Crystallographic and dielectric aspects of Pb[(Mg,Zn)1/3Ta2/3]O3 system with 40 at.% Nb substitution

A total of 40 at.% Nb was substituted for Ta in the Pb[(Mg,Zn)_1/3Ta_2/3]O₃ system in order to enhance perovskite development. System powders were prepared by a B-site precursor method. Perovskite formation yields and lattice parameters of the pyrochlore/perovskite structures were determined from X-ray diffraction results. Weak-field low-frequency dielectric responses of the system ceramics were investigated as functions of temperature, composition, and frequency. Phase transition modes reflected in the dielectric constant spectra were further analyzed in terms of diffuseness parameters.     

Influence of Bi2O3 and CuO addition on low-temperature sintering and dielectric properties of Ba0.6Sr0.4TiO3 ceramics

In this study, we tried to lower the sintering temperature of Ba_0.6Sr_0.4TiO₃ (BST) ceramics by several kinds of adding methods of Bi₂O₃, CuO and CuBi₂O₄ additives. The effects of different adding methods on the microstructures and the dielectric properties of BST ceramics have been studied. In the all additive systems, the single addition of CuBi₂O₄ was the most effective way for lowering the sintering temperature of BST. When CuBi₂O₄ of 0.6 mol% was mixed with starting BST powders and sintered at 1100 °C, the derived ceramics demonstrated dense microstructure with a low dielectric constant (? = 4240), low dielectric loss (tan δ = 0.0058), high tunability (Tun = 38.3%) and high Q value (Q = 251). It was noteworthy that the sintering temperature was significantly lowered by 350 °C compared with no-additive system, and the derived ceramics maintained the excellent microwave dielectric properties corresponding to pure BST.     

Stoichiometric Pb(Mg1/3Nb2/3)O3 perovskite ceramics produced by reaction-sintering process

Stoichiometric lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃ (PMN), perovskite ceramics produced by reaction-sintering process were investigated. Without calcination, a mixture of PbO, Nb₂O₅, and Mg(NO₃)₂ was pressed and sintered directly. Stoichiometric PMN ceramics of 100% perovskite phase were obtained for 1, 2, and 4 h sintering at 1250 and 1270 °C. PMN ceramics with density 8.09 g/cm³ (99.5% of theoretical density 8.13 g/cm³) and K_max 19,900 under 1 kHz were obtained.     

Dielectric properties of (1−x)(Mg0.95Co0.05)TiO3-xCaTiO3 ceramic system at microwave frequency

The microwave dielectric properties and the microstructures of the (1−x)MgTiO₃-xCaTiO₃ ceramic system were investigated. With partial replacement of Mg by Co, dielectric properties of the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature. At 1275°C, the 0.95(Mg_0.95Co_0.05)TiO₃-0.05CaTiO₃ ceramics possesses excellent microwave dielectric properties: a dielectric constant ε_r of 20.3, a Q×f value of 107 000 ( at 7 GHz) and a τ_f value of −22.8 ppm/°C. By appropriately adjusting the x value in the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramic system, zero τ_f value can be achieved. With x=0.07, a dielectric constant ε_γ of 21.6, a Q×f value of 92 000 (at 7 GHz) and a τ_f value of −1.8 ppm/°C was obtained for 0.93(Mg_0.95Co_0.05)TiO₃-0.07CaTiO₃ ceramics sintered at 1275°C for 4 h.     

Microstructure and microwave dielectric characteristics of (1 − x)Ba(Zn1/3Ta2/3)O3-xBaTi4O9 ceramics

(1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ (0.1 ≤ x ≤ 0.85) composites are prepared by mixing 1150 °C-calcined BaTi₄O₉ with 1150 °C-calcined Ba(Zn_1/3Ta_2/3)O₃ powders. The crystal structure, microwave dielectric properties and sinterabilites of the (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics have been investigated. X-ray diffraction patterns reveal that BaTi₄O₉, ordered and disordered Ba(Zn_1/3Ta_2/3)O₃ phases exist independently over the whole compositional range. The sintering temperatures of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics are about 1240 - 1320 °C and obviously lower than those of Ba(Zn_1/3Ta_2/3)O₃ ceramics. The dielectric constants (?_r) and the temperature coefficient of resonant frequency (τ_f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of BaTi₄O₉ content. Nevertheless, the bulk densities and the quality values (Q × f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of Ba(Zn_1/3Ta_2/3)O₃ content. The results are attributed to the higher density and quality value of Ba(Zn_1/3Ta_2/3)O₃ ceramics, the better grain growth, and the densification of sintered specimens added a small BaTi₄O₉ content. The (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramic with x = 0.1 sintered at 1320 °C exhibits a ?_r value of 31.5, a maximum Q × f value of 68500 GHz and a minimum τ_f value of 4.1 ppm/°C.     

Microwave dielectric properties of (Pb1−3x/2Lax)(Mg1/2W1/2)O3

La modified Pb(Mg_1/2W_1/2)O₃ were prepared by solid-state reaction process, and the sintering behavior, microstructure and microwave dielectric properties were investigated by X-ray powder diffraction (XRD), Raman scattering and HP network analyzer in this paper. A series of single phase perovskite type solid solutions with A-site vacancies (Pb_1−3x/2La_x(Mg_1/2W_1/2)O₃ (0 ≤ x ≤ 2/3)) were formed. The solid solution took cubic perovskite type structure (Fm3m) with random distribution of A-site vacancies when 0 < x < 0.5, and tetragonal or orthorhombic structure with the ordering of A-site vacancies when 0.5 ≤ x ≤ 2/3. The dielectric constant and temperature coefficient of resonant frequency decrease with increasing La content. Relatively good combination microwave dielectric properties were obtained for x = 0.56: ?_r = 28.7; Q × f = 18098; and τ_f = −5.8 ppm/°C.     

Development of perovskite in Fe-substituted Pb(Zn1/3Ta2/3)O3 and dielectric characteristics

Pb(Zn_1/3Ta_2/3)O₃ ceramics, compositionally modified by the incorporation of Fe to the octahedral lattice sites, were prepared and characterized in terms of perovskite development, dielectric properties, as well as microstructure evolution. The powders of the B-site precursor compositions were synthesized separately and reacted with PbO to form Pb[(Zn_1/3Ta_2/3),(Fe_1/2Ta_1/2)]O₃. The perovskite contents increased continuously with the Fe concentration. The maximum dielectric constant values of the ceramics increased tremendously with the fraction of Fe, whereas the dielectric maximum temperatures were rather insensitive to the compositional change.     

Structure and ferroelectric properties in (K0.5Bi0.5)TiO3-BiScO3-PbTiO3 piezoelectric ceramic system

(K_0.5Bi_0.5)TiO₃-BiScO₃-PbTiO₃ ceramics were synthesized by conventional solid-state method. A morphotropic phase boundary (MPB) was confirmed with the aid of structural analysis. Two dielectric anomalous peaks were observed, the one around dielectric maximum temperature (T_m) due to phase transformation from ferroelectric to paraelectric while the second one could be ascribed to space charges. Furthermore, the existence of space charges also resulted in the independence of T_m with frequency at low lead composition. A new high temperature piezoelectric ceramic, 0.30(K_0.5Bi_0.5)TiO₃-0.30BiScO₃-0.40PbTiO₃ close to MPB exhibited excellent electrical properties with T_m of 384 °C, d₃₃ of 247 pC/N, k_p of 38.9%, P_r of 19.41 μC/cm², and E_c of 2.25 kV/mm, indicative of a candidate for high temperature application.     

Investigation of BiFeO3 modified PbTiO3-Bi(MgZr)O3-based complex perovskite ceramics

Bismuth containing crystalline solutions of (1 − x)Bi(MgZr)_0.5O₃-xPbTiO₃ (BMZ-PT) and [(BiFeO₃)_y − (BiMg_0.5Zr_0.5)_1−y]_x − [PbTiO₃]_1−x (BMZ-BF-PT) have been developed using conventional ceramic technology. X-ray diffraction analysis reveals that both the systems possess a perovskite structure, in which tetragonal to rhombohedral phase transformation appears for x = 0.55 in BMZ-PT and y = 0.20 in BMZ-BF-PT systems. SEM photographs reveal a uniform grain size distribution in the solid solution matrix with the presence of ferroelectric domains in few of the compositions. Ferroelectric hysteresis (polarization-electric field, P-E) loops reveal that increase in BiFeO₃ in BMZ-PT systems results in a decrease in residual polarization of the system with change and distortion in the shape of the (P-E) loops.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Low temperature sintering and microwave dielectric properties of SmAlO3 ceramics

The effects of sintering aids on the microstructures and microwave dielectric properties of SmAlO₃ ceramics were investigated. CuO and ZnO were selected as sintering aids to lower the sintering temperature of SmAlO₃ ceramics. With the additions, the sintering temperature of SmAlO₃ can be effectively reduced from 1650 to 1430°C. The crystalline phase exhibited no phase differences at low addition level while Sm₄Al₂O₉ appeared as a second phase as the doping level was over 0.5 wt.%. In spite of the additions, the dielectric constants showed no significant change and ranged 19-21. However, the quality factor Q×f was strongly dependent upon the type and amount of additions. The Q×f values of 51,000 and 41,000 GHz could be obtained at 1430°C with 0.25 wt.% CuO and ZnO additions, respectively. The temperature coefficients depended on the additions and varied from −40 to −65 ppm/°C. Results of X-ray diffractions, EDS analysis and scanning electron microscopy were also presented.     

Sintering and dielectric properties of 0.88Al2O3-0.12TiO2 microwave ceramics by glass addition

The microwave characteristics and the microstructures of 0.88Al₂O₃-0.12TiO₂ with various amounts of MgO-CaO-SiO₂-Al₂O₃ (MCAS) glass sintered at different temperatures have been investigated. The sintering temperature can be lowered to 1300 °C by the addition of MCAS glass. The densities, dielectric constants (ε_r) and quality values (Q×f) of the MCAS-added 0.88Al₂O₃-0.12TiO₂ ceramics decrease with the increase of MCAS glass content. The temperature coefficients of the resonant frequency (τ_f) are shifted to more negative values as the MCAS content or the sintering temperatures increase. The change of the crystalline phases of Al₂TiO₅ phase and rutile-TiO₂ phase has profound effects on the microwave dielectric properties of the MCAS-added Al₂O₃-TiO₂ ceramics. As sintered at 1250 °C, 0.88Al₂O₃-0.12TiO₂ ceramics with 2 wt.% MCAS glass addition exists a ε_r value of 8.63, a Q×f value of 9578 and a τ_f value of +5 ppm/°C.     

Improved microwave dielectric properties of B2O3-doped Nd(Co1/2Ti1/2)O3 ceramics with near zero temperature coefficient of resonant frequency

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ ceramics prepared by conventional solid-state route have been studied. The prepared Nd(Co_1/2Ti_1/2)O₃ exhibited a mixture of Co and Ti showing 1:1 order in the B-site. It is found that low-level doping of B₂O₃ (up to 0.75 wt.%) can significantly improve the density and dielectric properties of Nd(Co_1/2Ti_1/2)O₃ ceramics. Nd(Co_1/2Ti_1/2)O₃ ceramics with additives could be sintered to a theoretical density higher than 98.5% at 1320 °C. Second phases were not observed at the level of 0.25-0.75 wt.% B₂O₃ addition. The temperature coefficient of resonant frequency (τ_f) was not significantly affected, while the dielectric constants (?_r) and the unloaded quality factors Q were effectively promoted by B₂O₃ addition. At 1320 °C/4 h, Nd(Co_1/2Ti_1/2)O₃ ceramics with 0.75 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 27.2, a Q × f value of 153,000 GHz (at 9 GHz) and a temperature coefficient of resonant frequency (τ_f) of 0 ppm/°C. The B₂O₃-doped Nd(Co_1/2Ti_1/2)O₃ ceramics can find applications in microwave devices requiring low sintering temperature.     

Dielectric properties of B2O3-doped (1 − x)LaAlO3-xSrTiO3 ceramic system at microwave frequency

The effects of B₂O₃ addition on the microwave dielectric properties and the microstructures of (1−x)LaAlO₃-xSrTiO₃ ceramics prepared by conventional solid-state routes have been investigated. Doping with 0.25 wt.% B₂O₃ can effectively promote the densification and the microwave dielectric properties of (1−x)LaAlO₃-xSrTiO₃ ceramics. It is found that LaAlO₃-SrTiO₃ ceramics can be sintered at 1400°C due to the liquid phase effect of a B₂O₃ addition observed by scanning electronic microscopy (SEM). The dielectric constant as well as the Q×f value decreases with increasing B₂O₃ content. At 1460°C, 0.46LaAlO₃-0.54SrTiO₃ ceramics with 0.25 wt.% B₂O₃ addition possesses a dielectric constant (ε_r) of 35, a Q×f value of 38,000 (at 7 GHz) and a temperature coefficients of resonant frequency (τ_f) of −1 ppm/°C.     

Effect of B2O3-Bi2O3-SiO2-ZnO glass on the sintering and microwave dielectric properties of 0.83ZnAl2O4-0.17TiO2

The 0.83ZnAl₂O₄-0.17TiO₂ (ZAT) ceramics were synthesized by solid state ceramic route. The effect of 27B₂O₃-35Bi₂O₃-6SiO₂-32ZnO (BBSZ) glass on the microwave dielectric properties of ZAT was investigated. The crystal structure and the microstructure of the ceramic-glass composites were studied by X-ray diffraction and scanning electron microscopic techniques. The low frequency dielectric loss was measured at 1 MHz. The dielectric properties of the sintered samples were measured in the microwave frequency range by the resonance method. Addition of 0.2 wt% of BBSZ improved the dielectric properties with quality factor (Q_u × f) > 120,000 GHz, temperature coefficient of resonant frequency (τ_f) = −7.3 ppm/°C and dielectric constant (?_r) = 11.7. Addition of 10 wt% of BBSZ lowered the sintering temperature to about 950 °C with Q_u × f > 10,000 GHz, ?_r = 10 and τ_f = −23 ppm/°C. The reactivity of 10 wt% BBSZ added ZAT with silver was also studied. The results show that ZAT doped with suitable amount of BBSZ glass is a possible material for low-temperature co-fired ceramic (LTCC) application.     

Crystallographic and dielectric properties of barium-substituted Pb(Mg1/3Ta2/3)O3 ceramics

Ceramic powders of (Ba,Pb)Pb(Mg_1/3Ta_2/3)O₃ were prepared via a B-site precursor route. Crystal symmetries and lattice parameters were determined. Monophasic perovskite was developed after the two-step reaction process, in which the lattice parameters showed linear changes in the entire composition range. Dielectric responses of the ceramics with compositional and frequency changes were investigated. The results were also compared with the (Ba,Pb)(Zn_1/3Ta_2/3)O₃ data.     

Crystal structure and microwave dielectric properties of (1 − x)NdAlO3-xCaTiO3 ceramics

Crystal structure and microwave dielectric properties of (1−x)NdAlO₃-xCaTiO₃ ceramics have been investigated. Crystal structure of the specimens changed with the composition. Rhombohedral structure was found for the specimens with x≤0.1. When 0.3≤x≤0.7, the specimens had the tetragonal structure and it changed to the orthorhombic structure as x exceeded 0.7. Two types of the second phases were observed in (1−x)NdAlO₃-xCaTiO₃ ceramics. For the specimens with x≤0.5, Nd₄Al₂O₉ phase was observed and Al-rich phase was found in the specimens with x≥0.7. The dielectric constant (ε_r) and the temperature coefficient of the resonant frequency (τ_f) increased with the increase of x. The Q×f value of the specimen increased with x and exhibited the maximum value when x=0.5. The microwave dielectric properties of Q×f=45,000 GHz, ε_r=45 and τ_f=−1.5 ppm/°C were obtained for 0.3NdAlO₃-0.7CaTiO₃ ceramics.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Stabilization of α-SiAlONs using a rare-earth mixed oxide (RE2O3) as sintering additive

α-SiAlONs are commonly produced by liquid phase sintering of Si₃N₄ with AlN and Y₂O₃ as additives. The formation of the α-SiAlONs using a mixed oxide (RE₂O₃), containing yttria and rare-earth oxides, as an alternative additive was investigated. Dense α-SiAlONs were obtained by gas-pressure sintering, starting from α-Si₃N₄ and AlN-Y₂O₃ or AlN-RE₂O₃ as additives. The mixed oxide powder RE₂O₃ was characterized by means of high-resolution synchrotron X-ray diffraction and compared to Y₂O₃. The X-ray diffraction analysis of the mixed oxide shows a pattern indicating a true solid solution formation. The Rietveld refinement of the crystal structure of the sintered α-SiAlON using AlN-RE₂O₃ as additive revealed a similar crystal structure to the α-SiAlON using AlN-RE₂O₃ as additive. The comparison of the microstructures of the both α-SiAlONs produced using pure Y₂O₃ or RE₂O₃, revealed similar grain sizes of about 4.5 μm with aspect ratios of about 5. Both materials show also similar mechanical properties, with hardness of 18.5 GPa and fracture toughness of 5 MPa m^1/2. It could be, thus, demonstrated that pure Y₂O₃ can be substituted by the rare-earth solid solution, RE₂O₃, in the formation of α-SiAlONs, presenting similar microstructural and mechanical properties.     

Diffuse transition and piezoelectric properties of Pb[(Zr1−xTix)0.74(Mg1/3Nb2/3)0.20(Zn1/3Nb2/3)0.06]O3 Ceramics

In this work, the piezoelectric ceramic system of Pb[(Zr_1−xTi_x)_0.74(Mg_1/3Nb_2/3)_0.20(Zn_1/3Nb_2/3)_0.06]O₃, 0.47≤x≤0.57, with composition close to the morphotropic phase boundary, was studied. From the results of X-ray diffraction and piezoelectric measurement, ceramics near x=0.51 were found at the morphotropic phase boundary (MPB) between the tetragonal and pseudocubic perovskite. The planar coupling factor (k_p=0.72) is high at compositions near the MPB, but the mechanical quality factor (Q_m=75) is low. The calculation of the diffuseness of phase transition shows that the region of phase coexistence of this system is broader than that of the ternary system.