀ of the traditional Ni coating to 430 HV₁₀₀ of the novel composite coating with 3.26 wt.% TiO₂. Correspondingly, the wear resistance of the composite coating was improved by ∼ 50%.     

Perpendicular magnetic anisotropy in 70 nm CoFe2O4 thin films fabricated on SiO2/Si(1 0 0) by the sol-gel method

Cobalt ferrite CoFe₂O₄ films were fabricated on SiO₂/Si(1 0 0) by the sol-gel method. Films crystallized at/above 600 °C are stoichiometric as expected. With increase of the annealing temperature from 600 °C to 750 °C, the columnar grain size of CoFe₂O₄ film increases from 13 nm to 50 nm, resulting in surface roughness increasing from 0.46 nm to 2.55 nm. Magnetic hysteresis loops in both in-plane and out-of-plane directions, at different annealing temperatures, indicate that the films annealed at 750 °C exhibit obvious perpendicular magnetic anisotropy. Simultaneously, with the annealing temperature increasing from 600 °C to 750 °C, the out of plane coercivity increases from 1 kOe to 2.4 kOe and the corresponding saturation magnetization increases from 200 emu/cm³ to 283 emu/cm³. In addition, all crystallized films exhibit cluster-like structured magnetic domains.     

Influence of pre-oxidation on the hot corrosion of Ti3SiC2 in the mixture of Na2SO4-NaCl melts

Polycrystalline Ti₃SiC₂ suffered from serious hot corrosion attack in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C. In order to improve the hot corrosion resistance of this material, pre-oxidation treatment was conducted at 1200 °C in air for 2 h. A duplex oxide scale with an outer layer of TiO₂ and an inner layer of a mixture of TiO₂ and SiO₂ was formed during the pre-oxidation. Because the outer oxide layer of the pre-oxidation treated specimens could inhibit hot corrosion process, they exhibited good hot corrosion resistance in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C for 50 h. However, during the hot corrosion the outer layer of TiO₂ would degrade gradually. Once the outer layer damaged, the hot corrosion rate increased sharply, the corrosion behavior was similar to Ti₃SiC₂ corroded under the same conditions. The microstructure and phase compositions of the hot corrosion samples were investigated by SEM/EDS and XRD.     

Charge transport and recombination in dye-sensitized solar cells based on hybrid films of TiO2 particles/TiO2 nanotubes

In this paper, anodic TiO₂ nanotubes are blended into the TiO₂ mesoporous films based on P25 nanoparticles to assemble a list of dye-sensitized solar cells (DSSCs) with different nanotube concentrations. The electron properties of transport and recombination in the fabricated DSSCs are studied by using electrochemical impedance spectroscopy and the open-circuit voltage decay technique under AM 1.5 illumination. Results indicate that the electron lifetime increases with increasing the concentration of the anodic TiO₂ nanotubes, the electron transport time at a blending level of 10 wt% TiO₂ nanotubes is short as compared to that at 0 wt%, and above 10 wt%, the electron transport time has a trend of becoming large. Due to the combining effects of the electron transport and recombination, the electron collecting efficiency and the electron diffusion length obtain maxima at a blending level of 10 wt% nanotubes, which results in a highest short circuit current and a maximum energy conversion efficiency at this point in the DSSCs. This study gives a clear explanation for the performance enhancement of TiO₂ particle-based DSSCs at a blending level of 10 wt% anodic TiO₂ nanotubes and for the performance decrease at a blending level over 10 wt% anodic TiO₂ nanotubes from the angle of the electron transport and recombination. This study also supplies a feasible and easy way to improve the performance of particle-based DSSCs by restraining electron recombination and accelerating electron transportation.     

Investigations on synthesis of HfB2 and development of a new composite with TiSi2

This paper presents the results of investigation carried out on synthesis and densification of monolithic HfB₂ and the effect of TiSi₂ as sinter additive. Pure phase HfB₂ was prepared by boron carbide reduction of HfO₂ and hot pressed to full density with the addition of TiSi₂. Isothermal oxidation study of this composite was carried out at 850 °C up to 64 h. Formation of HfB₂ was seen at 1200 °C but pure HfB₂ was formed at a much higher temperature of 1875 °C in vacuum. Hot pressing of HfB₂ at 1850 °C and 35 MPa pressure gave a compact of 80% TD. Addition of TiSi₂ helped in achieving a much higher density at a lower temperature of 1600 °C and a pressure of 20 MPa. A fully dense composite of HfB₂ and TiSi₂ was obtained with 15% TiSi₂. Hardness and fracture toughness of this composite were 27.4 ± 1.9 GPa and 6.6 ± 0.2 MPa m^1/2, respectively. Considerable deflection was observed in the crack propagation in composites. Oxidation studies indicated the formation of HfO₂, SiO₂, TiO₂ and HfSiO₄ with some glassy phase and the composite with 15% TiSi₂ was seen to be completely covered with a protective glassy layer.     

Laser-induced enhancement of the surface hardness of nanoparticulate TiO2 self-cleaning layer

We here report that the abrasion resistance of nanoparticulate TiO₂ self-cleaning layers can be highly enhanced without a considerable loss of photocatalytic capability. TiO₂ coating layers solution-deposited onto the glass substrate were irradiated by a pulsed ultraviolet (UV) laser at 355 nm, which modified the surface morphologies via laser-induced local melting of TiO₂ nanoparticles. The surface hardness, measured by pencil scratch test, improved with increasing laser power (P). While an unmodified TiO₂ layer revealed a hardness of 6B, it increased to 2H after the surface was irradiated at P = 0.3 W. Almost all of the stearic acid deposited on an unmodified sample disappeared after UV exposure for 12 h. The photocatalytic decomposition was slowed down on laser-irradiated TiO₂ surfaces and this is attributed to the reduction of specific surface areas as a result of the morphological modifications. However, a TiO₂ layer hardened to 2H still exhibited fairly good photocatalytic activity, decomposing more than 75% of the stearic acid after exposure for the same duration.     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

Photosensitive nanostructured TiO2 grown at room temperature by novel “bottom-up” approached CBD method

The current paper incorporates with a “bottom-up” approached chemical bath deposition method to grow titanium dioxide (TiO₂) nanostructure at room temperature on glass and stainless steel substrates. The room temperature deposited TiO₂ films are heat treated at 673 K for 1 h in air and the corresponding change in structural, morphological and optical properties are studied by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and UV-VIS-NIR spectrophotometer. The heat-treated films are utilized as a photocathode in photoelectrochemical (PEC) cell in 1 M NaOH electrolyte. The experimental results show that, the CBD method allows formation of photosensitive, anatase TiO₂ thin film, which can be potentially tuned in many functional applications with feasibility.     

P-type transparent conducting SnO2:Zn film derived from thermal diffusion of Zn/SnO2/Zn multilayer thin films

Highly transparent, p-type conducting SnO₂:Zn thin films are prepared from the thermal diffusion of a sandwich structure of Zn/SnO₂/Zn multilayer thin films deposited on quartz glass substrate by direct current (DC) and radio frequency (RF) magnetron sputtering using Zn and SnO₂ targets. The deposited films were annealed at various temperatures for thermal diffusion. The effect of annealing temperature and time on the structural, electrical and optical performances of SnO₂:Zn films was studied. XRD results show that all p-type conducting films possessed polycrystalline SnO₂ with tetragonal rutile structure. Hall effect results indicate that the treatment at 400 °C for 6 h was the optimum annealing parameters for p-type SnO₂:Zn films which have relatively high hole concentration and low resistivity of 2.389 × 10¹⁷ cm^− 3 and 7.436 Ω cm, respectively. The average transmission of the p-type SnO₂:Zn films was above 80% in the visible light range.     

Effects of Mg substitution on the structural, optical, and electrical properties of CuAlO2 thin films

Mg-doped CuAlO₂ thin films are prepared by the chemical solution method. The XRD results show that the solid solubility of Mg species on Al sites in CuAlO₂ lattice is lower than 2 at.%. When less than 2 at.% of Mg is added to the CuAlO₂ film, the surface roughness of the films was reduced with Mg substitution. Moreover, the c-axis orientation of the films improves because the in-plane fusion between CuAlO₂ crystallites is hindered. Optical and electrical measurements show that substituting Al³⁺ in the films with Mg²⁺ increases both their transmittance in the visible region and their optical band gaps. As well, their electrical conductivity is enhanced. At 300 K, the conductivity of the 1 at.% Mg-doped sample is up to 5.2 × 10⁻³ S/cm. Thus, Mg-doped CuAlO₂ films may have potential applications as transparent conductive oxides.