Calorimetric study of block-copolymers of poly(n-butyl acrylate) and gradient poly(n-butyl acrylate-co-methyl methacrylate)

The nanophase separation in diblock and triblock copolymers consisting of immiscible poly(n-butyl acrylate) (block A) and gradient copolymers of methyl methacrylate (MMA) and n-butyl acrylate (nBA) (block M/A) were investigated by means of their heat capacity, C_p, as a function of the composition of the blocks M/A and temperature. In all copolymers studied, both blocks are represented by their C_p and glass transition temperature, T_g, as well as the broadening of the transition-temperature range. The low-temperature transition of the blocks A is always close to that of the pure poly(n-butyl acrylate) and is independent of the analyzed compositions of the block copolymer, but broadened asymmetrically relative to the homopolymer due to the small phase size. The higher transition is related to the glass transition of the copolymer block of composition M/A. Besides the asymmetric broadening of the transition due to the phase separation, it decreases in T_g and broadens, in addition, symmetrically with increasing acrylate content. The concentration gradient is not able to introduce a further phase separation with a third glass transition inside the M/A block.     

Synthesis of PAA-g-PNIPAM well-defined graft polymer by sequential RAFT and SET-LRP and its application in preparing size-controlled super-paramagnetic Fe3O4 nanoparticles as a stabilizer

A series of well-defined double hydrophilic graft copolymers, poly(acrylic acid)-g-poly(N-isopropylacrylamide) (PAA-g-PNIPAM), was employed as a novel water-soluble coating for constructing superparamagnetic iron oxide nanoparticles. The copolymer was synthesized via a three-step procedure: firstly, a well-defined hydrophobic PtBA-based backbone, poly(tert-butyl 2-((2-chloropropanoyloxy)-methyl)acrylate)-co-poly(tert-butyl acrylate), (PtBCPMA₁₉-co-PtBA₁₈), was prepared through RAFT copolymerization of a new trifunctional acrylic monomer, tert-butyl 2-((2-chloropropanoyloxy)methyl)acrylate and tert-butyl acrylate; secondly, taking this backbone as a macroinitiator to initiate SET-LRP of N-isopropylacrylamide resulted in well-defined (poly(tert-butyl 2-((2-chloropropanoyloxy)methyl)-acrylate)-co-poly(tert-butyl acrylate))-g-poly(N-isopropylacrylamide) ((PtBCPMA-co-PtBA)-g-PNIPAM) amphiphilic graft copolymers with relatively narrow polydispersities (M_w/M_n ≤ 1.31); thirdly, handling (PtBCPMA-co-PtBA)-g-PNIPAM in acidic conditions afforded PAA-g-PNIPAM graft copolymers. The resulting PAA-g-PNIPAM copolymers were directly utilized as a polymeric stabilizer in the preparation of superparamagnetic Fe₃O₄ nanoparticles. The particle size can be readily tuned in the range of 12.1–23.2 nm by varying the amount of PAA-g-PNIPAM copolymer or the length of PNIPAM side chain. Besides, the structure and properties of prepared Fe₃O₄/polymer nanocomposites were characterized by XRD, FT-IR, TGA, TEM, and magnetic measurement in detail.     

Block, blocky gradient and random copolymers of 2-ethylhexyl acrylate and acrylic acid by atom transfer radical polymerization

The controlled synthesis of low-T_g poly(2-ethylhexyl acrylate) (P2EHA) and derived random, block and blocky gradient copolymers via atom transfer radical polymerization (ATRP) is described. After optimizing the reaction conditions for the homopolymerization of 2EHA via ATRP, the synthesis of a variety of copolymers with poly(t-butyl acrylate) (PtBuA) was investigated. First, AB-block copolymers were targeted, starting from P2EHA and PtBuA as macroinitiators. Second, random copolymers of tBuA and 2EHA with different monomer ratios were synthesized. Finally, the synthesis of “blocky” gradient copolymers via a one-pot procedure was investigated, starting with the homopolymerization of tBuA, followed by the addition of 2EHA. The hydrolysis of the PtBuA-segments to poly(acrylic acid) (PAA), which was carried out with methanesulfonic acid, resulted in block, blocky gradient and random copolymers consisting of PAA and P2EHA. Solubility testing of the copolymers in slightly basic water (pH ∼ 9) demonstrated that the gradient structure significantly enhances solubility compared to the block copolymer structures with equal composition. The polymers have been characterized by MALDI-TOF MS, GPC and ¹H NMR.     

Grafting of end-functionalized poly(tert-butyl acrylate) to poly(ethylene-co-acrylic acid) film

Poly(tert-butyl acrylate) (PtBA) was grafted to the surface of poly(ethylene-co-acrylic acid) (EAA) film and the pendant groups of the tethered PtBA were modified to create chemically tailored surface modifying layers. The carboxylic acid groups in the copolymer film served as the grafting sites for the covalent tethering of end-functionalized PtBA. The progression of these reactions was monitored using attenuated total reflectance (ATR)-FTIR and X-ray photoelectron (XPS) spectroscopies along with static contact angle measurements. By controlling the reaction conditions, the chemical functionality of the grafted layer ranged from tert-butyl ester (EAA-g-PtBA) to carboxylic acid (EAA-g-PAA) and was demonstrated by corresponding changes in wettability. The choice of PtBA as the tethered polymer allows for the subsequent substitution of the tert-butyl ester groups. To demonstrate, a novel procedure was used to replace the tert-butyl ester with N,N-dimethylethylenediamine (DMEDA) to form EAA-g-PDMEDA. These reaction schemes can be used to create tunable surface-grafted layers with various pendant group chemistries.     

Synthesis of amphiphilic triblock copolymers and application for morphology control of calcium carbonate crystals

A series of amphiphilic triblock copolymers poly(ethylene glycol)-block-poly(acrylic acid)-block-poly(n-butyl acrylate) (PEG-b-PAA-b-PnBA) differing only in the relative block lengths were synthesized by the acid-catalyzed elimination of the tert-butyl groups from poly(ethylene glycol)-block-poly(tert-butyl acrylate)-block-poly(n-butyl acrylate) (PEG-b-PtBA-b-PnBA), which was synthesized by atom-transfer radical polymerization (ATRP). The degree of polymerization, molecular weight and percentage of hydrolysis of the product PEG-b-PAA-b-PnBA were studied by gel permeation chromatography (GPC), NMR and matrix-assisted laser desorption/ionization time-of-flight mass spectroscopy (MALDI-TOF-MS). Dynamic light scattering (DLS) and transmission electron microscopy (TEM) were used to study the aggregation states of copolymers in water solution. The radii of the copolymer micelles shrink as Ca²⁺ is introduced into the solutions. The crystallization behaviors of calcium carbonate controlled by copolymer 1 (PEG₁₁₂-b-PAA₈₆-b-PnBA₆₀) and copolymer 2 (PEG₁₁₂-b-PAA₄₀-b-PnBA₇₂) differing mainly in the length of PAA block were systematically studied. It was found that the crystallization products are composed of calcite and vaterite, and the ratio of vaterite to calcite increases with increasing the concentration of copolymer 1. For copolymer 2, however, only calcite is obtained at all the concentration range investigated in this work.     

Nitroxide-mediated polymerization to form symmetrical ABA triblock copolymers from a bidirectional alkoxyamine initiator

Bidirectional alkoxyamine 2 was synthesized and used as the initiator in the polymerization of styrene (S), n-butyl acrylate (nBA), t-butyl acrylate (tBA), isoprene (I), and dimethylacrylamide (DMA). A variety of symmetrical ABA triblock copolymers were prepared, ranging in size from 5 to 59 kDa. Kinetics studies and gel permeation chromatography (GPC) confirmed the “living” nature of these polymerizations. Trifluoroacetic acid was used to convert the PtBA blocks of these polymers into poly(acrylic acid) (PAA) blocks, forming ABA amphiphilic triblock copolymers. AFM images of PAA-b-PnBA-b-PAA and PAA-b-PS-b-PAA triblock copolymers ionized by the addition of 2,2′-(ethylenedioxy)bis(ethylamine) show evidence of self-assembly.     

Radical copolymerization of methyl 2-norbornene-2-carboxylate and 2-phenyl-2-norbornene with styrene, alkyl acrylate, and methyl methacrylate: Facile incorporation of norbornane framework into polymer main chain and its effect on glass transition temperature

Radical copolymerization behavior of methyl 2-norbornene-2-carboxylate 1 and 2-phenyl-2-norbornene 2 was investigated. Radical copolymerization of 1 and 2 with styrene, alkyl acrylate, and methyl methacrylate in a variety of monomer combinations afforded copolymers, whose main chains consisted of norbornane framework. Relative monomer reactivity ratios for the copolymerization of 1 and 2 with n-butyl acrylate (n-BA) were determined by the Fineman-Ross method. Temperature-modulated DSC analysis for poly(1 or 2-co-n-BA)s revealed remarkable T_g-raising effect of incorporation of norbornane framework into the polymer main chain, compared to that effect of styrene repeating unit.     

Amphiphilic cylindrical brushes with poly(acrylic acid) core and poly(n-butyl acrylate) shell and narrow length distribution

Core-shell cylindrical polymer brushes with poly(t-butyl acrylate)-b-poly(n-butyl acrylate) (PtBA-b-PnBA) diblock copolymer side chains were synthesized via ‘grafting from’ technique using atom transfer radical polymerization (ATRP). The formation of well-defined brushes was confirmed by GPC and ¹H NMR. Multi-angle light scattering (MALS) measurements on brushes with 240 arms show that the radius of gyration scales with the degree of polymerization of the side chains with an exponent of 0.57±0.05. The hydrolysis of the PtBA block of the side chains resulted amphiphilic cylindrical core-shell nanoparticles. In order to obtain a narrow length distribution of the brushes, the backbone, poly(2-hydroxyethyl methacrylate), was synthesized by anionic polymerization in addition to ATRP. The characteristic core-shell cylindrical structure of the brush was directly visualized on mica by scanning force microscopy (SFM). Brushes with 1500 block copolymer side chains and a length distribution of l_w/l_n=1.04 at a total length l_n=179 nm were obtained. By choosing the proper solvent in the dip-coating process on mica, the core and the shell can be visualized independently by SFM.     

Synthesis of well-defined star polymers and star block copolymers from dendrimer initiators by atom transfer radical polymerization

Novel polyarylether dendrimers with 1,3,5-tri(4-hydroxyphenoxy)benzene core, polybenzylether interior, and benzyl 2-bromoisobutyrate surface group (CMGn-Br, n=1-3, with functionality of 6, 12, and 24, respectively) were prepared by convergent procedure. ATRP of tert-butyl acrylate (tBA) and styrene (St) with CMGn-Br dendrimer initiators in the presence of CuBr/pentamethyldiethylenetriamine catalytic system was investigated in detail, and a series of well-defined dendrimer-like star PtBA and PSt with precise arm numbers were synthesized under suitable conditions. The quantitative initiation of the dendrimer initiators was demonstrated by high initiation efficiency, ¹H NMR spectra, hydrolysis, and MALLS/SEC approach. Star block copolymers comprising PSt and PtBA segments with low polydispersity (1.08<M_w/M_n<1.18) were also successfully synthesized using functional macroinitiators by block copolymerization. In addition, the thermal properties of the resultant polymers were characterized by DSC and TGA.     

Internal plasticization of poly(vinyl chloride) by grafting acrylate copolymers via copper-mediated atom transfer radical polymerization

Internal plasticization of poly(vinyl chloride) (PVC) was achieved in one-step using copper-mediated atom transfer radical polymerization to graft different ratios of random n-butyl acrylate and 2–2-(2-ethoxyethoxy)ethyl acrylate copolymers from defect sites on the PVC chain. Five graft polymers were made with different ratios of poly(butyl acrylate) (PBA) and poly(2–2-(2-ethoxyethoxy)ethyl acrylate) (P2EEA); the glass transition temperatures (T_g) of functionalized PVC polymers range from − 25 to − 50°C. Single T_g values were observed for all polymers, indicating good compatibility between PVC and grafted chains, with no evidence of microphase separation. Plasticization efficiency is higher for polyether P2EEA moieties compared with PBA components. The resultant PVC graft copolymers are thermally more stable compared to unmodified PVC. Increasing the reaction scale from 2 to 14 g produces consistent and reproducible results, suggesting this method could be applicable on an industrial scale.     

Copolymerization of pentachlorophenyl acrylate with vinyl acetate and ethyl acrylate. Polymer-bound fungicides

Copolymers of pentachlorophenyl acrylate (M₁) with both vinyl acetate and ethyl acrylate were prepared (in benzene at 60°C initiated by t-butyl peroxypivalate) at a variety of M₁/M₂ ratios. The reactivity ratios for the vinyl acetate (M₂) copolymerizations were r₁ = 1.44 and r₂ = 0.039, while for ethyl acrylate copolymerizations r₁ = 0.21 and r₂ = 0.88. The glass transition temperatures were obtained as a function of the M₁/M₂ ratio. The values of T_g for the copolymers fell between those of poly(pentachlorophenyl acrylate) and either poly(vinyl acetate) or poly(ethyl acrylate). A series of bulk copolymers with low pentachlorophenyl acrylate content were studied as biocidal coatings using accelerated growth agar dish tests inoculated with Aspergillus sp., Pseudomonas sp., Alternaria sp., and Aureobasidium pullulans. The copolymers retarded or prevented growth but did not give a zone of inhibition around the coatings. Pentachlorophenol, when added to coating polymers, did exhibit a zone of inhibition due to migration of this biocide into the agar medium.     

Carbon black‐filled poly(ethylene‐co‐alkyl acrylate) composites: Calorimetric studies

The calorimetric characteristics of carbon black (CB)/poly(ethylene‐co‐alkyl acrylate) composites depend on both the CB and acrylate contents. An increase of the acrylate content in the pure copolymers tends to decrease all the crystalline characteristics: T_c,n, the nonisothermal crystallization temperature; T_m, the melting temperature, and ΔH_m, the melting enthalpy. CB modifies the crystallization kinetics of poly(ethylene‐co‐ethyl acrylate) (EEA) alone and in blends with poly(ethylene‐co‐24% w/w methyl acrylate) (24EMA) and poly(ethylene‐co‐35% w/w methyl acrylate) (35EMA). In the presence of CB, T_c,n, the nonisothermal crystallization temperature of EEA, increases and t_1/2, the half‐crystallization time, decreases for a given isothermal crystallization temperature, T_c,i. The thermograms obtained during the melting of EEA after isothermal crystallization show multiple endotherms, suggesting that crystalline‐phase segregation has occurred. The existence of different crystalline species can be explained by the presence of fractions of different acrylate content in the copolymers as shown by SEC. Therefore, CB does not seem to have much effect on the subsequent melting temperature of EEA, T_m,s. CB also induces a lower melting enthalpy, Δ H_m, in the blends. This decrease of ΔH_m appears to be constant whatever the compound, but when reported to the melting enthalpy of the polymer without CB, δΔH_m/ΔH_m increases with the acrylate content. A slight increase of the amorphous phase stiffness after CB introduction is noticed: The T_g of EEA/24EMA and EEA/35EMA blends increases by several degrees. Therefore, plotting ΔH_m versus ΔC_p shows that for the same ΔH_m the ΔC_p is lower in CB‐filled samples, suggesting there is some kind of rigid amorphous phase not contributing to the glass transition. We propose to explain the CB activity during the crystallization process by the existence of molecular interactions between CB and acrylate groups rather than by a pure nucleating effect. Thus, the increase of T_c,n and the decrease of ΔH_m could be explained by the fact that CB separates acrylate‐rich chains from the crystallization medium, accelerating the crystallization of the acrylate‐poor chains. During such a crystallization process, CB may be preferentially localized in the more polar amorphous phase and scattered between the two crystalline phases of EEA and EXA. These blends of poly(ethylene‐co‐alkyl acrylate) copolymers with CB provide interesting materials with adjustable properties depending on the acrylate and CB contents and on the thermomechanical treatments. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 779–793, 2001     

Poly[N-(2-hydroxypropyl)methacrylamide-block-n-butyl acrylate] micelles in water/DMF mixed solvents

Three diblock copolymers of poly[N-(2-hydroxypropyl)methacrylamide] (poly(HPMA)) and poly(n-butyl acrylate) (poly(BA)) with varying lengths of blocks were prepared by atom transfer radical polymerization. All copolymers were found to be soluble in dimethylformamide (DMF) and poorly soluble or insoluble in water. In water and mixed DMF/H₂O solvents, the copolymers were dispersed in micellar form by controlled addition of water to DMF solutions of copolymers under continuous intensive stirring. The micellar solutions in water were prepared by dialysis of solutions in DMF/H₂O (95 vol% of H₂O) against water. Solution properties of diblock copolymers of poly(HPMA) and poly(BA) were studied using static and dynamic laser light scattering to characterize the behavior of the copolymers at the supramolecular level. The effects of preparation mode, organic solvent (DMF) and copolymer chemical composition on the formation of micelles were studied. While a slower mixing procedure was optimal for copolymers with short poly(HPMA) blocks, a faster mixing was more suitable for copolymers having longer poly(HPMA) blocks. Finally, the dimensions of micelles in water were evaluated. The most compact micelles were prepared from copolymers having short hydrophilic poly(HPMA) blocks. On the other hand, the copolymer with the longest poly(HPMA) block formed micelles with the smallest size and the lowest density.     

Synthesis of comb-shaped copolymers by combination of reversible addition-fragmentation chain transfer polymerization and cationic ring-opening polymerization

Comb-shaped graft copolymers with poly(methyl acrylate) as a handle were synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and ring-opening polymerization (ROP) techniques in three steps. First, copolymers of poly(styrene-co-chloromethyl styrene), poly(St-co-CMS), were prepared by RAFT copolymerization of St and CMS using 1-(ethoxycarbonyl)prop-1-yl dithiobenzoate (EPDTB) as RAFT agent. Second, the polymerization of MA using poly(St-co-CMS)-SC(S)Ph as macromolecular chain transfer agent produced block copolymer poly(St-co-CMS)-b-PMA. Third, cationic ring-opening polymerization of THF was performed using poly(St-co-CMS)-b-PMA/AgClO₄ as initiating system to produce comb-shaped copolymers. The structures of the poly(St-co-CMS), poly(St-co-CMS)-b-PMA and final comb-shaped copolymers were characterized by ¹H NMR spectroscopy and gel permeation chromatography (GPC).     

Synthesis and characterization of amphiphilic graft copolymer poly(ethylene oxide)-graft-poly(methyl acrylate)

A novel well-defined amphiphilic graft copolymer of poly(ethylene oxide) as main chain and poly(methyl acrylate) as graft chains is successfully prepared by combination of anionic copolymerization with atom transfer radical polymerization (ATRP). The glycidol is protected by ethyl vinyl ether first, then obtained 2,3-epoxypropyl-1-ethoxyethyl ether (EPEE) is copolymerized with EO by initiation of mixture of diphenylmethyl potassium and triethylene glycol to give the well-defined poly(EO-co-EPEE), the latter is deprotected in the acidic conditions, then the recovered copolymer [(poly(EO-co-Gly)] with multi-pending hydroxyls is esterified with 2-bromoisobutyryl bromide to produce the ATRP macroinitiator with multi-pending activated bromides [poly(EO-co-Gly)_(ATRP)] to initiate the polymerization of methyl acrylate (MA). The object products and intermediates are characterized by NMR, MALDI-TOF-MS, FT-IR, and SEC in detail. In solution polymerization, the molecular weight distribution of the graft copolymers is rather narrow (M_w/M_n < 1.2), and the linear dependence of Ln [M₀]/[M] on time demonstrates that the MA polymerization is well controlled.     

Control of monodisperse particle size of styrenic–acrylate copolymers in dispersion copolymerization

Syntheses of monodisperse poly[(styrene)‐co‐(n‐butyl acrylate)] and poly[(styrene)‐co‐(2‐ethylhexyl acrylate)] were carried out by dispersion polymerization. The reactions were performed in the mixed solvent of ethanol–water in the presence of azo‐bisisobutyronitrile and poly(N‐vinylpyrrolidone) as the initiator and dispersant, respectively. The effects of reaction parameters, that is the type and concentration of dispersant, ratio of the mixed solvent, reaction temperature, agitation rate, monomer composition between styrene and n‐butyl acrylate or 2‐ethylhexyl acrylate, crosslinking agent and reaction time on the particle size, size distribution and average molecular weights of the resulting copolymer were thoroughly investigated. The resulting copolymer particles were smooth on their spherical surface and the sizes were in the range 0.6–1.8 µm with a narrow size distribution. In most cases, a correlation between small particle sizes with high average molecular weights was observed. The average particle size generally increased with increasing reaction temperature, time and acrylate monomer content. In contrast, the particle size decreased as the molecular weight, concentration of dispersant, polarity of the medium or agitation rate was increased. The glass transition temperature (T_g) of the copolymers can be controlled by the mole ratio of the comonomer. The T_g values decreased when the content of acrylate monomers in the copolymer increased, and T_g values of the synthesized copolymer were in the range 66–102 °C. Instead of using n‐butyl acrylate monomer in the copolymerization, 2‐ethylhexyl acrylate copolymerization with styrene resulted in insignificant changes in the particle sizes but there were significant decreases in T_g values. In this study, the monodisperse particles can be obtained by monitoring the appropriate conditions regarding PVP K‐30 (2–8 wt%), ethanol/water (90/10 wt%), the reaction temperature (70 °C) and the agitation rate (100 rpm). © 2000 Society of Chemical Industry     

Compatibilizing effects of poly(styrene-graft-ethylene oxide) in blends of polystyrene and butyl acrylate polymers

The compatibilizing effect of poly(styrene-graft-ethylene oxide) in polystyrene (PS) blends with poly(n-butyl acrylate) (PBA) and poly(n-butyl acrylate-co-acrylic acid) (PBAAA) was investigated. No significant effects of the graft copolymer on the domain size were found in the PBA blends. By functionalizing PBA with acrylic acid, the average size of the polyacrylate domains was reduced considerably by the graft copolymer. Thermal and dynamic mechanical analysis of the PS/PBAAA blends revealed that the PBAAA glass transition temperature (T_g) decreased with increasing graft copolymer content. The effect of the graft copolymer in the PS/PBAAA blends can be explained by interactions across the interface due to the formation of hydrogen bonds between the poly(ethylene oxide) (PEO) side chains in the graft copolymer and the acrylic acid segments in the PBAAA phase. Hydrogen bonding was confirmed by IR analysis of binary blends of PEO and PBAAA. Partial miscibility in the PEO/PBAAA blends was indicated by a PEO melting point depression and by a T_g reduction of the PBAAA phase. The thermal properties of the PEO/PBA blends indicated only very limited miscibility. © 1996 John Wiley & Sons, Inc.     

Copolymerization of ethylene and 2-vinylnaphtalene with titanium and zirconium catalysts

Copolymerization of ethylene and 2-vinylnaphtalene (VN) has been investigated with dimethylsilylene(tetramethylcyclopentadienyl)(N-tert-butyl)titanium dichloride (1) and rac-isopropylidenebis(indenyl)zirconium dichloride (2) using methylaluminoxane as a cocatalyst. The copolymerization gave the corresponding copolymer in good yield. The catalyst 1 showed higher incorporation of VN than the catalyst 2. Thermal properties of the resulting copolymers were investigated by DSC in comparison with those of poly(ethylene-co-styrene), and poly(ethylene-co-VN) showed higher T_g than poly(ethylene-co-styrene).     

Studies of crosslinked styrene–alkyl acrylate copolymers for oil absorbency application. I. Synthesis and characterization

The prepolymers for a novel oil absorbent were synthesized by copolymerizing styrene with 2‐ethylhexyl acrylate (EHA), lauryl acrylate (LA), lauryl methacrylate (LMA), and stearyl acrylate (SA). Suspension polymerization was carried out using benzoyl peroxide (BPO) as an initiator with a varying monomer feed ratio, and the copolymers were characterized by FTIR, ¹H‐NMR, DSC, and a solubility test. The copolymers were random copolymers with a single phase, and their compositions were similar to those in the monomer feed. The T_g of the copolymer could be controlled by varying the styrene/acrylate ratio. Acrylates introduced the crosslinking to linear polymers as a side reaction. Crosslinked copolymers were synthesized by adding divinylbenzene (DVB) as a crosslinking agent. At a low degree of crosslinking (0.5 wt % DVB), the T_g of the crosslinked copolymers was lower than or similar to that of the uncrosslinked ones. At a high degree of crosslinking, the T_g increased with increasing crosslinking density. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 903–913, 2000     

Synthesis and characterization of graft copolymers with poly(epichlorohydrin-co-ethylene oxide) as backbone by combination of ring-opening polymerization with living anionic polymerization

Series of graft copolymers with [Poly(epichlorohydrin-co-ethylene oxide)] [Poly(ECH-co-EO)] as backbone and polystyrene (PS), poly(isoprene) (PI) or their block copolymers as side chains were successfully synthesized by combination of ring-opening polymerization (ROP) with living anionic polymerization. The Poly(ECH-co-EO) with high molecular weight (M_n = 3.3 × 10⁴ g/mol) and low polydispersity index (PDI = 1.34) was firstly synthesized by ring-ROP using ethylene glycol potassium as initiator and triisobutylaluminium (i-Bu₃Al) as activator. Subsequently, by “grafting onto” strategy, the graft copolymers Poly(ECH-co-EO)-g-PI, Poly(ECH-co-EO)-g-PS and Poly(ECH-co-EO)-g-(PI-b-PS) were obtained using the coupling reaction between living PI⁻Li⁺, PS⁻Li⁺ or PS-b-PI⁻Li⁺ species capped with or without 1,1-diphenylethylene (DPE) agent and chloromethyl groups on poly(ECH-co-EO). By model experiment, the addition of DPE agent was confirmed to have an important effect on the grafting efficiency at room temperature. Finally, the target graft copolymers and intermediates were characterized by SEC, ¹H NMR, MALLS and FTIR in detail, and thermal behaviours of the graft copolymers were also investigated by DSC measurement.