Miscibility of poly(styrene-co-vinyl phenol) with poly(ɛ-caprolactone)

Summary Poly(styrene-co-vinyl phenol) (STVPh)/poly(-caprolactone)(PCL) blends showed enhanced miscibility over polystyrene/PCL blend, and showed single glass transition temperature when the contents of vinyl phenol (VPh) in copolymer were higher than 10 wt % (maximum content of VPh in STVPh used in this study was 20 wt%). STVPh 4, STVPh 7, STVPh 10 (4, 7, 10 were VPh wt%)/PCL blends showed cloud points on heating for miscible blend system, and this phase separation was reversible on cooling. From melting point depression of PCL, interaction parameter, B. for miscible STVPh 12/PCL blend system was evaluated.     

Rheological properties of poly(ε-caprolactone) and poly(styrene-co-acrylonitrile) blends

Summary Rheological properties of poly(-caprolactone) (PCL) and Poly (styrene-co-acrylonitrile) (SAN) blends were examined as a function of the acrylonitrile (AN) content in SAN, to systematically understand the correlation between the interaction parameter and the theological properties of miscible polymer blends. When the plateau modulus (G _N ⁰) and zero shear viscosity ( ₀) of the PCL/SAN blends are plotted against the AN content in SAN, a minimum is observed. Qualitatively, the results obtained parallel the variation of the interchain interaction with the AN content. The negative deviation ofG _N ⁰ and ₀ from linearity seems to be attributed to the increase in the entanglement molecular weight between dissimilar chains which results from the chain extension caused by interchain interaction.     

Nanosized micelles self-assembled from amphiphilic poly(citric acid)–poly(ε-caprolactone)–poly(citric acid) copolymers

In this study, novel ABA-type amphiphilic copolymers consisting of poly(citric acid) (PCA) (A) as hydrophilic segment and poly(ε-caprolactone) (PCL) (B) as hydrophobic block were prepared by an approach in the following two steps: (1) ring-opening polymerization (ROP) of ε-caprolactone with 1,5-pentanediol initiator to obtain a hydroxyl telechelic PCL; (2) melt polycondensation reaction of hydroxyl telechelic PCL and citric acid molecules. The prepared copolymers are capable of self-assembling into nanosized micelles in aqueous solution. The influence of the copolymer composition on the micelle dimensions was investigated. The critical micellar concentration of the copolymers is in the range of 5–6.3 × 10^?2 mg/mL which is determined by the fluorescence probe technique using pyrene. Also the results indicate that CMC of self assembled micelles is influenced by the hydrophilicity of PCA–PCL–PCA copolymers depending on the CA/CP ratio, and these micelles may find great potential as drug carriers in biomedical fields.     

Crystallization and morphology of poly(ethylene succinate) and poly(β-hydroxybutyrate) blends

Summary The melting and crystallization behavior of poly(β-hydroxybutyrate) (PHB) and poly(ethylene succinate) blends has been studied by differential scanning calorimetry and optical microscopy. The results indicate that PHB and PES are miscible in the melt. Consequently the blend exhibits a depression of the melting temperature of both PHB and PES. In addition, a depression of the equilibrium melting temperature of PHB is observed. The Flory-Huggins interaction parameter (χ₁₂ ), obtained from melting point depression data, is composition dependent, and its value is always negative. Isothermal crystallization in the miscible blend system PES/PHB is examined by polarized optical microscope. The presence of the PES component gives a wide variety of morphologies. The spherulites exhibit a banded structure and the band spacing decreases with increase PES content. Received: 29 June 1998/Revised version: 31 August 1998/Accepted: 10 September 1998     

DSC studies of poly(vinyl chloride)/poly(ε-caprolactone)/poly(ε-caprolactone)-b-poly(dimethylsiloxane) blends

Poly(vinyl chloride)/poly(ε-caprolactone)/poly(ε-caprolactone)-b-poly(dimethylsiloxane) [PVC/PCL/(PCL-b-PDMS)] blends were prepared by solvent casting from tetrahydrofuran. The content of PVC was kept constant (60 wt%); the PCL and PCL-b-PDMS contents were varied by replacing different amounts of PCL [0–20 wt% from the PVC/PCL (60/40) blend] with PCL-b-PDMS copolymer having different molecular weights of the PCL blocks. The thermal properties of prepared blends were investigated by differential scanning calorimetry in order to analyse miscibility (through glass transition temperature) and crystallinity. Differential scanning calorimetry analyses show that the PVC/PCL/PCL-b-PDMS blends are multi-phase materials which contain a PVC plasticized with PCL phase, a block copolymer PCL-b-PDMS phase (with crystalline and amorphous PCL and PDMS domains) and a PCL phase (preponderantly crystalline).     

Single-component poly(ε-caprolactone) composites

Non-covalently bonded crystalline inclusion compounds (ICs) have been formed by threading host cyclic starches, α-cyclodextrins (α-CDs), onto guest poly(ε-caprolactone) (PCL) chains and by co-crystallization of guest PCL and host urea (U). PCLs were coalesced from both ICs by appropriate removal of the α-CD and U hosts. When added at low concentrations, PCL coalesced from its α-CD–IC served as an effective self-nucleating agent for the bulk crystallization of as-received PCL from the melt. Film sandwiches consisting of two layers of as-received (asr) (control), and one layer each of asr and self-nucleated (nuc) (composite) PCLs were produced by melt pressing. A composite sandwich consisting of a film of neat PCL coalesced from its U–IC (c-PCL) and a film of asr-PCL was also melt pressed. DSC showed that both composite films maintain their characteristic structures and properties even after melt-pressing them together. Both single component film sandwiches exhibited strong interfaces and better mechanical properties than the asr-PCL/asr-PCL control composite sandwiches. These results are similar to those previously obtained on similarly prepared nylon-6 (N-6) sandwich composites made with asr- and nuc-N-6 films with the same levels of crystallinity. However, while the elongation at break was greatly reduced in the asr-N-6/nuc-N-6 composite, asr-/asr-, asr-/c-, and asr-/nuc-, PCL/PCL-composites all showed similarly large elongations at break. The above room temperature and well below room temperature glass-transition temperatures of N-6 and PCL are likely the cause of their widely different elongations at break.     

Mechanism of thermal generation of poly(p-phenylene vinylene) from poly(p-xylene-α-dimethylsulphonium halides)

The thermal conversion of poly(p-xylene-α-dimethylsulphonium halides) into poly(p-phenylene vinylene) (PPV) can occur through two concomitant reactions. The principal reaction is an elimination of dimethyl sulphide and halogen acid, while the second reaction, an undesirable one, is the nucleophilic attack of the halide counterion on a methyl group to form the methyl halide and a methyl sulphide. The two thermal processes were observed in the pyrolysis of both poly(p-xylene-α-dimethylsulphonium bromide) and poly(p-xylene-α-dimethylsulphonium chloride). On storage at room temperature, poly(p-xylene-α-dimethylsulphonium halides) undergo partial decomposition to PPV, as shown by thermogravimetric experiments. The flash pyrolysis-gas chromatography-mass spectrometry of PPV obtained by the thermal conversion of poly(p-xylene-α-dimethylsulphonium bromide) at 400°C was also investigated.     

Miscibility behaviour of sulfonylated poly(2,6-dimethyl-1,4-phenylene oxide) copolymers in the blends with poly(styrene-co-maleic anhydride) and with poly(α-methylstyrene-co-maleic anhydride)

Summary The miscibility behaviour of sulfonylated poly(2,6-dimethyl-1,4-phenylene oxide) of the different degree of sulfonylation blended with poly(styrene-co-maleic anhydride) or poly(-methylstyrene-co-maleic anhydride) was studied. The critical degree of sulfonylation for phase separation in these blends was found to be 55 mole % and 66 mole %, respectively. The miscibility behaviour was analyzed on the basis of the mean field treatment and studied by DSC.Dedicated to Professor Dragutin Fle in honor of his 70th birthday     

Thermal properties of di- and triblock copolymers of poly(l-lactide) with poly(oxyethylene) or poly(ε-caprolactone)

High molecular weight di- and triblock copolymers of poly(l-lactide), PLLA, (80 wt%) with a crystallizable flexible second component such as poly(ε-caprolactone), PCL, or poly(oxyethylene), PEO, (20 wt%) were obtained in nearly quantitative yields by ring opening of l-lactide initiated by PCL or PEO hydroxy terminated macromers. The copolymers were characterized by ¹H NMR and FTIR spectroscopy and size exclusion chromatography and showed unimodal and narrow molecular weight distributions. X-ray diffraction measurements revealed high crystallinity (38-56%) of the PLLA blocks and gave no clear evidences of PCL or PEO crystallinity. DMTA and DSC techniques showed a melting behaviour of the copolymers (T_m=174-175 °C; ΔH_m=19-37 J/g) quite similar to that of PLLA. PCL and PLLA segments are immiscible, while PLLA and PEO segments are partially miscible in the amorphous phase. Stress-strain measurements indicated a ductile behaviour of the copolymers, characterized by lower tensile moduli (225-961 Pa) and higher elongations at break (25-134%) with respect to PLLA.     

Modeling of interdiffusion in poly(vinyl acetate)–poly(methyl methacrylate)–toluene multicomponent systems

Work on interdiffusion has been mainly carried out in binary systems in the past, and this work has focused on polymer–solvent (S) systems and polymer blends. To understand and predict the interdiffusion of two solids in the presence of one S, we present a new mathematical model based on the Onsager approach. Within our model, interdiffusion kinetics are described with a modification of the reptation model for long polymer chains, and the chemical potential gradient is used as the driving force behind mass transfer. The chemical potential is calculated with a Flory–Huggins approach. The model was validated with 29 Raman spectroscopy experiments in poly(vinyl acetate)–poly(methyl methacrylate)–toluene systems at 20 °C. Monomer mobilities (L _i,0s) were determined for both polymers to show the independence of L _i,0 from the chain length. The L _i,0s were found to be strongly dependent on the S content. With the knowledge of phase equilibria and L _i,0s, interdiffusion in the ternary polymer–polymer–S system could be predicted by the introduced model. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47092.     

Prevention of poly(vinyl chloride) degradation through organic terephthalamides generated from poly(ethylene terephthalate) waste

The use of organic compounds as thermal stabilizers for poly(vinyl chloride) (PVC) stabilization is the current state of art worldwide owing to their high efficiency and nontoxic residues after degradation. Terephthalamide, N,N′-dimethylterephthalamide and N,N′-dibutylterephthalamide have been prepared via depolymerization of poly(ethylene terephthalate) through an economical and environmentally friendly approach. These compounds have been examined as thermal stabilizers for PVC formulations and found to exhibit high thermal stabilizing effects. Thermal stability measurements were performed using conventional Congo red test method. Color change experiments were conducted by heating the samples at 200 °C in air, and the colored compounds formed were extracted and compared with the help of UV–visible spectroscopy. Fourier transform infrared spectroscopic studies of organic terephthalamides incorporated PVC samples have been performed in order to insight the probable mechanistic aspects involved in thermal stabilization process. Thermogravimetric analysis (TGA) thermograms of PVC sheets loaded with 10 wt % organic terephthalamides have been recorded and were found stable below 200 °C. SEM and energy dispersive X-ray analysis of char residues of TGA samples were performed supporting the proposed thermal stabilizing action of the organic terephthalamides. Furthermore, specific gravity and mechanical performance of the PVC sheets have also been reported assisting in finding suitable commercial applications of PVC formulations. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48022.     

Molecular weight effect on theta-gel formation in poly(vinyl alcohol)–poly(ethylene glycol) mixtures

Injectable hydrogel formulations that undergo in situ gelation at body temperature are promising for minimally invasive tissue repair. This work focuses on the investigation of injectable poly(vinyl alcohol) (PVA) and poly(ethylene glycol) (PEG) mixtures. The injectable PVA–PEG aqueous solutions form a hydrogel as temperature is reduced to near body temperature, while filling a defect in the injection site. Gamma sterilization of these solutions compromises injectability presumably due to crosslinking of PVA. We hypothesized that by modifying the PEG molecular weight and its concentration, injectability of radiation sterilized PVA–PEG hydrogels can be optimized without compromising the mechanical properties of the resulting gel. The use of a bimodal mixture of higher and lower molecular weight PEG (600 and 200 g/mol) resulted in lower PVA/PEG solution viscosity, better injectability, and higher gel mechanical strength. The PVA/bimodal-PEG had a lower viscosity at 2733 ± 149 cP versus a viscosity of 5560 ± 278 cP for PVA/unimodal-PEG (400 g/mol). The gel formed with the bimodal PEG mixture had higher creep resistance (61% total creep strain under 0.5 MPa) than that formed with unimodal PEG (84%). These hydrogel formulations are promising candidates for minimally invasive tissue repair. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of a novel amphiphilic poly (ethylene glycol)–poly (ε-caprolactone) graft copolymers

A series of amphiphilic graft copolymers PEO-g-PCL with different poly (ε-caprolactone) (PCL) molecular weight were successfully synthesized by a combination of anionic ring-opening polymerization (AROP) and coordination-insertion ring-opening polymerization. The linear PEO was produced by AROP of ethylene oxide (EO) and ethoxyethyl glycidyl ether initiated by 2-(2-methoxyethoxy) ethoxide potassium, and the hydroxyl groups on the backbone were deprotected after hydrolysis. The ring-opening polymerization of CL was initiated using the linear poly (ethylene oxide) (PEO) with hydroxyl group on repeated monomer as macroinitiator and Sn(Oct)₂ as catalyst, then amphiphilic graft copolymers PEO-g-PCL were obtained. By changing the ratio of monomer and macroinitiator, a series of PEO-g-PCL with well-defined structure, molecular weight control, and narrow molecular weight distribution were prepared. The expected intermediates and final products were confirmed by ¹H NMR and GPC analyzes. In addition, these amphiphilic graft copolymers could form spherical aggregates in aqueous solution by self-assemble, which were characterized by transmission electron microscopy, and the critical micelle concentration values of graft copolymers PEO-g-PCL were also examined in this article.     

Effects of storage on thermomechanical properties of poly(ɛ-caprolactone) blends containing poly(vinyl pyrrolidone/iodine)

Abstract

This study reports the effects of: the molecular weight ratio of poly(?-caprolactone) (PCL) in blends containing polymer of high (50 000 g mol^-1 ) and low (4000 g mol^-1 ) molecular weight; the concentration (0, 1, and 5 wt-%) of poly(vinyl pyrrolidone/iodine) (PVP/I); and storage at 30°C and 75% relative humidity; on the thermomechanical properties of films prepared by solvent evaporation from solutions containing both PCL and PVP/I. The tensile properties were found to be statistically dependent on the molecular weight ratio of PCL but not on the concentration of PVP/I. The reductions in tensile strength and elongation at break associated with increasing amounts of low molecular weight PCL were attributed to a reduction in the concentration of chain entanglements. No changes were observed in viscoelastic properties or the glass transition temperature. Following storage there were no changes in the tensile strength, glass transition temperature, or viscoelastic properties of the films; however, significant reductions in elongation at break were observed. It is suggested that this is due to hydrolytic chain scission of amorphous PCL. Inclusion of 5 wt-% PVP/I increased this process in films containing 100 : 0 and 80 : 20 high/low molecular weight PCL (but not 60 : 40), but the extent of this was small. This study highlighted significant aging properties of PCL in a moist atmosphere. Consequently, it is recommended that suitable packaging materials should be employed to control the exposure of PCL films to water during storage.     

Effect of poly(ε-caprolactone) and titanium (IV) dioxide content on the UV and hydrolytic degradation of poly(lactic acid)/poly(ε-caprolactone) blends

The effect of accelerated weathering degradation on the properties of poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blends and PLA/PCL/titanium (IV) dioxide (TiO₂) nanocomposites are presented in this paper. The results show that both polymers are susceptible to weathering degradation, but their degradation rates are different and are also influenced by the presence of TiO₂ in the samples. Visual, microscopic and atomic force microsocpy observations of the surface after accelerated weathering tests confirmed that degradation occurred faster in the PLA/PCL blends than in the PLA/PCL/TiO₂ nanocomposites. The X-ray diffraction results showed the degradation of PCL in the disappearance of its characteristic peaks over weathering time, and also confirmed that PLA lost its amorphous character and developed crystals from the shorter chains formed as a result of degradative chain scission. It was further observed that the presence of TiO₂ retarded the degradation of both PLA and PCL. These results were supported by the differential scanning calorimetry results. The thermogravimetric analysis results confirmed that that PLA and PCL respectively influenced each other's thermal degradation, and that TiO₂ played a role in the thermal degradation of both PLA and PCL. The tensile properties of both PLA/PCL and PLA/PCL/TiO₂ were significantly reduced through weathering exposure and the incorporation of TiO₂.     

In vitro degradation of poly(l-lactide)/poly(ε-caprolactone) blend reinforced with MWCNTs

The physical and mechanical properties of poly(l-lactide)/poly(??-caprolactone) (PLLA/PCL) blends reinforced with multiwalled carbon nanotubes (MWCNTs) before and after in vitro degradation were investigated. Because of brittleness, PLLA needs to be plasticized by PCL as a soft polymer. The MWCNTs are used to balance the stiffness and the flexibility of PLLA/PCL blends. The results showed that with incremental increase in concentration of MWCNTs in composites, the agglomerate points of MWCNTs were increased. The physical and mechanical properties of prepared PLLA/PCL blends and MWCNT/PLLA/PCL nanocomposites were characterized. The X-ray diffraction analysis of the prepared blends and composites showed that MWCNTs, as heterogeneous nucleation points, increased the lamella size and therefore the crystallinity of PLLA/PCL. The mechanical strength of blends was decreased with incremental increase in PCL weight ratio. The mechanical behavior of composites showed large strain after yielding and high elastic strain characteristics. The tensile tests results showed that the tensile modulus and tensile strength are significantly increased with increasing the concentration of MWCNTs in composites, while, the elongation-at-break was decreased. The in vitro degradation rate of polymer blends in phosphate buffer solution (PBS) increased with higher weight ratio of PCL in the blend. The in vitro degradation rate of nanocomposites in PBS increased about 65% when the concentration of MWCNTs increased up to 3% (by weight). The results showed that the degradation kinetics of nanocomposites for scaffolds can be engineered by varying the contents of MWCNTs.     

Thermal decomposition of some poly(β-hydroxyalkanoates)

The thermal decomposition of some polyhydroxyalkanoates (PHA) has been investigated by means of thermogravimetry and differential thermogravimetry. The thermal stability of the studied polyesters decreases slightly with increasing hydroxyvalerate (HV) comonomer. This result is different from those reported in the literature. Other results agree with reaction mechanisms proposed in the literature. The data from dynamic thermogravimetric experiments are consistent with a first order reaction, as would be expected from the reaction mechanism. Infrared spectra of the thermally degraded and undegraded copolymers are evidence of the cis-elimination mechanism. © 1999 Society of Chemical Industry     

Compatibilisation of blends of poly(vinyl chloride) and poly(styrene-block-(ethylene-co-butadiene)-block–styrene) with maleic anhydride grafting

Abstract

The mechanical properties of blends of poly (vinyl chloride) (PVC) and poly (styrene-block-(ethylene-co-butadiene)-block–styrene) (SEBS) were investigated using maleic anhydride grafted SEBS (SEBS-g-MAH) as a compatibiliser. The results indicated that addition of a small amount of SEBS-g-MAH during melt blending significantly improved the mechanical properties of PVC/SEBS blends. The impact strength of the compatibilised PVC/SEBS blends was found to reach a maximum of 53·5±2·78 KJ m^?2 at room temperature and a maximum of 32·8±1·66 KJ m^?2 at ?20°C at an SEBS-g-MAH loading level of 6 phr. The two glass transition temperatures of the components in the blends converged to some degree upon addition of SEBS-g-MAH for compatibilisation. At room temperature the dynamic storage modulus of the compatibilised blends was higher than that of the blends without compatibilisation. The size of the dispersed phase domains in the blends was appreciably reduced on addition of SEBS-g-MAH during melt blending according to scanning electron microscopy. All the above observations revealed that SEBS-g-MAH enhanced the compatibility between PVC and SEBS in the PVC/SEBS blends.     

Synthesis and characterization of polyrotaxanes comprising α-cyclodextrins and poly(ε-caprolactone) end-capped with poly(N-isopropylacrylamide)s

Biodegradable polyrotaxane (PR)-based triblock copolymers were synthesized via the atom transfer radical polymerization (ATRP) of N-isopropylacrylamide (NIPAAm) initiated with polypseudorotaxanes (PPRs) consisting of a distal 2-bromopropiomyl bromide end-capping poly(ε-caprolactone) (Br-PCL-Br) and a varying amount of α-cyclodextrins (α-CDs) in the presence of Cu(I)Br/PMDETA at 25 °C in aqueous solution. The copolymers were featured by relatively higher yields from 46.0% to 82.8% as compared with previous reports. Their structure was characterized in detail by using ¹H NMR, ¹³C CP/MAS NMR, GPC, WXRD, DSC and TGA analyses. When a feed molar ratio of NIPAAm to Br-PCL-Br was changed from 50 to 200, the degree of polymerization of PNIPAAm blocks attached to two ends of PPRs was in a range of 158–500. About one third of the added α-CDs were still entrapped on the central PCL chain after the ATRP process. Attaching PNIPAAm rendered the copolymers soluble in aqueous solution showing the thermo-responsibility as evidenced by turbidity measurements.     

Oxidative degradation of poly (vinyl acetate) and poly (ε-caprolactone) and their mixtures in solution

The oxidative degradation of the poly (ε-caprolactone) (PCL), poly (vinyl acetate) (PVAC) and their mixtures in dichlorobenzene has been investigated at various temperatures (70-130°C) in the presence of benzoyl peroxide. The interaction between the polymers is quantified by monitoring the molecular weights of individual polymers using gel-permeation chromatography. The various physical mixtures employed in the present investigation are , and wt%/wt% PCL/PVAC. Experimental data indicated that the degradation is random without cross-linking and repolymerization. An optimum in degradation temperature (corresponding to maximum degradation rate) of 105°C was observed for the entire range of polymer compositions (0-100% PCL) investigated. This optimum temperature of degradation is characteristic mostly of the initiator and only to a small extent of the degrading polymer system. The experimental results of the mixtures indicated that the degradation rates of PVAC are significantly enhanced, while the degradation rates of PCL are decreased in the physical mixture. This can be attributed to the proton-accepting and proton-donating nature of PCL and PVAC, respectively. A radical mechanism for the oxidative degradation of pure polymers and their mixtures has been proposed and a model based on continuous distribution kinetics was developed considering the interaction of the polymers through hydrogen abstraction and the parameters were evaluated numerically. The activation energies for the peroxide attack for the PCL and PVAC are 10.5 and , respectively. The activation energies for the random chain scission of PCL and PVAC are 10.6 and , respectively.