ZrO2–CeO2 Alloys as Candidate Structural Materials for Cryogenic Application

Zirconia-based ceramics are considered as support materials for superconducting magnets, and the relationship between composition and mechanical properties at cryogenic temperature is reported. Ce-TZP materials with CeO₂ content between 14.5 and 16.5 mol% can be made with high strength (600 MPa) and high toughness (12 MPa·m^1/2) at cryogenic temperatures.     

Sol–Gel Synthesis and Photocatalytic Activity of CeO2/TiO2 Nanocomposites

Uniform CeO₂ / TiO₂ composite nanoparticles with different Ce/Ti molar ratios have been successfully synthesized via the sol–gel method. The samples were characterized using differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The surface state analysis by means of X-ray photoelectron spectroscopy (XPS) shows that the Ti element mainly exists as a chemical state of Ti⁴⁺, while the Ce element exists as a mixture of Ce³⁺ and Ce⁴⁺ oxidation states. The photocatalytic degradation of methyl orange (MeO) in CeO₂ / TiO₂ suspension was investigated. The results indicate that the CeO₂/TiO₂ nanocomposites show higher photocatalytic activity than pure TiO₂. Photodegradation of MeO can be improved by increasing the Ce/Ti molar ratio in the initial 15 min.     

Synthesis of Al2O3–CeO2 Mixed Oxide Nano-Powders

Ceria (CeO₂)-doped alumina (Al₂O₃) composite nano-particles were synthesized using sucrose as a chelating agent and template material. As-synthesized powders were characterized using X-ray diffraction technique for their phase analysis, BET surface area analyzer for specific average surface area, and transmission electron microscope for particle size and morphology. Both CeO₂ and Al₂O₃ delayed the amorphous to crystalline phase transformation for each other. These composite nano-powders had particle size in the range of 20–50 nm with an aspect ratio of 1.5 with platelet morphology and surface area between 100 and 300 m²/g. Synthesis parameters were optimized varying the sucrose to metal ion ratio, calcinations time and temperature. This method can be applied to synthesize various monolithic and mixed metal oxide based ceramic nano-particles.     

Nano-Blast Synthesis of Nano-size CeO2–Gd2O3 Powders

CeCl₃·7H₂O and GdCl₃·6H₂O that were dissolved in water were precipitated with urea (NH₂CONH₂) to produce matrix agglomerates for three-component nano-reactors. Mixing hexamethylenetetramine with dilute nitric acid resulted in the formation of well-dispersed nano-particles of cyclotrimetilene trinitramine (C₃H₆N₆O₆) (RDX) in the solvent. Nano-reactors were produced by impregnating the nano-C₃H₆N₆O₆ into the matrix agglomerates of an intermediate complex of cerium and gadolinium compounds. Blast initiation of the C₃H₆N₆O₆ resulted in extremely rapid detonation and gaseous products formation at temperatures of 2000°–5000°C, which were compressed into a volume nearly equal to the initial volume of each RDX nano-particle. Multiple "nano-blasts" occurred in the volume of each nano-reactor. The impact of the blast waves led to fragmentation of the surrounding matter. The evolution of a large volume of gaseous products dissipated the heat of the process and limited temperature increase, thus reducing the possibility of local sintering among the primary particles. The short-term high temperature generated during the blasts enhanced the solid solubility of the metal oxides. Uniform aggregates of 22∼74 nm consisting of 6∼14 nm crystallites of gadolinia in ceria solid solution were synthesized.     

Transformation Toughening in Large-Grain-Size CeO2-Doped ZrO2 Polycrystals

The fracture and transformation behavior of tetragonal polycrystalline ZrO₂ alloys containing 18 mol% CeO₂ (Ce-TZP) was investigated. In the absence of applied stress the tetragonal phase was found to be stable in large-grained (>30 μm) samples at room temperature. The monoclinic phase was detected in regions of high residual stress near hardness indentations although no evidence of a wake of monoclinic phase along the fracture surface was observed. The fracture toughness increased from 4 to 7 MPa · m^1/2 as density and/or grain size increased. It is proposed that the relatively high toughness of these materials is due to the occurrence of stress-driven tetragonal-to-monoclinic transformation near the crack tip, which reverses when the crack has passed.     

Properties of CeO2–Al2O3–SiO2 Glasses Prepared in Air

Properties of 15–30 mol% CeO₂/23 mol% Al₂O₃/62–47 mol% SiO₂ glasses prepared in air have been investigated in this study. Experimental results show that the glass transformation temperature, the dilatometric softening temperature, and the transmittance in the visible region decrease with increasing ceria content; but the thermal expansion coefficient, the bulk density, and the microhardness increase with increasing ceria content.     

Electrical Conductivities of (CeO2)1−x(Y2O3)x Thin Films

Electrical properties of CeO₂ thin films of different Y₂O₃ dopant concentration as prepared earlier were studied using impedance spectroscopy. The ionic conductivities of the films were found to be dominated by grain boundaries of high conductivity as compared with that of the bulk ceramic of the same dopant concentration sintered at 1500°C. The film grain-boundary conductivities were investigated with regard to grain size, grain-boundary impurity segregation, space charge at grain boundaries, and grain-boundary microstructures. Because of the large grain boundary and surface area in thin films, the impurity concentration is insufficient to form a continuous highly resistive Si-rich glassy phase at grain boundaries, such that the resistivity associated with space-charge layers becomes important. The grain-boundary resistance may originate from oxygen-vacancy-trapping near grain boundaries from space-charge layers. High-resolution transmission electron microscopy coupled with a trans-boundary profile of electron energy loss spectroscopy gives strong credence to the space-charged layers. Since the conductivities of the films were observed to be independent of crystallographic texture, the interface misorientation contribution to the grain-boundary resistance is considered to be negligible with respect to those of the impurity layer and space-charge layers.     

CeO2−CoO Phase Diagram

Phase equilibria in the CeO₂−CoO system at temperatures above 1500°C were investigated. The microstructures and the phase compositions of the DTA (differential thermal analysis) samples and the quenched solid pellets were analyzed using SEM (scanning electron microscope), EDX (energy dispersive X-ray), and WDX (wavelength dispersive X-ray). A eutectic reaction was found at 1645 ± 5°C. The eutectic point was calculated to be at 82 ± 1.5 mol% CoO. The eutectic phases were the CeO₂-rich phase (containing <5 mol% CoO) and the CoO-rich phase (containing ∼0.5 mol% CeO₂). At 1580°C, the solubility of CoO in CeO₂ was ∼3 mol%.     

Thermal Expansion of CeO2, Ho2O3, and Lu2O3 from 100° to 300°K by an X-Ray Method

Thermal expansion of CeO₂, Ho₂O₈, and Lu₂O₃ was determined from 100° to 300°K by a back-reflection X-ray technique. The variation of thermal expansion with temperature is the same as that of specific heat for CeO₂ and Ho₂O₃; these oxides obey the Grueneisen model of thermal expansion in the temperature range studied.     

Durable Transition‐Metal‐Carbide‐Supported Pt–Ru Anodes for Direct Methanol Fuel Cells

Molybdenum carbide (MoC) and tungsten carbide (WC) are synthesized by direct carbonization method. Pt–Ru catalysts supported on MoC, WC, and Vulcan XC‐72R are prepared, and characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, and transmission electron microscopy in conjunction with electrochemistry. Electrochemical activities for the catalysts towards methanol electro‐oxidation are studied by cyclic voltammetry. All the electro‐catalysts are subjected to accelerated durability test (ADT). The electrochemical activity of carbide‐supported electro‐catalysts towards methanol electro‐oxidation is found to be higher than carbon‐supported catalysts before and after ADT. The study suggests that Pt–Ru/MoC and Pt–Ru/WC catalysts are more durable than Pt–Ru/C. Direct methanol fuel cells (DMFCs) with Pt–Ru/MoC and Pt–Ru/WC anodes also exhibit higher performance than the DMFC with Pt–Ru/C anode.     

Zirconium–Hafnium Interdiffusion in Polycrystalline Fluorite-Cubic CeO2─ZrO2─HfO2 Solid Solution

Zr–Hf interdiffusion was studied in the temperature range of 1650° to 1850°C in air for polycrystalline fluorite-cubic systems of 90CeO₂·10(Zr_{1- x} Hf _x )O₂ and 60CeO₂·40(Zr_{1- x} Hf _x )O₂. Lattice and grain-boundary diffusion parameters were calculated from the Zr–Hf concentration distributions by using the grain-boundary diffusion equation of Oishi and Ichimura. The cation iattice diffusivity was close to that in the fluorite-cubic Y₂O₂-ZrO₂ solid solution.     

Effect of Nd2O3 Concentration on the Defect Structure of CeO2–Nd2O3 Solid Solution

An extensive X-ray study of CeO₂–Nd₂O₃ solid solutions was performed, and the densities of solid solutions containing various concentrations of NdO_1.5 were measured using several techniques. Solid solutions containing 0–80 mol% NdO_1.5 were synthesized by coprecipitation from Ce(NO₃)₃ and Nd(NO₃)₃ aqueous solutions, and the coprecipitated samples were sintered at 1400°C. A fluorite structure was observed for CeO₂–NdO_1.5 solid solutions with 0–40 mol% NdO_1.5, which changed to a rare earth C-type structure at 45–75 mol% NdO_1.5. The change in the lattice parameters of CeO₂–NdO_1.5 solid solutions, when plotted with respect to the NdO_1.5 concentration, showed that the lattice parameters followed Vegard's law in both the fluorite and rare earth C-type regions. The maximum solubility limit for NdO_1.5 in CeO₂ solid solution was approximately 75 mol%. The relationship between the density and the Nd concentration indicated that the defect structure followed the anion vacancy model over the entire range (0–70 mol% NdO_1.5) of solid solution.     

SiO2/Fe2O3 Mesoporous Composite Prepared With an Activated Carbon Template in Supercritical Carbon Dioxide

SiO₂/Fe₂O₃ mesoporous composites have been prepared with a nanoscale casting process using an activated carbon (AC) template in supercritical carbon dioxide (SC CO₂). The composite precursor and acetone solvent (for Fe₂O₃ precursor) were dissolved in SC CO₂, and then coated on the AC in the desired supercritical condition. After removal of the AC template by calcinations in air at 600°C, SiO₂/Fe₂O₃ mesoporous composite were obtained. Temperature, pressure, and composite precursor ratio effects were studied. Scanning electron microscopy result shows that the porous structure of AC template had been well replicated by the composite product. Transmission electron micrograph indicates that nano iron oxides were well dispersed in the composite product.     

直接甲醇燃料电池技术及应用

本文回顾了直接甲醇燃料电池（ＤＭＦＣ）的研究开发历史,系统阐述了ＤＭＦＣ系统中电催化剂选择与设计基本原则、电解质膜材料与甲醇渗透的关系。分析了电池工作温度、工作压力和甲醇进料方式对ＤＭＦＣ电化学性能的影响。