An implantable centrifugal blood pump for long term circulatory support

A compact centrifugal blood pump was developed as an implantable left ventricular assist system. The impeller diameter is 40 mm and the pump dimensions are 55 x 64 mm. This first prototype was fabricated from titanium alloy, resulting in a pump weight of 400 g including a brushless DC motor. Weight of the second prototype pump was reduced to 280 g. The entire blood contacting surface is coated with diamond like carbon to improve blood compatibility. Flow rates of over 7 L/min against 100 mmHg pressure at 2,500 rpm with 9 W total power consumption have been measured. A newly designed mechanical seal with a recirculating purge system ("Cool-Seal") is used as a shaft seal. In this seal system, seal temperature is kept under 40 degrees C to prevent heat denaturation of blood proteins. Purge fluid also cools the pump motor coil and journal bearing. The purge fluid is continuously purified and sterilized by an ultrafiltration filter incorporated into the paracorporeal drive console. In vitro experiments with bovine blood demonstrated an acceptably low hemolysis rate (normalized index of hemolysis = 0.005 +/- 0.002 g/100 L). In vivo experiments are currently ongoing using calves. Via left thoracotomy, left ventricular apex-descending aorta bypass was performed utilizing a PTFE (Polytetrafluoroethylene) vascular graft, with the pump placed in the left thoracic cavity. In two in vivo experiments, pump flow rate was maintained at 5-8 L/min, and pump power consumption remained stable at 9-10 W. All plasma free hemoglobin levels were measured at < 15 mg/dl. The seal system has demonstrated good seal capability with negligible purge fluid consumption (< 0.5 ml/ day). Both animals remain under observation after 162 and 91 days of continuous pump function.     

浅谈离心泵的故障诊断方法

本文针对离心泵的常见故障，提出了从性能参数、振动频率及烈度、轴承、轴封、管路系统、润滑油、冷却水等几方面是否正常来判断故障的所在位置、类型，并列举了工程中的实例加以说明．     

Left ventricular support with the implantable AB-180 centrifugal pump in sheep with acute myocardial infarction

A small, 257 g centrifugal pump was tested as a left ventricular assist device (LVAD) in sheep given a myocardial infarction. Pump performance, hemolysis, end organ function, weaning, explant procedure, and the incidence of thromboemboli at autopsy were studied over intervals of 1 to 44 days. Twelve sheep were given acute myocardial infarction by ligation of the anterior descending coronary artery and 11 had insertion of the AB-180 Circulatory Support System (CSS). One sheep served as a control for the space occupying effects of the pump in the left chest. Inflow was from the left atrium and outflow was to the descending thoracic aorta. Heparin (57-83 U/ml) in sterile water was infused into the pump at a rate of 10 ml/hr. Pump flows of 1-5.7 L/min were tested. The AB-180 CSS supported 73.5% of the total cardiac output (pump + heart) of 3.89 L/min, with a mean arterial pressure of 86 +/- 7 mmHg at a pump speed of 4,162 +/- 276 rpm immediately after implant. Hemolysis was <10 mg/dl and activated partial thromboplastin time (aPTT) values were in the normal range for sheep (<52 sec) after 48 hr of pumping. Liver enzyme concentrations returned to normal within 2 weeks. There was no evidence of thrombocytopenia. No signs of infection were present during assist and none was found at autopsy. The device was successfully removed three times without the use of pressor agents or blood transfusion. Alarm systems performed appropriately. During the 106 days of cumulative pumping, two sheep showed small (<1.5 cm) renal infarcts. Both were associated with intervals of pump stasis. The AB-180 CSS pump was easily implanted into the left chest without the use of cardiopulmonary bypass. It appears to have a low thromboembolic potential in sheep, without the need for large doses of heparin to elevate aPTT values. This characteristic may ameliorate the excessive bleeding seen clinically with current LVAD systems used for post cardiotomy cardiogenic shock, which require anticoagulation with heparin. The small size and weight of the device permit implantation within the chest and allow chest closure. This may reduce the incidence of infection associated with temporary left ventricular assist and an open sternum.     

Noninvasive pump flow estimation of a centrifugal blood pump

A flow rate estimating method was investigated for a centrifugal blood pump developed in our institute. The estimated flow rate was determined by the power consumption, the rotating speed of the motor, and the hematocrit value. The power consumption and the rotating speed of the motor were measured with a wattmeter. The examinations were performed in a closed mock loop filled with goat blood with hematocrit values of 21.5%, 28%, 34%, and 42%. Measured values of blood viscosity were 2.47, 3.09, 3.71, and 5.07 mPa.s at a share rate of 37.5/s, respectively. A linear correlation between the power consumption and the pump flow rate was observed in all hematocrit values. But variations in hematocrit caused a difference in the flow rate up to 1.1 L/min at the same power consumption and rotating speed. Effects of blood viscosity on the flow estimation were corrected by the hematocrit value. The value of the coefficient of determination, R2, between the estimated flow rate and the measured flow rate was 0.988. These results may indicate that the flow estimating method calculated by the power consumption of the motor, the rotating speed, and the hematocrit value is useful in the clinical situation.     

Heat generation and hemolysis at the shaft seal in centrifugal blood pumps

The heat and hemolysis around a shaft seal were investigated. Materials were original pumps (Nikkiso HMS-15:N-original, and 3M Delphin:D-original), vane-removed pumps (Nvane(-), Dvane(-)), and a small chamber with a shaft coiled by nichrome wire (mock pump). The original pumps were driven at 500 mmHg and 5 L/min, and vane-removed pumps were driven at the same rotation number. An electrical powers of 0, 0.5, 2, and 10 W was supplied to the mock pumps. In vitro hemolytic testing showed that hemolytic indices were 0.027 g/100 L in N-original, 0.013 in Nvane(-), 0.061 in D-original, and 0.012 in Dvane(-). Measurement of heat with a thermally insulated water chamber showed total heat within the pump of 8.62 and 10.85 W, and heat at the shaft seal of 0.87 and 0.62 W in the Nikkiso and Delphin pumps, respectively. Hemolysis and heat generation of mock pumps remained low. The results indicate that the heat generated around the shaft seal was minimal. Hemolysis at the shaft-seal was considerable but not major. Local heat did not affect hemolysis. It was concluded that the shaft-seal affected hemolysis, not by local heat but friction itself.     

Minimization of hemolysis in centrifugal blood pumps: influence of different geometries

Centrifugal blood pumps are of substantial importance for intraoperative extracorporeal circulation and for temporary cardiac assist. Their development and improvement raises many specific questions, especially on mechanical blood properties, flow distribution, and the resulting biocompatibility. In this comprehensive study the influence of various pump geometries on blood trauma was investigated. For this purpose analytical calculations, hydrodynamic performance, numerical simulation, in vitro hemolysis tests and in vivo experiments were used. The gap between rotor and housing was found to be crucial showing a distinct minimum of hemolysis at a gap of 1.5 mm (in vitro increase of plasma free hemoglobin per 100 ml plasma an hour: delta fHb/hour = 2.4 +/- 0.83 mg%/h at 1.5 mm versus 12 +/- 2.2 mg%/h at 2.5 mm; p < 0.05). Housing diameter and shape of the vanes were of less importance for blood traumatization (d = 60 mm: delta fHb/hour = 6.36 +/- 1.8 mg%/h; d = 70 mm: fHb = 7.1 +/- 1.9 mg%/h; straight radial vanes: 5.2 +/- 1.8 mg%/h; straight inclined vanes: 6.8 +/- 1.2 mg%/h; flexed vanes: 6.1 +/- 2.0 mg%/h). Three animal experiments confirmed the optimization of geometry, with a mean fHb of 2.5 to 3.2 mg% in steady state. Hydrodynamic efficiency revealed to be a necessary, but not a sufficient and sensitive criterion for hemolysis minimization (e.g. changes of eta < 10% for changes of fHb > 500%). Numerical simulation gives an improved insight in flow distribution, but can not yet be applied for quantification of blood trauma.(ABSTRACT TRUNCATED AT 250 WORDS)     

自来水厂串联离心泵的运行调试分析

对韶钢自来水厂二级泵房和西区加压泵房长距离输水管道串联离心泵在运行调试过程中出现的问题、故障原因进行分析及提出解决方法.     

A simple neonatal mock circulation enabling pulsatility and different hemodynamical states for neonatal ECMO research: application to assess the effect of a centrifugal pump operated neonatal ECMO system on the circulation

In the developing forebrain, mounting evidence suggests that neural stem cell proliferation and differentiation is regulated by growth factors. In vitro in the presence of serum, stem cell proliferation is predominantly mediated by fibroblast growth factor-2 (FGF-2) whereas neuronal differentiation can be triggered by FGF-1 in association with a specific heparan sulphate proteoglycan. On the other hand, astrocyte differentiation in vivo and in vitro appears to be dependent on signalling through the leukaemia inhibitory factor receptor (LIFR). The evidence suggests that in the absence of LIFR signalling, the stem cell population is present at approximately the same frequency and can generate neurons but is blocked from producing astrocytes that express glial fibrillary acidic protein (GFAP) or have trophic functions. The block can be overcome by other growth factors such as BMP-2/4 or interferon-gamma, providing further evidence that the inhibition to astrocyte development does not result from loss of a precursor population. Signalling through the LIFR, in addition to stimulating astrocyte differentiation, may also inhibit neuronal differentiation, which may explain why this receptor is expressed at the earliest stages of neurogenesis. Another signalling system which also exerts its influence on neurogenesis through active inhibition is Delta-Notch. We show in vitro that at high cell densities which impede neuronal production by FGF-1, lowering the levels of expression of the receptor Notch by antisense oligonucleotide results in a significant increase in neuronal production. Thus, stem cell differentiation appears to be dependent on the outcome of interactions between a number of signalling pathways, some which promote specific lineages and some which inhibit.     

Control of centrifugal blood pump based on the motor current

In this study, centrifugal pump performance was examined in a mock circulatory loop to derive an automatic pump rotational speed (rpm) control method. The pivot bearing supported sealless centrifugal pump was placed in the left ventricular apex to aorta bypass mode. The pneumatic pulsatile ventricle was used to simulate the natural ventricle. To simulate the suction effect in the ventricle, a collapsible rubber tube was placed in the inflow port of the centrifugal pump in series with the apex of the simulated ventricle. Experimentally, the centrifugal pump speed (rpm) was gradually increased to simulate the suction effect. The pump flow through the centrifugal pump measured by an electromagnetic flowmeter, the aortic pressure, and the motor current were continuously digitized at 100 Hz and stored in a personal computer. The analysis of the cross-spectral density between the pump flow and motor current waveforms revealed that 2 waveforms were highly correlated at the frequency range between 0 and 4 Hz, with the coherence and phase angles being close to 1.0 and 0 degree, respectively. The fast Fourier transform analysis of the motor current indicated that the second harmonic component of the motor current power density increased with the occurrence of the suction effect in the circuit. The ratio of the fundamental to the second harmonic component decreased less than 1.3 as the suction effect developed in the circuit. It is possible to detect and prevent the suction effect of the centrifugal blood pump in the natural ventricle through analysis of the motor current waveform.     

轧钢厂离心水泵气蚀现象分析

通过对负压提升式离心水泵气蚀现象的分析 ,阐述了负压提升式离心水泵产生气蚀的原因 ,说明了负压提升式离心水泵的几何安装高度与允许真空度的关系 ,用实例计算出海拔高度和水温对负压提升式离心水泵允许真空度的影响。     

Superiority of centrifugal pump over roller pump in paediatric cardiac surgery: prospective randomised trial

The perirhinal cortex (PRC) plays a major role in memory processes. This role may be influenced by activity in the adjacent entorhinal cortex (EC) and hippocampus (HPC), particularly during the processing of spatial information. In the current experiment we sought to determine whether the cholinergically mediated (type II) theta rhythm, which is a prominent electrophysiological feature of both HPC and EC activity, influenced neuronal firing in the PRC of urethane-anesthetized rats. When the spontaneous firing activity of single units recorded in PRC was related to theta recorded from the hippocampal fissure, it was determined that the firing of 50/163 (31%) PRC neurons exhibited a statistically significant phase relationship (mean phase angle = 188 degrees) to HPC theta. Thirty-three (66%) of these neurons tended to fire near the trough, and 17 near the peak, of this activity. These data indicate that a high proportion of PRC neurons participate in hippocampal-entorhinal theta activity. This activity may support information transmission and storage within and between these structures.     

Less blood damage in the impeller centrifugal pump: a comparative study with the roller pump in open heart surgery

A centrifugal pump with an impeller (Nikkiso Centrifugal Pump, Model HPM15; Nikkiso Co. Ltd.) was applied to cardiopulmonary bypass (CPB) in 14 patients who underwent elective coronary artery bypass grafting. Serum hemoglobin level, platelet count, and serum beta-thromboglobulin (beta TG) level were measured during CPB. The results were compared with those obtained in a comparative roller pump (RP) group (n = 10). There was no difference in the time on CPB between the NP (109 min) and RP (121 min) groups. The serum beta TG level (ng/ml) was lower in the NP group than in the RP group (obtained 90 min after the initiation of CPB). The plasma-free hemoglobin level also was lower in the NP group than in the RP group (obtained 90 min after the initiation of CPB, 120 min after the initiation of CPB, immediately after the termination of CPB, 3 h after termination of CPB; p < 0.01). There was no significant difference in platelet depletion. The HPM15 pump showed excellent hemodynamic performance with less blood trauma compared with the roller pump in its clinical application to open heart surgery.     

The monitoring of heparin activity during extracorporeal circulation

Heparin activity was assessed in 11 patients who underwent extracorporeal circulation for open-heart surgery. The activated partial thromboplastin time (A-PTT), thrombin time, protamine sulphate titration and factor Xa inhibition assay were used. The patients received heparin 3 mg/kg body weight, and 20 mg/450 ml blood was added to the pump. When the operative procedure was extended beyond 100 minutes patients received an additional 1,5 mg heparin/kg body weight. Protamine sulphate in a dose of 1,5 mg/1 mg heparin, was given to neutralize the heparin activity. The A-PTT was the easiest test which gave reliable results. The factor Xa inhibition assay measured heparin levels most precisely and mirrored the A-PTT results in all but one instance. These results indicate that the protocol employed produced adequate anticoagulation for the bypass procedure in all the patients. Protamine sulphate failed to neutralize heparin adequately after bypass in the 3 patients who received additional heparin during the surgical procedure. The monitoring of heparin activity during and after extracorporeal circulation is a desirable addition to open-heart surgical treatment.     

Breastfeeding support services in the neonatal intensive-care unit

OBJECTIVE: To describe a model for providing breastfeeding support in the neonatal intensive-care unit (NICU). DESIGN: Naturalistic, participant observation. SETTING: Suburban Level III NICU. PATIENTS: One hundred thirty-two mother-infant pairs over 1 year. Infants were hospitalized in the NICU, and mothers had initiated lactation efforts. INTERVENTIONS: Investigators provided breastfeeding interventions for the mother-infant pairs, based on identified problems, the research literature, or both. MAIN OUTCOME MEASURES: Percentage of mothers who were breastfeeding at the time of discharge from the NICU. RESULT: Interventions were classified into five categories: expression and collection of mothers' milk, gavage feeding of expressed mothers' milk, in-hospital breastfeeding sessions, postdischarge breastfeeding management, and additional consultation. CONCLUSIONS: This model was effective in preventing breastfeeding failure for this population. The model can provide the basis for NICU breastfeeding standards of care, protocols, and chart records, or for reimbursement purposes. The model also provides a framework for studying a specific category or breastfeeding intervention.     

Preclinical evaluation of the Kyocera Gyro centrifugal blood pump for cardiopulmonary bypass

The Kyocera Gyro pump has been developed as a completely seal-less centrifugal pump to overcome the problems of the conventional centrifugal pumps. The Gyro pump is a double pivot bearing-supported centrifugal pump with several specific design features, including its eccentric inlet port. We investigated the feasibility of the Gyro pump for cardiopulmonary bypass (CPB) in a bovine model, comparing it with the BioMedicus pump (BP-80). Ten healthy calves (5: Gyro pump, 5: BP-80) underwent 6 h of mildly hypothermic CPB at approximately 33 degrees C. Both pumps provided more than 50 ml/kg/min without any incidents. The haemodynamics of both groups remained stable within the normal range. All haematology and biochemistry data demonstrated no significant differences between the two groups. However, values of plasma-free haemoglobin and lactate dehydrogenase were less throughout the experiments of the Gyro pump than those of the BP-80. To obtain flow equivalent to that of the BP-80, the Gyro pump needed less rotational speeds than the BP-80 (2749.7 +/- 233.3 versus 3170.6 +/- 300.8 rpm. p < 0.05). Less rotational speed in addition to the difference in operating principle may contribute to less blood damage during the CPB OF the Gyro pump. After pumping for CPB, no leakage or thrombus formation was observed in either pump. The present study indicated that the Kyocera Gyro pump can be applied as a centrifugal pump for CPB with the same performance as the BP-80 and with relatively less haemolysis than the BP-80.     

Cannulation of neonates for venovenous extracorporeal life support

Venovenous access via a double-lumen cannula in the right internal jugular vein is the extracorporeal life support mode of choice for neonates with respiratory failure. We report a simplified method of cannulation. The advantages of this "semi-Seldinger" method include the ability to cannulate without ligating the internal jugular vein, and to adjust the position of the cannula and decannulate without re-exploring the wound.     

Current role of extracorporeal shockwave therapy in surgery

In urology the introduction of extracorporeal shockwave therapy brought a revolutionary change to the management of urinary calculi. This inspired the introduction of shockwave therapy in several fields of surgery; it has been applied as a potential alternative to several operative procedures but is still experimental. So far, the major application of shockwave therapy has been lithotripsy of stones in the gallbladder, common bile duct, pancreatic duct and salivary gland ducts. Other applications are in the non-operative management of bone healing disturbances and in the inhibition of tumour growth. Steps towards selective thrombus ablation and pretreatment of heavily calcified arteries have also been made. In this review, the applications of extracorporeal shockwave therapy in several areas of surgery are discussed. It is concluded that, for selected patients, shockwave treatment may serve as a useful addition to the surgical armamentarium.     

Three-dimensional numerical prediction of stress loading of blood particles in a centrifugal pump

The successful use of centrifugal pumps as temporary cardiac assist devices strongly depends on their degree of blood trauma. The mechanical stress loading experienced by cellular components on their passage through the pump is a major cause of blood trauma. Prediction of the mechanical stresses will assist optimization of pump design to minimize hemolysis and platelet activation. As a theoretical approach to this task., the determination of the complete three-dimensional (3D) flow field including all regions of high shear stress is therefore required. A computational fluid dynamics (CFD) software package, TASCflow, was used to model flow within a commercially available pump, the Aries Medical Isoflow Pump. This pump was selected in order to demonstrate the ability of the CFD software to handle complex impeller geometries. A turbulence model was included, and the Newtonian as well as the Reynolds stress tensor calculated for each nodal point. A novel aspect was the assignment of scalar stress values to streaklines representing particle paths through the pump. Scalar stress values were obtained by formulating a theory that enables the comparison of a three-dimensional state of stress with a uniaxial stress as applied in all mechanical blood damage tests. Stress loading-time functions for fluid particles passing inlet, impeller, and outlet domains of the pump were obtained. These showed that particles undergo a complex, irregularly fluctuating stress loading. Future blood damage theories would have to consider an unsteady stress loading regime that realistically reflects the flow conditions occurring within the pump.(ABSTRACT TRUNCATED AT 250 WORDS)