Study on the properties of crosslinking of poly(ethylene oxide) and hydroxyapatite–poly(ethylene oxide) composite

This study covers the crosslinking of poly(ethylene oxide) (PEO) and its composite with calcium hydroxyapatite (HA), their mechanical and swelling properties, and morphology. Sheets of the composites of PEO (two different grades with M_v: 5 × 10⁶ and 2 × 10⁵) and HA and neat PEO were prepared by compression molding. The prepared composite and PEO (0.1‐mm‐thick) sheets were crosslinked with exposure of UV‐irradiation in the presence of a photoinitiator, acetophenone (AP). This simple method for crosslinking, induced by UV‐irradiation in the presence of AP, yielded PEO with gel content up to 90%. Gel content, equilibrium swelling ratio, and mechanical and morphological properties of the low molecular weight polyethylene oxide (LMPEO)–HA crosslinked and uncrosslinked composites were evaluated. Although the inclusion of HA into LMPEO inhibits the extent of crosslinking, the LMPEO–HA composite with 20% HA by weight shows the highest gel content, with appreciable equilibrium swelling and mechanical strength. The growth of HA in simulated body fluid solutions on fractured surfaces of LMPEO and also LMPEO–HA was found to be very favorable within short times. The dimensional stability of these samples was found to be satisfactory after swelling and deposition experiments. The good compatibility between the filler hydroxyapatite and poly(ethylene oxide) makes this composite a useful tissue‐adhesive material. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 488–496, 2003     

High molecular weight poly( -lactide) and poly(ethylene oxide) blends: thermal characterization and physical properties

The miscibility of high molecular weight poly( -lactide) PLLA with high molecular weight poly(ethylene oxide) PEO was studied by differential scanning calorimetry. All blends containing up to 50 weight% PEO showed single glass transition temperatures. The PLLA and PEO melting temperatures were found to decrease on blending, the equilibrium melting points of PLLA in these blends decreased with increasing PEO fractions. These results suggest the miscibility of PLLA and PEO in the amorphous phase. Mechanical properties of blends with up to 20 weight% PEO were also studied. Changes in mechanical properties were small in blends with less than 10 weight% PEO. At higher PEO concentrations the materials became very flexible, an elongation at break of more than 500% was observed for a blend with 20 weight% PEO. Hydrolytic degradation up to 30 days of the blends showed only a small variation in tensile strength at PEO concentrations less than 15 weight%. As a result of the increased hydrophilicity, however, the blends swelled. Mass loss upon degradation was attributed to partial dissolution of the PEO fraction and to an increased rate of degradation of the PLLA fraction. Significant differences in degradation behaviour between PLLA/PEO blends and (PLLA/PEO/PLLA) triblock-copolymers were observed.     

Study of the miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) blends

The miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) (PEO/PVA) blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarizing optical microscopy. Because the glass‐transition temperature of PVA was near the melting point of PEO crystalline, an uncommon DSC procedure was used to determine the glass‐transition temperature of the PVA‐rich phase. From the DSC and DMA results, two glass‐transition temperatures, which corresponded to the PEO‐rich phase and the PVA‐rich phase, were observed. It was an important criterion to indicate that a blend was immiscible. It was also found that the preparation method of samples influenced the morphology and crystallization behaviors of PEO/PVA blends. The domain size of the disperse phase (PVA‐rich) for the solution‐cast blends was much larger than that for the coprecipitated blends. The crystallinity, spherulitic morphology, and isothermal crystallization behavior of PEO in the solution‐cast blends were similar to those of the neat PEO. On the contrary, these properties in the coprecipitated blends were different from those of the neat PEO. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1562–1568, 2004     

Solution and solid state nuclear magnetic resonance investigation of poly(methylmethacrylate)/ poly(ethylene oxide) blends

It is well known that nuclear magnetic resonance spectroscopy (NMR) is a powerful method to characterize blends compatibility at the molecular level. In this work binary blends formed by poly(methylmethacrylate)/poly(ethylene oxide), PMMA/PEO, were investigated by different solution and solid state NMR techniques to obtain information on blends homogeneity and compatibility. It was characterized that the values of T₁^Hρ obtained by variable contact time and delayed contact time experiments, for each composition, were distinct and this fact suggests that regions with different molecular mobilities exist, as a consequence of blending interaction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2955–2958, 2003     

Crystallization of poly(ethylene oxide) in i-polypropylene–poly(ethylene oxide) blends

A two-stage stable system of isotactic polypropylene–poly(ethylene oxide) blend, in which poly(ethylene oxide) can be permanent either in molten or in crystallized states in the temperature range from 280 to 327 K, was described. The behavior of that blend was explained in terms of fractionated crystallization. A fine dispersion of poly(ethylene oxide) inclusions is required for efficient suppression of crystallization initiated by heterogeneous nuclei. The application of a thin film of polypropylene-poly(ethylene oxide) 9 : 1 blend obtained by quenching for multiuse erasable and rewritable carriers for visible information has been demonstrated. The same sample exhibits different dynamic mechanical properties when poly(ethylene oxide) inclusions are molten or crystallized. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2047–2057, 1997     

Influence of composition and molecular mass on the morphology,crystallization and melting behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends

Results are reported on the influence of composition and molecular mass of components on the isothermal growth rate of spherulites, on the overall kinetic rate constant, on the primary nucleation and on the thermal behaviour of poly(ethylene oxide)/poly(methyl methacrylate) blends. The growth rate of PEO spherulites as well as the observed equilibrium melting temperatures decrease, for a given T_c or ΔT, with the increase of PMMA content.Such observations are interpreted by assuming that the polymers are compatible in the undercooled melt, at least in the range of crystallization temperatures investigated. Thermodynamic quantities such as the surface free energy of folding σ_e and the Flory-Huggins parameter χ₁₂ have been obtained by studying the dependence of the radial growth rate G and of the overall kinetic rate constant K from temperature and composition and the dependence of the equilibrium melting temperature depression ΔT_m upon composition, respectively.     

NMR study of poly(vinylpyrrolidone)/poly(ethylene oxide) blends

Development of polymeric blends has become very important for polymer industries because they have been shown to be successful and versatile alternatives to obtain new polymers. In this work binary blends formed by poly(vinylpyrrolidone) (PVP) and poly(ethylene oxide) (PEO) were studied by solution and solid‐state NMR to determine their physical interaction, homogeneity, and compatibility for use as membranes to separate water/alcohol. The NMR results allowed us to acquire information on the microstructure and molecular dynamic behavior of polymer blends. From the NMR solution it was possible to evaluate the microstructure: PVP presented a preferential syndiotactic distribution sequence and PEO presented two regions, one crystalline and the other amorphous. Considering the solid‐state NMR results it was possible to evaluate the molecular dynamics and all binary blends, showing that PEO behaves as a plasticizer; some intermolecular interaction was also observed. An important point was to evaluate the microstructure of the carbonyl PVP using cross polarization/magic‐angle spinning (CP/MAS) and CP/MAS/dipolar decoupling that was not observed before. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2820–2823, 2002     

Melting behaviour of poly(butylene succinate) in miscible blends with poly(ethylene oxide)

The melting behavior of poly(butylene succinate) (PBSU) in miscible blends with poly(ethylene oxide) (PEO), which is a newly found polymer blends of two crystalline polymers by our group, has been investigated by conventional differential scanning calorimetry (DSC). It was found that PBSU showed double melting behavior after isothermal crystallization from the melt under certain crystallization conditions, which was explained by the model of melting, recrystallization and remelting. The influence of the blend composition, crystallization temperature and scanning rate on the melting behavior of PBSU has been studied extensively. With increasing any of the PEO composition, crystallization temperature and scanning rate, the recrystallization of PBSU was inhibited. Furthermore, temperature modulated differential scanning calorimetry (TMDSC) was also employed in this work to investigate the melting behavior of PBSU in PBSU/PEO blends due to its advantage in the separation of exotherms (including crystallization and recrystallization) from reversible meltings (including the melting of the crystals originally existed prior to the DSC scan and the melting of the crystals formed through the recrystallization during the DSC scan). The TMDSC experiments gave a direct evidence of this melting, recrystallization and remelting model to explain the multiple melting behavior of PBSU in PBSU/PEO blends.     

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly(ethylene oxide), poly(vinyl alcohol), and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water present in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2147–2157, 1998     

Miscibility of polystyrene with poly(ethylene oxide) and poly(ethylene glycol)

The intrinsic viscosity of polystyrene–poly(ethylene oxide) (PS–PEO) and PS–poly(ethylene glycol) (PEG) blends have been measured in benzene as a function of blend composition for various molecular weights of PEO and PEG at 303.15 K. The compatibility of polymer pairs in solution were determined on the basis of the interaction parameter term, Δb, and the difference between the experimental and theoretical weight-average intrinsic viscosities of the two polymers, Δ[η]. The theoretical weight-average intrinsic viscosities were calculated by interpolation of the individual intrinsic viscosities of the blend components. The compatibility data based on [η] determined by a single specific viscosity measurement, as a quick method for the determination of the intrinsic viscosity, were compared with that obtained from [η] determined via the Huggins equation. The effect of molecular weights of the blend components and the polymer structure on the extent of compatibility was studied. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1471–1482, 1998     

PEN/PET共混物结晶行为研究

用差示扫描量热法(DSC)研究了不同共混比例PEN/PET共混物的熔体结晶行为,并进行了等温结晶动力学测定。结果表明:随着两种组分向中间比例(50/50)靠近,共混物的熔融温度越低,结晶速率也越慢。     

Miscibility and crystallization of poly(ethylene oxide) and poly(ε-caprolactone) blends

Blends of poly(ethylene oxide) (PEO) with poly(ε-caprolactone) (PCL), both semicrystalline polymers, were prepared by co-dissolving the two polyesters in chloroform and casting the mixture. Phase contrast microscopy was used to probe the miscibility of PEOB/PCL blends. Experimental results indicated that PEO was immiscible with PCL because the melt was biphasic. Crystallization of PEO/PCL blends was studied by differential scanning calorimetry and analyzed by the Avrami equation. The crystallization rate of PEO decreased with the increase of PCL in the blends while the crystallization mechanism did not change. In the case of the isothermal crystallization of PCL, the crystallization mechanism did not change, and the change in the crystallization rate was not very big, or almost constant with the addition of PEO, compared with the change of the crystallization rate of PEO.     

First results of small and wide angle X-ray scattering of poly(ethylene oxide)/poly(methyl methacrylate) binary blends

Some preliminary small and wide angle X-ray scattering results are reported from isothermally crystallized samples of poly(ethylene oxide)/(methyl methacrylate) binary blends.     

Spherulitic crystallization in blends of poly(ethylene oxide) and poly(methyl methacrylate)

The crystallization kinetics of binary blends of poly(ethylene oxide) and poly(methyl methacrylate) were investigated. The isothermal spherulitic growth rates were measured by means of a polarized light microscope. The temperature and composition dependence on the growth rates have been analysed. The temperature range studied was from 44° to 58°C. The introduction of poly(methyl methacrylate) into poly(ethylene oxide) resulted in a reduction of the spherulitic growth rate as the proportion of poly(methyl methacrylate) was increased from zero to 40% by weight. Results have been analysed using the theoretical equations of Boon and Azcue for the growth rate of polymer-diluent mixtures. The experimental results are in good agreement with this equation. The temperature coefficient is negative as is the case in the crystallization of bulk homopolymers.     

Ultraviolet-induced crosslinking of solid poly(ethylene oxide)

Poly(ethylene oxide) (PEO) of molecular weight from 200,000 to 2,000,000 was crosslinked by exposure to ultraviolet radiation with a high-pressure 150 W mercury lamp. Photochemical crosslinking of PEO proceeds in the presence of photoinitiators such as benzophenone and acetophenone which act as a hydrogen-abstracting agent. Gel fraction yield exceeds 90%, and the number-average molecular weight between crosslinks determined by equilibrium swelling in chloroform varies from 3,000 to 100,000. The degree of crosslinking can be controlled by changing the irradiation temperature. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2299–2307, 1997     

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide) and poly(propylene oxide)

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide (PEO) and poly(propylene oxide) (PPO) was evaluated by building up temperature-concentration phase diagrams. We have studied bifunctional triblock copolymers (HO-PEO-PPO-PEO-OH) and monofunctional diblock copolymers (R-PEO-PPO-OH and R-PPO-PEO-OH, where R length is linear C₄ and C_12–14). The cloud points of the polymer solutions depended on EO/PO ratio, polarity, R length and position of the hydrophilic and hydrophobic segments along the molecule. Such factors influence on the solutions behavior was also analyzed in terms of critical micelle concentration (CMC), which was obtained from surface tension vs. concentration plots. Salts (NaCl and KCl) added into the polymer solutions change the solvent polarity decreasing the cloud points. On the other hand, the cloud points of the polymer solutions increased as a hydrotrope (sodium p-toluenesulfonate) was added. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1767–1772, 1997     

Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997     

Poly(vinyl alcohol)-clay and poly(ethylene oxide)-clay blends prepared using water as solvent

Montmorillonite (MON) was solvent-cast blended with poly(vinyl alcohol) (PVA) and poly(ethylene oxide) (PEO) using water as cosolvent. The structure and properties of the blend films have been investigated. From small- and wide-angle X-ray scattering measurements of the blends, the silicate layers of MON are found to be well dispersed individually in the PVA-MON blends, while the silicate layers in PEO-MON blends are found to exist in the form of a large clay tactoid. Furthermore, for both blends, it is found that the silicate layers are parallel to the film surface of the blends, and that preferred orientation of polymer crystallites is induced by the presence of MON. The effects of the MON content on the thermal behavior of the PVA- and PEO-MON blends have been studied with a differential scanning calorimeter. Furthermore, the effects of geometry of the silicate layers on dynamic behavior of the blends have been studied. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 573–581, 1997     

Crystalline and thermal behavior of poly(ethylene terephthalate)/polyphenoxy blends

Poly(ethylene terephthalate) (PET)/polyphenoxy blends were prepared by melt blending. Crystalline and thermal behaviors of PET/polyphenoxy blends were verified by use of DSC. The experiment results show that the initial temperature, peak temperature, and ending temperature of cold crystallization increase with increasing phenoxy content. On the contrary, the onset melting temperature, finishing melting temperature, and peak temperature in the first heating and the secondary heating processes decrease with increasing phenoxy content. The crystallization enthalpy and melting enthalpy, as well as the crystallization rate, decrease with increasing phenoxy content. Avrami exponents of the blends are slightly higher than that of pure PET and almost independent of phenoxy content. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 878–885, 2005     

Ionic conductivities for poly(ethylene oxide) complexes with lithium salts of monobasic and dibasic acids and blends of poly(ethylene oxide) with lithium salts of anionic polymers

Lithium salts of two polyanionic addition polymers containing alkyl sulphonic acid and perfluoroalkyl carboxylic acid side groups were prepared. Blends of these polymers were formed with poly(ethylene oxide) (PEO). The blend containing alkyl sulphonate units showed some phase separation but this was not observed for the blend containing perfluoroalkyl carboxylate groups. In the latter case a comparatively high conductivity of $\text{～10}{}^{\mathrm{?5}}\text{Ω}{}^{\mathrm{?1}}$ cm^?1 at 374 K was obtained. The anionic units in these blends are expected to be virtually immobile. Complexes formed from PEO and the Li-salt of hexafluoroglutaric acid had similar high ionic conductivities and there are grounds for supposing that the anions in these complexes may also be substantially immobilized. In addition, conductivity values were obtained for some PEO complexes containing lithium salts of some monobasic acids and it was found that the complex formed from the Li-salt of the strongest acid gave the highest conductivity ($\text{～4 × 10}{}^{\mathrm{?4}}\text{Ω}{}^{\mathrm{?1}}$ cm^?1 at 373 K for a PEO-LiSO₃CF₃ complex).