Effects of rare earth on inclusions and corrosion resistance of 10PCuRE weathering steel

The types,morphologies and distributions of nonmetallic inclusions in Cu-P weathering steels with and without rare earth were analyzed through a quantitative image analyzer,scanning electron microscopy(SEM)and energy dispersive spectroscopy(EDS)attached to SEM.Solid-soluble content of rare earth in the steels was analyzed by non-aqua electroanalysis and ICP.The results showed that rare earth modified the types and the morphologies of inclusions in the weathering steels.The small spherical rare earth oxysulfides and rare earth sulphides replaced the elongated MnS inclusions in the RE weathering steels.The rare earth inclusions dispersedly distributed and most inclusions were smaller than 2 μm in size.The optimum content of RE was 0.0065%-0.016% for 10PCuRE weathering steels containing about0.002% oxygen and 0.004% sulfur.Solid-soluble content of rare earth in steels was(14-20)x 10-6,which can act as a micro-alloying element.The corrosion resistance of 10PCuRE weathering steels and Q235 were studied by dry-wet cyclic immersion test.Their corrosion rates were obtained respectively.The polarization curves and pitting corrosion behaviors of weathering steels with and without rare earth were measured by electrochemical methods.The corrosion resistance of Cu-P weathering steels was improved by adding an appropriate amount of rare earth.Less and fewer rare earth inclusions largely decreased pitting susceptibility and rate of pit propagation.The pitting potential and the resistance against pitting corrosion of the RE weathering steel were significantly improved due to the modification of rare earth to inclusions.     

Lanthanide NIR luminescence for telecommunications, bioanalyses and solar energy conversion

Present-day advanced technologies heavily rely on the exciting magnetic and spectroscopic properties of lanthanide ions. In particular, their ability to generate well-characterized and intense near-infrared (NIR) luminescence is exploited in any modern fiber-optic telecommunication network. In this feature article, we first summarize the whereabouts underlying the design of highly luminescent NIR molecular edifices and materials. We then focus on describing the main trends in three applications related to this spectral range: telecommunications, biosciences, and solar energy conversion. In telecommunications, efforts concentrate presently on getting easily processable polymer-based waveguide amplifiers. Upconversion nanophosphors emitting in the visible after NIR excitation are now ubiquitous in many bioanalyses while their application to bio-imaging is still in its early stages; however, highly sensitive NIR-NIR systems start to be at hand for both in vitro and in vivo imaging, as well as dual probes combining magnetic resonance and optical imaging. Finally, both silicon-based and dye-sensitized solar cells benefit from the downconversion and upconversion capabilities of lanthanide ions to harvest UV and NIR solar light and to boost the overall quantum efficiency of these next-generation devices.     

Evaluation of D113 cation exchange resin for the removal of Eu(Ⅲ) from aqueous solution

Batch adsorption experiments were conducted for the adsorption of Eu(Ⅲ) ions from aqueous solution by D113 resin. The results indicated that D113 resin could adsorb Eu(Ⅲ) ion effectively from aqueous solution. The adsorption was strongly dependent on pH of the medium with enhanced adsorption as the pH turned from 3.50 to 7.00 and the optimal adsorption condition was in HAc-NaAc medium with pH value of 6.50. The maximum uptake capacity of Eu(Ⅲ) ions was 290.9 mg/g D113 at 298 K, at an initial pH value of 6.50. The overall adsorption process was best described by Lagergren-first-order kinetics. When Freundlich and Langmuir isotherms were tested, the latter had a better fit with the experimental data. The thermodynamic parameters such as free energy (G) which were all negative, indicated that the adsorption of Eu(Ⅲ) ions onto D113 resin was spontaneous and the positive value of enthalpy (H) showed that the adsorption was endothermic in nature. Thomas model was applied to experimental column data to determine the characteristic parameters of column useful for process design. Furthermore, Eu(Ⅲ) could be eluted by using 3.0 mol/L HCl solution and the D113 resin could be regenerated and reused.     

Phase structure and temperature dependent luminescence properties of Sr2LiSiO4F: Eu2+ and Sr2MgSi2O7: Eu2+ phosphors

Green-emitting Sr2LiSiO4F:Eu2+ and blue-emitting Sr2MgSi2O7:Eu2+ phosphors were synthesized by the conventional high temperature solid-state route,respectively.Their structures and photoluminescenee properties were comparatively investigated.It was found that the mixture phases of Sr2MgSi2O7 and SrF2 were obtained when a part of Sr2+ in Sr2LiSiO4F was replaced by some amount of Mg2+ in order to design the possible SrMgLiSiO4F:Eu2+ phosphor.Based on the photoluminescence analysis,Sr2LiSiO4F:Eu2+ phosphor exhibited a green broad emission band of main peak at 513 nm under the excitation of 365 nm,while the Sr2MgSi2O7:Eu2+ and SrMgLiSiO4F:Eu2+ phosphor showed blue emission centered at 467 nm.The temperature dependent photoluminescence properties and room temperature decay time for the three kinds of phosphors were also discussed in this paper.     

Er3+-substituted W-type barium ferrite: preparation and electromagnetic properties

Er3+-substituted W-type barium ferrites Ba1-xErx(Zn0.3Co0.7)2Fe16O27(x=0.00,0.05,0.10,0.15,0.20)were synthesized by polymer adsorbent combustion method.Samples were characterized by X-ray diffraction analysis(XRD),X-ray fluorescence(XRF),scanning electron microscopy(SEM)and network analyzer to investigate the relationships among Er3+concentration,crystal structure,surface mcrphology and electromagnetic properties.All the XRD patterns showed pure phase of W-type barium ferrite when x≤0.15,while the impurity phase of ErFeO3 appeared when x=0.20.The pure W-type barium ferrite showed a hexagonal flake shape.In addition,the microwave electromagnetic properties of samples were analyzed in the frequency range of 2-18 GHz.It was indicated that the electromagnetic properties were significantly improved when Er3+doping content was 0.10.The reasons were also discussed using electromagnetic theory.The optimized ferrite exhibited excellent microwave absoption performance.The maximum of reflection loss(RL)reached about-27.4 dB and RL was below-10dB at the frequency range from 8.4 GHz to 18 GHz,when the thickness was 2.6 mm.     

EXAFS investigation and luminescent properties of nanosized Tb: Lu2O3 phosphors

Nanosized terbium doped Lu2O3 phosphors were synthesized via a modified co-precipitation processing.The as-prepared Tb:Lu2O3 phosphors was consisted of well crystallized nanosized sphere particles with a diameter of about 30 nnx Local structure of Tb ions in Lu2O3 lattice was investigated by an analytical approach based on Fourier transformation of the extended X-ray absorption fine structure(EXAFS) data.X-ray near edge structure (XANES) spectra suggested that all Tb ions doped were tervalonce.EXAFS results indicated that Tb ions have entered the Lu2O3 cubic lattice by means of solid solution.The coordination number and first shell Tb-O distance dropped with the increasing of Tb concentration.Emission spectra of the phosphors was shown to be typical for Tb3+ with main components at 542,550 and 490 nm,derived from irradiative relaxation of 5D4 level.The emission intensity decreased severely with the increasing of Tb concentration from 1 mol.% to 15 tool.%,suggesting a significant concentration quenching above 1 mol.% Tb.The reduction of emission intensity was interpreted by higher distortion derived relaxation among the surface state resident Tb3+ ions.     

Multi-Pass Simulation of Heavy Plate Rolling Including Intermediate Forced Cooling

Thermomechanical Controlled Processing (TMCP) including accelerated cooling after the final hot rolling pass is a well-established technology,widely applied in HSLA steel plate production.However,there are still certain limitations,especially for thicker plate.The rolling schedule includes a long holding period (HP) after the roughing stage to allow the temperature to fall sufficiently for optimised TMCP during finishing.Intermediate Forced Cooling (IFC) applied during the HP can increase productivity by decreasing the required hold time,can restrict austenite grain growth,and can also improve the subsequent strain penetration in thick plate with further metallurgical benefits.Multi-pass plane strain compression (PSC) tests have been performed on the thermomechanical compression (TMC) machine at Sheffield University including different severities of IFC.Clearly it is impossible to simulate all aspects of the temperature and strain gradients present in thick plates in laboratory specimens,and most of the tests were conducted at temperatures and strains calculated by Finite Element modelling as relevant to specific positions through the plate thickness.However,some aspects of the gradients were addressed with tests using cold platens.The results have indeed shown that IFC can shorten the HP and reduce austenite grain growth and its variation across thick plate.     

Overview of Particles and Bubbles in Continuously Cast Steel

This paper gives an overview of phenomena associated with particles and bubbles in continuously cast steel. During steel processing from deoxidation to solidification the inclusion population undergoes changes with opportunities of removal. Flotation is an important separation mechanism. Inclusion particles may accumulate in the solidifying strand, thus forming enriched bands, which depend on the type of casting machine. Bubbles are created during inert gas injection. They also change in size, can float out, but also form accumulation bands. The interaction of bubbles and particles is discussed. Internal structure that recently has been observed on the inner surface of bubbles will be reviewed.     

烦恼 快乐 艺术——池莉“人生三部曲”解读

池莉的"人生三部曲"--<烦恼人生>、<不谈爱情>、<太阳出世>诉尽了普普通通的市民烦恼,小说中主人公被柴米油盐、吃喝拉撒、老婆孩子等琐事所烦着,从而构成他们的"烦恼人生".然而池莉通过自己的艺术创作,以积极的人生态度,又让读者体会到生活本身的快乐,"烦恼人生"中包含着"快乐人生".     

属性块在工程图形中的研究与应用

介绍了在工程图形中用属性块标注表面粗糙度的方法.采用属性块不仅能避免大量重复性的工作,还能节省大量的存储空间,具有提高绘图速度、质量,便于修改,资源共享等应用价值.     

优化锰铁高炉配矿结构

介绍了新钢锰铁高炉通过优化烧结矿原料结构，改善了烧结矿性能，使锰铁冶炼取得了增产、节焦、降成本的明显效果。     

韶关冶炼厂硫酸系统的技术改造

介绍了韶冶硫酸系统技术改造和改造后运行情况。改造后设备生产能力提高,有关工艺指标控制改善,并进一步改善环保排放和节能降耗。     

板式楔横轧轧件成形过程几何模拟

在对板式楔横轧轧制过程分析的基础上,建立了楔横轧入轧制和展宽轧制过程轧件变形的数学模型。探讨了轧制过程中轧件滚动半径的确定方法,对轧件端面移动理论进行了研究,建立了轧件端面移动数学模型。最后利用计算机画技术,交 轧制过程中轧件成形过程进行了模拟,实现了模拟轧制。     

宝钢炼钢经济生产组织模式的实践

为了加快炼钢生产节奏,降低炼钢过程中的能耗和物耗,分析了5个转炉生产的可行性,比较了不同的生产方案,提出了特殊钢生产时的对策。实施5个转炉生产后,每天节约用电10万kW·h以上,转炉平均出钢间隔时间减少17min,钢水平均传搁时间降低3min,实现了炼钢的经济生产。     

Viscoelastic State for the Solutions of Spherically Symmetric Viscoelasticity Problems

The solutions of the spherically symmetric, linear, isothermal, and transient viscoelasticity problems via reciprocity theorem have been investigated for a specific material. The integral form of stress–strain relations has been used. The Laplace transform of a viscoelastic state, which is necessary for the integral equation arising as a result of reciprocity theorem, has been derived. This integral equation has been solved by Laplace transform. A sample problem has been solved to test the presented formulation. A numerical application of the analytic solution of this problem has been given.     

安钢3#高炉降低综合焦比生产实践

介绍了安钢通过加强精料工作、优化高炉操作等措施，保持合理的煤气流分布，控制稳定的操作炉型，强化高炉冶炼，使高炉综合焦比大幅降低，各项经济技术指标得到改善的生产实践。     

攀钢1号高炉第三代炉役高效长寿生产实践

在攀钢1号高炉第三代炉役生产中，采取了加重边缘、适当发展中心的装料制度，缩小风口面积以增大鼓风动能的下部调剂，获得了高产的效果，保证了安全生产，有效的延长了高炉寿命。     

国产化连轧棒材线高效化生产

简要介绍南昌钢铁有限责任公司棒材生产线,采用国产化设备,运用好先进的棒材新工艺,新技术,来提高轧机的机时产量,减少消耗,降低生产成本,创造效益,实现高效化生产。     

渗稀土激光熔凝处理对纯铁表面耐磨性的影响

研究了渗稀土激光熔凝复合处理对纯铁表面耐磨性能及微观组织的影响。结果表明，经过复合处理，纯铁表面的耐磨性显著提高，磨损失重为未处理试样的5%，且纯铁表层微观组织改善，晶粒细化，组织均匀致密，渗入元素浓度梯度明显减小。     

钢包顶渣改质剂在50t LF精炼炉上的应用

本文介绍了钢包顶渣改质剂在50t LF炉精炼含铝Q345C钢的应用,结果表明：应用试验钢包顶渣改质剂后提高了铝的收得率,加强了钢液的深脱硫和脱磷,极大地降低了精炼渣中的TFe含量,改善了轧材的机械性能,降低了含铝钢的生产成本。