Decoupled output voltage control of quantum series resonantconverter for improved buck-boost operation

A new output voltage control technique is proposed to obtain the improved buck-boost operation of the quantum series resonant power converter (QSRC). The new nonlinear dynamic model of QSRC is first derived and the cross-coupled nonlinear term existing in the output voltage dynamics is decoupled by using control methods such as the periodic control of the boosting switch (PCBS) and the resonant current control (RCC). By applying the state-space averaging concept to the decoupled dynamics, two linear large signal averaged models are obtained for PCBS and RCC schemes. Using the proposed technique, the flux imbalance problem of the isolation transformer and the robustness of the output voltage response can be easily considered. This technique can also be widely applicable to the cascade buck-boost power converter, which can be implemented by inserting a boosting switch between the output filter inductor and the ripple capacitor of the forward power converter. The validity of the proposed scheme is confirmed by the computer simulations and the experiments     

Self-sustained oscillating resonant converters operating above theresonant frequency

This paper presents a new control technique for resonant converters. Unlike conventional variable frequency control which externally imposes the switching frequency, the proposed scheme is based on controlling the displacement angle between one of the resonant circuit variables, typically the current through the resonant inductor, and the voltage at the output of the inverter. As a result, zero-voltage switching (ZVS) can be ensured over a wide operating range. The proposed control technique cam be applied for series, parallel, and series-parallel resonant converters. As an example, the static characteristics and dynamic model of a series-parallel resonant converter with the proposed controller are derived and the system behaviour is investigated in detail. Experimental results are given to demonstrate the operation of resonant converters with the proposed controller and to validate the analysis     

Self-sustained phase-shift modulated resonant converters: modeling, design, and performance

This paper presents an improved control technique for the full bridge series, parallel, and series-parallel resonant converters. This control technique combines a self-sustained oscillation mode with a phase shift modulation technique that can significantly reduce the range of frequency variation necessary for obtaining zero voltage switching in the resonant converters. This frequency reduction provides optimized component ratings and operating frequency. A simple and accurate low order mathematical model based on the sampled data technique that fully describes the steady-state, and dynamic performance of the resonant converters, has been developed. A refinement algorithm is developed to enhance the accuracy of the modeling technique and the converter design. The improved converter performance and the feasibility of the developed dynamic model have been investigated using the series-parallel resonant converter topology with a capacitive output filter. Finally, MATLAB numerical solutions, PSIM simulation results, and experimental results are given to highlight the merits of the proposed work.     

Optimum Trajectory Switching Control for Series-Parallel Resonant Converter

The series-parallel resonant converter (SPRC) is known to have combined merits of the series resonant converter (SRC) and PRC. However, the SPRC has a three-element LCC structure with complex transient dynamics, and without control of the resonant circuit's dynamics, the converter's closed-loop bandwidth to switching-frequency ratio will be much reduced compared to that of pulsewidth-modulation (PWM) converters. This paper presents the optimal trajectory enabling any SPRC's steady state be achieved within one cycle. Dynamics using the state-plane analysis is presented, and the optimal state trajectory for transients is derived. Experimental results with comparison to frequency control show much reduced resonant circuit response time for step changes in output voltage. This improved resonant circuit control allows subsequent current and voltage-loop controls of the SPRC to be treated as that of a conventional PWM voltage source     

Switched optimal predictive current control technique for improved quantum boost SRC

A dynamic model and a switched optimal predictive current control technique for an improved quantum boost series resonant convertor (SRC) are proposed to overcome the inherent disadvantages of the quantum SRC. With this technique, the current ripple and the overshoot can be minimised and the buck-boost operation can also be achieved.<>     

Generalized Optimal Trajectory Control for Closed Loop Control of Series-Parallel Resonant Converter

The series parallel resonant converter (SPRC) is known to have combined the merits of the series resonant converter (SRC) and the parallel resonant converter (PRC). However, the series PRC (SPRC) has a three-element LCC structure with complex transient dynamics and without control of the resonant circuit's dynamics, the converter's closed loop bandwidth to switching frequency ratio will be much reduced compared to that of pulsewidth modulation converters. In this paper, the generalized optimal trajectory control (GOTC) for the SPRC is presented. It allows the nonlinear resonant circuit of the SPRC having an arbitrary starting state to reach a desired steady state in one cycle with two optimally controlled switching instances. It is a generalized form of optimal trajectory control (OTC) which is restricted to transitions between steady states. Based on GOTC, a traditional controller with inner current and outer voltage state-feedback is designed for an SPRC based dc–dc converter. The GOTC based feedback controller allows use of higher feedback gains compared with one using OTC or frequency control and gives higher closed loop bandwidth. This results in either better disturbance rejection for the converter or the possibility of reducing output filter sizing. Experimental results confirm the theoretical claims.     

A Three-Level Resonant Single-Stage Power Factor Correction Converter: Analysis, Design, and Implementation

This paper presents a new single-stage power factor correction ac/dc converter based on a three-level half-bridge resonant converter topology. The proposed circuit integrates the operation of the boost power factor preregulator and the three-level resonant dc/dc converter. A variable-frequency asymmetrical pulsewidth modulation controller is proposed for this converter. This control technique is based on two integrated control loops: the output voltage is regulated by controlling the switching frequency of the resonant converter, whereas the dc-bus voltage and input current are regulated by means of duty cycle control of the boost part of the converter. This provides a regulated output voltage and a nearly constant dc-bus voltage regardless of the loading condition; this, in turn, allows using smaller switches and consequently having a lower on resistance helping to reduce conduction losses. Zero-voltage switching is also achieved for a wide range of loading and input voltage. The resulting circuit, therefore, has high conversion efficiency making it suitable for high-power wide-input-voltage-range applications. The effectiveness of this method is verified on a 2.3-kW 48-V converter with input voltage (90–265 Vrms).      

A contactless power transfer system using a series–series–parallel resonant converter

In this article, a contactless power transfer system using a series–series–parallel resonant converter (SSPRC) is proposed. The proposed converter can improve on or eliminate the disadvantages of the contactless system based on conventional resonant converters, since it independently compensates for a primary side leakage inductance, a secondary side leakage inductance and a magnetising inductance. The proposed converter also reduces the circulating currents and the reactive power by controlling the phase angle difference between the inverter output voltage and the current. In addition, the system design can be simplified, since the voltage gain is determined only by the transformer turns ratio for the overall load range without being affected by the other transformer parameters. The proposed converter is analysed with respect to the gain and current margin. The system design procedure is then described for the proposed circuit based on the circuit analysis. Finally, the experimental results are presented in order to verify the proposed contactless power supply.     

High performance series-parallel type on-line UPS

An improved single-phase uninterruptible power supply (UPS) is proposed that is composed of a series converter and a parallel converter. The series converter regulates the output voltage, and then the parallel converter provides reactive current compensation and battery charging. A fast detection technique of the line voltage is proposed, which has almost zero transition time from the line power mode to the power failure mode. Furthermore, a current controller of the parallel converter for unity power factor is suggested and it is derived using the feedback linearization technique. A current limit technique in the power failure mode is proposed to protect the parallel converter without a system trip under any impulsive load. All control algorithms are implemented in software with a single-chip microcontroller. Experimental results obtained under a 3?kVA prototype show good transient and steady-state performance such as almost negligible transition time, 97% power efficiency and 99% power factor.     

A unity power factor resonant AC/DC converter for high-frequencyspace power distribution system

This paper presents analysis and design of a resonant AC/DC converter topology, suitable for use in an advanced single-phase, sine-wave voltage, high-frequency power distribution system of the type that was proposed for a 20 kHz space station primary electrical power distribution system. The converter comprises a transformer, a double-tuned resonant network comprising of series- and parallel-tuned branches, a controlled rectifier, and an output filter. Symmetrical phase control technique that generates fundamental AC current in phase with the input voltage is employed. Steady-state analysis of the converter in continuous current mode of operation is provided, and the performance characteristics presented. The proposed converter has close-to-unity rated power factor (greater than 0.98), a wide range of output voltage control (0%-100%), low total harmonic distortion in input current (less than 8%), and high conversion efficiency. Finally, selected experimental results of a bread-board converter are presented     

Series resonant converter with auxiliary winding turns: analysis,design and implementation

Conventional series resonant converters have researched and applied for high-efficiency power units due to the benefit of its low switching losses. The main problems of series resonant converters are wide frequency variation and high circulating current. Thus, resonant converter is limited at narrow input voltage range and large input capacitor is normally adopted in commercial power units to provide the minimum hold-up time requirement when AC power is off. To overcome these problems, the resonant converter with auxiliary secondary windings are presented in this paper to achieve high voltage gain at low input voltage case such as hold-up time duration when utility power is off. Since the high voltage gain is used at low input voltage cased, the frequency variation of the proposed converter compared to the conventional resonant converter is reduced. Compared to conventional resonant converter, the hold-up time in the proposed converter is more than 40ms. The larger magnetising inductance of transformer is used to reduce the circulating current losses. Finally, a laboratory prototype is constructed and experiments are provided to verify the converter performance.     

PWM-controlled SRC with inductive output filter at constantswitching frequency

By using the PWM control scheme in the series resonant power converter (SRC) with inductive output filter, the converter can be operated at a constant frequency. This converter has lower switching loss than the PWM converter and better control characteristics than the ordinary SRC. Since the peak current in the present converter equals the load current, it has the lowest possible peak current stress among converters. The analysis and the performance characteristics of the converter operating at a constant switching frequency are presented. Experimental results are given to confirm the analytical work     

Resonant-tank control of parallel resonant converter

A control method called resonant-tank control (RTC) is proposed for a parallel resonant converter operating above resonance. Using a simple linear combination of tank variables, it has potential for high-frequency DC-DC converter applications. RTC controls the tank in a near-time-optimal manner and is shown to have better dynamics than conventional frequency control. Experimental results that confirm the superior transient performance of the RTC method are provided. The principle of operation of the RTC can be extended to operation below resonance as well as to series resonant converter control     

Real-time output voltage control method of quasi-ZCS seriesresonant HF-linked DC-AC converter

This paper proposes a real-time control method of a series resonant high-frequency linked DC-AC converter employing quasi-zero current switching (quasi-ZCS) and a feedback control method for sinusoidal output voltage. An approximate analysis of the converter is performed, and then simplified equations and an equivalent circuit similar to the conventional PWM inverters/inverters are obtained. A real-time feedback control of the converter is realized using the equivalent circuit without detecting HF link current. The usefulness of the proposed control algorithm is confirmed by experimental results     

Characteristics of load resonant converters operated in ahigh-power factor mode

The performance of the parallel resonant power converter and the combination series/parallel resonant power converter (LCC converter) when operated above resonance in a high power factor mode are determined and compared for single phase applications. When the DC voltage applied to the input of these converters is obtained from a single phase rectifier with a small DC link capacitor, a relatively high power factor inherently results, even with no active control of the input line current. This behavior is due to the pulsating nature of the DC link and the inherent capability of the converters to boost voltage during the valleys of the input AC wave. With no active control of the input line current, the power factor depends on the ratio of operating frequency to tank resonant frequency. With active control of the input line current, near-unity power factor and low-input harmonic currents can be obtained     

一种双极性电流源型功率谐振直流变换器

介绍了一种双极性电流源型谐振直流变换器，该变换器综合了串联谐振变换器和并联谐振变换器的优点，并且克服了各自的缺陷。文章运用经典交流分析法，推导了电流传输增益，同时分析了断续工作模式下的各种开关状态，得出相应的等效电路，并利用仿真结果验证了所做的理论分析。     

An improved ZCS-PWM commutation cell for IGBT's application

An improved zero-current-switching pulsewidth-modulation (ZCS-PWM) commutation cell is proposed, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches with low-current stress without voltage stress and PWM operating at constant frequency. The main advantage of this cell is a substantial reduction of the resonant current peak through the main switch during the commutation process. Therefore, the RMS current through it is very close to that observed in the hard-switching PWM converters. Also, small ratings auxiliary components can be used. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principles, theoretical analysis, design guidelines and a design example are described and verified by experimental results obtained from a prototype operating at 40 kHz, with an input voltage rated at 155 V and 1 kW output power. The measured efficiency of the improved ZCS-PWM boost converter is presented and compared with that of hard-switching boost converter and with some ZCS-PWM boost converters presented in the literature. Finally, this paper presents the application of the proposed soft-switching technique in DC-DC nonisolated power converters     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

An AC VRM topology for high frequency AC power distribution systems

In this paper, a series resonant converter with pulse-width modulation (PWM) control is presented as an ac voltage regulator module (VRM) for high frequency ac power distribution systems. The proposed topology has close-to-unity rated power factor, low total harmonic distortion in input current, zero voltage switching under all load conditions, low voltage stress of the active switch and high overall efficiency. Simulation and experimental results are presented to prove the performance of the proposed ac VRM converter.     

A novel self-oscillating, boost-derived DC-DC converter with load regulation

This paper proposes a novel self-oscillating, boost-derived (SOBD) dc-dc converter with load regulation. This proposed topology utilizes saturable cores (SCs) to offer self-oscillating and output regulation capabilities. Conventionally, the self-oscillating dc transformer (SODT) type of scheme can be implemented in a very cost-effective manner. The ideal dc transformer provides both input and output currents as pure, ripple-free dc quantities. However, the structure of an SODT-type converter will not provide regulation, and its oscillating frequency will change in accordance with the load. The proposed converter with SCs will allow output-voltage regulation to be accomplished by varying only the control current between the transformers, as occurs in a pulse-width modulation (PWM) converter. A control network that combines PWM schemes with a regenerative function is used for this converter. The optimum duty cycle is implemented to achieve low levels of input- and output-current ripples, which are characteristic of an ideal dc transformer. The oscillating frequency will spontaneously be kept near-constant, regardless of the load, without adding any auxiliary or compensation circuits. The typical voltage waveforms of the transistors are found to be close to quasisquare. The switching surges are well suppressed, and the voltage stress of the component is well clamped. The turn-on/turn-off of the switch is zero-voltage switching (ZVS), and its resonant transition can occur over a wide range of load current levels. A prototype circuit of an SOBD converter shows 86% efficiency at 48-V input, with 12-V, 100-W output, and presents an operating frequency of 100 kHz.