Effects of carbon nanotubes on rheological behavior in cellulose solution dissolved at low temperature

Multi-walled carbon nanotubes (MWNTs) were dispersed, for the first time, in cellulose solution in 9.5 wt% NaOH/4.5 wt% thiourea aqueous system pre-cooled to −5 °C. Dynamic light scattering and transmission electron microscopy results revealed a relatively strong interaction existed between MWNTs and the cellulose macromolecules, leading to a good dispersion of MWNTs in the cellulose solution. Their rheological behaviors, especially the sol-gel transition were investigated by using the advanced rheological expanded system on the basis of Winter and Chambon theory. The gel point and gel concentration of the cellulose/MWNTs solution system were determined, indicating a regularly rheological behavior. The data of loss tangent and relaxation exponent (n) indicated an enhancement in the viscoelasticity of the MWNTs/cellulose system. The results from scaling law before and beyond the sol-gel transition in the MWNTs/cellulose system confirmed that the cluster formation and alteration of the gelation structure occurred at the gel point. Interestingly, the n values calculated by both the Winter and Chambon theory and scaling law were coincident only at relatively low temperature. The predicted gel strength values of the MWNTs/cellulose system were significantly larger than the pure cellulose solution, suggesting a relatively high strength, supported by the mechanical strength of the cellulose/MWNTs material.     

RAFT-mediated polymerization and grafting of sodium 4-styrenesulfonate from cellulose initiated via γ-radiation

Ambient temperature (20 °C) reversible addition fragmentation chain transfer (RAFT) polymerization of sodium 4-styrenesulfonate (SS) conducted directly in aqueous media under γ-irradiation at different dose rates (0.09, 0.03 and 0.02 kGy h⁻¹) proceeds in a controlled fashion (typically, M_w/M_n < 1.25) to near quantitative conversions via 4-cyanopentanoic acid dithiobenzoate (CPADB) mediation. By applying CPADB modified cellulose as a macro chain transfer agent, a graft copolymer with SS was prepared in aqueous media under γ-irradiation. RAFT mediated graft polymerizations provided copolymers with higher graft frequencies compared to those obtained by conventional methods. Thermally initiated grafting of SS from a CPADB-functionalized cellulose surface at 70 °C was also studied which resulted in a reduced graft frequency in comparison to γ-initiated ones.     

Effects of CaTiO3 addition on the densification and microwave dielectric properties of BiSbO4 ceramics

In this study, the effects of CaTiO₃ addition on the sintering characteristics and microwave dielectric properties of BiSbO₄ were investigated. Pure BiSbO₄ achieved a sintered density of 8.46 g/cm³ at 1100 °C. The value of sintered density decreased with increasing CaTiO₃, and sintering at a temperature higher than 1100 °C led to a large weight loss (>2 wt%) caused by the volatile nature of the compound. Samples either sintered above 1100 °C or with a CaTiO₃ content exceeding 3 wt% showed poor densification. SEM micrographs revealed microstructures with bimodal grain size distribution. The size of the smaller grains ranged from 0.5 to 1.2 μm and that of the larger grains between 3 and 7 μm. The microwave dielectric properties of the (1−x) BiSbO_4−x CaTiO₃ ceramics are dependent both on the x value and on the sintering temperature. The 99.0 wt% BiSbO₄–1.0 wt% CaTiO₃ ceramic sintered at 1100 °C reported overall microwave dielectric properties that can be summarized as ε_r≈21.8, Q×f≈61,150 GHz, and τ_f≈−40.1 ppm/°C, all superior to those of the BiSbO₄ ceramics sintered with other additives.     

New soluble unsaturated polyketone derived from diarylidenecycloalketone: synthesis and optical and electrochemical properties of π-conjugated poly(diarylidenecyclohexanone) with long side chains

A new type of unsaturated polyketone having cyclohexanone moiety in a π-conjugated main chain was prepared by polycondensation between 2,6-bis(4-bromobenzylidene)cyclohexanone and 2,5-dihexyloxy-p-phenylene diboric ester in the presence of Pd(PPh₃)₄. The polymer had good solubility in common organic solvents. Analysis by gel permeation chromatography (GPC; polystyrene standards) showed that the polymer had M_n and M_w values of 7800 and 18?200, respectively. The polymer exhibited a [η] value of 0.70 dl g⁻¹ in benzene at 30 °C. The chloroform solution of the polymer showed an UV-Vis peak at 392 nm, and the PL spectrum gave a peak at 533 nm. DSC exhibited that the polymer had a T_g of 85 °C. The DSC data, observation with a polarizing microscope, X-ray diffraction data and UV-Vis data of the obtained polymer showed a phase transition above 200 °C. TGA showed that the polymer had good thermal stability with 5 wt% loss temperature of 407 °C under N₂. Electrochemical oxidation (or p-doping) of the polymer started at about 0.7 V vs. Ag/AgNO₃ and gave a peak at 1.06 V vs. Ag/AgNO₃ with a color change of the film from yellow to deep red. The color change was followed by UV-Vis spectroscopy. The corresponding p-dedoping peak appeared at 0.58 V vs. Ag/AgNO₃.     

Thermo-sensitive sol-gel transition of poly(depsipeptide-co-lactide)-g-PEG copolymers in aqueous solution

A series of biodegradable graft copolymers composed of poly(ethylene glycol) side-chains and a poly(depsipeptide-co-dl-lactide) backbone (PDG-dl-LA-g-PEG) were prepared as a novel thermo-gelling system. An aqueous solution of PDG-dl-LA-g-PEG (20 wt%) with a certain PEG length and composition showed instantaneous temperature-sensitive gelation at 33 °C. The sol-gel transition temperature (T_gel) could be controlled from 33 to 51 °C by varying the PEG length and compositions without a decrease in mechanical strength of the hydrogels. The 20 wt% hydrogel was eroded gradually in PBS at 37 °C for 60 days. This research provides a molecular design approach to create biodegradable thermo-gelling polymers with controllable T_gel and mechanical toughness.     

Dielectric properties of B2O3-doped 0.98CeO2–0.02CaTiO3 ceramics at microwave frequency

Microwave dielectric properties and microstructure of 0.98CeO₂–0.02CaTiO₃ ceramics with B₂O₃ additions prepared with the conventional solid-state route have been investigated. 0.98CeO₂–0.02CaTiO₃ ceramics can be sintered at 1290 °C for 4 h due to the sintering aid effect resulting from the B₂O₃ additions. At sintering temperature of 1380 °C for 4 h, 0.98CeO₂–0.02CaTiO₃ ceramics with 0.25 wt% B₂O₃ addition possess a dielectric constant (?_r) of 21.3, a Q × f value of 60,000 (at 8 GHz) and a temperature coefficient of resonant frequency (τ_f) of −41 ppm/°C.     

Synthesis and electrical conductivity of La-Sr-X-Mg-O (X = Ti, Zr, Al) perovskite solid solution

Perovskite solid solutions of (La_0.6Sr_0.4)(X_1−yMg_y)O_3−δ (X = Ti, Zr, Al) were prepared by a coprecipitation method using corresponding aqueous solutions and ammonium carbonate solution. The freeze-dried powders were sintered in air at 1000-1500 °C for 1-36 h. Single phase solid solutions were produced in the compositions of (La_0.6Sr_0.4)(Zr_0.6Mg_0.4)O_3−δ and (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ where (3 − δ) < 3. For the compositions of X = Ti and Zr for y = 0.1 where (3 − δ) > 3, two phases including perovskite solid solution were produced at 1400-1500 °C. The stability of perovskite solid solution was closely related to the fraction of lattice oxygen atom (3 − δ). A relatively high conductivity was measured for (La_0.6Sr_0.4)(Al_0.9Mg_0.1)O_3−δ (σ = 4.15 × 10⁻⁴ S/cm at 600 °C, activation energy 113.4 kJ/mol). The influence of fraction of oxide ion vacancy on the activation energy was small for δ = 0.1-0.3 of perovskite solid solution.     

Direct synthesis of poly(l-lactic acid) in supercritical carbon dioxide with dicyclohexyldimethylcarbodiimide and 4-dimethylaminopyridine

The direct synthesis of poly(l-lactic acid) (PLLA) from an l-lactic acid oligomer has been performed in supercritical carbon dioxide (scCO₂) using an esterification promoting agent, dicyclohexyldimethylcarbodiimide (DCC), and 4-dimethylaminopyridine (DMAP) as a catalyst. PLLA within M_n of 13,500 g/mol was synthesised in 90% yield at 3500 psi and 80 °C after 24 h. The molecular weight distribution of the products was narrower than PLLA prepared with melt-solid phase polymerisation under conventional conditions. Both DCC and DMAP showed high solubility in scCO₂ (DCC: 7.6 wt% (1.63×10⁻² mol/mol CO₂) at 80 °C, 3385 psi, DMAP: 4.5 wt% (1.62×10⁻²mol/mol CO₂) at 80 °C, 3386 psi) and supercritical fluid extraction was found to be effective at removing excess DMAP and DCC after the polymerisation was complete. We show that DCC and DMAP are effective esterification promoting reagents with further applications for condensation polymerisations in scCO₂.     

X-ray studies of regenerated cellulose fibers wet spun from cotton linter pulp in NaOH/thiourea aqueous solutions

Regenerated cellulose fibers were fabricated by dissolution of cotton linter pulp in NaOH (9.5 wt%) and thiourea (4.5 wt%) aqueous solution followed by wet-spinning and multi-roller drawing. The multi-roller drawing process involved three stages: coagulation (I), coagulation (II) and post-treatment (III). The crystalline structure and morphology of regenerated cellulose fiber was investigated by synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. Results indicated that only the cellulose II crystal structure was found in regenerated cellulose fibers, proving that the cellulose crystals were completely transformed from cellulose I to II structure during spinning from NaOH/thiourea aqueous solution. The crystallinity, orientation and crystal size at each stage were determined from the WAXD analysis. Drawing of cellulose fibers in the coagulation (II) bath (H₂SO₄/H₂O) was found to generate higher orientation and crystallinity than drawing in the post-treatment (III). Although the post-treatment process also increased crystal orientation, it led to a decrease in crystallinity with notable reduction in the anisotropic fraction. Compared with commercial rayon fibers fabricated by the viscose process, the regenerated cellulose fibers exhibited higher crystallinity but lower crystal orientation. SAXS results revealed a clear scattering maximum along the meridian direction in all regenerated cellulose fibers, indicating the formation of lamellar structure during spinning.     

Use of bulk liquid membrane for the removal of chromium (VI) from aqueous acidic solution with tri-n-butyl phosphate as a carrier

Tri-n-butyl phosphate (TBP) was used as carrier for the transport of chromium (VI) through a hexane bulk liquid membrane. The transport efficiency of chromium (VI) by TBP was investigated under various experimental conditions such as pH of the feed phase (Cr (VI) solution), concentration of the receiving phase (NaOH solution), concentration of TBP in membrane, rate of stirring, effect of transport time, type of solvent, Cr (VI) concentration in feed phase, and effect of temperature. The transport efficiency increased with increasing carrier concentration from 7.5 × 10^− 2 to 2.25 × 10^− 1 mol/L. At high pH (donor phase) the transport rate of chromate ions decreased. At high stirring speed (300 rpm) the Cr (VI) transport from the feed phase to the strip phase was completed within 5 h at 27 °C. Under optimum conditions: donor phase 4.8 × 10^− 4 mol/L K₂Cr₂O₇ solution at pH 1.0 ± 0.1, acceptor phase 1.0 mol/L NaOH solution, membrane phase 2.25 × 10^− 1 mol/L, stirring speed 300 rpm, and temperature 27 °C, the flux rate was found to be 2.90 × 10^− 7 mol/m² s.     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Monodisperse, micrometer-sized low molar mass polystyrene particles by two-stage dispersion polymerization

Free-radical dispersion polymerization of styrene was carried out in ethanol and in ethanol-water mixtures in the absence and presence of carbon tetrabromide (CBr₄) as a chain transfer agent. When CBr₄ was present at the onset of the reaction, particles with a broad size distribution were obtained. If, however, the addition of CBr₄ was delayed ca 1 h, so that the particle nucleation step was complete, then 1-2 wt% chain transfer agent, dissolved in monomer plus solvent, could be added to the reaction without a deleterious affect on particle formation. The particle size and size distribution was essentially identical to that obtained in the absence of CBr₄. When more CBr₄ was added, other problems arose. These problems appeared to be due to solubility of low molar mass polymer in the reaction medium. They could be overcome by running the reaction in ethanol-water mixtures (e.g. 5 wt% water) to decrease the solubility of oligo-styrene at 70 °C, the reaction temperature. In this way, monodisperse particles could be prepared in the presence of 3 wt% CBr₄ based upon total styrene, consisting of polymers with M_n=7060, M_w/M_n=2.4.     

Synthesis, characterization and optical properties of cross-linkable poly(phthalazinone ether ketone sulfone)

Cross-linkable poly(phthalazinone ether ketone sulfone) bearing tetrafluorostyrene groups (PPEKS-FSt) has been prepared by copolycondensation reaction for optical waveguide applications. The resulting amorphous polymer exhibits good solubility in some common polar organic solvents (e.g., N,N′-dimethylacetamide, N-methyl-2-pyrrolidinone, chloroform) at room temperature, and can be easily spin-coated into thin films with good optical quality. The glass transition temperature (T_g) and the temperature of 1% weight loss (1% T_d) are 261 °C and 494 °C, respectively, which could be further increased by 31 °C and 14 °C upon thermal cross-linking. The cross-linked polymer thin films exhibit high refractive index (∼1.65, TE mode), high thermo-optic coefficient value (dn/dT) (−1.455 × 10⁻⁴/°C, TE mode), low optical loss (less than 0.24 dB/cm at 1310 nm) and relatively low birefringence (∼0.007).     

Low temperature sintering and microwave dielectric properties of Ce2(WO4)3 ceramics

Ce₂(WO₄)₃ ceramics have been synthesized by the conventional solid-state ceramic route. Ce₂(WO₄)₃ ceramics sintered at 1000 °C exhibited ?_r = 12.4, Qxf = 10,500 GHz (at 4.8 GHz) and τ_f = −39 ppm/°C. The effects of B₂O₃, ZnO–B₂O₃, BaO–B₂O₃–SiO₂, ZnO–B₂O₃–SiO₂ and PbO–B₂O₃–SiO₂ glasses on the sintering temperature and microwave dielectric properties of Ce₂(WO₄)₃ were investigated. The Ce₂(WO₄)₃ + 0.2 wt% ZBS sintered at 900 °C/4 h has ?_r = 13.7, Qxf = 20,200 GHz and τ_f = −25 ppm/°C.     

Structural and surface properties of thermally prepared Ti/RhxTi(1−x)Oy electrodes: I—influence of preparation parameters

Electrodes of Rh_xTi_(1−x)O_y nominal composition were prepared by thermal decomposition of the chloride or nitrate precursor salts dissolved in strongly acidic medium and applied by brush to both sides of a Ti° support. A systematic study of the influence of calcination temperature and time as well as oxygen flux was conducted. The coatings were characterised by SEM, EDAX, XRD, open circuit potential measurements and cyclic voltammetry (CV). Visible-ultraviolet spectrophotometry was employed to identify the chemical form of the precursor in solution while thermogravimetric analysis (TGA) was used to assess the decomposition temperature ranges. Optimisation of the coating preparation parameters showed coatings obtained from [Rh(H₂O)₆](NO₃)₃ precursor dissolved in HNO₃ 1:2 (v/v) and fired at 430 °C for 2 h in a 5 l min⁻¹ oxygen stream-furnished stable electrodes having the highest electrochemically active surface area.     

A model for initial-stage sintering thermodynamics of an alumina powder

A model was proposed to calculate several thermodynamic parameters for the initial-stage sintering of an alumina powder obtained after calcinations at 900 °C for 2 h of a precursor. The precursor was synthesized by an alumina sulphate-excess urea reaction in boiling aqueous solution. The cylindrical compacts of the powder with a diameter of 14 mm were prepared under 32 MPa by uniaxial pressing using oleic acid (12% by mass) as binder. The compacts were fired at various temperatures between 900 and 1400 °C for 2 h. The diameter (D) of the compacts before and after firing was measured by a micrometer. The D value after firing was taken as a sintering equilibrium parameter. An arbitrary sintering equilibrium constant (K_a) was calculated for each firing temperature by assuming K_a = (D_i − D) / (D − D_f), where D_i is the largest value before sintering and D_f is the smallest value after firing at 1400 °C. Also, an arbitrary change in Gibbs energy (ΔG _a°) was calculated for each temperature using the K_a value. The graphs of ln K_avs. 1 / T and ΔG _a° vs. T were plotted, and the real change in enthalpy (ΔH°) and the real change in entropy (ΔS°) were calculated from the slopes of the obtained straight lines, respectively. Inversely, real ΔG° and K values were calculated using the real ΔH° and ΔS° values in the ΔG° = − RT ln K = ΔH° − TΔS° relation. The best fitting ΔH° and ΔS° values satisfying this relation were found to be 157,301 J mol^− 1 and 107.6 J K^− 1 mol^− 1, respectively.     

The porous network in carbon aerogels investigated by small angle neutron scattering

Small angle neutron scattering treated with the Porod approach has been applied to compare the influence of catalysts (C = NaOH, Na₂CO₃ and Ca(OH)₂) on the porous structure of resorcinol-formaldehyde (RF) carbon aerogels. Investigated parameters are the molar ratio (R/C varies from 10 to 800 mol/mol) and the pyrolysis temperature (1050 °C, 1700 °C and 2600 °C).At 1050 °C, carbon aerogels based on NaOH and Na₂CO₃ catalysts provide denser materials than with Ca(OH)₂-based one, due to a three-dimensional network of smaller particles. The density of particles decreases with the amount of catalyst. At 2600 °C the development of an intraparticle microporosity, which is quantified, leads to a slight decrease of the interparticle mesoporosity noticed at 1050 °C. This effect is induced by a stiffness of carbon layers in polyhedral pore walls as illustrated by the feature of the chords length distribution g(r) and TEM micrographs.     

Fluorescence quenching method for monitoring oxygen diffusion into PS/CNT composite films

Oxygen permeabilities of nanocomposite films consisting of multi wall carbon nanotubes (MWNT) and polystyrene (PS) were determined to investigate the oxygen diffusion depending on MWNT and temperature. A method which is based on quenching of an excited phosphorescent by oxygen was applied for the measurements. The composite films were prepared from mixtures of (MWNT) and surfactant-free pyrene (P)-labeled (PS) latexes of various compositions at room temperature. These films were then annealed at 170 °C which is well above the glass transition (T_g) temperature of polystyrene, for 10 min. Diffusion experiments were performed for eight films with different MWNT content (0, 1.5, 3, 5, 10, 15, 25 and 40 wt%) to evaluate the effect of MWNT content on oxygen diffusion. Diffusion coefficients were found to increase from 1.1 × 10⁻¹² to 41 × 10⁻¹² cm² s⁻¹ with increasing MWNT content. On the other hand, to examine the effect of temperature on oxygen diffusion, diffusion measurements were performed over a temperature range of 24–70 °C for three different MWNT contents (3, 15, and 40 wt%) within the films. The results indicated that the values of the diffusion coefficient D are strongly dependent on both temperature and MWNT content in the film. It was also observed that the diffusion coefficients obey Arrhenius behavior, from which diffusion energies were determined, which increased with increase of MWNT content and temperature.     

Effect of the addition ZrO2–Al2O3 on nanocrystalline hydroxyapatite bending strength and fracture toughness

Nanocrystalline hydroxyapatite powder has been synthesized from a Ca(NO₃)₂·4H₂O and (NH₄)₂HPO₄ solution by the precipitation method. In the next step we prepared ZrO₂–Al₂O₃ powder. After preparation, the powder was dried at 80 °C and calcined at 1200 °C for 1 h. Various amounts (HAP–15 wt% ZA, HAP–30 wt% ZA) of powder were mixed with the hydroxyapatite by ball milling. The powder mixtures were pressed and sintered at 1000 °C, 1100 °C and 1200 °C for 1 h. In order to study the structural evolution, X-ray diffraction (XRD) was used. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to estimate the particle size of the powder and observe fracture surfaces. Results show that the bending strength of pressed nanocrystalline HAP was improved significantly by the addition 15 wt% of ZrO₂–Al₂O₃ powders at 1200 °C, but the fracture toughness was not changed, however when 30 wt% of ZA powders were added to nanocrystalline HAP, the bending strength and fracture toughness of the specimens decreased at all sintering temperature.     

Radical copolymerization of (−)-menthyl 2-acetamidoacrylate and styrene or methyl methacrylate near ceiling temperature

Radical copolymerization of chiral monomer, (−)-menthyl 2-acetamidoacrylate (1), with low ceiling temperature (T_c = 62.0 °C in [monomer] = 1.0 mol/L) and styrene or methyl methacrylate (MMA) has been studied near ceiling temperature (60 °C) and at the temperature lower than T_c (30 °C). Monomer reactivity ratios and Alfrey-Price Q and e-values of 1 are estimated to be r₁ = 0.27, r₂ = 0.067, Q = 3.0, and e = 1.2 at 30 °C, and r₁ = 0.32 and r₂ = 0.046 at 60 °C for the copolymerization of 1 (M₁) and styrene (M₂), suggesting an alternating tendency at both temperatures, whereas for the copolymerization of 1 (M₁) and MMA (M₂) r₁ and r₂ are estimated to be 2.9 and 0.019 at 30 °C, respectively, indicating longer sequence length of 1. Specific rotation and circular dichroism of the resulting copolymer indicate that styrene, in particular, is effectively incorporated into a helical copolymer structure at 60 °C and even only 25 mol% incorporation of the acetamidoacrylate unit in the copolymer induces the helix formation in solution.