三轮驱动移动机器人轨迹跟踪控制

针对三轮驱动移动机器人在轨迹跟踪控制过程中运动不平滑的问题,建立了移动机器人在一定运动约束条件下的运动学模型。根据移动机器人位姿误差微分方程的描述,设计了基于后退时变状态反馈方法的移动机器人轨迹跟踪控制器。基于李雅普诺夫方法,对轨迹跟踪控制器的稳定性进行了分析,证明了该控制器能够保证闭环系统全局一致渐进稳定。仿真结果验证了运动学模型的正确性,以及轨迹跟踪控制器的有效性。     

Omni-directional mobile robot controller based on trajectory linearization

In this paper, a nonlinear controller design for an omni-directional mobile robot is presented. The robot controller consists of an outer-loop (kinematics) controller and an inner-loop (dynamics) controller, which are both designed using the Trajectory Linearization Control (TLC) method based on a nonlinear robot dynamic model. The TLC controller design combines a nonlinear dynamic inversion and a linear time-varying regulator in a novel way, thereby achieving robust stability and performance along the trajectory without interpolating controller gains. A sensor fusion method, which combines the onboard sensor and the vision system data, is employed to provide accurate and reliable robot position and orientation measurements, thereby reducing the wheel slippage induced tracking error. A time-varying command filter is employed to reshape an abrupt command trajectory for control saturation avoidance. The real-time hardware-in-the-loop (HIL) test results show that with a set of fixed controller design parameters, the TLC robot controller is able to follow a large class of 3-degrees-of-freedom (3DOF) trajectory commands accurately.     

轮式机器人滑模轨迹跟踪控制器设计

轮式机器人是一个典型的非完整性系统。由于非线性和非完整特性,很难为移动机器人系统的轨迹跟踪建立一个合适的模型。介绍了一种轮式机器人滑模轨迹跟踪控制方法。滑模控制是一个鲁棒的控制方法,能渐近的按一条所期望的轨迹稳定移动机器人。以之为基础,描述了轮式机器人的动力学模型并在二维坐标下建立了运动学方程,根据运动学方程设计滑模控制器,该控制器使得机器人的位置误差收敛到零。     

带有未知参数和有界干扰的移动机器人轨迹跟踪控

针对模型参数未知和存在有界干扰的非完整移动机器人的轨迹跟踪控制问题,本文提出了一种鲁棒自适应轨迹跟踪控制器方法.非完整移动机器人的控制难点在于它的运动学系统是欠驱动的.针对这一难点,本文利用横截函数的思想,引入新的辅助控制器,使得非完整移动机器人系统不再是一个欠驱动系统,缩减了控制器设计的难度,进而利用非线性自适应算法和参数映射方法构造李雅谱诺夫函数.通过李雅普诺夫方法设计控制器和参数自适应器,从而使得非完整移动机器人的跟随误差任意小,即可以任意小的误差来跟随任意给定的参考轨迹.仿真结果证明了方法的有效性.     

基于神经网络的不确定移动机器人鲁棒自适应跟踪控制

针对含运动学未知参数以及动力学模型不确定的非完整轮式移动机器人轨迹跟踪问题,基于Radical Basis Function(径向基函数)神经网络,提出了一种鲁棒自适应控制器.首先,考虑移动机器人运动学参数未知的情况,提出了一种含自适应参数的运动学控制器,用以补偿参数不确定性导致的系统误差;其次,利用神经网络控制技术,对于机器人在移动中动力学模型不确定问题,提出了一种具有鲁棒性的动力学控制器,使得移动机器人可以在不知道具体动力学模型的情况下跟踪到目标轨迹;最后利用Lyapunov稳定性理论证明了整个系统的稳定性.通过数值仿真验证了所设计的控制器的可行性.     

基于视觉图像的全向移动机器人轨迹跟踪控制研究

机器人轨迹节点跟踪比较难,导致机器人实际轨迹偏离期望轨迹,所以设计基于视觉图像的全向移动机器人轨迹跟踪控制方法;构建全向移动机器人的运动学数学模型,以此确定机器人移动轨迹数学模型;以移动轨迹数学模型为基础,按照视觉图像划分标准对全向移动机器人运动图像的分割,通过分离目标节点的方式提取运动学特征参量,完成机器人轨迹节点跟踪处理;结合节点跟踪处理结果,将运动学不等式与误差向量作为机器人轨迹跟踪控制的约束条件,利用滑模变结构搭建轨迹跟踪控制模型,实现全向移动机器人轨迹跟踪控制;对比实验结果表明,所设计的方法应用后,全向移动机器人角速度曲线、线速度曲线与期望运动轨迹曲线之间的贴合程度均超过90%,满足全向移动机器人轨迹跟踪控制要求。     

滑动与打滑条件下的轮式移动机器人自抗扰跟踪控制

针对具有未知的滑动与打滑的轮式移动机器人(WMR),提出了一种基于自抗扰思想的跟踪控制策略.首先建立了滑动与打滑条件下的轮式移动机器人动力学模型.其次,由反步法设计运动学控制器,基于模型设计线性扩张观测器和动力学控制器,并给出了控制器稳定性分析.最后与积分滑模控制进行了仿真对比,结果表明该控制方法的误差收敛速度更快.观测器能够精确估计滑动与打滑及动力学不确定性对机器人的扰动,提高了轮式移动机器人轨迹跟踪的鲁棒性.     

信息融合在移动机器人轨迹模糊跟踪中的应用

在机器人轨迹跟踪过程中,机器人自动跟踪的精度直接影响跟踪效果;以3自由度移动机器人为研究对象研究了机器人轨迹模糊跟踪系统,且在该系统中,采用多个传感器同时对移动机器人进行跟踪检测,并利用融合算法对其进行融合,将融合后的结果作为模糊控制器的输入;计算机仿真结果表明,在3自由度移动机器人轨迹跟踪中,采用多传感器信息融合是合理的、可行的;且可以减少跟踪过程中由传感器引起的误差对跟踪精度的影响,提高控制精度.     

Output feedback control of a skid-steered mobile robot based on the super-twisting algorithm

This paper presents the design and implementation of an output feedback controller based on the super twisting algorithm (STA) that stabilizes the trajectory tracking error of a skid steered mobile robot (SSMR). The control scheme introduces a diffeomorphism based on the mathematical model of the SSMR to transform the original problem into a third order chain of integrators. In this study, the available measurements are the position and orientation of the SSMR. A modified STA working as a step by step differentiator estimates the velocity and acceleration of the mobile robot. Then, a second STA enforces the tracking of a predefined trajectory. Numerical and experimental results comparing the STA with a state feedback controller (SFC) and a first order sliding mode controller (FOSM) justify the control proposal.     

A new adaptive tracking control scheme of wheeled mobile robot without longitudinal velocity measurement

This paper proposes a new adaptive trajectory tracking control scheme of the wheeled mobile robot without longitudinal velocity measurement. First, based on a kinematic controller, we obtain a new tracking error equation, which is suitable to develop an adaptive controller. Then, we develop a new adaptive trajectory tracking controller, which does not need any accurate values of the wheeled mobile robot parameters, including the driving motor parameters. Moreover, as the longitudinal velocity measurement is still difficult, this controller is developed without longitudinal velocity measurement. In addition, this new adaptive controller introduces a method to improve the control performance. The stability of the closed‐loop system is presented using the direct Lyapunov method. Finally, numerous simulations verify the effectiveness of the new controller.     

基于全局视觉的轮式移动机器人轨迹跟踪控制

将视觉伺服控制思想引入到全局视觉条件下的轮式移动机器人轨迹跟踪控制中,提出一种基于消除图像特征误差的控制方法.讨论并推导了包含电机模型的非完整移动机器人动力学方程,设计了鲁棒速度跟踪控制器.实验结果证明了文中方法的有效性.􀁱     

考虑运动受限的履带式移动机器人轨迹跟踪控制

针对履带式移动机器人的轨迹跟踪控制问题进行研究,首先,建立了履带式移动机器人的运动学模型和跟踪误差模型;其次,设计了转速有限时间控制和线速度滑模控制的轨迹跟踪控制律,并给出了考虑运动受限作用下的控制律修正表达式;最后,基于MATLAB对所提控制律进行仿真,对比分析了不考虑运动受限情况下跟踪控制效果;结果表明,设计的跟踪控制律能够实现履带式移动机器人对圆轨迹的有效跟踪,且考虑运动受限作用的控制律更加符合实际;文章研究分析了运动受限作用对于移动机器人轨迹跟踪控制的影响,分析结果对其他移动机器人的运动控制研究具有参考价值。     

基于变增益模糊PID控制的移动机器人轨迹跟踪

该文对轮式移动机器人提出了一种基于变增益的模糊PID轨迹跟踪控制方法。首先将常规PID分为PI和PD的组合,再把PID的输出转化为误差和误差变化率之和,然后设计增益随误差变化的自适应调节律,使得移动机器人跟踪期望的运动轨迹。最后通过实验验证了所提方法的有效性。     

Smooth control of an articulated mobile robot with switching constraints

The paper describes a smooth controller of an articulated mobile robot with switching constraints. The use of switching constraints associated with grounded/lifted wheels is an effective method of controlling various motions; e.g. the avoidance of a moving obstacle. A model of an articulated mobile robot that has active and passive wheels and active joints with switching constraints is derived. A controller that accomplishes the trajectory tracking of the robot’s head and subtasks using smooth joint input is proposed on the basis of the model. Simulations and experiments are presented to show the effectiveness of the proposed controller.     

基于Lyapunov方法和快速终端滑模的轨迹跟踪控制

针对移动机器人的运动学模型,提出一种具有全局渐近稳定性的跟踪控制器。该跟踪控制器的设计分为两部分：第一部分是采用全局快速终端滑动模态的思想设计了角速度的控制律,用来渐近镇定移动机器人跟踪的前向角误差;第二部分是采用Lyapunov方法设计了线速度的控制律,用来渐近镇定移动机器人跟踪的平面坐标误差。采用Lyapunov稳定性定理,证明了移动机器人在满足这些控制律条件下,实现了对参考轨迹的全局渐近跟踪。实验结果表明移动机器人能够有效地跟踪期望轨迹,有利于在实际应用中推广。     

基于眼到手视觉伺服的移动机器人模型预测控制

针对具有速度约束的移动机器人视觉轨迹跟踪问题,提出了一种基于LOQO内点法的模型预测控制方法;在眼到手框架下,首先建立了移动机器人误差模型,并对该误差模型进行离散化,给出了移动机器人视觉伺服跟踪的代价函数;同时考虑到实际中移动机器人存在速度约束问题,将代价函数的最小化问题转换为带输入约束的模型预测控制问题;然后采用障碍函数法将移动机器人的速度约束转化为等式约束并采用拉格朗日乘子法引入到代价函数中;进而,利用LOQO内点法求解具有速度约束的最小化问题,得到基于视觉的轨迹跟踪控制器;最后,通过仿真验证了所提算法的有效性和优越性.     

基于预测控制的非连续路段下移动机器人的轨迹跟踪

针对非连续路段下的轨迹跟踪问题,设计了基于观测型的预测控制器。首先建立了移动机器人的运动学模型,根据机器人的运动学模型得出了其位姿误差微分方程;然后在轨迹跟踪问题的基础上,设计了系统的观测模型,通过将预测控制器与系统的观测模型结合,设计了观测型预测控制器;最后再MATLAB环境下,利用本文所设计的控制器对移动机器人在非连续路段下的轨迹跟踪问题进行仿真,并将仿真结果与PID控制器控制的仿真结果进行对比,由仿真结果可以看出,本文所设计的控制器具有很好的鲁棒性、快速性及稳定性,可适用于移动机器人的轨迹跟踪的研究。     

Adaptive sliding mode control for trajectory tracking of nonholonomic mobile robot with uncertain kinematics and dynamics

ABSTRACT

This article designs a novel adaptive trajectory tracking controller for nonholonomic wheeled mobile robot under kinematic and dynamic uncertainties. A new velocity controller, in which kinematic parameter is estimated, produces velocity command of the robot. The designed adaptive sliding mode dynamic controller incorporates an estimator term to compensate for the external disturbances and dynamic uncertainties and a feedback term to improve the closed-loop stability and account for the estimation error of external disturbances. The system stability is analyzed using Lyapunov theory. Computer simulations affirm the robustness of the designed control scheme.     

Trajectory tracking optimization of mobile robot using artificial immune system

In this paper, an optimization method that provides quick response using artificial immune system, is proposed and applied to a mobile robot for trajectory tracking. The study focuses on the immune theory to derive a quick optimization method that puts emphasis on immunity feedback using memory cells by the expansion and suppression of the test group rather than to derive a specific mathematical model of the artificial immune system. Various trajectories were selected in mobile environment to evaluate the performance of the proposed artificial immune system. The global inputs to the mobile robot are reference position and reference velocity, which are time variables. The global output of mobile robot is a current position. The tracking controller makes position error to be converged to zero. In order to reduce position error, compensation velocities on the track of trajectory are necessary. Input variables of fuzzy are position errors in every sampling time. The output values of fuzzy are compensation velocities. Immune algorithm is implemented to adjust the scaling factor of fuzzy automatically. The results of the computer simulation proved the system to be efficient and effective for tracing the trajectory to the final destination by the mobile robot.

     

Design of a sliding mode controller for an automatic guided vehicle and its implementation

In this paper, a control scheme that combines a kinematic controller and a sliding mode dynamic controller with external disturbances is proposed for an automatic guided vehicle to track a desired trajectory with a specified constant velocity. It provides a method of taking into account specific mobile robot dynamics to convert desired velocity control inputs into torques for the actual mobile robot. First, velocity control inputs are designed for the kinematic controller to make the tracking error vector asymptotically stable. Then, a sliding mode dynamic controller is designed such that the mobile robot’s velocities converge to the velocity control inputs. The control law is obtained based on the backstepping technique. System stability is proved using the Lyapunov stability theory. In addition, a scheme for measuring the errors using a USB camera is described. The simulation and experimental results are presented to illustrate the effectiveness of the proposed controller.