Flexible electronic‐paper active‐matrix displays

Abstract— A QVGA active‐matrix backplane was produced on a 25‐μm thin plastic substrate. A four‐mask photolithographic process was used. The insulator layer and the semiconductor layer were organic material processed from solution. This backplane was a combination of the electrophoretic display effects supplied by SiPix and E‐Ink Corp., resulting in electronic‐paper displays with a thickness of 150 and 100 μm, respectively; this is the world's thinnest active‐matrix display ever made.     

A scalable manufacturing process for flexible active‐matrix e‐paper displays

Abstract— A scalable manufacturing process for fabricating active‐matrix backplanes on low‐cost flexible substrates, a key enabler for electronic‐paper displays, is presented. This process is based on solution processing, ink‐jet printing, and laser patterning. A multilayer architecture is employed to enable high aperture ratio and array performance. These backplanes were combined with E Ink electrophoretic media to create high‐performance displays that have high contrast, are bistable, and can be flexed repeatedly to a radius of curvature of 5 mm.     

Development of active‐matrix electronic‐ink displays for handheld devices

Abstract— Interest in the use of electrophoretic displays for smart handheld applications has grown tremendously over the past few years. Since the launch of the Philips and E Ink joint development effort in February 2001, material parameters, TFT backplane, electronic hardware and software and modulization skills have been developed to make this promising display concept into a real product. The first commercial launch of active‐matrix electronic‐ink display modules is planned for mid 2004.     

A controller design for micro‐cup active‐matrix electrophoretic displays

Abstract— The active‐matrix electrophoretic display (AMEPD) has been commonly used for the applications of smart handheld reading devices such as e‐books and e‐newspapers. This paper presents a controller IC design for the AMEPD backend system which reduces the total hardware cost compared to that of the conventional design. By contrast, this study also provides a driving method for image displays. The prototyped controller is connected to a 6‐in. AMEPD panel, and good display quality has demonstrated the effectiveness of the proposed controller design.     

Polymer‐based transistors used as pixel switches in active‐matrix displays

A 2‐in. active‐matrix display was demonstrated, containing 4096 solution‐processed polymer‐based transistors. By using the polymer‐dispersed liquid‐crystal display (LCD) effect, this results in a reflective, low‐power display with paper‐like contrast. The influence of the transistor parameters on the display performance is analyzed by use of a model for charging and discharging of the pixel capacitors. Good agreement was obtained between the model and the experimental data. Scaling behavior allows estimation of the performance required for transistors in a quarter‐VGA display. These requirements are met by solution‐processed pentacene transistors.     

A flexible,organic QVGA display with gray‐scale capability

Abstract— A flexible 4.7‐in. QVGA active‐matrix display was demonstrated, containing 76,800 solution‐processed organic transistors. The combination of our plastic active‐matrix backplane with electrophoretic‐ink display material developed by E‐Ink resulted in a reflective low‐power display with paper‐like appearance. By using high‐performance organic transistors, it was possible to generate 2‐bit images on the display. The display can be bent to a radius below 2 cm.     

A rollable,organic electrophoretic QVGA display with field‐shielded pixel architecture

Abstract— A 100‐μm thin QVGA display was made by combining a 25‐μm thin organic transistor active‐matrix backplane with an electrophoretic display film. High contrast and low crosstalk was achieved by the addition of a field shield to the backplane. The display can be bent repeatedly to a radius of 2 mm without any performance loss. Extended mechanical tests at a radius of curvature of 7.5 mm show that the display can be rolled at least 30,000 times without noticeable degradation.     

Organic‐polymer thin‐film transistors for active‐matrix flat‐panel displays?

Abstract— Organic‐polymer‐based thin‐film transistors (OP‐TFTs) look very promising for flexible, large‐area, and low‐cost organic electronics. In this paper, we describe devices based on spin‐coated organic polymer that reproducibly exhibit field‐effect mobility values around 5 × 10^?3 cm²/V‐sec. We also address fabrication, performance, and stability issues that are critical for the use of such devices in active‐matrix flat‐panel displays.     

Flexible active‐matrix OLED displays: Challenges and progress

Abstract— Organic light‐emitting‐device (OLED) devices are very promising candidates for flexible‐display applications because of their organic thin‐film configuration and excellent optical and video performance. Recent progress of flexible‐OLED technologies for high‐performance full‐color active‐matrix OLED (AMOLED) displays will be presented and future challenges will be discussed. Specific focus is placed on technology components, including high‐efficiency phosphorescent OLED technology, substrates and backplanes for flexible displays, transparent compound cathode technology, conformal packaging, and the flexibility testing of these devices. Finally, the latest prototype in collaboration with LG. Phillips LCD, a flexible 4‐in. QVGA full‐color AMOLED built on amorphous‐silicon backplane, will be described.     

A Flexible electronic‐paper display with an ultra‐thin and flexible LSI driver using quick‐response liquid‐powder technology

Abstract— A thin and flexible LSI driver with a thickness of less than 35 μm for a passive‐matrix‐driven Quick‐Response Liquid‐Powder Display (QR‐LPD?) was successfully mounted onto the flexible printed circuit (FPC) and the back substrates of a flexible QR‐LPD?. Amounted LSI driver on a plastic substrate shows no significant degradation in the driving performances and maintains physical flexibility without any connection failures. This technology can realize a fully flexible electronic paper in combination with a plastic‐substrate QR‐LPD? fabricated by a roll‐to‐roll process.     

A new current‐mirror pixel circuit employing poly‐Si TFTs for active‐matrix organic light‐emitting‐diode displays

Abstract— A novel active‐matrix organic light‐emitting‐diode (AMOLED) display employing a new current‐mirror pixel circuit, which requires four‐poly‐Si TFTs and one‐capacitor and no additional signal lines, has been proposed and sucessfully fabricated. The experimental results show that a new current mirror can considerably compensate luminance non‐uniformity and scale down a data current more than a conventional current‐mirror circuit in order to reduce the pixel charging time and increase the minimum data current. Compared with a conventional two‐TFT pixel, the luminance non‐uniformity induced by the grain boundaries of poly‐Si TFTs can be decreased considerably from 41% to 9.1%.     

Suspension‐deposited carbon‐nanotube networks for flexible active‐matrix displays

Abstract— The unique properties of carbon nanotubes (CNTs) promise innovative solutions for a variety of display applications. The CNTs can be deposited from suspension. These simple and low‐cost techniques will replace time‐consuming and costly vacuum processes and can be applied to large‐area glass and flexible substrates. Single‐walled carbon nanotubes (SWNTs) have been used as conducting and transparent layers, replacing the brittle ITO, and as the semiconducting layer in thin‐film transistors (TFTs). There is no need for alignment because a CNT network is used instead of single CNTs. Both processes can be applied to glass and to flexible plastic substrates. The transparent and conductive nanotube layers can be produced with a sheet resistance of 400 Ω/□ at 80% transmittance. Such layers have been used to produce directly addressed liquid‐crystal displays and organic light‐emitting diodes (OLED). The CNT‐TFTs reach on/off ratios of more than 10⁵ and effective charge‐carrier mobilities of 1 cm²/V‐sec and above.     

Microcup® displays: Electronic paper by roll‐to‐roll manufacturing processes

Abstract— Rolls of flexible displays or electronic paper have recently been prepared by a high‐speed roll‐to‐roll manufacturing process based on SiPix's novel Microcup® and top‐sealing technologies. Both Microcup® electrophoretic displays (EPDs) and LCDs have been demonstrated. The display rolls are format flexible and may be cut into desirable size and shape for a variety of applications. High‐performance flexible passive‐matrix Microcup® EPDs having a wide range of threshold voltages have also been demonstrated.     

Color displays and flexible displays using quick‐response liquid‐powder technology for electronic paper

Abstract— Color displays and flexible displays that use electronic liquid powder have been developed. Novel types of color displays using either a colored powder or a color filter are discussed. We have also developed a flexible display with low‐cost substrate films with a high‐throughput roll‐to‐roll manufacturing method. These technologies enable a QR‐LPD to be widely used as an electronic‐paper display.     

Letter: A new compensation pixel circuit with metal oxide thin‐film transistors for active‐matrix organic light‐emitting diode displays

This paper presents a novel compensation pixel circuit for active‐matrix organic light‐emitting diode displays, in which the coupling effect mask technology is developed to compensate the threshold voltage of driving thin‐film transistor whether it is positive or negative. Twenty discrete compensation pixel circuits have been fabricated by In‐Zn‐O thin‐film transistors process. It is measured that the non‐uniformity of the proposed pixel circuit is significantly reduced with an average value of 8.6%. Furthermore, the organic light‐emitting diode emission current remains constant during 6 h continuous operation, which also confirms the validity of the proposed pixel circuit.     

A flexible 2.1‐in. active‐matrix electrophoretic display with high resolution and a thickness of 100 μm

Abstract— A paper‐thin QVGA, flexible 2.1‐in. active‐matrix electrophoretic display (AMEPD) that features 100‐μm thick and a 192‐ppi resolution has been developed. An LTPS‐TFT backplane with integrated peripheral driver circuits was first fabricated on a glass substrate and then transferred to a very thin (30‐μm) plastic film by employing surface‐free technology by laser ablation/annealing (SUFTLA®). A micro‐encapsulated electrophoretic imaging sheet was laminated on the backplane. A supporting substrate was used to support the LTPS‐TFT backplane. Fine images were successfully displayed on the rollable AM‐EPD. The integrated driver circuits dramatically reduce the number of external connection terminals, thus easily boosting the reliability of electrical connections even on such a thin plastic film.     

Ambient‐light‐adaptive image quality enhancement for full‐color e‐paper displays using a saturation‐based tone‐mapping method

Full‐color e‐paper displays that have a small color gamut encounter image tone distortions and contour artifacts in high‐saturation regions. To solve these issues, in this paper, we comprehensively measure the colorimetric responses of input image signals and demonstrate that the perceptual colorfulness in terms of chroma abnormally declines when the input saturation is beyond a certain value. Accordingly, saturation‐based tone‐mapping curves are developed to map the abnormal high saturation to the range that the display is able to normally render. By testing several test charts and natural images, the recoveries of the original image tones and the removals of the contour artifacts are experimentally verified. More important, by discussing how to conduct a database of tone‐mapping curves for different ambient lights and utilize the database for an unknown ambient light, the proposed method is proven to be completely ambient light adaptive.     

Towards large‐area full‐color active‐matrix printed polymer OLED television

Abstract— We have developed a new multi‐head polymer OLED ink‐jet‐printing technology to make large‐screen OLED television displays. This printer is used to make a 13‐in.‐diagonal 16:9‐format polymer‐OLED prototype driven by an LTPS active matrix with a pixel circuit which compensates for TFT threshold‐voltage variations. A novel scrolling‐bar addressing scheme is used to reduce motion artifacts and to make sparkling images with a high local peak brightness. The scalability of the polymer‐OLED technology to larger sizes for television applications is discussed.     

High‐mobility solution‐processed organic thin‐film transistor array for active‐matrix color liquid‐crystal displays

Abstract— A solution‐processed organic thin‐film‐transistor array to drive a 5‐in.‐diagonal liquid‐crystal display has been fabricated, where semiconductor films, a gate dielectric film, and passivation films have all been formed using solution processes. A field‐effect mobility of 1.6 cm²/V‐sec, which is among the highest for solution‐processed organic thin‐film transistors ever reported, was obtained. This result is due to semiconductor material with large‐grain‐sized pentacene crystals formed from a solution and adoption of three‐layered passivation films that minimize the performance degradation of organic thin‐film transistors.     

Modeling of threshold‐voltage‐shift dependency on drain bias in amorphous‐silicon thin‐film transistors in active‐matrix organic light‐emitting‐diode displays

Abstract— A theoretical model to interpret appearances of the threshold voltage shift in hydrogenated amorphous‐silicon (a‐Si:H) thin‐film transistors (TFTs) is developed to better understand the instability of a‐Si:H TFTs for the driving transistors in active‐matrix organic light‐emitting‐diode (AMOLED) displays. This model assumes that the defect creation at channel in a‐Si:H is proportional to the carrier concentration, leading to the defect density varying along the channel depending on the bias conditions. The model interprets a threshold‐voltage‐shift dependency on the drain‐stress bias. The model predicts the threshold voltage shift stressed under a given gate bias applying the drain saturation voltage is 66% of that with zero drain bias, and it even goes down to 50–60% of that when stressed by applying twice the drain saturation voltage.