Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

Ethylene dimerization over NiSO4 supported on Fe2O3-promoted ZrO2 catalyst

The NiSO₄ supported on Fe₂O₃-promoted ZrO₂ catalysts were prepared by the impregnation method. Fe₂O₃-promoted ZrO₂ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt.%, indicating good dispersion of nickel sulfate on the surface of Fe₂O₃–ZrO₂. The addition of nickel sulfate (or Fe₂O₃) to ZrO₂ shifted the phase transition of ZrO₂ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or Fe₂O₃) and ZrO₂. 15-NiSO₄/5-Fe₂O₃–ZrO₂ containing 15 wt.% NiSO₄ and 5 mol% Fe₂O₃, and calcined at 500 °C exhibited a maximum catalytic activity for ethylene dimerization. NiSO₄/Fe₂O₃–ZrO₂ catalysts was very effective for ethylene dimerization even at room temperature, but Fe₂O₃–ZrO₂ without NiSO₄ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of Fe₂O₃ up to 5 mol% enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between Fe₂O₃ and ZrO₂ and due to consequent formation of Fe–O–Zr bond.     

Coke study on MgO-promoted Ni/Al2O3 catalyst in combined H2O and CO2 reforming of methane for gas to liquid (GTL) process

MgO-promoted Ni/Al₂O₃ catalysts have been investigated with respect to catalytic activity and coke formation in combined steam and carbon dioxide reforming of methane (CSCRM) to develop a highly active and stable catalyst for gas to liquid (GTL) processes. Ni/Al₂O₃ catalysts were promoted through varying the MgO content by the incipient wetness method. X-ray diffraction (XRD), BET surface area, H₂-temperature programmed reduction (TPR), H₂-chemisorption and CO₂-temperature programmed desorption (TPD) were used to observe the characteristics of the prepared catalysts. The coke formation and amount in used catalysts were examined by SEM and TGA, respectively. H₂/CO ratio of 2 was achieved in CSCRM by controlling the feed H₂O/CO₂ ratio. The catalysts prepared with 20 wt.% MgO exhibit the highest catalytic performance and have high coke resistance in CSCRM. MgO promotion forms MgAl₂O₄ spinel phase, which is stable at high temperatures and effectively prevents coke formation by increasing the CO₂ adsorption due to the increase in base strength on the surface of catalyst.     

Hydrogenation of naphthalene on NiMo- Ni- and Ru/Al2O3 catalysts: Langmuir–Hinshelwood kinetic modelling

The importance of the hydrodearomatisation (HDA) is increasing together with tightening legislation of fuel quality and exhaust emissions. The present study focuses on hydrogenation (HYD) kinetics of the model aromatic compound naphthalene, found in typical diesel fraction, in n-hexadecane over a NiMo (nickel molybdenum), Ni (nickel) and Ru (ruthenium) supported on trilobe alumina (Al₂O₃) catalysts. Kinetic reaction expressions based on the mechanistic Langmuir–Hinshelwood (L–H) model were derived and tested by regressing the experimental data that translated the effect of both naphthalene and hydrogen concentration at a constant temperature (523.15 and 573.15 K over the NiMo catalyst and at 373.15 K over the Ni and Ru/Al₂O₃ catalysts) on the initial reaction rate. The L–H equation, giving an adequate fit to the experimental data with physically meaningful parameters, suggested a competitive adsorption between hydrogen and naphthalene over the presulphided NiMo catalyst and a non-competitive adsorption between these two reactants over the prereduced Ni and Ru/Al₂O₃ catalysts. In addition, the adsorption constant values indicated that the prereduced Ru catalyst was a much more active catalyst towards naphthalene HYD than the prereduced Ni/Al₂O₃ or the presulphided NiMo/Al₂O₃ catalyst.     

氧化石墨烯负载纳米Fe3O4类芬顿处理制药废水

采用改进Hummer法制备了氧化石墨烯(GO)负载纳米Fe₃O₄磁性催化剂(Fe₃O₄/GO),对其进行了X射线衍射仪、扫描电子显微镜和能量-色散光谱表征,并将其应用于多相类芬顿处理高浓化学原料药生产废水。结果表明,Fe₃O₄颗粒成功负载在GO表面,且没有出现明显的团聚现象。当废水的pH为3,双氧水(H₂O₂的质量分数30%)投加量10 mL/L,催化剂投加量2 g/L,反应120 min后COD去除率达78%,UV254去除率高达81%。三维荧光光(3D-EEM)分析可知,芳香类和富里酸类物质在催化降解过程中得到有效去除。     

Influence of the co-feeding of CO, H2, CO2 or H2O in the partial oxidation of methane over Ni and Rh supported catalysts

The influence of the addition of 5 vol.% of carbon monoxide, hydrogen, carbon dioxide or water to the feed of partial oxidation of methane was investigated over Ni/γ-Al₂O₃ and Rh/γ-Al₂O₃ catalysts. In addition to catalytic tests, thermodynamic calculations were performed to predict the effect of these gas co-feeds. Compared to the thermodynamic trends, differences in the influence of the co-feeding on catalytic performances were observed between both catalysts. Co-feeding of CO, H₂, CO₂ or H₂O can modify the oxidation state and dispersion of the metal component of the catalysts during reaction, and as a consequence, their performances. Changes in catalysts can be due to dynamic processes occurring during reaction. It is suggested to take these processes into account in a more complex kinetic equation for the reactions involved.     

Ni(OH)2修饰对a-Fe2O3薄膜光电化学性能的增强效应

利用一种简便的电沉积方法制备氧化铁薄膜,并在过程中引入Ni(OH)₂进行修饰,对具体电沉积实验参数进行优化,从而建立最佳制备条件。利用场发射扫描电子显微镜、X射线粉末衍射对Fe₂O₃/Ni(OH)₂光电极膜的结构进行表征。利用循环伏安和计时电流测量析氧过电位和光电流密度。结果表明,Ni(OH)₂修饰的α-Fe₂O₃薄膜可提高光生电子与空穴的分离效率,从而显著提高光电催化活性。     

Conversion of syn-gas to lower alkenes over Fe-TiO2-ZnO-K2O catalyst system

Conversion of syn-gas to lower alkenes is studied over a multicomponent catalyst system, Fe-TiO₂-ZnO-K₂O. Various reaction variables affecting the conversion were studied. At H₂:CO=1, 2.5 kg/cm² pressure, 250°C temperature and GHSV=960 h⁻¹, maximum selectivity of 68% to alkenes was obtained at 45% conversion of the feed. The alkenes consist of a mixture of propylene (65%) and ethylene (35%). The catalyst is active even after 200 h of use. The catalyst samples were characterised by BET surface area measurements, TPR and TPD. XRD and ESCA studies reveal the presence of Fe₂O₃ phase in the fresh catalyst. This phase is ably promoted by Zn and K. On reaction with CO+H₂, electron-rich species are formed on catalyst surface, which are the most likely active species. In addition to this, there is an improvement in dispersion of the active phase. These factors may contribute toward better performance of the catalyst in the conversion of syn-gas to lower alkenes.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

Coprecipitated iron-containing catalysts (Fe-Al2O3, Fe-Co-Al2O3, Fe-Ni-Al2O3) for methane decomposition at moderate temperatures: Part II. Evolution of the catalysts in reaction

Coprecipitated Fe-Al₂O₃, Fe-Co-Al₂O₃ and Fe-Ni-Al₂O₃ catalysts is shown to be very efficient in carbon deposition during methane decomposition at moderate temperatures (600–650 °C). The carbon capacity of the most efficient bimetallic catalysts containing 50–65 wt.% Fe, 5–10 wt.% Co (or Ni) and 25–40 wt.% Al₂O₃ is found to reach 145 g/g_cat. Most likely, their high efficiency is due to specific crystal structures of the metal particles and formation of optimum particle size distribution. According to the TEM data, catalytic filamentous carbon (CFC) is formed on them as multiwall carbon nanotubes (MWNTs). The phase composition of the catalysts during methane decomposition is studied using a complex of physicochemical methods (XRD, REDD, Mössbauer spectroscopy and EXAFS). Possible mechanisms of the catalyst deactivation are discussed.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Intensification of levofloxacin sono-degradation in a US/H2O2 system with Fe3O4 magnetic nanoparticles

Fe3O4 magnetic nanoparticles (MNPs) were synthesised, characterised, and used as a peroxidase mimetic to ac-celerate levofloxacin sono-degradation in an ultrasound (US)/H2O2 system. The Fe3O4 MNPs were in nanometre scale with an average diameter of approximately 12 to 18 nm. The introduction of Fe3O4 MNPs increased levofloxacin sono-degradation in the US/H2O2 system. Experimental parameters, such as Fe3O4 MNP dose, initial solution pH, and H2O2 concentration, were investigated by a one-factor-at-a-time approach. The results showed that Fe3O4 MNPs enhanced levofloxacin removal in the pH range from 4.0 to 9.0. Levofloxacin removal ratio in-creased with Fe3O4 MNP dose up to 1.0 g·L?1 and with H2O2 concentration until reaching the maximum. More-over, three main intermediate compounds were identified by HPLC with electrospray ionisation tandem mass spectrometry, and a possible degradation pathway was proposed. This study suggests that combination of H2O2, Fe3O4 MNPs and US is a good way to improve the degradation efficiency of antibiotics.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Catalytic conversion of methane and CO2 to synthesis gas over a La2O3-modified SiO2 supported Ni catalyst in fluidized-bed reactor

In this contribution, a commercial spherical SiO₂ was modified with different amounts of La₂O₃, and used as the support of Ni catalysts for autothermal reforming of methane in a fluidized-bed reactor. Nitrogen adsorption, XRD and H₂-TPR analysis indicated that La₂O₃-modified SiO₂ had higher surface area, strengthened interaction between Ni and support, and improved dispersion of Ni. CO₂-TPD found that La₂O₃ increased the alkalescence of SiO₂ and improved the activation of CO₂. Coking reaction (via both temperature-programmed surface reaction of CH₄ (CH₄-TPSR) and pulse decomposition of CH₄) disclosed that La₂O₃ reduced the dehydrogenation ability of Ni. CO₂-TPO, O₂-TPO (followed after CH₄-TPSR) confirmed that only part amount of carbon species derived from methane decomposition could be removed by CO₂, and O₂ in feed played a crucial role for the gasification of the inactive surface carbons. Ni/xLa₂O₃-SiO₂ (x = 10, 15, 30) possessed high activity and excellent stability for autothermal reforming of methane in a fluidized-bed reactor.     

柠檬酸钠改性的Fe3O4磁性纳米粒子的快速制备

以FeSO_4·7H_2O为单一铁源,浓氨水为沉淀剂,柠檬酸钠为表面改性剂利用简单回流法快速合成Fe_3O_4磁性纳米粒子。考察反应时间,反应温度及浓氨水加入方式对合成Fe_3O_4磁性纳米粒子的影响,并利用动态光散射仪、傅立叶红外射线光谱仪及透射扫描电镜等对合成的Fe_3O_4磁性纳米粒子进行表征。结果表明,以柠檬酸钠为表面改性剂,逐滴加入浓氨水,反应温度为(70～80)℃和反应时间为6 min时,获得的Fe_3O_4磁性纳米粒子在水中具有良好的分散性及磁响应性。Zeta电位和红外光谱同时表明,柠檬酸钠成功地吸附于Fe_3O_4磁性纳米粒子的表面(Fe_3O_4@SC),且Zeta电位值为-31.3 mV;透射扫描电镜显示获得的Fe_3O_4@SC磁性纳米粒子呈球状结构,粒径约为10 nm。     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Phenol hydroxylation using Fe-MCM-41 catalysts

Highly ordered iron-containing mesoporous material, Fe-MCM-41, with 0.5–4 Fe/Si mol% loading was prepared and characterization was performed using XRD, SEM/TEM, EDS, N₂-sorption, and FT-IR and UV–vis spectroscopies. Fe-MCM-41 exhibited high catalytic activity in phenol hydroxylation using H₂O₂ as oxidant, giving phenol conversion of ca. 60% at 50 °C [phenol:H₂O₂ = 1:1, water solvent]. Effects of Fe contents in Fe-MCM-41 and catalyst concentration, temperature, solvent used, phenol/H₂O₂ mole ratios and H₂O₂ feeding method, and catalyst calcination temperature on conversion profiles were examined. Catalyst recycling was performed to investigate the extent of potential metal leaching. Comparisons in performance were also made using nano-sized Fe₂O₃ particles and Fe-salt impregnated MCM-41 as catalyst. Catechol to hydroquinone in product ratio was close to 2:1 in accordance with a free radical reaction scheme involving Fe²⁺/Fe³⁺ redox pair and the larger amount of Fe species always achieved the given phenol conversion at a shorter reaction time. As the calcination temperature increases from 400 to 800 °C increasing amount of Fe species came out from the MCM-41 framework. Both tetrahedral Fe and extra-framework Fe species were found catalytically active, but high dispersion of Fe species achieved in Fe-MCM-41 was an advantage.     

Effects of small MoO3 additions on the properties of nickel catalysts for the steam reforming of hydrocarbons III. Reduction of Ni-Mo/Al2O3 catalysts

Ni/Al₂O₃ catalyst modified by small amounts of Mo show unusual properties in the steam reforming of hydrocarbons. There are no data about the effect of small amounts of molybdenum on reduction of the Ni-Mo supported catalysts. The properties of these very complex systems depend on the conditions of successive preparation stages (calcination, reduction) or the process conditions.

A series of Ni/Al₂O₃ catalysts modified by Mo were prepared in order to investigate the influence of promoter amounts and preparation sequence on their properties. Temperature programmed reduction (TPR) has been employed to study the reducibility of Ni-Mo/Al₂O₃ catalysts. Catalysts were further characterized by BET area, H₂ chemisorption and X-ray diffraction measurements.

The TPR curves of Ni-Mo/Al₂O₃ catalysts are very complex. Mo addition leads to the decrease of catalysts reducibility. However, complete reduction of NiO and MoO₃ can be achieved at 800 °C. The reduction course depends on the sequence of nickel and molybdenum addition into the support. Precise measurements of Ni peaks positions in the XRD pattern of Ni/Al₂O₃ and Ni-Mo/Al₂O₃ samples show the possibility of Ni-Mo solid solution formation.