Analysis of Time-Dependent Tritium Breeding Capability of Water Cooled Ceramic Breeder Blanket for CFETR

Attaining tritium self-sufficiency is an important mission for the Chinese Fusion Engineering Testing Reactor(CFETR) operating on a Deuterium-Tritium(D-T) fuel cycle. It is necessary to study the tritium breeding ratio(TBR) and breeding tritium inventory variation with operation time so as to provide an accurate data for dynamic modeling and analysis of the tritium fuel cycle. A water cooled ceramic breeder(WCCB) blanket is one candidate of blanket concepts for the CFETR. Based on the detailed 3D neutronics model of CFETR with the WCCB blanket,the time-dependent TBR and tritium surplus were evaluated by a coupling calculation of the Monte Carlo N-Particle Transport Code(MCNP) and the fusion activation code FISPACT-2007.The results indicated that the TBR and tritium surplus of the WCCB blanket were a function of operation time and fusion power due to the Li consumption in breeder and material activation.In addition, by comparison with the results calculated by using the 3D neutronics model and employing the transfer factor constant from 1D to 3D, it is noted that 1D analysis leads to an over-estimation for the time-dependent tritium breeding capability when fusion power is larger than 1000 MW.     

Neutronics Comparison Analysis of the Water Cooled Ceramics Breeding Blanket for CFETR

China Fusion Engineering Test Reactor(CFETR) is an ITER-like fusion engineering test reactor that is intended to fill the scientific and technical gaps between ITER and DEMO.One of the main missions of CFETR is to achieve a tritium breeding ratio that is no less than 1.2to ensure tritium self-sufficiency.A concept design for a water cooled ceramics breeding blanket(WCCB) is presented based on a scheme with the breeder and the multiplier located in separate panels for CFETR.Based on this concept,a one-dimensional(1D) radial built breeding blanket was first designed,and then several three-dimensional models were developed with various neutron source definitions and breeding blanket module arrangements based on the 1D radial build.A set of nuclear analyses have been carried out to compare the differences in neutronics characteristics given by different calculation models,addressing neutron wall loading(NWL),tritium breeding ratio(TBR),fast neutron flux on inboard side and nuclear heating deposition on main in-vessel components.The impact of differences in modeling on the nuclear performance has been analyzed and summarized regarding the WCCB concept design.     

CFETR氦冷固态增殖剂包层产氚性能研究及优化

氦冷固态增殖剂包层是中国聚变工程实验堆（CFETR）的3种候选包层概念之一。本文基于中国核工业西南物理研究院提出的一种氦冷固态增殖剂包层概念,通过蒙特卡罗输运程序MCNP5建立了包层三维中子学模型,探究了不同几何布置方案及结构设计参数对包层产氚性能的影响,得到了全堆氚增殖比（TBR）及极向各包层模块产氚分布,并由优化后的模型得到了包层模块核热分布。结果表明,优化后的TBR达到1.177,满足氚自持的最低要求。     

中国聚变工程试验堆包层的核热耦合效应研究

本文以中国聚变工程试验堆（CFETR）的氦冷固态包层和水冷固态包层为研究对象,基于蒙特卡罗程序MCNP和计算流体力学程序FLUENT,利用3D-1D-2D耦合方法和伪材料方法,分别对200 MW的氦冷固态包层和水冷固态包层及1.5 GW的水冷固态包层方案进行了核热耦合计算分析。研究结果表明,金属铍的热散射效应和轻水密度是聚变包层核热耦合效应的主要来源,核热耦合效应对氦冷固态包层的影响可忽略,对水冷固态包层的氚增殖比和温度分布有一定程度的影响。     

托卡马克聚变中子源的数值模型研究

托卡马克(Tokamak)聚变装置中子学分析中,聚变中子源描述是重要的输入参数,其准确性直接影响分析结果的可靠性。通过分析ITER和欧洲聚变示范堆(EU DEMO)中子学分析中所采用的聚变中子源模型,提出了一种完整描述Tokamak中L-mode、H-mode等离子体的D-D、D-T聚变中子源的数值模型。在中国聚变工程实验堆(CFETR)的工程集成设计平台上,编写了基于蒙特卡罗算法的程序SCG求解该数值模型,实现了读取(零维)等离子体参数、输出可供典型中子学软件MCNP直接读取的中子源定义文件的功能。以CFETR氦冷球床包层的中子学分析模型为基准,在相同的L-mode等离子体D-T聚变工况下,相较于采用EU DEMO源子程序,采用本模型计算得到的中子壁负载差异最大值为2.02%,包层氚增殖率差异为0.18%,全堆能量增益因子的差异为0.23%。结果表明,本模型与其他源描述的差异较小,可应用于CFETR的中子学分析。     

CFETR氦冷陶瓷增殖包层中子学分析

为满足中国聚变工程实验堆(CFETR)包层的应用要求,本文提出氦冷陶瓷增殖(HCCB)包层方案。为验证HCCB包层设计方案的合理性与可行性,采用三维蒙特卡罗粒子输运程序MCNP,计算和分析了HCCB包层方案的氚增殖比、中子壁负载、中子通量密度、核热、辐照损伤等中子学特性。结果表明,HCCB包层方案满足氚自持要求,中子通量密度和核热分布合理,屏蔽性能良好,基本满足设计要求。     

Neutronics Analysis of Water-Cooled Ceramic Breeder Blanket for CFETR

In order to investigate the nuclear response to the water-cooled ceramic breeder blanket models for CFETR, a detailed 3D neutronics model with 22.5otorus sector was developed based on the integrated geometry of CFETR, including heterogeneous WCCB blanket models,shield, divertor, vacuum vessel, toroidal and poloidal magnets, and ports. Using the Monte Carlo N-Particle Transport Code MCNP5 and IAEA Fusion Evaluated Nuclear Data Library FENDL2.1,the neutronics analyses were performed. The neutron wall loading, tritium breeding ratio, the nuclear heating, neutron-induced atomic displacement damage, and gas production were determined.The results indicate that the global TBR of no less than 1.2 will be a big challenge for the watercooled ceramic breeder blanket for CFETR.     

Conceptual design of a water cooled breeder blanket for CFETR

China Fusion Engineering Test Reactor (CFETR) is an ITER-like superconducting tokamak reactor. Its major radius is 5.7 m, minor radius is 1.6 m and elongation ratio is 1.8. Its mission is to achieve 50–200 MW of fusion power, 30–50% of duty time factor, and tritium breeding ratio not less than 1.2 to ensure the self-sufficiency. As one of the breeding blanket candidates for CFETR, a water cooled breeder blanket with superheated steam is proposed and its conceptual design is being carried out. In this design, sub-cooling water at 265 °C under the pressure of 7 MPa is fed into cooling plates in breeding zone and is heated up to 285 °C with saturated steam generated, and then this steam is pre-superheated up to 310 °C in first wall (FW), final, the pre-superheated steam coming from several blankets is fed into the other one blanket to superheat again up to 517 °C. Due to low density of superheated steam, it has negligible impact on neutron absorption by coolant in FW so that the high energy neutrons entering into breeder zone moderated by water in cooling plate help enhance tritium breeding by ⁶Li(n,α)T reaction. Li₂TiO₃ pebbles and Be₁₂Ti pebbles are chosen as tritium breeder and neutron multiplier respectively, because Li₂TiO₃ and Be₁₂Ti are expected to have better chemical stability and compatibility with water in high temperature. However, Be₁₂Ti may lead to a reduction in tritium breeding ratio (TBR). Furthermore, a spot of sintered Be plate is used to improve neutron multiplying capacity in a multi-layer structure. As one alternative option, in spite of lower TBR, Pb is taken into account to replace Be plate in viewpoint of safety. In this contribution, study on neutronics and thermal design for a water cooled breeder blanket with superheated steam is reported.     

聚变堆交叉冷却固态包层中子学设计优化

针对聚变堆固态包层设计路线,提出了一个交叉排列氦冷固态包层概念。设计采用Be、Li₂TiO₃分层球床。两种尺寸的氦气冷却管道交叉排列,分两个回路同时冷却,以增加系统安全可靠性。分析比较了4种⁶Li富集度布置方案。结果表明：径向远离第一壁降低⁶Li富集度较为合理,靠近第一壁的增殖层⁶Li富集度不能过低,以减少长期运行中Li的消耗对氚增殖性能的影响。借助蒙特卡罗程序MCNP建立11.25°对称模型,全堆包层氚增殖率为1.176,包层寿期内产氚性能稳定,在包层寿命运行时间内的燃耗分布相对均匀。     

超临界水冷固态实验包层中子学与热工水力特性研究

基于国际热核聚变实验堆(ITER)实验包层方案,提出了一个超临界水冷固态实验包层概念设计方案。设计采用Be作为中子倍增剂,Li4SiO4作为氚增殖剂,CLAM钢作为结构材料。包层第一壁采用多层盘道设计以提高第一壁出口温度,内部采用增殖剂与中子倍增剂分层布置以提高热沉积与氚增殖率。为验证包层设计的可行性,分析计算了三维包层氚增殖率与热沉积的分布,然后根据中子学计算得到的结果对超临界水冷固态实验包层进行了数值模拟研究。结果表明:包层功率密度分布较合理;氚增殖率满足运行中氚自持的要求;在冷却剂出口温度达到500℃条件下材料温度不超过限值。该设计方案能满足中子学设计与热工水力的要求。     

CFETR氚自持分析评估与验证策略

中国聚变工程实验堆(China Fusion Engineering Test Reactor,简称CFETR)的主要目标之一是实现氚自持.采用氚平衡法对CFETR不同运行工况下的氚自持条件进行了分析评估.结果表明:在500 MW运行阶段,CFETR实现氚自持所需的最小氚增殖比(TBRr)为1.098,小于CFETR增...     

Updated neutronics analyses of a water cooled ceramic breeder blanket for the CFETR

The water cooled ceramic breeder (WCCB) blanket employing pressurized water as a coolant is one of the breeding blanket candidates for the China Fusion Engineering Test Reactor (CFETR).Some updating of neutronics analyses was needed,because there were changes in the neutronics performance of the blanket as several significant modifications and improvements have been adopted for the WCCB blanket,including the optimization of radial build-up and customized structure for each blanket module.A 22.5 degree toroidal symmetrical torus sector 3D neutronics model containing the updated design of the WCCB blanket modules was developed for the neutronics analyses.The tritium breeding capability,nuclear heating power,radiation damage,and decay heat were calculated by the MCNP and FISPACT code.The results show that the packing factor and 6Li enrichment of the breeder should both be no less than 0.8 to ensure tritium self-sufficiency.The nuclear heating power of the blanket under 200 MW fusion power reaches 201.23 MW.The displacement per atom per full power year (FPY) of the plasma-facing component and first wall reach 0.90 and 2.60,respectively.The peak H production rate reaches 150.79 appm/FPY and the peak He production reaches 29.09 appm/FPY in blanket module # 3.The total decay heat of the blanket modules is 2.64 MW at 1 s after shutdown and the average decay heat density can reach 11.09 kW m-3 at that time.The decay heat density of the blanket modules slowly decreases to lower than 10 W m-3 in more than ten years.     

CFETR氦冷固态包层及其辅助系统动态氚输运分析

实现氚自持、建立完整的氚循环系统并保证氚安全是中国聚变工程实验堆(CFETR)的主要目标之一.在CFETR氦冷固态包层及其辅助系统设计过程中,需对系统级氚输运行为进行详细分析,包括氚滞留量、释放量、浓度的动态变化等.基于已建立的动态氚分析程序T riSim-Dynamic,在此基础上进行修改完善,利用该程序对CFETR...     

cosRMC复杂曲面开发及在聚变中子学的应用

中国聚变工程实验堆（CFETR）是我国自主设计和研制的重大科学工程,CFETR旨在与ITER相衔接和补充,为研制DEMO级别聚变堆电站提供必要的技术。蒙特卡罗方法在聚变中子学与屏蔽设计等方面具有重要作用。本文基于自主化蒙特卡罗程序cosRMC,研究了蒙特卡罗复杂曲面建模的数学模型和计算方法,开发了复杂曲面建模功能,并通过PPCS（power plant conceptual study）模型验证了该功能实现的正确性。然后构建了CFETR的三维精细化模型,并利用该模型对CFETR包层设计中的关键中子学参数进行计算分析。结果表明,cosRMC对中子学参数氚增殖比、中子壁载荷和核热沉积的计算结果与MCNP的计算值吻合良好,相对偏差均小于5%,满足工程设计需求。研究证明了cosRMC应用于聚变堆包层中子学分析的正确性和有效性。CFETR中子学参数的计算分析,也为其设计和优化提供了参考。     

聚变堆混和球床包层中子学和热工水力特性研究

在聚变堆初步概念设计的基础上，针对固态包层设计路线，提出了一个先进的氦冷固态包层概念。设计采用Be₁₂Ti和Li₂TiO₃陶瓷小球混和球床，物理和化学相容性好；采用SiC作为结构材料，提高耐高温性能及氦气出口温度。计算结果表明：选择Be₁₂Ti和Li^₂TiO₃球体积比在2和4之间较合理；在Be₁₂Ti和Li₂TiO₃球体积比为3时，⁶Li富集度取30％~80％较适宜；球床的最高温度低于材料的温度限值，温度分布合理均匀。该方案可较大程度提高热效率和改善中子学以及氚增殖性能。     

氦气、水和熔盐冷却的混合堆中子学性能研究

氦气、水、熔盐(Flibe)在强磁场中流动不存在严重的MHD问题,因此适合在基于磁约束的聚变-裂变混合堆中作为冷却剂.针对氦气、水、Flibe这3种冷却剂对混合堆包层中子学性能的影响进行研究,分析包层中能谱特点及燃料增殖特性.通过燃耗计算,研究氚增殖率(TBR)、能量倍增因子(M)、keff等随运行时间的变化.中子学输运采用三维蒙特卡罗程序MCNP.计算结果表明,不同的冷却剂对混合堆系统中子能谱影响很大:氦冷系统的能谱最硬,主要发生快中子裂变,氚增殖效果最好;水冷系统的能谱最软,产能最多,但需提高TBR;Flibe冷系统的能谱较硬,产能最少.     

聚变驱动的次临界系统嬗变MA的研究

一种嬗变次锕系核素(MA)的聚变驱动次临界包层的概念设计被提出。利用MCNP+ORIGEN2对次临界嬗变包层的能量放大倍数(M)、氚增殖比(TBR)、第一壁负载等中子学参数进行了分析。在保证这些参数满足设计要求的前提下,分析了两种不同的装载方案对MA嬗变能力的影响,最终MA的嬗变率能达24.3%,嬗变支持比为28。研究表明,该聚变驱动次临界嬗变包层能有效嬗变MA。     

Effect of Nuclear Data Libraries on Tritium Breeding in a (D–T) Fusion Driven Reactor

In design a Deuterium–Tritium (D–T) fusion driven hybrid reactor, neutronics and nuclear data libraries have an essential role for reliable neutronics calculations. Therefore, nuclear data libraries are very important to calculate of the neutronic parameters and selection of tritium breeder materials to be used in the blanket. In this study tritium breeding performances of candidate tritium breeding materials, namely, Li₂O, LiH, Li₂TiO₃, Li₂ZrO₃ and Li₄SiO₄ in a (D–T) driven fusion–fission (hybrid) reactor is investigated based on three dimensional (3-D) and one dimensional (1-D) neutronic calculations. 3-D and 1-D neutron transport calculations are performed with Monte Carlo transport code (MCNP 4C), SCALE 5 and ANISN nuclear data codes to determine the tritium breeding ratio (TBR) of the blanket. The effects of different nuclear data libraries on TBR are examined and TBR calculation results are comparatively investigated.