Microstructural development of Sn-Ag-Cu solder joints

The effects of Cu as pad material and of the metallization of pad (with Sn) and component (with Ni) on the evolving microstructure of lead-free solder joints were studied. A solder paste with composition 95.5wt.%Sn-4.0wt.%Ag-0.5wt.%Cu was used. Partial dissolution of the Cu substrate led to a change in the overall composition of the solder, which caused a precipitation morphology different from the one expected regarding the initial composition. Kinetics of growth of the Cu₆Sn₅ phase, as particles in the bulk of the solder and as a reaction layer adjacent to the Cu pad, was studied in the temperature range 125–175°C.     

Recent advances on kinetic analysis of electromigration enhanced intermetallic growth and damage formation in Pb-free solder joints

A comprehensive kinetic analysis was established to investigate the electromigration (EM) enhanced intermetallic compound (IMC) growth and void formation for Sn-based Pb-free solder joints with Cu under bump metallization (UBM). The kinetic model takes into account Cu-Sn interdiffusion and current stressing. Derivation of the diffusion coefficients and the effective charge numbers for the intermetallic compounds is an essential but challenging task for the study of this multi-phase multi-component intermetallic system. A new approach was developed to simultaneously derive atomic diffusivities and effective charge numbers based on simulated annealing (SA) in conjunction with the kinetic model. A consistent set of parameters were obtained, which provided important insight into the diffusion behaviors driving the IMC growth. The parameters were used in a finite difference model to numerically solve the IMC growth problem and the result accurately correlated with the experiment. EM reliability test revealed that the ultimate failure of the solder joints was caused by extensive void formation and subsequent crack propagation at the intermetallic interface. This damage formation mechanism was analyzed by first considering vacancy transport under current stressing. This was followed by a finite element analysis on the crack driving force induced by void formation. This paper is concluded with a future perspective on applying the kinetic analysis and damage mechanism developed to investigate the structural reliability of the through-Si-via in 3D interconnects.     

Microstructures and degradation of heat sink very-thin quad flat package no-leads Pb-free Sn-Ag-Cu solder joints after thermal aging

Heat sink very-thin quad flat package no-leads (HVQFN) packages soldered with Sn-3.8Ag-0.7Cu on metallized laminate substrates have been put to thermal aging. Temperatures from 140°C to 200°C for times up to 30 weeks were applied. The solder joint microstructure develops intermetallic compound layers and voids within the solder. Due to this, the mechanical reliability of the HVQFN inner lead solder joints is degraded. The intermetallic layers are of the type (Cu, Y)₆Sn₅, with Y=Ni, Au or Ni+Au, as well as Cu₃Sn, and follow a power law with aging time: X=C·tⁿ, where n=0.4 to 1.9 depending on temperature. The voids within the solder are attributed to Sn depletion of the solder in favor of the growth of (Cu,Ni)₆Sn₅. They are more pronounced the less the solder volume is in proportion to the intermetallic diffusion area. The amount of voids is quantified as a percentage of the residual solder. The time to reach the failure criterion of 50%, i.e., t_50%, is related to the absolute temperature according to an Arrhenius equation with an activation energy E_a=0.95 eV. This equation is used for determination of the maximum allowable temperature at a certain required operating lifetime.     

Phase equilibria and the related properties of Sn-Ag-Cu based Pb-free solder alloys

We have recently developed a thermodynamic database for micro-soldering alloys which consists of the elements Pb, Bi, Sn, Sb, Cu, Ag, Zn, and In. In this paper, the phase equilibria and the related thermodynamic properties of the Sn-Ag-Cu base alloys are presented using this database, alloy systems being one of the promising candidates for Pb-free solders. The isothermal section diagrams of the Sn-Ag-Cu ternary system were experimentally determined by SEM-EDS, x-ray diffraction and metallographic techniques. Based on the present results as well as the previous data on phase boundaries and thermochemical properties, thermodynamic assessment of this system was carried out. The isothermal and vertical section diagrams, liquidus surface, mass fractions of the phase constitution, etc., were calculated. The predictions of surface energy and viscosity were also investigated. Moreover, a non-equilibrium solidification process using the Scheil model was simulated and compared with the equilibrium solidification behavior in some Sn-Ag-Cu base alloys. Calculated results based on the Scheil model were incorporated into a three-dimensional solidification simulation and the prediction of practical solidification procedures was performed.     

Mode I fracture toughness testing of eutectic Sn-Pb solder joints

The mode I plane strain fracture toughness of Cu/63Sn-37Pb solder joints was measured using a technique based upon the ASTM standard methods for fracture toughness testing. A solder joint compact tension sample geometry was selected for the evaluation and each sample was manufactured using a capillary soldering system that provides excellent control over critical processing parameters. The mode I plane strain fracture toughness based on these tests is 8.36 MPa√m. Failure is dominated by microvoid nucleation in the solder and fracture of the intermetallic particles that are located at the solder/copper interface. The validity of the testing method used and the relevance of the results to solder joint reliability are discussed.     

Rate-dependent properties of Sn-Ag-Cu based lead-free solder joints for WLCSP

The increasing demand for portable electronics has led to the shrinking in size of electronic components and solder joint dimensions. The industry also made a transition towards the adoption of lead-free solder alloys, commonly based around the Sn-Ag-Cu alloys. As knowledge of the processes and operational reliability of these lead-free solder joints (used especially in advanced packages) is limited, it has become a major concern to characterise the mechanical performance of these interconnects amid the greater push for greener electronics by the European Union.In this study, bulk solder tensile tests were performed to characterise the mechanical properties of SAC 105 (Sn-1%wt Ag-0.5%wt Cu) and SAC 405 (Sn-4%wt Ag-0.5%wt Cu) at strain rates ranging from 0.0088 s⁻¹ to 57.0 s⁻¹. Solder joint array shear and tensile tests were also conducted on wafer-level chip scale package (WLCSP) specimens of different solder alloy materials under two test rates of 0.5 mm/s (2.27 s⁻¹) and 5 mm/s (22.73 s⁻¹). These WLCSP packages have an array of 12 × 12 solder bumps (300 μm in diameter); and double redistribution layers with a Ti/Cu/Ni/Au under-bump metallurgy (UBM) as their silicon-based interface structure.The bulk solder tensile tests show that Sn-Ag-Cu alloys exhibit higher mechanical strength (yield stress and ultimate tensile strength) with increasing strain rate. A rate-dependent model of yield stress and ultimate tensile strength (UTS) was developed based on the test results. Good mechanical performance of package pull-tests at high strain rates is often correlated to a higher percentage of bulk solder failures than interface failures in solder joints. The solder joint array tests show that for higher test rates and Ag content, there are less bulk solder failures and more interface failures. Correspondingly, the average solder joint strength, peak load and ductility also decrease under higher test rate and Ag content. The solder joint results relate closely to the higher rate sensitivity of SAC 405 in gaining material strength which might prove detrimental to solder joint interfaces that are less rate sensitive. In addition, specimens under shear yielded more bulk solder failures, higher average solder joint strength and ductility than specimens under tension.     

Board-level reliability of Pb-free solder joints of TSOP and various CSPs

To evaluate various Pb-free solder systems for leaded package, thin small outline packages (TSOPs) and chip scale packages (CSPs) including leadframe CSP (LFCSP), fine pitch BGA (FBGA), and wafer level CSP (WLCSP) were characterized in terms of board level and mechanical solder joint reliability. For board level solder joint reliability test of TSOPs, daisy chain samples having pure-Sn were prepared and placed on daisy chain printed circuit board (PCB) with Pb-free solder pastes. For CSPs, the same composition of Pb-free solder balls and solder pastes were used for assembly of daisy chain PCB. The samples were subjected to temperature cycle (T/C) tests (-65/spl deg/C/spl sim/150/spl deg/C, -55/spl deg/C/spl sim/125/spl deg/C, 2 cycles/h). Solder joint lifetime was electrically monitored by resistance measurement and the metallurgical characteristics of solder joint were analyzed by microstructural observation on a cross-section sample. In addition, mechanical tests including shock test, variable frequency vibration test, and four point twisting test were carried out with daisy chain packages too. In order to compare the effect of Pb-free solders with those of Sn-Pb solder, Sn-Pb solder balls and solder paste were included. According to this paper, most Pb-free solder systems were compatible with the conventional Sn-Pb solder with respect to board level and mechanical solder joint reliability. For application of Pb-free solder to WLCSP, Cu diffusion barrier layer is required to block the excessive Cu diffusion, which induced Cu trace failure.     

Microstructural modifications and properties of Sn-Ag-Cu solder joints induced by alloying

Slow cooling (1–3°C/sec) of Sn-Ag-Cu and Sn-Ag-Cu-X (X = Fe, Co) solder-joint specimens, made by hand soldering, simulated reflow in a surface-mount assembly to achieve similar as-solidified joint microstructures for realistic shear-strength testing, using Sn-3.5Ag (wt.%) as a baseline. Consistent with predictions from a recent Sn-Ag-Cu ternary phase-diagram study, either Sn dendrites, Ag₃Sn primary phase, or Cu₆Sn₅ primary phase were formed during solidification of joint samples made from the selected near-eutectic Sn-Ag-Cu alloys. Minor substitution of Co for Cu in Sn-3.7Ag-0.9Cu refined the joint-matrix microstructure by an apparent catalysis effect on the Cu₆Sn₅ phase, whereas Fe substitution promoted extreme refinement of the Sn-dendritic phase. Ambient-temperature shear strength was reduced by Sn dendrites in the joint microstructure, especially coarse dendrites in solute poor Sn-Ag-Cu, e.g., Sn-3.0Ag-0.5Cu, while Sn-3.7Ag-0.9Cu with Co and Fe additions have increased shear strength. At elevated (150°C) temperature, no significant difference exists between the maximum shear-strength values of all of the alloys studied.     

Interfacial reactions and shear strengths between Sn-Ag-based Pb-free solder balls and Au/EN/Cu metallization

The morphological and compositional evolutions of intermetallic compounds (IMCs) formed at three Pb-free solder/electroless Ni-P interface were investigated with respect to the solder compositions and reflow times. The three Pb-free solder alloys were Sn3.5Ag, Sn3.5Ag0.75Cu, and Sn3Ag6Bi2In (in wt.%). After reflow reaction, three distinctive layers, Ni₃Sn₄ (or Ni-Cu-Sn for Sn3.5Ag0.75Cu solder), NiSnP, and Ni₃P, were formed on the electroless Ni-P layer in all the solder alloys. For the Sn3.5Ag0.75Cu solder, with increasing reflow time, the interfacial intermetallics switched from (Cu,Ni)₆Sn₅ to (Cu,Ni)₆Sn₅+(Ni,Cu)₃Sn₄, and then to (Ni,Cu)₃Sn₄ IMCs. The degree of IMC spalling for the Sn3.5Ag0.75Cu solder joint was more than that of other solders. In the cases of the Sn3.5Ag and Sn3Ag6Bi2In solder joints, the growth rate of the Ni₃P layer was similar because these two type solder joints had a similar interfacial reaction. On the other hand, for the Sn3.5Ag0.75Cu solder, the thickness of the Ni₃P and Ni-Sn-P layers depended on the degree of IMC spalling. Also, the shear strength showed various characteristics depending on the solder alloys and reflow times. The fractures mainly occurred at the interfaces of Ni₃Sn₄/Ni-Sn-P and solder/Ni₃Sn₄.     

Interfacial microstructure of Pb-free and Pb-Sn solder balls in the ball-grid array package

Ball-grid array (BGA) samples were aged at 155°C up to 45 days. The formation and the growth of the intermetallic phases at the solder joints were investigated. The alloy compositions of solder balls included Sn-3.5Ag-0.7Cu, Sn-1.0Ag-0.7Cu, and 63Sn-37Pb. The solder-ball pads were a copper substrate with an Au/Ni surface finish. Microstructural analysis was carried out by electron microprobe. The results show that a ternary phase, (Au,Ni)Sn₄, formed with Ni₃Sn₄ in the 63Sn-37Pb solder alloy and that a quaternary intermetallic phase, (Au,Ni)₂Cu₃Sn₅, formed in the Sn-Ag-Cu solder alloys. The formation mechanism of intermetallic phases was associated with the driving force for Au and Cu atoms to migrate toward the interface during aging.     

Interfacial reaction and mechanical reliability of PTH solder joints with different solder/surface finish combinations

The effects of minor Ni addition (0.05 wt.%) on the microstructures and mechanical reliability of the lead-free solder joints used in the pin through hole (PTH) components were carefully investigated using a scanning electron microscope (SEM), a field-emission electron probe x-ray microanalyzer, and a pull tester. The PTH walls (i.e., Cu) of printed circuit boards (PCBs) were coated with organic solderability preservative (OSP) or electroless nickel/immersion gold (ENIG) surface finish before soldering. During soldering, the pins of the electronic components were first inserted into the PTHs deposited with OSP or ENIG, and then joined using a Sn–3Ag–0.5Cu (SAC) solder bath through a typical wave-soldering process. After wave soldering, a rework (the second wave soldering) was performed, where an SAC or Sn–0.7Cu–0.05Ni (SCN) solder bath was employed. The SCN joints were found to possess a higher tensile strength than the SAC ones in the OSP case. The sluggish growth of Cu₃Sn, along with few Kirkendall voids at the solder/Cu interface caused by minor Ni addition into the solder alloy (i.e., SCN), was believed to be the root cause responsible for the increase in the strength value. However, the mechanical strength of the PTH components was revealed to be insensitive to the solder composition in the alternative case where an ENIG was deposited over the PTH walls. The implication of this study revealed that minor addition of Ni into the solder is beneficial for the solder/Cu joints, but for the solder/Ni(P) joints.     

The growth of intermetallic compounds at Sn-Ag-Cu solder/Cu and Sn-Ag-Cu solder/Ni interfaces and the associated evolution of the solder microstructure

The evolution of intermetallics at and near SnAgCu/Cu and SnAgCu/Ni interfaces was examined, and compared to the behavior, near PbSn/metal and Sn/metal interfaces. Two different solder compositions were considered, Sn_93.6Ag_4.7Cu_1.7 and Sn_95.5Ag_3.5Cu_1.0 (Sn_91.8Ag_5.1 Cu_3.1 and Sn_94.35Ag_3.8Cu_1.85 in atomic percent). In both cases, phase formation and growth at interfaces with Cu were very similar to those commonly observed for eutectic SnPb solder. However, the evolution of intermetallics at SnAgCu/Ni interfaces proved much more complex. The presence of the Cu in the solder dramatically altered the phase selectivity at the solder/Ni interface and affected the growth kinetics of intermetallics. As long as sufficient Cu was available, it would combine with Ni and Sn to form (Cu,Ni)₆)Sn₅ which grew instead of the Ni₃Sn₄ usually observed in PbSn/Ni and Sn/Ni diffusion couples. This growing phase would, however, eventually consume essentially all of the available Cu in the solder. Because the mechanical properties of Sn-Ag-Cu alloys, depend upon the Cu content, this consumption can be expected to alter the mechanical properties of these Pb-free solderjoints. After depletion of the Cu from the solder, further annealing then gradually transformed the (Cu,Ni)₆Sn₅ phase into a (Ni,Cu)₃Sn₄ phase.     

Mechanical properties of intermetallic compounds associated with Pb-free solder joints using nanoindentation

Mechanical properties of intermetallic compound (IMC) phases in Pb-free solder joints were obtained using nanoindentation testing (NIT). The elastic modulus and hardness were determined for IMC phases associated with insitu FeSn particle reinforced and mechanically added, Cu particle-reinforced, composite solder joints. The IMC layers that formed around Cu particle reinforcement and at the Cu substrate/solder matrix interface were probed with NIT. Moduli and hardness values obtained by NIT revealed were noticeably higher for Cu-rich Cu₃Sn than those of Cu₆Sn₅. The Ag₃Sn platelets that formed during reflow were also examined for eutectic Sn-Ag solder column joints. The indentation modulus of Ag₃Sn platelets was significantly lower than that of FeSn, SnCuNi, and CuSn IMCs. Indentation creep properties were assessed in localized microstructure regions of the as-cast, eutectic Sn-Ag solder. The stress exponent, n, associated with secondary creep differed widely depending on the microstructure feature probed by the indenter tip.     

Interfacial reactions and mechanical properties of ball-grid-array solder joints using Cu-cored solder balls

Interfacial reactions and mechanical properties of the ball-grid-array (BGA) solder joints using monolithic eutectic SnPB and Cu-cored solder balls after reflow and solid-state annealing were investigated. The Cu cores of three different sizes were used in the solder joints. The incorporation of a Cu core into the BGA solder joint effectively inhibits the (Au_1−xNi_x)Sn₄ regrouping and the (Cu_1−x−yAu_xNi_y)₆Sn₅ phase is formed at the joint interface instead. Growth of the intermetallic compounds formed in the monolithic and Cu-cored solder joints approximately obeys the parabolic law. In the Cu-cored solder joints, the larger the Cu core is, the slower the intermetallic compounds grow. The size effect of the Cu core on the intermetallic compound growth results from the inconsistent amount of the outer solder layer. Shear and tensile strengths of the Cu-cored solder joints decrease with increasing solid-state annealing time, and do not have a noticeable relationship with the Cu-core size. Shear and tensile tests also show that the mechanical strength of the Cu-cored solder joint is better than that of the monolithic solder joint.     

热循环条件下Sn基钎料接头电迁移行为研究

通过电迁移和热疲劳循环实验,研究了热循环和高电流密度耦合作用下Sn58Bi和Sn3.0Ag0.5Cu钎料焊接接头的失效形式。实验结果表明,在通电和高低温冲击的耦合作用下,两种钎料接头的失效都发生在升温阶段。热循环导致接头内部裂纹的萌生和扩展,导致局部电流密度持续增大,加速了电迁移的发生,最终导致焊点失效。在热电耦合作用下,Sn58Bi钎料接头的使用寿命要长于Sn3.0Ag0.5Cu钎料接头的使用寿命。     

Temperature profile effects in accelerated thermal cycling of SnPb and Pb-free solder joints

Accelerated thermal cycling (ATC) has been widely used in the microelectronics industry for reliability assessment. ATC testing decreases life cycle test time by one or more of the following means: increasing the heating and cooling rate, decreasing the hold time, or increasing the range of the applied temperature. The relative effect of each of these cycle parameters and the failure mechanisms they induce has been the subject of many studies; however uncertainty remains, particularly regarding the role of the heating and cooling rate. In this research, three conditions with two ramp rates (14 °C/min and 95 °C/min) and two temperature ranges (ΔT = 0–100 °C and −40 to 125 °C) were applied to resistor 2512 and PBGA 256 test vehicles assembled with SnPb and Pb-free solders. The test results showed that the higher ramp rate reduced the testing time while retaining the same failure modes, and that the damage per cycle increased with the temperature difference. For the resistors, the Pb-free solder joints lasted longer than the SnPb joints at the smaller ΔT, but were inferior at the larger ΔT. In contrast, the Pb-free solder joints in the PBGA test vehicles lasted longer than the SnPb solder under both conditions.     

电迁移对Sn3.0Ag0.5Cu无铅焊点剪切强度的影响

通过热风回流焊制备了Cu/Sn3.0Ag0.5Cu/Cu对接互连焊点,测试了未通电及6.5 A直流电下通电36 h和48 h后焊点的剪切强度.结果表明,电迁移显著地降低了焊点的剪切强度,电迁移36 h使剪切抗力降低约30%,电迁移48 h降低约50%.SEM观察断口和界面形貌表明,界面金属间化合物增厚使断裂由韧性向脆性...     

Finite element modeling on electromigration of solder joints in wafer level packages

This work studies the electromigration of solder joints in an encapsulated copper post wafer level package (WLP) by finite element modeling. Experimental data showed that the electromigration failure occurs in solder joints on the printed circuit board (PCB) side due to the current crowding. In order to improve the electromigration performance on the PCB side with a copper post WLP, two new line-to-bump geometry designs are proposed. Coupled electro-thermal finite element modeling is performed to obtain the electrical and thermal fields simultaneously. The ionic flux from electron wind and thermal response is calculated based on finite element solutions. The divergence of the total flux, which is the sum of the divergence of electromigration and thermomigration, is extracted at the critical locations in solder joints. Results show that the new proposed design structures can reduce the maximum current density by 19%, and the divergence of the total ionic flux by 42%. Thermal gradient is very small in solder joints, therefore, the main driving force for electromigration failures comes from the electron wind. The finite element results on mesh dependency are discussed in this paper.     

电迁移作用下的微焊点振动疲劳行为研究

研究了不同电迁移时间(0～96 h)和电流密度(0～1.52×104A/cm2)对Sn-3.0Ag-0.5Cu微焊点振动疲劳行为的影响.结果显示,在电迁移时间和电流密度均为0时,微焊点的振动疲劳循环次数大于1 170次,疲劳寿命大干234 min;而在125℃服役温度下,当振动频率为0.8 Hz,交变应力为0～20 M...     

Interfacial thermal stresses in solder joints of leadless chip resistors

A novel two-dimensional analytical model has been developed for the interfacial thermal stresses in the solder joints of a leadless chip resistor (LCR) assembly under both plane stress and plane strain conditions. Both global and local expansivity mismatches are incorporated into the model. Interfacial thermal stresses are approximated using elementary strength of materials theory. Governing differential equations are linearized through a finite difference discretization procedure. The conditions of zero shear stress at the free edges and self-equilibrated peel stresses are met. The model is more accurate than existing ones, is mathematically straightforward, and can be extended to include inelastic behavior. The results are compared with available data in the literature and finite element analysis, and a geometry optimization is performed for a sample LCR as an example of the use of the model.