新型Ku频段全向微带阵列天线

设计了一种新型Ku频段全向天线,该天线由双面辐射微带阵列组成,通过串联形式馈电,实现了全向中等增益辐射特性.文中给出了微带阵列天线的设计方法,对该微带阵列天线的阻抗带宽特性、方向图特性和馈电结构进行了分析.结果表明,该微带阵列天线反射损耗小于-10 dB的绝对带宽为1.15 GHz,在可用频带内全向增益为6.8 dB～7.3 dB,E 面波束宽度在20°～24°,H面方向图不圆度在±0.5 dB以内.该天线能够满足微波通信系统要求.     

伞形印刷偶极子天线设计

针对数字阵列雷达设计了一种伞形印刷偶板子天线单元.该天线由微带集成巴伦馈电,具有宽频带、宽波束、易于集成等优点.通过仿真和测试,表明该天线有40％的相对带宽,E面波束宽度为80°,H面波束宽度为135°.     

一种宽带双极化波导阵列天线的设计

设计了一种适用于雷达、通信等领域的宽带双极化波导阵列天线。天线的垂直极化信号通过波导阻抗变换直接馈电实现,水平极化信号通过由垂直极化信号馈电、缝隙耦合的方式实现。设计的阵列天线在12 GHz～15 GHz的频带内驻波比小于2,交叉极化低于25 dB,单元增益在带内大于8 dB,波束宽度大于60°。加工天线后实测结果与仿真结果吻合,该种阵列天线既适合固定波束阵列天线,又适合具有相扫功能的阵列天线。     

低互耦星载相控阵天线设计

介绍了一款工作于Ku频段的低互耦星载相控阵天线的设计方法, 采用在阵列单元周围加载金属腔体的方式降低阵列单元之间的互耦效应, 从而改善相控阵天线的方向图扫描特性.针对相控阵天线在二维±60°范围内低副瓣波束扫描的特点, 对5×5子阵和16×16阵列进行了研究, 验证了阵列的互耦降低方法的有效性和电性能.研究结果表明:相控阵单元间互耦小于-16 dB, 而相控阵单元在15.1~16.8 GHz电压驻波比小于2, 相对带宽11%;在频率为f₀±500 MHz范围内, E面3 dB波束宽度大于98°, 5 dB波束宽度大于113°, H面3 dB波束宽度大于113°, 5 dB波束宽度大于122°.在仿真设计的基础上, 研制了子阵天线试验样机, 测试结果与设计结果吻合良好, 证明了降低互耦方法的有效性, 天线单元方向图满足在±60°范围内波束扫描的要求, 可应用于相控阵雷达系统.     

双层宽波束天线设计

针对宽波束天线在车载雷达中的应用,突破角雷达方位面3 dB波束宽度的限制,实现微带阵列天线在水平面的宽波束覆盖,设计了一款1×10串馈微带双层结构天线。线阵单元采用道尔夫-切比雪夫（Dolf-Chebyshev）综合法电流分布来达到降低天线俯仰面副瓣的效果,在串馈阵列上方加载寄生贴片和介质基板拓展天线方位面的3 dB波束宽度。分析了双层天线展宽波束的原理,加工并实测了双层宽波束天线,其方位面的3 dB波束宽度为134.6°,增益达到10.6 dB,副瓣电平为-19.8 dB,可以满足车载角雷达天线需求。     

用于空间功率合成的线阵馈电焦散抛物曲面天线

提出了一种用于空间功率合成的焦散抛物曲面天线,该反射面天线是由xoz平面的一条抛物线沿着yoz平面上的另一条抛物线正交扫描所形成的,天线用8单元E面喇叭线阵进行偏馈。研究了天线的反射面结构参数对天线性能的影响以及横向偏焦电扫描特性,给出了不同辐射方向下阵列的相位配置公式。仿真和实验结果表明:提出的方案可以在给定方向合成高增益波束,与同样线阵馈电的抛物柱面天线相比,H面3dB波束宽度从8.2°下降到了5°,天线增益提高了2.2dB.     

毫米波微带天线阵列设计

设计了一个圆口径串并联混合馈电的毫米波微带天线阵列。该天线采用矩形微带工字型缝隙贴片耦合馈电的方法展宽带宽。为了有效利用天线口径面积,减小网络复杂度,选取串联微带天线阵列形式。同时为了展宽带宽,根据设计的圆形口径阵列,将部分子阵采用串并联混合馈电的形式,得到带宽为5%的毫米波微带天线阵列。仿真表明,该天线在工作频带内增益大于30.6 d Bi,波束宽度为4.0°×3.5°,副瓣电平低于–13 d B。该天线阵面与网络配合,可以实现多波束或相控阵的功能。     

基于口面场方法的W波段高口面效率单脉冲卡塞格伦天线（英文）

提出来一种应用于直升机防撞雷达的高口面效率W波段单脉冲双反射面卡塞格伦天线.口面分析方法的提出解决了W波段反射面天线口面相位分布不均匀的缺陷,从而有效地提高了口面的利用效率.利用该方法,本文研究并制作了口径为135 mm、焦距为40.5 mm的W波段卡赛格伦天线,并且设计了由四个E面多缝隙电桥和四个四分之一波导波长延迟线级联构成的和差网络.经测试,该单脉冲天线在93 GHz具有38.6 dBi的和波束增益,相应的口面效率为54.7%;差波束的零深优于-22 dB,副瓣电平小于-18 dB.测试结果与基于口面分析方法的仿真结果吻合,从而证明了本文所研究天线可以应用于高口面效率的W波段单脉冲系统中.     

一种毫米波宽带宽波束双极化微带天线

针对宽波束天线在5G毫米波宽角扫描阵列的应用,设计了一款基于接地金属柱的毫米波双极化微带天线单元。该天线具有低剖面、宽带、宽波束等优点。天线采用双“H”型缝隙耦合馈电,通过寄生贴片与开槽基板共同辐射展宽波束宽度,通过调节接地金属柱结构改变输入阻抗展宽阻抗带宽。实测结果表明,该天线的3 dB波束宽度在24.5～27.5 GHz的频带内(电压驻波比小于1.8)均大于130°,交叉极化比大于18 dB,两个端口之间的隔离度在频带内均高于26 dB。测试结果与仿真结果吻合较好。     

一种串联馈电式Vivaldi阵列天线

设计了一款串馈式Vivaldi阵列天线,天线由12个相同的Vivaldi构成辐射源,由串联馈电式功分馈电网络进行馈电,通过调整每个节点的功分比,使Vivaldi天线单元的馈电幅度呈泰勒加权分布,从而降低天线旁瓣。仿真结果表明,所设计天线阵列在中心频点处驻波比系数小于1.5,天线方向图3-dB波束宽度为7.35°,最大旁瓣小于-23.8 dB,交叉极化低于-41.5dB,天线增益为15.0 dBi。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.