High-Performance $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ -Channel MOSFETs With High-$kappa$ Gate Dielectrics and $alpha$-Si Passivation

Long and short buried-channel $hbox{In}_{0.7}hbox{Ga}_{0.3}hbox{As}$ MOSFETs with and without $alpha$-Si passivation are demonstrated. Devices with $alpha$-Si passivation show much higher transconductance and an effective peak mobility of 3810 $hbox{cm}^{2}/ hbox{V} cdot hbox{s}$. Short-channel MOSFETs with a gate length of 160 nm display a current of 825 $muhbox{A}/muhbox{m}$ at $V_{g} - V_{t} = hbox{1.6} hbox{V}$ and peak transconductance of 715 $muhbox{S}/muhbox{m}$. In addition, the virtual source velocity extracted from the short-channel devices is 1.4–1.7 times higher than that of Si MOSFETs. These results indicate that the high-performance $hbox{In}_{0.7}hbox{Ga}_{0.3} hbox{As}$-channel MOSFETs passivated by an $alpha$ -Si layer are promising candidates for advanced post-Si CMOS applications.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

Comparative Study of the Low-Frequency-Noise Behaviors in a-IGZO Thin-Film Transistors With $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ Gate Dielectrics

A comparative study is made of the low-frequency noise (LFN) in amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) with $hbox{Al}_{2}hbox{O}_{3}$ and $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ gate dielectrics. The LFN is proportional to $hbox{1}/f^{gamma}$, with $gamma sim hbox{1}$ for both devices, but the normalized noise for the $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ device is two to three orders of magnitude lower than that for the $hbox{Al}_{2} hbox{O}_{3}$ device. The mobility fluctuation is the dominant LFN mechanism in both devices, but the noise from the source/drain contacts becomes comparable to the intrinsic channel noise as the gate overdrive voltage increases in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices. The $hbox{SiN}_{x}$ interfacial layer is considered to be very effective in reducing LFN by suppressing the remote phonon scattering from the $hbox{Al}_{2}hbox{O}_{3}$ dielectric. Hooge's parameter is extracted to $sim !!hbox{6.0} times hbox{10}^{-3}$ in $hbox{Al}_{2}hbox{O}_{3}/hbox{SiN}_{x}$ devices.      

Electrical Properties of $hbox{Bi}_{5}hbox{Nb}_{3} hbox{O}_{15}$ Thin Film Grown on $hbox{TiN}/hbox{SiO}_{2}/ hbox{Si}$ at Room Temperature for Metal–Insulator–Metal Capacitors

Buckling was observed in $hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15}$ (BiNbO) films grown on $hbox{TiN}/hbox{SiO}_{2}/hbox{Si}$ at 300 $^{circ}hbox{C}$ but not in films grown at room temperature and annealed at 350 $^{circ}hbox{C}$. The 45-nm-thick films showed a high capacitance density and a low dissipation factor of 8.81 $hbox{fF}/muhbox{m}^{2}$ and 0.97% at 100 kHz, respectively, with a low leakage current density of 3.46 $hbox{nA}/hbox{cm}^{2}$ at 2 V. The quadratic and linear voltage coefficients of capacitance of this film were 846 $hbox{ppm}/hbox{V}^{2}$ and 137 ppm/V, respectively, with a low temperature coefficient of capacitance of 226 $hbox{ppm}/^{circ}hbox{C}$ at 100 kHz. This suggests that a BiNbO film grown on a $hbox{TiN}/ hbox{SiO}_{2}/hbox{Si}$ substrate is a good candidate material for high-performance metal–insulator–metal capacitors.      

Electrical Properties of Amorphous $hbox{Bi}_{5} hbox{Nb}_{3}hbox{O}_{15}$ Thin Film for RF MIM Capacitors

Amorphous $hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15}(hbox{B}_{5} hbox{N}_{3})$ film grown at 300 $^{circ}hbox{C}$ showed a high-$k$ value of 71 at 100 kHz, and similar $k$ value was observed at 0.5–5.0 GHz. The 80-nm-thick film exhibited a high capacitance density of 7.8 fF/$muhbox{m}^{2}$ and a low dissipation factor of 0.95% at 100 kHz with a low leakage-current density of 1.23 nA/ $hbox{cm}^{2}$ at 1 V. The quadratic and linear voltage coefficient of capacitances of the $hbox{B}_{5}hbox{N}_{3}$ film were 438 ppm/$hbox{V}^{2}$ and 456 ppm/V, respectively, with a low temperature coefficient of capacitance of 309 ppm/$^{circ}hbox{C}$ at 100 kHz. These results confirmed the potential of the amorphous $hbox{B}_{5}hbox{N}_{3}$ film as a good candidate material for a high-performance metal–insulator–metal capacitors.      

Effective Modulation of Quadratic Voltage Coefficient of Capacitance in MIM Capacitors Using $hbox{Sm}_{2}hbox{O}_{3}/hbox{SiO}_{2}$ Dielectric Stack

We report the first demonstration of metal–insulator–metal (MIM) capacitors with $hbox{Sm}_{2}hbox{O}_{3}/hbox{SiO}_{2}$ stacked dielectrics for precision analog circuit applications. By using the “canceling effect” of the positive quadratic voltage coefficient of capacitance (VCC) of $hbox{Sm}_{2}hbox{O}_{3}$ and the negative quadratic VCC of $hbox{SiO}_{2}$, MIM capacitors with capacitance density exceeding 7.3 $hbox{fF}/muhbox{m}^{2}$ , quadratic VCC of around $-hbox{50} hbox{ppm/V}^{2}$ , and leakage current density of $hbox{1} times hbox{10}^{-7} hbox{A/cm}^{2}$ at $+$3.3 V are successfully demonstrated. The obtained capacitance density and quadratic VCC satisfy the technical requirements specified in the International Technology Roadmap for Semiconductors through the year 2013 for MIM capacitors to be used in precision analog circuit applications.      

Extraction of the Effective Mobility of $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs

The extraction of the effective mobility on $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ metal–oxide–semiconductor field-effect transistors (MOSFETs) is studied and shown to be greater than 3600 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$. The removal of $C_{rm it}$ response in the split $C$–$V$ measurement of these devices is crucial to the accurate analysis of these devices. Low-temperature split $C$–$V$ can be used to freeze out the $D_{rm it}$ response to the ac signal but maintain its effect on the free carrier density through the substrate potential. Simulations that match this low-temperature data can then be “warmed up” to room temperature and an accurate measure of $Q_{rm inv}$ is achieved. These results confirm the fundamental performance advantages of $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs.      

Second-Bit-Effect-Free Multibit-Cell Flash Memory Using $hbox{Si}_{3} hbox{N}_{4}/hbox{ZrO}_{2}$ Split Charge Trapping Layer

In this paper, a $hbox{Si}_{3}hbox{N}_{4}/hbox{ZrO}_{2}$ split charge trapping layer (SCTL) is proposed for multibit-cell Flash memory. The complementary potential wells of $hbox{Si}_{3}hbox{N}_{4}/hbox{ZrO}_{2}$ storage nodes enable independent node control when the Fowler–Nordheim (F–N) method is applied for programming/erasing (P/E). Experiment and simulation results suggest that the 2-bit (2-b) charge storage is accomplished by physical data node separation for the SCTL rather than charge injection control. The well-confined charge storages suppress the second-bit effect, enabling excellent 2-b data clearance for short-channel SCTL devices. It was found that the remaining memory windows after $hbox{10}^{5} hbox{s}$ decrease, dependent on the difference of the trap properties between $ hbox{Si}_{3}hbox{N}_{4}$ and $hbox{ZrO}_{2}$.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

Low Turn-On Voltage and High-Current $hbox{InP}/ hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Double Heterojunction Bipolar Transistors

We report on the dc and microwave characteristics of an $ hbox{InP/In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ double heterojunction bipolar transistor grown by solid-source molecular beam epitaxy. The pseudomorphic $hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}$ base reduces the conduction band offset $Delta E_{C}$ at the emitter/base junction and the base band gap, which leads to a very low $V_{rm BE}$ turn-on voltage of 0.35 V at 1 $hbox{A/cm}^{2}$ . A current gain of 125 and a peak $f_{T}$ of 238 GHz have been obtained on the devices with an emitter size of $hbox{1}times hbox{10} muhbox{m}^{2}$, suggesting that a high collector average velocity and a high current capability are achieved due to the type-II lineup at the InGaAsSb/InGaAs base/collector junction.      

High Microwave-Noise Performance of AlGaN/GaN MISHEMTs on Silicon With Gate Insulator Grown by ALD

High microwave-noise performance is realized in AlGaN/GaN metal–insulator semiconductor high-electron mobility transistors (MISHEMTs) on high-resistivity silicon substrate using atomic-layer-deposited (ALD) $hbox{Al}_{2}hbox{O}_{3}$ as gate insulator. The ALD $hbox{Al}_{2}hbox{O}_{3}/hbox{AlGaN/GaN}$ MISHEMT with a 0.25- $muhbox{m}$ gate length shows excellent microwave small signal and noise performance. A high current-gain cutoff frequency $f_{T}$ of 40 GHz and maximum oscillation frequency $f_{max}$ of 76 GHz were achieved. At 10 GHz, the device exhibits low minimum-noise figure $(hbox{NF}_{min})$ of 1.0 dB together with high associate gain $(G_{a})$ of 10.5 dB and low equivalent noise resistance $(R_{n})$ of 29.2 $Omega$. This is believed to be the first report of a 0.25-$muhbox{m}$ gate-length GaN MISHEMT on silicon with such microwave-noise performance. These results indicate that the AlGaN/GaN MISHEMT with ALD $hbox{Al}_{2}hbox{O}_{3}$ gate insulator on high-resistivity Si substrate is suitable for microwave low-noise applications.      

Fabrication and Properties of $hbox{Pt}/hbox{Bi}_{3.15}hbox{Nd}_{0.85} hbox{Ti}_{3}hbox{O}_{12}/breakhbox{HfO}_{2}/hbox{Si}$ Structure for Ferroelectric DRAM (FEDRAM) FET

Metal–ferroelectric–insulator–semiconductor (MFIS) capacitors with 400-nm-thick $hbox{Bi}_{3.15}hbox{Nd}_{0.85}hbox{Ti}_{3}hbox{O}_{12}$ (BNdT) ferroelectric film and 4-nm-thick hafnium oxide $(hbox{HfO}_{2})$ layer on silicon substrate have been fabricated and characterized. It is demonstrated that the $hbox{Pt}/hbox{Bi}_{3.15}hbox{Nd}_{0.85}hbox{Ti}_{3}hbox{O}_{12}/ hbox{HfO}_{2}/hbox{Si}$ structure exhibits a large memory window of around 1.12 V at an operation voltage of 3.5 V. Moreover, the MFIS memory structure suffers only 10% degradation in the memory window after $hbox{10}^{10}$ switching cycles. The retention time is 100 s, which is enough for ferroelectric DRAM field-effect-transistor application. The excellent performance is attributed to the formation of well-crystallized BNdT perovskite thin film on top of the $ hbox{HfO}_{2}$ buffer layer, which serves as a good seed layer for BNdT crystallization, making the proposed $hbox{Pt}/hbox{Bi}_{3.15}hbox{Nd}_{0.85}hbox{Ti}_{3}hbox{O}_{12}/ hbox{HfO}_{2}/hbox{Si}$ suitable for high-performance ferroelectric memories.      

1580-V–40-$hbox{m}Omegacdot hbox{cm}^{2}$ Double-RESURF MOSFETs on 4H-SiC $(hbox{000}bar{hbox{1}})$

Double-reduced-surface-field (RESURF) MOSFETs with $hbox{N}_{2}hbox{O}$ -grown oxides have been fabricated on the 4H-SiC $(hbox{000} bar{hbox{1}})$ face. The double-RESURF structure is effective in reducing the drift resistance, as well as in increasing the breakdown voltage. In addition, by utilizing the 4H-SiC $(hbox{000}bar{hbox{1}})$ face, the channel mobility can be increased to over 30 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, and hence, the channel resistance is decreased. As a result, the fabricated MOSFETs on 4H-SiC $( hbox{000}bar{hbox{1}})$ have demonstrated a high breakdown voltage $(V_{B})$ of 1580 V and a low on-resistance $(R_{rm ON})$ of 40 $hbox{m}Omega cdothbox{cm}^{2}$. The figure-of-merit $(V_{B}^{2}/R_{rm ON})$ of the fabricated device has reached 62 $hbox{MW/cm}^{2}$, which is the highest value among any lateral MOSFETs and is more than ten times higher than the “Si limit.”      

Improved Stress Reliability of Analog Metal–Insulator–Metal Capacitors Using $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Dielectrics

We have studied the stress reliability of high-$kappa$ $hbox{Ni/TiO}_{2}/hbox{ZrO}_{2}/hbox{TiN}$ metal–insulator–metal capacitors under constant-voltage stress. The increasing $hbox{TiO}_{2}$ thickness on $hbox{ZrO}_{2}$ improves the 125-$^{circ}hbox{C}$ leakage current, capacitance variation $(Delta C/C)$, and long-term reliability. For a high density of 26 $hbox{fF}/mu hbox{m}^{2}$ , good extrapolated ten-year reliability of small $Delta C/ break C sim hbox{0.71}%$ is obtained for the $ hbox{Ni/10-nm-}hbox{TiO}_{2}/hbox{6.5-nm-} hbox{ZrO}_{2}/break hbox{TiN}$ device at 2.5-V operation.      

Effect of Oxygen Pressure on the Electrical Properties of $hbox{Bi}_{5} hbox{Nb}_{3}hbox{O}_{15}$ Films Grown by RF Magnetron Sputtering

$hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15} (hbox{B}_{5}hbox{N}_{3})$ films grown under a low oxygen partial pressure (OP) of 1.7 mtorr showed a high leakage current density of 0.1 $hbox{A/cm}^{2}$ at 1.0 MV/cm. However, the leakage current density decreased with increasing OP to a minimum of $hbox{5.8} times hbox{10}^{-9} hbox{A/cm}^{2}$ for the film grown under 5.1 mtorr due to the decreased number of oxygen vacancies. This film also showed an improved breakdown field of 2.2 MV/cm and a large capacitance density of 24.9 $hbox{fF}/muhbox{m}^{2}$. The electrical properties of the film, however, deteriorated with a further increase in OP, which is probably due to the formation of oxygen interstitial ions. Therefore, superior electrical properties for the $ hbox{B}_{5}hbox{N}_{3}$ film can be obtained by careful control of OP.      

Resistive Switching Properties of $hbox{Au}/ hbox{ZrO}_{2}/hbox{Ag}$ Structure for Low-Voltage Nonvolatile Memory Applications

The reliable resistive switching properties of $hbox{Au}/hbox{ZrO}_{2}/ hbox{Ag}$ structure fabricated with full room temperature process are demonstrated in this letter. The tested devices show low operation voltages ($≪hbox{1}$ V), high resistance ratio (about $hbox{10}^{4}$), fast switching speed (50 ns), and reliable data retention (ten years extrapolation at both RT and 85 $^{circ}hbox{C}$). Moreover, the benefits of high yield and multilevel storage possibility make them promising in the next generation nonvolatile memory applications.      

Two-Pulse $C$–$V$ : A New Method for Characterizing Electron Traps in the Bulk of $ hbox{SiO}_{2}/hbox{high-}kappa$ Dielectric Stacks

$hbox{SiO}_{2}/hbox{high-}kappa$ dielectric stack is a candidate for replacing the conventional $hbox{SiO}_{2}$-based dielectric stacks for future Flash memory cells. Electron traps in the high-$ kappa$ layer can limit the memory retention via the trap-assisted tunneling, and there is a pressing need for their characterization. A new two-pulse $C$ –$V$ measurement technique is developed in this letter, which, for the first time, allows us to probe the discharge of electron traps throughout the $hbox{SiO}_{2}/hbox{high-}kappa$ stack. It complements the charge pumping technique, which can only probe near-interface traps. It is demonstrated that a large number of electron traps, indeed, exist in the bulk of high-$kappa$ layer. Bulk electron traps also have different discharge characteristics from those near the $hbox{SiO}_{2}/hbox{high-}kappa$ interface.      

Low-Voltage Organic Field-Effect Transistor With PMMA/$ hbox{ZrO}_{2}$ Bilayer Dielectric

This paper reports on the application of a bilayer polymethylmethacrylate (PMMA)/ $hbox{ZrO}_{2}$ dielectric in copper phthalocyanine (CuPc) organic field-effect transistors (OFETs). By depositing a PMMA layer on $hbox{ZrO}_{2}$, the leakage of the dielectric is reduced by one order of magnitude compared to single-layer $hbox{ZrO}_{2}$. A high-quality interface is obtained between the organic semiconductor and the combined insulators. By integrating the advantages of polymer and high- $k$ dielectrics, the device achieves both high mobility and low threshold voltage. The typical field-effect mobility, threshold voltage, on/off current ratio, and subthreshold slope of OFETs with bilayer dielectric are $hbox{5.6}timeshbox{10}^{-2} hbox{cm}^{2}/hbox{V} cdot hbox{s}$, 0.8 V, $hbox{1.2} times hbox{10}^{3}$, and 2.1 V/dec, respectively. By using the bilayer dielectrics, the hysteresis observed in the devices with single-layer $hbox{ZrO}_{2}$ is no longer present.      

A Center-Offset Polycrystalline-Silicon Thin-Film Transistor With ${rm n}^{+}$ Amorphous-Silicon Contacts

We have studied a bottom-gate polycrystalline-silicon thin-film transistor (poly-Si TFT) with amorphous-silicon (a-Si) ${rm n}^{+}$ contacts and center-offset gated structure, where intrinsic poly-Si is used in the center-offset region. The fabrication process is compatible with the conventional a-Si TFT with addition of thermal annealing for crystallization of a-Si. The bottom-gate poly-Si TFT with a 5-$muhbox{m}$ offset length exhibited a field-effect mobility of 18.3 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$ and minimum OFF-state current of $hbox{2.79} times hbox{10}^{-12} hbox{A}/muhbox{m}$ at $V_{rm ds} = hbox{5} hbox{V}$. The leakage currents are two orders of magnitude lower than those of a nonoffset TFT with mobility drop from 23.8 to 18.3 $hbox{cm}^{2}/ hbox{V} cdot hbox{s}$.      

Lattice-Mismatched $hbox{In}_{0.4}hbox{Ga}_{0.6} hbox{As}$ Source/Drain Stressors With In Situ Doping for Strained $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Channel n-MOSFETs

We report the first demonstration of a strained $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ channel n-MOSFET featuring in situ doped $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ source/drain (S/D) regions. The in situ silicondoped $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ S/D was formed by a recess etch and a selective epitaxy of $hbox{In}_{0.4}hbox{Ga}_{0.6}hbox{As}$ in the S/D by metal–organic chemical vapor deposition. A lattice mismatch of $sim$0.9% between $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ and $hbox{In}_{0.4} hbox{Ga}_{0.6}hbox{As}$ S/D gives rise to lateral tensile strain and vertical compressive strain in the $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ channel region. In addition, the in situ Si-doping process increases the carrier concentration in the S/D regions for series-resistance reduction. Significant drive-current improvement over the control n-MOSFET with Si-implanted $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ S/D regions was achieved. This is attributed to both the strain-induced band-structure modification in the channel that reduces the effective electron mass along the transport direction and the reduction in the S/D series resistance.