Study of combustion and emission characteristics of turbocharged diesel engine fuelled with dimethylether

An experimental study of a turbocharged diesel engine operating on dimethyl ether (DME) was conducted. The combustion and emission characteristics of the DME engine were investigated. The results show that the maximum torque and power of DME are greater than those of diesel, particularly at low speeds; the brake specific fuel consumption of DME is lower than that of diesel at low and middle engine speeds, and the injection delay of DME is longer than that of diesel. However, the maximum cylinder pressure, maximum pressure rise rate and combustion noises of the DME engine are lower than those of diesel. The combustion velocity of DME is faster than that of diesel, resulting in a shorter combustion duration of DME. Compared with the diesel engine, NO_x emission of the DME engine is reduced by 41.6% on ESC data. In addition, the DME engine is smoke free at any operating condition.     

车用增压二甲醚发动机燃烧和排放特性的试验研究

在一台D6114ZLQB柴油机上进行了燃用二甲醚（DME）的燃烧和排放特性的试验研究。研究结果表明：二甲醚发动机的外特性转矩特别是低速转矩比柴油机高;二甲醚喷油延迟角比柴油大,最高爆发压力、最大压力升高率、燃烧噪声比柴油低;二甲醚扩散燃烧速率比柴油快,燃烧持续期比柴油短。和柴油机相比,二甲醚发动机的NO,排放显著下降,其欧洲稳态测试循环（ESC的NOx排放比原柴油机降低41．6％;二甲醚发动机在全工况范围内碳烟排放为零。     

直喷柴油机燃用二甲醚的试验研究

在直接喷射式柴油机上进行了燃用二甲醚的试验研究,对柱塞有效行程和柱塞直径、供油提前角、喷油压力、进气涡流比、喷嘴型式等燃烧系统主要参数对发动机功率和热效率的影响进行了研究,在燃料供给系统中增加燃油输送泵,消除了气阻,发动机可以在宽广的转速和负荷范围内稳定运行,发动机热效率比原机高３％ 。在优化燃烧系统参数的基础上对示功图和排放的测量及计算表明：二甲醚发动机最高爆发压力、最大压力升高率和 Ｎ Ｏｘ 排放均低于原机,烟度排放为０。试验结果显示了直喷式柴油机燃用二甲醚在降低排放方面的优越性能。     

车用多缸直喷柴油机燃用二甲醚的燃烧和排放特性研究

开展了4缸直喷柴油机燃用二甲醚时的燃烧和排放特性的研究。结果表明，适当增加喷油器伸出缸盖底平面的距离，采用流通截面较大的喷油器，降低启喷压力，可以提高CA498发动机燃用二甲醚时的热效率。燃用二甲醚时，发动机缸内的最大爆发压力和压力升高率低于燃用柴油时的情况。二甲醚发动机在所有工况下均可实现无碳烟排放，NO，排放约为柴油机的50％，CO和HC排放与柴油机相当。试验结果表明二甲醚是一种高效、低排放、燃烧噪声低的柴油机新型代用燃料。     

Analysis of energy release and NOx emissions of a CI engine fuelled on diesel and DME

Combustion and NO_x emissions from a dimethyl ether (DME) fuelled compression ignition engine were investigated. The test engine used consisted of an unmodified two-cylinder direct injection four-stroke air cooled type. The injection timing and injector opening pressure were left unaltered from their diesel fuelling settings. Analysis of the fuel line pressure shows that due to the compressibility of DME the rate of pressure rise was lower, resulting in injection occurring later when compared to diesel injection. The maximum combustion chamber pressure was found to be higher in the case of diesel fuelling. In terms of energy release it was found that with DME this occurs later than in the case of diesel fuelling with the larger proportion occurring just after top dead centre. A comparison of NO_x emissions revealed that, at all loads tested, these were higher in the case of DME fuelling and decreased steadily with increasing speed. At the higher speeds however, the levels of NO_x monitored were noted to be less than those of their diesel counterpart. Some of the factors influencing the promotion of NO_x emissions with DME fuelling are discussed and analysed.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Performance and emission characteristics of QHCCI dimethyl ether engine

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NO _x emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NO _x , HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NO _x emission. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(3): 67–70 [译自: 内燃机工程]     

柴油机燃用二甲醚的燃烧特性

对直喷式柴油机燃用二甲醚的燃烧特性进行了研究,测量了示功图和油器针阀升程,计算了燃烧特性并与燃用柴油进行对比。结果表明,与柴油相比,发动机燃用二甲醚时的喷油延迟期延长,滞燃期缩短,最高爆发压力和最大压力升高率均低于柴油机。研究表明发动机燃用二甲醚具有良好燃烧特性。     

二甲基醚（DME）燃烧特性研究

作者在定容燃烧弹上用火焰直接成像法研究二甲基醚 (DME)燃烧过程 ,研究了 DME的滞燃期和火焰传播特性以及不同环境温度和压力对燃烧过程的影响。研究结果表明 ,DME的滞燃期比柴油短 ,燃烧室内的温度和压力升高时 ,滞燃期缩短 ;DME的着火位置靠近喷嘴一侧 ,柴油与 DME的体积相同时 ,DME的燃烧持续期比柴油短 ;DME的燃烧火焰亮度比柴油小 ,表明 DME的燃烧温度比柴油低。燃烧后期 ,燃用 DME时 ,喷嘴有明显的泄漏现象。此外 ,作者在单缸直喷式柴油机上进行了燃用 DME的燃烧特性试验研究 ,研究结果表明 ,DME的预混合燃烧放热率比柴油低 ,缸内最大爆发压力和最大压力升高率比柴油低。由于喷油持续期延长 ,DME的燃烧持续期比柴油长 ,在上止点后 80° CA出现一个较大的放热峰值。     

Study on emissions reduction of DMCC engine with oxidation catalyst

A new combustion model diesel/methanol compound combustion (DMCC) is presented, in which methanol is injected into manifold and ignited by certain amount of diesel fuel. The results showed that DMCC remarkably decreased the emission of NO_x and the smoke, but increased the emission of HC, CO and PM. However, HC, CO and NO_x were dramatically decreased with a catalytic converter, and PM was also decreased compared with that of diesel engine. The testing results illustrated that, combined with oxidation catalyst converter, DMCC could improve engine emissions. __________ Translated from Transactions of CSICE, 2006, 24(5): 402–407 [译自: 内燃机学报]     

Effects of compression ratio on the combustion characteristics of a homogeneous charge compression ignition engine

The effects of homogeneous charge compression ignition (HCCI) engine compression ratio on its combustion characteristics were studied experimentally on a modified TY1100 single cylinder engine fueled with dimethyl ether. The results show that dimethyl ether (DME) HCCI engine can work stably and can realize zero nitrogen oxides (NO_x) emission and smokeless combustion under the compression ratio of both 10.7 and 14. The combustion process has obvious two stage combustion characteristics at ɛ = 10.7 (ɛ refers to compression ratio), and the combustion beginning point is decided by the compression temperature, which varies very little with the engine load; the combustion beginning point is closely related to the engine load (concentration of mixture) with the increase in the compression temperature, and it moves forward versus crank angle with the increase in the engine load at ɛ = 14; the combustion durations are shortened with the increase in the engine load under both compression ratios. __________ Translated from Chinese Journal Combustion Engine Engineering, 2006, 27(4): 9–12 [译自: 内燃机工程]     

A numerical study on a hydrogen assisted diesel engine

This work aims to numerically study the performance, combustion and emission characteristics of a hydrogen assisted diesel engine under various operating conditions. Simulations were performed using multi-dimensional software KIVA4 coupled with CHEMKIN. The Kelvin–Helmholtz and Rayleigh–Taylor hybrid break up model was implemented to accurately model the spray development. A detailed reaction mechanism was constructed to take into account the chemical kinetics of diesel and hydrogen, and it was validated against the experimental results with 0% of hydrogen induction. Simulation results showed that at low engine speeds, the indicated thermal efficiency, in-cylinder pressure and apparent heat release rate increased significantly with the induction of hydrogen. On the other hand, at high engine speed and high load conditions, no tangible changes on the engine performance, combustion characteristics were observed. In terms of emissions, CO and soot emissions were shown to be reduced under most of the engine operating conditions. Whereas for NO_x emissions, a slight increase was observed at low engine speed of 1600 rpm.     

Research of performance and emission indicators of the compression-ignition engine powered by hydrogen - Diesel mixtures

The purpose of this study is to use the hydrogen – diesel mixture in Audi/VW 1.9 TDI turbocharged CI engine equipped with dynamometer and examine the performance and emission indicators by comparing it with sole diesel mode. The recent diesel emission scandals because of manufacturers cheating the laboratory tests, have initiated the discussions about the sustainable and environmentally friendly diesel engines. The CI engine without major engine modifications was set to operate at two speeds of 1900 rpm and 2500 rpm. At each of speed, the experiment was conducted at three BMEP: 0.4 MPa, 0.6 MPa, and 0.8 MPa. The test engine was operated using diesel fuel with amounts of 10 l/min, 20 l/min, and 30 l/min of hydrogen gas, supplied with air into intake manifold before the turbocharger. Relatively low hydrogen fraction (max. 15.74%) has effect on diesel combustion process and performance indicators at the all range of BMEP. The in-cylinder peak pressure at both speeds of 1900 rpm and 2500 rpm was lower than that with pure diesel fuel, as the small amount of hydrogen shortens the CI engine ignition delay period and decreases the rate of pressure rise. The decrease of BTE noticed, and increase of BSFC was registered with low hydrogen fraction (hydrogen amounts of 10 l/min, 20 l/min). However, with increase of hydrogen amount to 30 l/min, the BTE increased and BSFC decreased to the level, which was lower than that at the pure diesel test. The supply of hydrogen positively effects on engine emissions: the smokiness, NO_x, CO₂, CO decreased, the only hydrocarbon increased. The effect of hydrogen fraction on the combustion and emission characteristics of the diesel - hydrogen mixture was validated by AVL (Anstalt für Verbrennungskraftmaschinen List) BOOST and analysed with presentations of the main limitations and perspectives.     

Combustion characteristics of a direct-injection diesel engine fueled with Fischer-Tropsch diesel

Fischer-Tropsch (F-T) diesel fuel is characterized by a high cetane number, a near-zero sulphur content and a very low aromatic level. On the basis of the recorded incylinder pressures and injector needle lifts, the combustion characteristics of an unmodified single-cylinder direct-injection diesel engine operating on F-T diesel fuel are analyzed and compared with those of conventional diesel fuel operation. The results show that F-T diesel fuel exhibits a slightly longer injection delay and injection duration, an average of 18.7% shorter ignition delay, and a comparable total combustion duration when compared to those of conventional diesel fuel. Meanwhile, F-T diesel fuel displays an average of 26.8% lower peak value of premixed burning rate and a higher peak value of diffusive burning rate. In addition, the F-T diesel engine has a slightly lower peak combustion pressure, a far lower rate of pressure rise, and a lower mechanical load and combustion noise than the conventional diesel engine. The brake specific fuel consumption is lower and the effective thermal efficiency is higher for F-T diesel fuel operation. Translated from Journal of Xi’an Jiaotong University, 2006, 40(1): 5–9 [译自: 西安交通大学学报]     

Control of homogeneous charge compression ignition combustion in a two-cylinder gasoline direct injection engine with negative valve overlap

Homogeneous charge compression ignition (HCCI) has challenges in ignition timing control, combustion rate control, and operating range extension. In this paper, HCCI combustion was studied in a two-cylinder gasoline direct injection (GDI) engine with negative valve overlap (NVO). A two-stage gasoline direct injection strategy combined with negative valve overlap was used to control mixture formation and combustion. The gasoline engine could be operated in HCCI combustion mode at a speed range of 800–2 200 r/min and load, indicated mean effective pressure (IMEP) range of 0.1–0.53 MPa. The engine fuel consumption is below 240 g/(kW⁻¹·h⁻¹), and the NO _x emission is below 4 × 10⁻⁵ without soot emission. The effect of different injection strategies on HCCI combustion was studied. The experimental results indicated that the coefficient of variation of the engine cycle decreased by using NVO with two-stage direct injection; the ignition timing and combustion rate could be controlled; and the operational range of HCCI combustion could be extended. Translated from J Tsinghua Univ (Sci & Tech), 2006, 46(5): 720–723 [译自: 清华大学学报]     

Effect of hydrogen enrichment in the intake air of diesel engine fuelled with honge biodiesel blend and diesel

In the current investigation, the enrichment of hydrogen with the honge biodiesel blend and diesel is used in a compression ignition engine. The biodiesel is derived from the honge oil and mixed with diesel fuel by 20% (v/v). Thereafter, hydrogen at different volume flow rates (10 and 13 lpm) is introduced into the intake manifold. The outcomes by enrichment of hydrogen on the performance, combustion and emission characteristics are investigated by examining the brake thermal efficiency, fuel consumption, HC, CO, CO₂, NOₓ emissions, in-cylinder pressure, combustion duration, and rate of heat release. The engine fuelled with honge biodiesel blend is found to enhance the thermal efficiency, combustion characteristics. Compare to diesel, the BTE increased by 2.2% and 6% less fuel consumption for the HB20 + 13H₂ blend. Further, reduction in the emission of exhausts gases like CO and HC by 21% and 24%, respectively, are obtained. This is due to carbon-free structure in hydrogen. Moreover, due to high pressure in the cylinder, there is a slight increase in oxides of nitrogen emission compare to diesel. The combustion characteristics such as rate of heat release, combustion duration, and maximum ₂rate of pressure rise and in-cylinder pressure are high due to hydrogen.     

The effects of hydrogen addition on engine power and emission in DME premixed charge compression ignition engine

Premixed-charge compression-ignition (PCCI) combustion of dimethyl-ether (DME) with double injection strategy was investigated in a single-cylinder compression-ignition engine. DME main-injection was replaced by hydrogen to reduce carbon dioxide emissions. To study the effect of hydrogen, the injected amount of hydrogen was increased. Engine performance and emission of DME PCCI combustion were compared to those of hydrogen–DME PCCI combustion. In the DME PCCI engine operation, DME was injected directly into the cylinder at −120 crank angle degrees (°CA) after top dead center (aTDC) to simulate homogeneous charge at first, and then DME was injected secondly with varied second injection timing. In this case, DME injection timing in the second stage affected the engine performance and emissions. Delayed combustion phase showed a higher indicated mean effective pressure (IMEP), while it increased NO_x emission when DME second injection is retarded. In the hydrogen–DME PCCI, hydrogen was injected at intake port with fixed injection timing. DME injection timing in hydrogen–DME PCCI combustion was also varied from −120 °CA to TDC, as in the DME PCCI engine operation. The total supplied heating value was fixed at 400 J for all cases. DME injection timing determined the start of combustion for the hydrogen–DME PCCI. With increasing the amount of hydrogen, exhaust emissions were reduced. Hydrogen–DME PCCI engine was operated with minimum amount of DME via the hydrogen addition and DME injection timing control. The optimized DME injection timing, −30 °CA aTDC, resulted in a lower exhaust emission-operation, while maintaining a higher IMEP.     

柴油机进气掺混低浓度甲烷模拟研究

针对矿井下空气中含有甲烷气体造成柴油机在矿井下运行时会吸入甲烷的情况,使用三维计算流体动力学(CFD)软件CONVERGE模拟柴油机进气混掺0％、0.25％、0.50％、0.75％ 与1.00％ 体积浓度的甲烷气体对柴油机燃烧及排放的影响.研究结果发现,当甲烷着火时刻温度大于1000 K时,甲烷的掺混会使得羟基(OH)...     

A study on the effect of hydrogen enriched intake air on the characteristics of a diesel engine fueled with ethanol blended diesel

This work aims to replace conventional diesel fuel with low and no carbon fuels like ethanol and hydrogen to reduce the harmful emission that causes environmental degradation. Pursuant to this objective, this study investigated the performance, combustion, and emission characteristics of the diesel engine operated on dual fuel mode by ethanol-diesel blends with H₂ enriched intake air at different engine loads with a constant engine speed of 1500 rpm. The results were compared to sole diesel operation with and without H₂ enrichment. The ethanol/diesel was blended in v/v ratios of 5, 10, and 15% and tested in a diesel engine along with a 9 lpm H₂ flow rate at the intake manifold. The results revealed that 10% ethanol with 9 lpm H₂ combination gives the maximum brake thermal efficiency, which is 1% and 4.8% higher than diesel with and without H₂ enrichment, respectively. The brake specific fuel consumption of the diesel-ethanol blends with H₂ flow increased with increasing ethanol ratio in the blend. When the ethanol ratio increased from 5 to 10%, in-cylinder pressure and heat release rate were increased, whereas HC, CO, and NO_x emissions were decreased. At maximum load, the CO and HC emission of 10% ethanol blend with 9 lpm H₂ case decreased by about 50% and 28.7% compared to sole diesel. However, NO_x emission of the same blend was 11.4% higher than diesel. From the results, the study concludes that 10% ethanol blended diesel with a 9 lpm H₂ flow rate at the intake port is the best dual-fuel mode combination that gives the best engine characteristics with maximum diesel replacement.