Studies on the thermal stability and degradation kinetics of Pd/PC nanocomposites

Effect of heating rate, Pd content, and synthesis method on the thermal stability of the ex situ and in situ Palladium/polycarbonate (Pd/PC) nanocomposites was investigated. TEM images revealed discrete Pd nanoclusters of about 5 and 15 nm sizes for 1 and 2 vol % ex situ nanocomposites, respectively. However, agglomerated Pd nanoclusters were noticed in the in situ samples, irrespective of the Pd content. The ex situ Pd/PC nanocomposites showed high onset temperature (Ti) for thermal degradation of PC than the in situ and pure PC samples. Pd content and heating rates were found to have a positive influence on the Ti and Tm (temperature at the maximum degradation rate occurs) of the Pd/PC nanocomposites. Thermal degradation of the PC was found to follow the first‐order kinetics in the Pd/PC nanocomposites. The activation energies associated with the degradation were determined by using the Kissinger method. These activation energies are used to construct the Master decomposition curve (MDC) and weight–time–temperature (α–t–T) plots that describe the time‐temperature dependence of the PC pyrolysis in the Pd/PC nanocomposites. These constructed α–t–T plots were validated with the data from isothermal measurements. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electron spin resonance of VO radical-ion in sub- and supercritical water

Electron spin resonance (ESR) spectra of VO²⁺ radical-ions in sub- and supercritical water are observed. Upon increasing the temperature from 20 to 100 °C, the fine structure line widths in the ESR spectra of the vanadyl ion are observed to be reduced that is associated with the effective averaging of the g-factor anisotropy and the hyperfine interaction. With further increasing the temperature, the spectrum components of the hyperfine structure are broadened significantly resulting in the unresolved low-intensity line in supercritical water with ΔH_pp ∼ 300 G. The data obtained allow behavior peculiarities of the paramagnetic VO²⁺ ions in sub- and supercritical water including rotational dynamics and spin exchange between the radicals to be elucidated. The registration of the unresolved low-intensity line in supercritical conditions points to an increase in the local ion concentration in the system that can be an initial stage for the formation of vanadium-based particles in supercritical conditions. The study demonstrates that ESR is the powerful tool to investigate properties of sub- and supercritical water in situ.     

Behaviour of highly crystalline graphitic materials in lithium-ion cells with propylene carbonate containing electrolytes: An in situ Raman and SEM study

The microcrystalline flaked graphites SFG6 and SFG44 were evaluated with regard to their compatibility with propylene carbonate (PC) by in situ Raman microscopy and postmortem scanning electron microscopy (SEM) study. PC is employed as electrolyte component in lithium-ion batteries. However, when used with certain types of graphitic materials, exfoliation occurs. To compare the effects of exfoliation, the first lithium insertion properties of these graphitic materials were measured with in situ Raman microscopy. Lithium half-cells containing either 1 M LiClO₄ 1:1 (w/w) ethylene carbonate (EC):dimethyl carbonate (DMC) or 1:1 (w/w) EC:PC were investigated. The commencement of the exfoliation process was detected in SFG44 EC:PC by the appearance of a shoulder band at 1597 cm⁻¹ on the G-band (1584 cm⁻¹) below 0.9 V versus Li/Li⁺. The band (assigned as the exfoliation or E-band) at higher wavenumbers (1597 cm⁻¹) corresponded to solvated lithium ions intercalated into graphite. The in situ Raman spectra of SFG6 in EC:DMC or EC:PC and SFG44 in EC:DMC did not show the E-band and instead displayed regular lithium intercalation spectra.In situ Raman microscopy and SEM were further employed to study the exfoliation process observed for SFG44 in 1:1 (w/w) EC:PC, when the potential was held under steady-state conditions at 0.8, 0.6 and 0.3 V, respectively. A blue-shift in the E-band from 1597 to 1607 cm⁻¹ was observed as the potential was lowered. SEM images showed dissimilar degrees of exfoliation at these three potentials.     

Thermostable and flame retardant Mesua ferrea L. seed oil based non-halogenated epoxy resin/clay nanocomposites

Bio-based polymer nanocomposites have a unique niche of their own in the domain of green technology. A bio-based sulfone epoxy resin (BPSE) has been synthesized from the monoglyceride of Mesua ferrea L. seed oil, bis(4-hydroxyphenyl) sulfone, bisphenol-A and epichlorohydrin. The formation of resin was confirmed by the determination of viscosity, epoxy equivalent, etc. and the structure was elucidated from FTIR and ¹H NMR spectroscopies. This resin was used as the matrix for the preparation of epoxy/clay nanocomposites by ex situ technique using different doses of organo nano-clay (1, 2.5 and 5%, w/w). XRD, TEM, SEM, FTIR and rheological studies confirmed the formation of nanocomposites with partial exfoliated structure of the nano-clay. The study demonstrated that the tensile strength enhanced from 4 to 11.4 MPa, scratch hardness improved by two-fold, gloss value increased by 20 units, adhesive strength improved by two-fold and thermal stability improved by 19 °C on incorporation of 5 wt% of nano-clay with respect to the pristine polymer. The limiting oxygen index value and UL94 test indicated improvement of flame retardancy of the nanocomposites. The results exhibit the potentiality of these bio-based epoxy/clay nanocomposites for multifaceted advanced applications.     

Investigation of the surface properties and the hydrogen evolution reaction, HER, at thermal rhodium oxide electrodes

A systematic investigation was conducted of the surface properties and the HER at electrodes of nominal composition Ti/Rh_xTi_(1−x)O_y prepared by thermal decomposition (T_cal: 500 °C; t_cal: 2 h; O₂ flux: 5 dm³ min⁻¹) from salt precursor solutions dissolved in 6.0 mol dm⁻³ HNO₃. Films were characterized ex situ by SEM, EDX, XPS and XRD and in situ by open circuit potential measurements and CV. The electrochemical behaviour was investigated by CV as function of the anodic, E_λ,a, and cathodic, E_λ,c, switching potentials showing the Rh surface oxidation states strongly depend on these experimental variables. Surface Rh-sites are reduced to metallic rhodium in the cathodic potential region while higher oxidation states (I-III) are formed at more positive potentials (E ≥ 0.5 V/RHE). Hydrogen adsorption and desorption peaks as well as a short double layer charging region are observed at intermediate potential values. The HER was investigated by Tafel coefficients and reaction order with respect to H⁺ as function of nominal Rh-content.     

Low temperature synthesis and dielectric, ferroelectric and piezoelectric study of microwave sintered BaTiO3 ceramics

Barium titanate (BaTiO₃/BT) ferroelectric system was synthesized in single perovskite phase at low temperature by using powders derived from modified solid state reaction (MSSR) and sintered by microwave (MW) processing routes. Conventional calcination temperature was optimized at 900 °C for 4 h. MW sintering of BT samples was carried out at 1100 °C for 30 min to get dense (98% density) ceramics. Room temperature (RT) dielectric constant (?_r) and dielectric loss (tan δ) at 1 kHz frequency of MW sintered BT samples was found to be ∼2500 and 0.03, respectively. Saturated polarization vs. electric field (P-E) loops with remnant polarization (P_r) ∼6 μC/cm² and coercive field (E_c) ∼1.45 kV/cm confirmed the ferroelectric nature of MW sintered BT samples. Piezoelectric coefficient from strain vs. electric field (S-E) loops study was found to be 335 pm/V.     

Preparation of electrospun nanofibers of carbon nanotube/polycaprolactone nanocomposite

Multiwalled carbon nanotube/polycaprolactone nanocomposites (MWNT/PCL) were prepared by in situ polymerization, whereby functionalized MWNTs (F-MWNTs) and unfunctionalized MWNTs (P-MWNTs) were used as reinforcing materials. The F-MWNTs were functionalized by Friedel-Crafts acylation, which introduced the aromatic amine (COC₆H₄-NH₂) groups on the side wall. The F-MWNTs were chemically bonded with the PCL chains in the F-MWNT/PCL, as indicated by the appearance of the amide II group in the FT-IR spectrum. The TGA thermograms showed that the F-MWNT/PCL had better thermal stability than PCL and P-MWNT/PCL. The PCL and the nanocomposite nanofibers were prepared by an electrospinning technique. The nanocomposites that contain more than 2 wt% of MWNTs were not able to be electrospun. The bead of the F-MWNT/PCL nanofiber was formed less than that of the P-MWNT/PCL. The nanocomposite nanofibers showed a relatively broader diameter than the pure PCL nanofibers. The MWNTs were embedded within the nanofibers and were well oriented along the axes of the electrospun nanofibers, as confirmed by transmission electron microscopy.     

High performance electrode for electrochemical oxygen generator cell based on solid electrolyte ion transport membrane

A double-layer composite electrode based on Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ + Sm_0.2Ce_0.8O_1.9 (BSCF + SDC) and BSCF + SDC + Ag was investigated to be a promising cathode and also anode for the electrochemical oxygen generator based on samaria doped ceria electrolyte. The Ag particles in the second layer were not only the current collector but also the improver for the oxygen adsorption at the electrode. a.c. impedance results indicated that the electrode polarization resistance, as low as 0.0058 Ω cm² was reached at 800 °C under air. In oxygen generator cell performance test, the electrode resistance dropped to half of the value at zero current density under an applied current density of 2.34 A cm⁻² at 700 °C, and on the same conditions the oxygen generator cell was continual working for more than 900 min with a Faradic efficiency of ∼100%.     

Microstructure and physicomechanical properties of pressureless sintered multiwalled carbon nanotube/alumina nanocomposites

Multiwalled carbon nanotube (MWCNT)/alumina (Al₂O₃) nanocomposites containing CNT from 0.15 vol.% to 2.4 vol.% have been successfully fabricated by simple wet mixing of as-received commercial precursors followed by pressureless sintering. Extent of densification of nanocomposites sintered at low temperature (e.g. 1500 °C) was <90%, but increased up to ∼99% when sintered at 1700 °C and offered superior performance compared to pure Al₂O₃. Nanocomposites containing 0.3 vol.% MWCNT and sintered at 1700 °C for 2 h in Argon led to ∼23% and ∼34% improvement in hardness and fracture toughness, respectively, than monolithic Al₂O₃. In addition, the highest improvement (∼20%) in bending strength was obtained for 0.15 vol.% MWCNT/Al₂O₃ nanocomposite compared to pure Al₂O₃. Weibull analysis indicated reliability of nanocomposites increased up to 0.3 vol.% MWCNT, whereas, beyond that loading consistency was the same as obtained for pure Al₂O₃. Detailed microstructure and fractographic analysis were performed to assess structure-property relationship of present nanocomposites.     

Temperature dependence of surface composition and morphology in polymer blend film

Thin films of poly(methyl methacrylate) (PMMA) and poly(styrene-ran-acrylonitrile) (SAN) blend can phase separate upon heating to above its critical temperature. Temperature dependence of the surface composition and morphology in the blend thin film upon thermal treatment was studied using in situ X-ray photoelectron spectroscopy (XPS) and in situ atomic force microscopy (AFM). It was found that in addition to phase separation, the blend component preferentially diffused to and aggregated at the surface of the blend film, leading to the variation of surface composition with temperature. At 185 °C, above the critical temperature, the amounts of PMMA and SAN phases were comparable. At lower temperatures PMMA migrated to the surface, leading to a much higher PMMA surface content than in the bulk. The migration and preferential segregation of a blend component in thin films demonstrated here are responsible for the great difference between in situ and ex situ experimental (not real quenching or annealing) results of polymer blend films, and help explain the slow kinetics of surface phase separation at early stage for blend thin films reported in literature. This is significant for the control of surface properties of polymer materials.     

Preparation and properties of biodegradable PBS/multi-walled carbon nanotube nanocomposites

In this study, poly(butylene succinate)/multi-walled carbon nanotube (PBS/MWNT) hybrids were prepared by a melt-blending process. The carbon nanotubes (CNTs) were successfully modified using N,N′-dicyclohexylcarbodiimide (DCC) dehydrating agents. As a result, excellent dispersion of the modified carbon nanotubes (CNT-C18) in organic solvents was achieved. Subsequently, the PBS/CNT nanocomposites were prepared through facile melt blending. Mechanical properties, thermal behavior, conductivity of these resultant polymer/CNT composites were investigated. The results obtained show that the PBS/CNT-C18 nanocomposites consisting of well-dispersed nanotubes exhibited enhanced thermal and mechanical properties. With the addition of 3 wt% CNT-C18, T_d of the nanocomposite increased 12.3 °C as compared to that of the pristine PBS sample. Moreover, the increments of E′ and E″ of the nanocomposite at 25 °C were 120 and 55%, respectively. In the aspect of conductivity, the surface resistivity of the PBS/CNT-C18 composite was found to be 7.30 × 10⁶ Ω, which is a decrease of 10⁹ fold in value as compared to that of the pristine PBS sample. Such PBS/CNT-C18 sample exhibits high anti-static efficiency, which would be potentially useful in electronic packaging materials.     

A novel nanocomposite of Pd nanocluster/poly(N-acetylaniline) nanorod modified electrode for the electrocatalytic reduction of oxygen

A novel nanocomposite of palladium nanoclusters/poly(N-acetylaniline) nanorods was electrodeposited on to a glassy carbon electrode by cyclic voltammetry (CV). This electrode, Pd/PAANI/GCE, was characterized by X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), CV and chromoamperometry. It was demonstrated that the ball-shaped Pd nanoclusters were mainly growing on the ends of the nanorods, forming a novel nanocomposite. The preliminary study also demonstrated that the electrode modified with this nanocomposite matrix had high electrocatalytic activity toward 4-e⁻ oxygen reduction.     

PMMA-mesocellular foam silica nanocomposites prepared through batch emulsion polymerization and compression molding

PMMA-mesoporous silica nanocomposites were prepared for the first time through in situ batch emulsion polymerization of methyl methacrylate in the presence of large pore MSU-F silica with a mesocellular foam structure (24.8 nm average cavity size) and subsequent compression molding of the polymer-silica nanoparticle mixtures. For composites containing 5.0 wt % silica, the onset decomposition temperature and the temperature at 10% weight loss for the nanocomposite increased 41 °C and 50 °C, respectively, in comparison to pure PMMA. The glass transition temperature of the nanocomposite increased 9.3 °C, as determined by differential scanning calorimetry. In addition, the storage modulus determined by dynamic mechanical analysis increased 17% and 80% at 50 °C and 100 °C, respectively. Substantial improvements in tensile strength (+50%) and modulus (+72%), were achieve at 10 wt % nanoparticle loading. Composites made by compression molding of physical mixtures of PMMA and MSU-F silica powders provide less improvement in thermal stability, glass transition temperature and mechanical properties in comparison to the composites made through in situ batch emulsion polymerization. Unlike previously reported composites made from nanoclays, the silica composites reported here show improvements in both thermal stability and mechanical reinforcement.     

High ionic transfer of a hyperbranched-network gel copolymer electrolyte for potential electric vehicle (EV) application

Hyperbranched network-based gel copolymer electrolytes are synthesized by in situ free radical polymerization. This research is separated into two parts: the first is an investigation of modified bismaleimide oligomer (MBMI) as a free volume additive, and the second investigates the salt concentration effect on high power application. A polymer electrolyte with MBMI additive provided more free volume space, and the ionic conductivity of gel copolymer electrolytes was measured as a function of the salt concentration of lithium hexafluorophosphate (LiPF₆). The highest ionic conductivity and the lowest activation energy of hyperbranched-network gel copolymer electrolytes were determined to be 7.72 × 10⁻³ S/cm at 23 °C and 5.41 kJ/mol, respectively. Furthermore, the MBMI additive and the optimal concentration of lithium salt increased the free space for carrier ions and contributed to increasing capacity and working voltage at a high rate discharge (8C). The reliability and cycling ability of lithium polymer batteries are as good as lithium ion batteries for potential electric vehicle (EV) application.     

NiP^O and [Cp2ZrCl2/MAO] as a versatile dual-function catalyst system for in situ polymerization of ethylene to linear low-density polyethylene (LLDPE)

[Ni(Ph₂PCHCOPh)(Ph)(PPh₃)] (NiP^O) and Cp₂ZrCl₂/methylaluminoxane (MAO), well known as ethylene oligomerization and polymerization catalysts, respectively, are combined to produce LLDPE by in situ polymerization. Melting temperature (T_m), degree of crystallinity (χ_c), intrinsic viscosity, average molecular weight and ¹³C NMR analysis of copolymers confirm the insertion of α-olefins into the polyethylene chain. Variations in α-olefin concentration and ethylene pressure during the polymerization stage lead to changes in the degree of branching. The resulting copolymers have χ_c and T_m in the 25.8–65.2% and 114–132 °C ranges, respectively. Experimental results show the versatility of the dual-function catalyst.     

Preparation and characterization of reticular SSC cathode films by electrostatic spray deposition

Sm_0.5Sr_0.5CoO_3−δ (SSC) cathode films were deposited on CGO (Gd_0.1Ce_0.9O_1.95) electrolyte substrates by electrostatic spray deposition to prepare SSC/CGO/SSC symmetrical cells. Deposition parameters were changed systematically to examine their effects on film microstructure and electrode performance. A set of deposition parameters including a 0.01 M precursor solution containing metal nitrates in a mixture solvent of de-ionized water (0.6 vol%), ethanol (1.5 vol%) and diethyl butyl carbitol (97.9 vol%), a flow rate of 6 ml/h for precursor solution, a deposition temperature of 350 °C and an imposed electric field of 10 kV/3 cm was identified for preparation of films with a highly porous reticular structure. The superior performance of a reticular SSC electrode was evidenced by its low interfacial resistances of 0.275 and 0.018 Ω cm² measured in 500 and 700 °C, respectively. These values were one-half to one order of magnitude smaller than that of the screen-printed or slurry-painted electrodes.     

Changes on iron electrode surface during hydrogen permeation in borate buffer solution

Hydrogen interaction with oxide films grown on iron electrodes at open circuit potential (E_oc) and in the passive region (+0.30 V_ECS) was studied by chronopotentiometry, chronoamperometry and electrochemical impedance spectroscopy techniques. The results were obtained in deaerated 0.3 mol L⁻¹ H₃BO₃ + 0.075 mol L⁻¹ Na₂B₄O₇ (BB, pH 8.4) solution before, during and after hydrogen permeation. The iron oxide film modification was also investigated by means of in situ X-ray absorption near-edge spectroscopy (XANES) and scanning electrochemical microscopy (SECM) before and during hydrogen permeation. The main conclusion was that the passive film is reduced during the hydrogen diffusion. The hydrogen permeation stabilizes the iron surface at a potential close to the thermodynamic water stability line where hydrogen evolution can occur. The stationary condition required for the determination of the permeation parameters cannot be easily attained on iron surface during hydrogen permeation. Moreover, additional attention must be paid when obtaining the transport parameters using the classical permeation cell.     

Role of interface on electrical conductivity of carbon nanotube/alumina nanocomposite

Interface of multiwalled carbon nanotube (MWCNT)/alumina (Al₂O₃) nanocomposites have been studied using TEM. At low sintering temperature (T_sin=1500 °C), a 3–5 nm thick amorphous interface region was noticed. Nanocomposite sintered at 1700 °C possessed a well-defined graphene layer coating on matrix grains as the interface between CNT and Al₂O₃. A mechanism of such layered interface formation has been proposed. No traceable chemical reaction product was observed at the interface even after sintering at 1700 °C. It was noticed that while DC electrical conductivity (σ_DC) of 1500 °C sintered 2.4 vol% MWCNT/Al₂O₃ nanocomposite was only~0.02 S/m, it raised to ~21 S/m when sintering was done at 1700 °C. Such 10³ times increase in σ_DC of present nanocomposite at a constant CNT loading was not only resulted from the exceptionally high electron mobility of CNT but the well-crystallized graphene interface on insulating type Al₂O₃ grains also significantly contributed in the overall increase of electrical performance of the nanocomposite, especially, when sintering was done at 1700 °C.     

Effect of hydrogen bonding on the rheology of polycarbonate/organoclay nanocomposites

The linear dynamic viscoelastic properties and non-linear transient rheology of polycarbonate (PC)/clay nanocomposites were investigated at temperatures ranging from 240 to 280 °C. For the study, nanocomposites of PC and natural montmorillonite (Cloisite Na⁺) or chemically modified clay (Cloisite 30B) were prepared by melt blending in a twin-screw extruder. Cloisite 30B is a natural montmorillonite modified with methyl, tallow, bis-2-hydroxyethyl, quaternary ammonium chloride (MT2EtOH). In both PC/Cloisite Na⁺ and PC/Cloisite 30B nanocomposites the concentration of clay was varied from 2.3 to 4.3 wt%. In situ Fourier transform infrared (FTIR) spectroscopy results show that at temperatures ranging from 30 to 280 °C the carbonyl groups in PC and the hydroxyl groups in MT2EtOH of Cloisite 30B in PC/Cloisite 30B nanocomposites formed hydrogen bonds, while no evidence of hydrogen bonding was observed in the PC/Cloisite Na⁺ nanocomposites. There are no discernible sharp reflections in the X-ray diffraction (XRD) patterns of PC/Cloisite 30B nanocomposites, after Cloisite 30B having the d₀₀₁ spacing of 1.85 nm was mixed with PC, whereas the d₀₀₁ spacing changes little (1.17 nm) before and after the mixing of Cloisite Na⁺ to PC. Transmission electron microcopy (TEM) images show that organoclay platelets are well dispersed in PC/Cloisite 30B nanocomposites, while the untreated clay platelets are poorly dispersed in PC/Cloisite Na⁺ nanocomposites. The observed differences in XRD patterns and TEM images between the two nanocomposite systems are explained by in situ FTIR spectroscopy. The results of rheological measurements (linear dynamic viscoelasticity, non-linear transient shear flow, and steady-state shear flow) support the conclusions drawn from the results of XRD, TEM, and FTIR spectroscopy.     

In situ generation of diazonium cations in organic electrolyte for electrochemical modification of electrode surface

The modification of glassy carbon electrode was achieved by electrochemical reduction of in situ generated diazonium cations in acetonitrile. The in situ generation of 4-nitrophenyl diazonium cations in acetonitrile was investigated by spectroscopic methods. UV-visible spectroscopy revealed slow kinetics for the reaction of 4-nitroaniline with tert-butylnitrite in acetonitrile to form the corresponding diazonium cation. As a result, a coupling reaction, which implies a consumption of the amine and loss of the already formed diazonium cations, was evidenced by ¹H NMR spectroscopy. This spectroscopic study allowed the optimization of the in situ diazonium cations generation prior to the modification step. The electrochemical modification of the carbon electrodes with 4-nitrophenyl, 4-bromophenyl and anthraquinone groups was characterized by cyclic voltammetry and the resulting grafted layer were characterized by electrochemical techniques. The cyclic voltammetric behaviour during the electrochemical grafting was very similar to the one observed for an isolated diazonium salt dissolved in acetonitrile. In the case of the anthraquinone-modified electrode, the use of acetonitrile, into which the corresponding amine is soluble but not in aqueous media, allowed for its grafting by the in situ approach. The barrier properties of these grafted layers are similar to those obtained from isolated diazonium salts. Finally, the chemical composition of the grafted layers was determined by X-ray photoelectron spectroscopy and surface coverage in the range 5-7 × 10⁻¹⁰ mol cm⁻² was estimated for films grown in our experimental conditions.