Preparation and Characterization of High-Density PbO–Bi2O3–B2O3 Glasses

Transparent glasses with densities greater than 8 g/mL, which are resistant to nuclear radiation damage and can serve as a host for rare-earth scintillators, are being developed. Glasses in the PbO–Bi₂O₃ system are known to have some of the highest densities yet reported. In this study, a thorough reexamination of these glasses has been performed to examine their optical-transmission windows and densities. The observed glass-forming range found in this work agrees well with that reported in the literature. A minimum of ≅ 10 mol% B₂O₃ was required in some cases to vitrify the compositions. Glasses were examined in which the PbO:Bi₂O₃ ratios ranged from 10:90 to 90:10 with a maximum total B₂O₃ content of ≅50 mol%. Glasses with higher B₂O₃ contents were not examined because of the rapidly decreasing density with increasing B₂O₃ content. The densities of the glasses ranged from a low of 6.0 g/mL to a high of 8.1 g/mL. The highest densities were observed for glasses with the greatest PbO content. Ultraviolet/visible and infrared spectra were recorded for these glasses. The transmission window lies between ≅430 and 3850 nm. A systematic increase in the cutoff wavelength was found to occur with an increase in the density. Water-absorption peaks were found in the infrared spectra at ≅3000 nm.     

Multicomponent Glasses of GeO2 and Sb2O3 with Bi2O3, T12O, andlor PbO

Previous studies on glass formation involving GeO₂ with Bi₂O₃, TI₂O, and PbO were extended by the use of Sb₂O₃. Wide areas of glass formation occur in the systems GeO₂-PbO-Sb₂O₃ and GeO₂-Bi₂O₃-Sb₂O₃ at all but the lowest GeO₂ contents; the region of single-phase glasses in the system GeO₂-Tl₂O-Sb₂O₃ is severely restricted. Glasses were examined by powder X-ray diffraction, differential thermal analysis, thermomechanical analysis, and Archimedes'technique to obtain glass transition and crystallization exotherm temperatures, thermal expansion coefficients, and densities; these properties are presented in diagrams for the GeO₂-Sb₂O₃ binary and for two ternary systems. Based on calculated values of Δ_o,the waveleneth for zero material dispersion. and dM/dΔ . the material disiersion slope at Δ_o, compositions in these systems may be useful for the construction of ultralow-loss optical waveguides in the 3 to 4 μm region.     

Effect of Sb2O3 on Thermal Properties of Glasses in Bi2O3–B2O3–SiO2 System

Glasses with compositions 50Bi₂O₃– x Sb₂O₃–10B₂O₃–(40– x ) SiO₂ ( x =0, 1, 3, 5, 8, 10) have been prepared by conventional melt quench technique. Substitution of Sb₂O₃ for SiO₂ exerted an obvious effect on properties of glasses, especially, increased glass transition temperature ( T _g) and crystalline temperature ( T _c) greatly. Results of infrared transmission spectra attributed the effect to the formation of new bridging bonds of Sb–O–B and Sb–O–Si in glass network.     

Depolymerization of GeO2 and B2O3-GeO2 Network Glasses by Sb2O3

Binary Sb₂O₃-GeO₂ glasses containing 45 mol% Sb₂O₃ and ternary Sb₂O₃-B₂O₃-GeO₂ glasses containing 50 mol% GeO₂ were prepared. Their densities (volumes), refractive indices, and infrared spectra were determined, and their colors and high-temperature viscosities were estimated visually. Small amounts of Sb₂O₃ (∼10 mol%) appear to perturb neither the Ge-O-Ge network nor those B-O-Ge networks with small B/Ge ratios (∼0.2). The B-O-Ge networks with larger B/Ge ratios (∼1.0) depolymerize in the presence of even less Sb₂O₃. Amounts of Sb₂O₃ >10 mol% appear to depolymerize the Ge-O-Ge and Ge-O-B networks progressively, possibly with the formation of chains. A structurally sensitive ir isofrequency contour technique developed for ternary glass systems was applied successfully to these Sb₂O₃-B₂O₃-GeO₂ glasses. These contours can thus readily detect significant network depolymerization in the absence of the usual network modifiers.     

Properties and Structure of Glasses in the Systems M2O-In2O3-GeO2 (M = Li,Na,K)

The glass-forming regions in the ternary systems M₂O-In₂O₃-GeO₂ (M = Li,Na,K) were determined. The region in each of the three ternaries is less extensive than in either of the analogous systems M₂O-Al₂O₃-GeO₂ and M₂O-Ga₂O₃-GeO₂; this behavior reflects the restrictive coordination requirements of the larger In ion. The In₂O₃-containing glasses exhibit higher densities and refractive indices than the corresponding Al₂O₃ and Ga₂O₃-containing glasses. Refractive index and density maxima are observed along lines of constant In₂O₃ in each of the three alkali indogermanate systems.     

Eletrical Properties of Glasses in the System PbO-Al2O3-B2O3-SiO2

Glasses in the system Pb0–Al₂O₃-B₂O₃-SiO₂ are chemically stable over a wide composition range and have very desirable electrical characteristics such as high electrical resistivities and activation energies for conduction. Variations in these electrical properties were studied as a function of composition changes within the system, the object being to identify the role of the constituent oxides in achieving the highest activation energy and resistivity values consistent with moderate preparation temperatures. Measurements were made in the temperature range 25° to 400°C on carefully prepared glass disks in which the individual oxide components or different oxide ratios such as PbO/SiO₂, Al₂O₃/SiO₂, and B_sO₃/SiO₁ were systematically varied. The activation energy and resistivity values obtained ranged from 1.2 to 1.6 ev and 10° to 10¹⁴ ohm-cm, with dielectric constants ranging from 9 to 19 and densities from 4.30 to 4.50 g/cmY. Indications were that, for the composition range studied, the behavior manifested was basically that of the binary PbO-SO₂ glass with additions of Al₂O₃ or B₂O₃, even in small concentrations, sharply increasing the activation energy for conduction while lowering the density.     

The Series MgCr2O4-MgFe2O4

The characteristics of spinels in the series MgCr₂O₄-MgFe₂O₄ were determined. The plot of cell size vs. molar composition is unusual in series showing complete solid solution because an unusually large deviation from Vegard's law was observed. This deviation is caused by changes in spinel structure with composition and temperature, and an equation was derived which applies a correction in terms of the degree of inversion. The effects of temperature on compositions high in MgFe₂O₄ include changes in density and refractive index. Solid solution of forsterite in MgCr₂O₄ decreases the cell size to 8.329 A but apparently is less than 1%. Changes in composition caused by vapor loss or by dissociation are small enough that this series is essentially binary below 1400° C.     

Stable and Metastable Equilibria in the Systems Y2O2-Al2O3, and Gd2O3-Fe2O3

The phase equilibrium relations in the systems Y₂O₃-Al₂O₃ and Gd₂O₃-Fe₂O₃ were examined. Each system has two stable binary compounds. A 3:s molar ratio garnet-type compound exists in both systems. The 1:1 distorted perovskite structure is stable in the system Gd₂O₃-Fe₂O₃ but only metastable in the system Y₂O₃-AI₂O₃. This interesting example of metastable formation and persistence of a compound with ions of high Z/r values explains the discrepancies in the literature on the structure of the composition YA1O₃. A new 2:1 molar ratio cubic phase has been found in the system Y₂O₃-A1₂O₃. Since silicon can be completely substituted for aluminum in this compound, the aluminum ions are presumably in fourfold coordination.     

Physical Properties and Structure of rf-Sputtered Amorphous Films in the System Al2O3–Y2O3

Amorphous films in the system Al₂O₃–Y₂O₃ were prepared by the rf sputtering method in the range of 0–76 mol% Y₂O₃, and their density, refractive index, and elastic constants were measured. All of the physical properties of the amorphous Al₂O₃–Y₂O₃ films had a similar compositional dependence; that is, they increased continuously, but not linearly with increasing Y₂O₃ content. To confirm the coordination states of aluminum and yttrium ions in the amorphous Al₂O₃–Y₂O₃ films, the Al K α X-ray emission spectra and the X-ray absorption near edge structures (XANES) were measured. The average coordination number of aluminum ions in the amorphous films containing up to about 40 mol% Y₂O₃ content was 5, that is a mixture of 4-fold- and 6-fold-coordinated states. In the region of more than about 50 mol% Y₂O₃, the fraction of the 6-fold-coordinated aluminum ions increased with increasing Y₂O₃ content, while the results led to the conclusion that the coordination number of yttrium ions was always 6, regardless of composition. These results indicate that, in amorphous films in the system Al₂O₃–Y₂O₃, the change of the coordination state of aluminum ions has an important effect on physical properties.     

Properties of Sm2O3─Al2O3─SiO2 Glasses for In Vivo Applications

The compositional range for glass formation below 1600°C in the Sm₂O₃─Al₂O₃─SiO₂ system is (9–25)Sm₂O₃─(10–35)Al₂O₃─(40–75)SiO₂ (mol%). Selected properties of the Sm₂O₃─Al₂O₃─SiO₂ (SmAS) glasses were evaluated as a function of composition. The density, refractive index, microhardness, and thermal expansion coefficient increased as the Sm₂O₃ content increased from 9 to 25 mol%, the values exceeding those for fused silica. The dissolution rate in 1 N HCl and in deionized water increased with increasing Sm₂O₃ content and with increasing temperature to 70°C. The transformation temperature ( T _g ) and dilatometric softening temperature ( T _d ) of the SmAS glasses exceeded 800° and 850°C, respectively.     

Phases in the Binary Systems PbO—La2O3, Gd2O3, and Sm2O3

In the binary system PbO–La_zO₃ only one compound, 4PbO.La₂O₃, exists; it is flanked by two eutectics. The structure of the compound, although of lower symmetry, is intimately related to the C modification of the rare earths. Below 800° to 1000°C, metastable solid solutions are formed from oxide mixtures coprecipitated from mixed solutions of the nitrates, the cubic parameter a = 5.66 A, if extrapolated to pure La₂O₃, corresponding to half the a parameter of the C form of La₂O₃. The solid solutions existing between the compositions La₂O₃–2Pb0 and pure La₂O₃ have a cubic face–centered lattice and obey Vegard's rule. The systems of PbO with Sm₂O₃ and Gd₂O₈ are quite similar to that with La₂O₃. The compound Sm₂O₃.4Pb0 decomposes at 1000°C with evaporation of PbO; Sm₂O₃ remains in the B modification.     

The System HfO2-Y2O3-Er2O3

A mathematical model of the liquidus surface based on a reduced polynomial method was proposed for the system HfO₂-Y₂O₃-Er₂O₃. The results of calculations according to this model agree fairly well with the experimental data. Phase equilibria in the system HfO₂-Y₂O₃-Er₂O₃ were studied on melted (as-cast) and annealed samples using X-ray diffraction (at room and high temperatures) and micro-structural and petrographic analyses. The crystallization paths in the system HfO₂-Y₂O₃-Er₂O₃ were established. The system HfO₂-Y₂O₃-Er₂O₃ is characterized by the formation of extended solid solutions based on the fluorite-type (F) form of HfO₂ and cubic (C) and hexagonal (H) forms of Y₂O₃ and Er₂O₃. The boundary curves of these solid solutions have the minima at 2370°C (15. 5 mol% HfO₂, 49. 5 mol% Y₂O₃) and 2360°C (10. 5 mol% HfO₂, 45. 5 mol% Y₂O₃). No compounds were found to exist in the system investigated.     

Properties and Structure of Glasses in the System Bi2O3-SiO2-GeO2

In the system Bi₂O₃-SiO₂-GeO₂, good glasses can be formed only from limited compositional regions consisting of 2 narrow strips along the lines x Bi₂O₃-(100-:t) GeO₂ ( x ≤40) and 40Bi₂O₃ y SiO₂ (60- y )GeO₂ (mol%); such glass is dark brown. Compositions from a large region (Bi₂O₃ content <40 mol%) showed immiscibility. In the binary system Bi₂O₃-GeO₂, density and refractive index vary linearly with composition (mol%). Negative deviations of molar volume from ideality suggest that the coordination of a significant number of Ge ions is changing from 4-fold to 6-fold. Thermal expansion and electrical resistivity data are also reported.     

Structure, Thermal Behavior, Chemical Durability, and Optical Properties of the Na2O–Al2O3–TiO2–Nb2O5–P2O5 Glass System

The FTIR, Raman, UV-Vis, ³¹P MAS-NMR, DTA, and refractive index measurements have been combined to investigate a series of glasses with the general formula 20Na₂O–5Al₂O₃− x TiO₂–(45− x )Nb₂O₅–30P₂O₅, 15≤ x ≤45. The glass structure, as well as thermal, optical, and chemical durability properties, were then described as functions of the f _Nb/ f _Ti ratio. An increase of the f _Nb/ f _Ti ratio correlates with a decrease in length of the average phosphate chains linked through Nb–O–P and Ti–O–P bonds, with an increase in the glass stability and with increase in the linear refractive indices at 632.8 nm from 1.79 to 1.89. Furthermore, niobium is more effective than titanium in improving chemical durability.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Wet Milling of Fe/Al/Al2O3 and Fe2O3/Al/Al2O3 Powder Mixtures

Wet milling of Al₂O₃-aluminide alloy (3A) precursor powders in acetone has been investigated by milling Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixtures. The influence of the milling process on the physical and chemical properties of the milled powders has been studied. Particle refinement and homogenization were found not to play a dominant role, whereas plastic deformation of the metal particles leads to the formation of dislocations and a highly disarranged polycrystalline structure. Although no chemical reactions among the powder components in Fe₂O₃/Al/Al₂O₃ powder mixtures were observed, the formation of a nanocrystalline, ordered intermetallic FeAl phase in Fe/Al/Al₂O₃ powder mixtures caused by mechanical alloying was detected. Chemical reactions of Fe and Al particle surfaces with the atmosphere and the milling media lead to the formation of highly porous hydroxides on the particle surfaces. Hence the specific surface area of the powders increases, while the powder density decreases during milling. The fraction of Fe oxidized during milling was determined to be 0.13. The fraction of Al oxidized during milling strongly depends on the metal content of the powder mixture. It ranges between 0.4 and 0.8.     

The System CaO-Ga2O3

CaO and Ga₂O₃ form three compounds: 3CaO-Ga₂O₃, CaO-Ga₂O₃, and CaO-2Ga₂O₃. 3CaO-Ga₂O₃ melts incongruently to CaO plus liquid at 1263°C.; CaO Ga₂O₃ and CaO 2Ga₂O₃ melt congruently at 1369° and 1504°C. respectively. Eutectics are located at the following temperatures and compositions (in mole% Ga₂O₃): between 3CaO Ga₂O₃ and CaO Ga₂O₃, 1245°C. and 37.5%; between CaO Ga₂O₃ and CaO-2Ga₂O₃,1323^oC. and 57.0%; and between CaO -2Ga₂O₃ and β-Ga₂O₃,1457°C. and 68.0%. There is a peritectic at 1263°C. and 36.0%. Three polymorphs of CaO Ga₂O₃ are described. Compositions from approximately 35 to 70 mole% Ga₂O₃ can be quenched to yield homogeneous glasses.     

Kinetics of Solid-State Reaction of Bi2O3 and Fe2O3

Solid-state reactions of equimolar mixtures of Bi₂O₃ and Fe₂O₃ from 625° to 830°C and their kinetics were investigated. The reaction rates were determined from the integrated X-ray diffraction intensities of the strongest peaks of the reactants and products. The activation energy for the formation of BiFeO₃ was 96.6±9.0 kcal/mol; that for a second-phase compound, Bi₂Fe₄O₉, which formed above 675°C, was 99.4±9.0 kcal/mol. Specific rate constants for these simultaneous reactions were obtained. The preparation of single-phase BiFeO₃ from the stoichiometric mixture of Bi₂O₃ and Fe₂O₃ is discussed.     

Thermodynamic Modeling of the Isomorphous Phase Diagrams in the Al2O3–Cr2O3 and V2O3–Cr2O3 Systems

The phase diagrams in the Al₂O₃–Cr₂O₃ and V₂O₃–Cr₂O₃ systems have been assessed by thermodynamic modeling with existing data from the literature. While the regular and subregular solution models were used in the Al₂O₃–Cr₂O₃ system to represent the Gibbs free energies of the liquid and solid phases, respectively, the regular solution model was applied to both phases in the V₂O₃–Cr₂O₃ system. By using the liquidus, solidus, and/or miscibility gap data, the interaction parameters of the liquid and solid phases were optimized through a multiple linear regression method. The phase diagrams calculated from these models are in good agreement with experimental data. Also, the solid miscibility gap and chemical spinodal in the V₂O₃–Cr₂O₃ system were estimated.     

Spectrum of Volume Relaxation Times in B2O3

Time-index of refraction isotherms were measured for B₂O₃ glass starting from both a high and a low temperature in the transformation region. The equilibrium index values at each temperature, obtained from both types of approach curve, were identical. As in the case of the density values, the equilibrium refractive index curve as a function of temperature for this glass is not a straight line. The two-relaxation-times (crossover) model was applied to B₂O₃ glass and fitted the data as well as it did in previous experiments with borosilicate crown and GeO₂ glasses. The reverse crossover which was predicted by the model was experimentally confirmed with the B₂O₃ glass. The spectrum of relaxation times narrowed with decreasing temperature, indicating approach to another region of single relaxation associated with the low-temperature Arrhenius region. The relaxation times for the low-temperature crossover agreed well with those from the high-temperature curves, indicating complete linearity in the experiments. The spectrum of relaxation times was slightly asymmetrical at constant pressure and very asymmetrical at constant volume.