Influence of the molecular structure of poly(vinyl alcohol) on the ultrasonic absorption

The properties of poly(vinyl alcohol) are essentially determined by the content of residual acetate groups. In this paper the influence of the molecular structure on the ultrasonic absorption is studied. As structure parameters, the residual acetate content and the ¹³C n.m.r. microstructure parameters are determined. Some commercial and laboratory products prepared by different methods are investigated. Broad ultrasonic absorption spectra are obtained. The theory of normal mode relaxation of the Rouse-Zimm type can be applied. For products with higher acetate contents, notable discrepancies between normal mode losses and measured absorption occur. The influence of acetate content and block structure on ultrasonic absorption is demonstrated but the absorption behaviour cannot only be explained by both parameters in all cases.     

Dielectric dispersion studies of poly(vinyl alcohol) in aqueous solutions

The dielectric constant ε′ and loss factor ε″ of deionized water and poly(vinyl alcohol) in aqueous solutions are measured in the frequency region 200 MHz to 20 GHz at four different temperatures (25, 35, 45 and 55 °C). Complex plane plots (ie ε″ vs ε′) are drawn to obtain the static dielectric constant ε₀, high frequency dielectric constant ε_∞, distribution parameter α and average relaxation time τ₀. The variations of dielectric constants with increasing solvent concentration and temperature are discussed in terms of solute–solvent and solute–solute interactions. The average relaxation time τ₀ of poly(vinyl alcohol) aqueous solutions is found to the very short. It is also observed that the relaxation time is almost independent of the viscosity of the solution. The effect of water concentration on macromolecular size, shape and flexibility of the molecular chain are discussed using the observed values of dielectric relaxation times at different temperatures. The possibility of multiple dielectric dispersion is also discussed with concentration variation. © 2000 Society of Chemical Industry     

Thermal characteristics of poly(vinyl alcohol) and poly(vinylpyrrolidone) IPNs

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and 1‐vinyl‐2‐pyrrolidone (VP) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone (DMPAP) and methylene bisacrylicamide (MBAAm) as initiator and crosslinker, respectively. The thermal characterization of the IPNs was investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depressions of the melting temperatures of PVA segments in IPNs were observed with increasing VP content via the DSC. The DEA was employed to ascertain the glass transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_gs indicating the presence of phase separation in the IPN. The thermal decomposition of IPNs was investigated using TGA and appeared at near 270°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1844–1847, 2002     

Interpolymer associations between poly(vinyl alcohol) and poly(diallyldimethylammonium chloride) in aqueous dilute solution

This article studied the compatibility of poly(vinyl alcohol) (PVA) with poly(diallyldimethylammonium chloride) (PDADMACl) in a dilute aqueous solution. At a total mixture concentration and a constant molecular weight of PDADMACl, it was found that interpolymer associations increase with the molecular weight and decrease with the degree of hydrolysis of the PVA sample (87–89 and 98–99%). From these results, it can be deduced that the compatibility of PVA and PDADMACl is due to specific intermolecular interactions that could be assigned mainly to electrostatic interactions between hydroxyl groups within PVA chains and ion atoms within PDADMACl. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 433–435, 2002     

The influence of poly(vinyl alcohol) suspending agents on suspension poly(vinyl chloride) morphology

The requirements for PVC suspension resin have changed considerably in the last few years, so much so that few companies have products on their ranges that are more than 4 or 5 years old. The suspending agent has a crucial influence on the morphology of the resin, so the changes in resin characteristics have largely been achieved by changes in the suspending agent systems. After a brief review of the mechanism of PVC suspension polymerisation, the properties of polymers made using PVOH suspending agents are related to changes in the latter. The effect of variations in PVAc degree of hydrolysis and viscosity are related to changes in surface tension. Methods of achieving higher porosity by using low hydrolysis co-suspending agents are described. It is shown that higher bulk densities can be achieved by delayed addition of the PVOH. Levels of conjugated unsaturation and copolymer distributions are also shown to have important influences.     

Effects of the tacticities of poly(vinyl alcohol) on the structure and morphology of poly(vinyl alcohol) nanowebs prepared by electrospinning

The effects of tacticities on the characteristics of poly(vinyl alcohol) (PVA) nanowebs prepared by an electrospinning technique were investigated. PVA webs composed of uniform nanofibers with syndiotactic dyad (s‐dyad) contents of 53.5 and 57.3% were successfully obtained with electrospinning. By changing processing parameters such as the initial polymer concentration, applied voltage, and tip‐to‐collector distance, we found suitable conditions for forming PVA webs with uniform nanofibers. PVAs of higher s‐dyad contents were prepared at a lower solution concentration and at a higher applied voltage because of the easy formation of syndiotactic PVA chain entanglements at a very low polymer concentration. The average diameter of the nanofibers in a PVA web with the higher s‐dyad content of 57.3% (ca. 240 nm) was thinner than that of the nanofibers in a PVA web with the lowers‐dyad content of 53.5% (ca. 270 nm). In addition, the crystallinity and thermal stability were greatly increased with an increase in the s‐dyad content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Investigation of the interpolymer association between poly(vinyl alcohol) and poly(sodium styrene sulfonate) in aqueous solution

A viscosimetric method has been used to study the interpolymer association between poly(vinyl alcohol) (PVA) and poly(sodium styrene sulfonate) (PSSNa) in aqueous solution. At constant molecular weight of PSSNa, it was found that, the PVA and PSSNa associations were improved with the decrease of molecular weight of PVA and the decrease of its hydrolysis degree. The measurement of intrinsic viscosity [η] and the determination of Huggins associative coefficient K_H of different PVA samples were used to select the most appropriate PVA sample, which leads to homogeneous polymer–polymer mixtures (PVA with hydrolysis degree 87–89%, molecular weight 124,000–186,000 g/mol, intrinsic viscosity [η] = 1.02 dL/g, and Huggins associative coefficient K_h.ass = 0.76). The obtained results show that the interpolymer association between PVA and PSSNa, in aqueous solution, is mainly due to intermolecular hydrogen bonds between hydroxyl groups of PVA and sulfonate groups of PSSNa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of ultra‐low molecular weight poly(vinyl alcohol) graft copolymer

Graft reaction of acrylamide (AM) and 4‐vinyl pyridine (4‐VP) onto ultra‐low molecular weight poly(vinyl alcohol) by ceric (IV) ion initiation had been systematically investigated; and the graft conditions were optimized by studying the effect of monomer/initiator concentration, solvents composition, reaction time and temperature. At optimized conditions, the maximum grafting efficiency and grafting ratio was ～ 50% and 51%, respectively with the presence of AM, whereas they decreased to 19% and 23%, respectively, without the presence of AM. Thermogravimetric analysis showed that as‐resulted graft copolymer had a lower thermal stability than homopolymer PVA. FTIR and ¹H‐NMR confirmed chemical structure of as‐synthesized graft copolymer. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of stereoregularity and molecular weight on the mechanical properties of poly(vinyl alcohol) hydrogel

The effect of the stereoregularity and molecular weight of poly(vinyl alcohol) (PVA) on the mechanical properties of hydrogel was investigated. Compressive strength, creep behavior, and dynamic viscoelasticity were measured on hydrogels of syndiotacticity‐rich PVA derived from poly(vinyl pivalate) (D_p = 1690 diad‐syndiotacticity = 61%, D_p = 8020 diad‐syndiotacticity = 62%) and atactic PVA (D_p = 1750 diad‐syndiotacticity = 54%, D_p = 7780 diad‐syndiotacticity = 54%). Increasing the molecular weight of molecular chains constituting the gel improved the compressive strength of atactic PVA hydrogel. The stereoregularity of PVA had a greater effect than molecular weight on the strength of the hydrogel. Gel prepared from 8.8 g/dL syndiotacticity‐rich PVA had a high compressive modulus of 10 kPa, and the compressive modulus of the gel prepared from 3.3 g/dL was comparable with that of atactic PVA hydrogel prepared with more than 6 g/dL. The dynamic storage modulus of the gel derived from syndiotacticity‐rich PVA was remarkably higher than that of the atactic PVA gel and remained constant up to 60°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of ultrahigh molecular weight syndiotactic poly(vinyl alcohol) microfibrillar fibers by low‐temperature solution polymerization of vinyl pivalate in tertiary butyl alcohol and saponification

Vinyl pivalate (VPi) was solution polymerized in tertiary butyl alcohol (TBA) and in dimethyl sulfoxide (DMSO) with a low chain transfer constant using a low temperature initiator, 2,2′‐azobis(2,4‐ dimethylvaleronitrile) (ADMVN). The effects of polymerization temperature and initiator concentration were investigated in terms of polymerization behavior and molecular structures of poly(vinyl pivalate) (PVPi) and its saponification product poly(vinyl alcohol) (PVA). TBA was absolutely superior to DMSO in increasing the syndiotacticity and molecular weight of PVA. In contrast, TBA was inferior to DMSO in causing conversion to polymer, indicating that the initiation rate of VPi production in TBA was lower than that in DMSO. These effects could be explained by a kinetic order of ADMVN concentration, calculated by the initial rate method. Low‐temperature solution polymerization of VPi in TBA or DMSO by adopting ADMVN proved to be successful in obtaining PVA of ultrahigh molecular weight [maximum number‐average degree of polymerization (P_n): 13,500–17,000] and of high yield (ultimate conversion of VPi into PVPi: 55–83%). In the case of bulk polymerization of VPi at the same conditions, maximum P_n and conversion were 14,500–17,500 and 22–36%, respectively. The P_n and syndiotactic diad content were much higher and the degree of branching was lower with PVA prepared from PVPi polymerized at lower temperatures in TBA. Moreover, PVA from the TBA system was fibrous, with a high degree of orientation of the crystallites, indicating the syndiotactic nature of TBA polymerization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1992–2003, 2002     

Transition of hydration states of poly(vinyl alcohol) in aqueous solution

A straightforward method for determination of the hydration number of polymer in aqueous solution based on ice-melting technique of DSC is proposed. The simple yet precise method has been applied to determine the hydration number of poly(vinyl alcohol) (PVA) in aqueous solution covering a wide range of concentrations, from 0.005 to 0.3 g(solute)/g(solution), for three samples with different molar masses. The hydration number of PVA maintains a constant lower value of 2.5 when the concentration exceeds 0.2 g(solute)/g(solution). It increases to a value of 7 when the concentration decreases to the overlap concentration C^∗ of the polymer, where C^∗ was estimated as the reciprocal of its intrinsic viscosity. For solutions of C < C^∗, the hydration number keeps constant again at the value of 7. This behavior evidently demonstrates that PVA has two hydration states, one occurs at the dilute regime and the other occurs at concentrated regime. The concentration dependent transition from one state to another is treated mathematically by a quantitative formula which involves two parameters: one denotes the transition concentration and the other denotes the width of the transition region. The transition concentration decreases linearly with increasing molar mass resembling the behavior of molar mass dependence of overlap concentration. The structural features for the two states of hydrated PVA are briefly discussed.     

稀乙酸对聚乙烯醇水溶液静电纺丝性能的影响

采用质量分数3%乙酸水溶液作为高醇解度聚乙烯醇(PVA)的溶剂,研究了PVA稀乙酸溶液的性质及其静电纺丝工艺。结果表明:加入质量分数3%乙酸,PVA溶液粘度下降,表面张力及电导率提高;纺丝液浓度对PVA稀乙酸溶液的静电纺丝性能影响最大;当PVA稀乙酸溶液质量分数为8%～13%,固化距离15mm,纺丝电压14～18kV时,可制得形态良好的PVA超细纤维无纺毡。     

Poly(vinyl alcohol) and poly(vinyl amine) blend membranes for isopropanol dehydration

Blended membranes of hydrophilic polymers poly(vinyl alcohol) (PVA) and poly(vinyl amine) (PVAm) were prepared and crosslinked with glutaraldehyde. The prepared membranes were characterized using infrared (attenuated total reflection mode) spectroscopy, differential scanning calorimetry, X‐ray diffractometry, and scanning electron microscopy measurements. Pervaporation performances of the membranes were evaluated for the separation of water‐isopropanol (IPA) mixtures. As the PVAm content increased from PVAm0 to PVAm1.5, the flux through a 70 μm film increased from 0.023 to 0.10 kg/m² h at an IPA/water feed ratio of 85/15 at 30 °C. The driving force for permeation of water increased due to the temperature but it has no effect on IPA permeation. Activation energies for the permeation of IPA and water were calculated to be 17.11 and 12.46 kJ/mol, respectively. Controlling the thickness of the blend membrane could improve the permeation flux with only a marginal reduction in the separation factor. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45572.     

Properties of branched and network poly(vinyl alcohols) prepared with poly(vinyl alcohol) having aldehyde groups at the chain ends

Branched and network poly(vinyl alcohols) (PVAs) were prepared with inter-acetalization of the PVA with aldehyde groups at the chain ends which was prepared by the cleavage of 1,2 glycol bonds in commercial PVA. The numbers of branches estimated from molecular weights were compared with those estimated by theory. Huggins' constant and crystallinity decreased with increasing branch number. Dissolution of branched PVAs into dimethylsulphoxide was not so easy compared with commercial PVA. The colour of branched PVA–iodine complex decreased rapidly with standing while that of commercial PVA decreased gradually. Network PVAs with Young's modulus of 1–8 MPa were prepared.     

Synthesis of high-molecular weight poly(vinyl alcohol) by low-temperature emulsifier-free emulsion polymerization of vinyl acetate and saponification

High-molecular weight (HMW) poly(vinyl alcohol) (PVA) was prepared via an emulsifier-free emulsion polymerization of vinyl acetate (VAc) using a redox initiation system in low temperatures, and the subsequent saponification with potassium hydroxide in methanol. The effect of the polymerization conditions on the conversion, molecular weight, and branching degree was investigated. PVA with maximum viscosity-average degree of polymerization (DP) of 8270 could be prepared by saponification of poly(vinyl acetate) (PVAc), with DP of 10,660 obtained at temperature of 10°C, monomer concentration of 30%, potassium persulfate molar ratio to monomer of 1/2000, agitation speed of 160 rpm. The conversion was above 90%. From the emulsifier-free emulsion polymerization of VAc in low temperature, PVAc with HMW and high linearity was effectively prepared, which might be useful for the preparation of high-strength and high-modulus PVA fiber. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/waterborne polyurethane nanofiber membranes in aqueous solution

Poly(vinyl alcohol) (PVA)/waterborne polyurethane (WBPU) nanofiber mats were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy (SEM), X‐ray diffraction (XRD), thermal gravimetric analyzer (TGA), and tensile strength testing machine (ZWICK) were used to characterize the morphology and properties of the PVA/WBPU nanofiber mats. The results showed that the morphologies of PVA/WBPU nanofiber mats changed with the total solid concentration and the mass ratio of PVA/WBPU in the spinning solution. The tensile strength and thermal stability of the fibers could be significantly affected by the WBPU contents. The electrospun PVA/WBPU membranes showed higher water uptake, which would have potential applications in wound dressings. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly(ethylene oxide), poly(vinyl alcohol), and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water present in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2147–2157, 1998     

辐照法制备聚乙烯醇水凝胶研究进展

简要评述了聚乙烯醇水凝胶的制备方法,分析了各种方法的优点和缺点,介绍聚乙烯醇辐照交联的基本原理,并展望了辐射交联聚乙烯醇水凝胶研究及应用前景.     

Surface grafting of a poly(organophosphazene) onto poly(vinyl alcohol) and poly(ethylene-co-vinyl alcohol) using triethoxysilane as a coupling agent

Triethoxysilane HSi(OEt)₃ was used as coupling agent to graft a poly(organophosphazene) (POPZ) containing allylic functions to the surface of poly(vinyl alcohol) or poly(ethylene-co-vinyl alcohol) films. Hydrolyzed HSi(OEt)₃, which contained both inorganic (Si–OH) and organic (Si–H) reactivities, acted at the interface between the hydroxylated substrates (via a condensation reaction) and the allylic functions in POPZ (via a hydrosilylation reaction). Starting materials and grafting surfaces were studied by ATR-IR and XPS spectroscopies and contact angle measurements. Data obtained indicated that different POPZ layers were produced, depending on whether the functionalization of materials with silane, and the grafting reaction were separately or simultaneously made. The POPZ layer thickness was higher when the grafting reaction was preceded by the POPZ functionalization. In each cases, the modified surfaces showed marked increases in hydrophobicity character. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1965–1974, 1998