Study of Ln0.6Sr0.4Co0.8Mn0.2O3-δ (Ln=La, Gd, Sm or Nd) as the cathode materials for intermediate temperature SOFC

Perovskite type oxides Ln_0.6Sr_0.4Co_0.8Mn_0.2O_3−δ (Ln=La, Gd, Sm, or Nd) have been prepared by the solid state reaction of corresponding oxides. The crystal parameters of the compositions were determined by XRD powder diffraction, which revealed that all the compositions have orthorhombic structure. The reaction test of all samples with Ce_0.8Gd_0.2O_1.9 was carried out at 1200 °C for 48 h, and no reaction product was detected by XRD. The change in mass of La_0.6Sr_0.4Co_0.8Mn_0.2O_3−δ as a function of temperature was determined by thermogravimetric analysis (TGA). The electrical conductivity of the sintered samples were measured as a function of temperature from 200 to 1000 °C. The highest conductivity of about 1400 S cm⁻¹ was found in La_0.6Sr_0.4Co_0.8Mn_0.2O_3−δ. The cathodic polarization of these oxides electrodes deposited on Ce_0.8Gd_0.2O_1.9 tablet was studied at 500-800 °C in air.     

Electrochemical behaviors of Li[Li(1−x)/3Mn(2−x)/3Nix/3Cox/3]O2 cathode series (0 < x < 1) synthesized by sucrose combustion process for high capacity lithium ion batteries

A mixed cathode material between Li₂MnO₃ and Li[Mn_1/3Ni_1/3Co_1/3]O₂ for high capacity lithium secondary batteries was introduced in this study. It was prepared using the sucrose combustion process because this is a simple process. The oxidation states of Mn, Co and Ni ions in the pristine Li[Li_(1−x)/3Mn_(2−x)/3Ni_x/3Co_x/3]O₂ compounds were confirmed to be tetravalent, trivalent and divalent, respectively, via XANES measurements. Electrochemical charge/discharge studies showed that the highest first discharge capacity of 224 mAh/g was obtained in composition of x = 0.5 at a 0.2 C rate. The oxidation state of the Co and Ni ions in the Li[Li_1/6Mn_1/2Ni_1/6Co_1/6]O₂ changed to higher oxidation states, but that of the Mn ions did not change.     

Effect of B-site doping on Sm0.5Sr0.5MxCo1−xO3−δ properties for IT-SOFC cathode material (M = Fe, Mn)

The crystal structure, thermal expansion rate, electrical conductivity and electrochemical performance of Sm_0.5Sr_0.5M_xCo_1−xO_3−δ (M = Fe, Mn) have been investigated. Two crystal structures have been observed in the specimens of Sm_0.5Sr_0.5Fe_xCo_1−xO_3−δ (SSFC) at room temperature, the perovskite structure of SSFC has an orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5 ≤ x ≤ 0.9. The specimens of Sm_0.5Sr_0.5Mn_xCo_1−xO_3−δ (SSMC) crystallize in an orthorhombic structure. The adjustment of thermal expansion rate to electrolyte, which is one of the main problems of SSC, can be achieved to lower TEC values with more Fe and Mn substitution. Especially, Sm_0.5Sr_0.5Mn_0.8Co_0.2O_3−δ exhibits good thermal compatibility with La_0.8Sr_0.2Ga_0.8Mg_0.2O₃. High electrical conductivities are obtained for all the specimens and they demonstrate above 100 S/cm at 800 °C in SSFC system. The polarization resistance increases with increasing Mn content, Nevertheless, the polarization resistance of SSFC increases with increasing Fe content, but when the amount of Fe reaches to 0.4, the maximum is obtained while the resistance will decrease when the amount of Fe reaches above 0.4. Sm_0.5Sr_0.5Fe_0.8Co_0.2O_3−δ electrode exhibits high catalytic activity for oxygen reduction operating at temperature from 700 to 800 °C.     

Electrical conduction, dielectric behavior and magnetoelectric effect in (x)BaTiO3 + (1 − x)Ni0.94Co0.01Mn0.05Fe2O4 ME composites

Electrical and magnetoelectric properties of magnetoelectric (ME) composites containing barium titanate as electrical component and a mixed Ni-Co-Mn ferrite as the magnetic component are reported. The ME composites with a general formula (x)BaTiO₃ + (1 − x)Ni_0.94Co_0.01Mn_0.05Fe₂O₄ where x varies as 0, 0.55, 0.70, 0.85 and 1 were prepared by standard double sintering ceramic method. The presence of both the phases was confirmed by X-ray diffraction technique. The dc resistivity was measured as a function of temperature. The variation of dielectric constant (?) and loss tangent (tan δ) with frequency (100 Hz-1 MHz) and with temperature was studied. The conduction is explained on the basis of small polaron model based on ac conductivity measurements. The static value of ME conversion factor i.e. dc (ME)_H was studied as function of intensity of magnetic field. The changes were observed in dielectric properties as well as ME effect as the molar ratio of the components was varied. A maximum value of ME conversion factor of 610 μV/cm Oe was observed in the case of a composite containing 15 mol% ferrite phase.     

Preparation of ultra-fine cobalt-nickel manganite powders and ceramics derived from mixed oxalate

Co_0.30Ni_0.66Mn_2.04O₄ negative temperature coefficient ceramics were derived from mixed oxalate Co_0.30Ni_0.66Mn_2.04(C₂O₄)₃·nH₂O. The mixed oxalate was synthesized by milling a mixture of cobalt acetate, nickel acetate, manganese acetate, and oxalic acid at room temperature. An ultra-fine Co_0.30Ni_0.66Mn_2.04O₄ powder was obtained by calcining the mixed oxalate in air at 800 °C for 3 h. The oxide powder compact was sintered at a relatively low temperature of 1100 °C for 5 h, achieving a relative density of ∼98%. The specific resistivity ρ_25 °C and the thermal constant B_25/85 °C were 765.2 Ω cm and 3604 K, respectively. The resistance drift after aging at 150 °C for 500 h was 1.5%.     

Synthesis of xLi2MnO3·(1 − x)LiMO2 (M = Cr, Mn, Co, Ni) nanocomposites and their electrochemical properties

A series of 0.4Li₂MnO₃·0.6LiMO₂ (M = Ni_1/3Co_1/3Mn_1/3 and Ni_1/3Cr_1/3Mn_1/3) cathode materials are prepared by a co-precipitation method with subsequent quenching. Crystal structures of samples are investigated by X-ray diffraction and electron diffraction, which show a co-existence of rhombohedral and monoclinic structures indicating nanocomposite characteristics of the sample of 0.4Li₂MnO₃·0.6Li Ni_1/3Cr_1/3Mn_1/3O₂. The average particle size distributions of the powders are analyzed to be an order 400 and 100 nm. The 0.4Li₂MnO₃·0.6LiMO₂ (M = Ni_1/3Co_1/3Mn_1/3 and Ni_1/3Cr_1/3Mn_1/3) electrodes, which consist of a well balanced partial phases of rhombohedral and monoclinic can deliver a high reversible capacity of 220-230 mAh/g during an extended cycling.     

Tunable and microwave dielectric properties of Ba0.5Sr0.5TiO3-BaWO4 composite ceramics doped with Co2O3

Co₂O₃ doped BaWO₄-Ba_0.5Sr_0.5TiO₃ composite ceramics, prepared by solid-state route, were characterized systematically, in terms of their phase compositions, microstructure and microwave dielectric properties. Doping of Co₂O₃ promoted grain growth, reduced Curie temperature and broadened phase-transition temperature range of BaWO₄-Ba_0.5Sr_0.5TiO₃, which were attributed mainly to the substitution of Co³⁺ for Ti⁴⁺ at B site in the perovskite lattice. Dielectric diffusion behaviors of the composite ceramics were discussed. The composite ceramics all had dielectric tunability of higher than 10% at 30 kV/cm and 10 kHz, with promising microwave dielectric properties. Specifically, the sample doped with 0.2 wt.% Co₂O₃ exhibited a tunability of 20%, permittivity of 225 and Q of 292 (at 1.986 GHz), making it a suitable candidate for applications in electrically tunable microwave devices.     

Novel composite interconnecting ceramics La0.7Ca0.3CrO3−δ/Ce0.8Sm0.2O1.9 for solid oxide fuel cells

In this paper, an interconnecting ceramic for solid oxide fuel cells was developed, based on the modification from La_0.7Ca_0.3CrO_3−δ by addition of Ce_0.8Sm_0.2O_1.9. It is found that addition of small amount Ce_0.8Sm_0.2O_1.9 into La_0.7Ca_0.3CrO_3−δ dramatically increased the electrical conductivity. For the best system, La_0.7Ca_0.3CrO_3−δ + 5 wt.% Ce_0.8Sm_0.2O_1.9, the electrical conductivity reached 687.8 S cm⁻¹ at 800 °C in air. In H₂ at 800 °C, the specimen with 3 wt.% Ce_0.8Sm_0.2O_1.9 had the maximal electrical conductivity of 7.1 S cm⁻¹. With the increase of Ce_0.8Sm_0.2O_1.9 content the relative density increased, reaching 98.7% when the Ce_0.8Sm_0.2O_1.9 content was 10 wt.%. The average coefficient of thermal expansion at 30-1000 °C in air increased with Ce_0.8Sm_0.2O_1.9 content, ranging from 11.12 × 10⁻⁶ to 12.46 × 10⁻⁶ K⁻¹. The oxygen permeation measurement illustrated a negligible oxygen ionic conduction, indicating it is still an electronically conducting ceramic. Therefore, this material system will be a very promising interconnect for solid oxide fuel cells.     

Effects of Cr2O3 doping on the electrical properties and the temperature stabilities of PNW-PMN-PZT ceramics

The ceramics with 0.90Pb(Zr_0.50Ti_0.50)O₃-0.07Pb(Mn_1/3Nb_2/3)O₃-0.03Pb(Ni_1/2W_1/2)O₃ were prepared by adding Cr₂O₃. The effects of Cr₂O₃ doping on the phase structure, the microstructure and the electrical properties of ceramics were investigated. Meanwhile, the temperature stabilities of the resonant frequency (f_r) and the electromechanical coupling factor (K_p) were studied. The results showed that the better temperature stability could be obtained at x = 0.2 wt.% when the calcining temperature was 800 °C and the sintering temperature was 1150 °C. The parameters were Δf_r/f_r25 °C = −0.17% and ΔK_p/K_p25 °C = −1.39%. Moreover, the optimized electrical properties were also achieved, which were K_P = 0.54, Q_m = 1730, d₃₃ = 330 pC/N, ?_r = 2078 and tan δ = 0.0052. The optimized properties make the ceramics with this composition to be a good candidate for high power piezoelectric transformers applications.     

Mechanical and thermal properties of LaMgAl11O19

Lanthanum magnesium hexaaluminate (LaMgAl₁₁O₁₉) powders were synthesized successfully at 1300 °C for 4 h by solid-state reaction, and LaMgAl₁₁O₁₉ ceramic was prepared at 1700 °C for 6 h by pressureless sintering. Phase composition, microstructure, mechanical and thermophysical properties of LaMgAl₁₁O₁₉ ceramic were investigated. Results show that the flexural strength and fracture toughness of LaMgAl₁₁O₁₉ ceramic are 353.3 ± 12.5 MPa and 4.60 ± 0.46 MPa m^1/2. Young's Modulus and Poisson ratio is 295 GPa and 0.23, respectively. The linear thermal expansion coefficient of LaMgAl₁₁O₁₉ ceramic from 473 K to 1473 K is 9.17 × 10⁻⁶/K, and thermal conductivity at 1273 K is 2.55 W/m K.     

Electrochemical performance of La2NiO4+δ-La0.6Sr0.4Co0.2Fe0.8O3−δ composite cathodes for intermediate temperature solid oxide fuel cells

The composite cathodes La₂NiO_4+δ-La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ were prepared for intermediate temperature solid oxide fuel cells. La₂NiO_4+δ and La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ powders were synthesized successfully by glycine-nitrate process. The effect of composition on the electrochemical performance of the composite electrodes was studied by AC impedance spectroscopy and the optimal calcination temperature was determined when the electrode showed the minimum area specific resistance. The addition of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ to La₂NiO_4+δ electrode decreased the area specific resistance remarkably. The composite electrode with 30 wt% La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ calcined at 1150 °C exhibited the lowest area specific resistance of 0.125 Ω cm², about 60% of the area specific resistance of La₂NiO_4+δ electrode at 700 °C in air. The composite electrode with 30 wt% La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ can be a promising cathode material through the evaluation of electrical conductivity and thermal expansion behavior.     

Synthesis of layered Li1.2+x[Ni0.25Mn0.75]0.8−xO2 materials (0 ≤ x ≤ 4/55) via a new simple microwave heating method and their electrochemical properties

Li_1.2+x[Ni_0.25Mn_0.75]_0.8−xO₂ (0 ≤ x ≤ 4/55) was prepared by a new simple microwave heating method and the effect of extra Li⁺ content on electrochemistry of Li_1.2Ni_0.2Mn_0.6O₂ (x = 0) was firstly revealed. X-ray diffraction identified that they had layered α-NaFeO₂ structure (space group R-3m). Linear variation of lattice constant as a function of x value supported the formation of solid solution, that is, extra Li⁺ is possibly incorporated in structure of layered Li_1.2Ni_0.2Mn_0.6O₂ (x = 0), accompanying oxidization of Ni²⁺ to Ni³⁺ to form Li_1.2+x[Ni_0.25Mn_0.75]_0.8−xO₂ (0 ≤ x ≤ 4/55). This was confirmed by X-ray photoelectron spectroscopy that Ni³⁺ appeared and increased in content with increasing x value. Charge–discharge tests showed that Li_1.2+x[Ni_0.25Mn_0.75]_0.8−xO₂ (0 ≤ x ≤ 4/55) truly displayed different electrochemical properties (different initial charge–discharge plots, capacities and cycleability). Li_1.2Ni_0.2Mn_0.6O₂ (x = 0) in this work delivered the highest discharge capacity of 219 mAh g⁻¹ between 4.8 and 2.0 V. Increasing Li content (x value in Li_1.2+x[Ni_0.25Mn_0.75]_0.8−xO₂) reduced charge–discharge capacities, but significantly enhancing cycleability.     

Synthesis and electrochemical performances of spinel LiCr0.1Ni0.4Mn1.5O4 compound

The spinel compound LiCr_0.1Ni_0.4Mn_1.5O₄ was synthesized by a solid reaction method and a sol-gel method using citric acid as chelating agent. The pure phase LiCr_0.1Ni_0.4Mn_1.5O₄ was obtained by the wet method. The electrochemical performances of the pure phase sample were measured at different current rates. There were three voltage plateaus at about 4.9, 4.7 and 4.0 V in the charge-discharge curves, which were attributed to the oxidation/reduction of chromium, nickel and manganese respectively. In the range of 3.5-5.0 V, its first discharge capacity was 143, 118 and 111 mAh/g corresponding to current densities of 1.0, 4.0 and 5.0 mA/cm², respectively. After 50 cycles, the capacity retention remained well at the current densities of 1.0, 4.0 and 5.0 mA/cm². The electrochemical performances of pure phase LiCr_0.1Ni_0.4Mn_1.5O₄ at 55 °C was also measured, and the results were discussed.     

Composition dependent phase connectivity, dielectric and magnetoelectric properties of magnetoelectric composites with Pb(Mg1/3Nb2/3)0.67Ti0.33O3 as piezoelectric phase

Ferrite (Ni_0.6Co_0.4Fe₂O₄) phase, ferroelectric (Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃) phase and magnetoelectric composites of (x)Ni_0.6Co_0.4Fe₂O₄ + (1 − x)Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ with x = 0.15, 0.30 and 0.45 were prepared using solid-state reaction technique. Presence of Ni_0.6Co_0.4Fe₂O₄ and Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ was confirmed using X-ray diffraction technique. The scanning electron microscopic images were used to study the microstructure of the composites. Connectivity scheme present in the magnetoelectric (ME) composites are discussed from the microscopic images. Variation of dielectric constant and dielectric loss with temperature for all the composites was studied. Here we report the effect of Ni_0.6Co_0.4Fe₂O₄ mole fraction on connectivity schemes between Ni_0.6Co_0.4Fe₂O₄ and Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ composite. The variation of magnetoelectric voltage coefficient with dc magnetic field shows peak behaviour. The maximum value of magnetoelectric voltage coefficient of 9.47 mV/cm Oe was obtained for 0.15Ni_0.6Co_0.4Fe₂O₄ + 0.85Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ composites. Finally we have co-related the effect of Ni_0.6Co_0.4Fe₂O₄ content and dielectric properties on magnetoelectric voltage coefficient.     

High frequency magnetic mechanism of Ni-substituted Co2Z hexagonal ferrite

The magnetic properties, especially the high frequency magnetic mechanism, of Ni-substituted Co₂Z hexagonal ferrite were studied. The polycrystalline Z-type hexagonal ferrite of Ba₃Ni_xCo_2−xFe₂₄O₄₁ (0 ≤ x ≤ 2) were prepared by solid-state reaction. The results indicate that Ni-substituted Co₂Z samples all exhibit typical soft magnetic character. Substitution of Ni for Co will turn the planar magnetocrystalline anisotropy of Co₂Z to uniaxial anisotropy when x ≥ 1, so that the permeability drops dramatically and domain wall resonance appears in the frequency spectra. With the rise of Ni amount or sintering temperature, domain wall resonance strengthens gradually.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Improved microwave dielectric properties of B2O3-doped Nd(Co1/2Ti1/2)O3 ceramics with near zero temperature coefficient of resonant frequency

The microwave dielectric properties and the microstructures of Nd(Co_1/2Ti_1/2)O₃ ceramics prepared by conventional solid-state route have been studied. The prepared Nd(Co_1/2Ti_1/2)O₃ exhibited a mixture of Co and Ti showing 1:1 order in the B-site. It is found that low-level doping of B₂O₃ (up to 0.75 wt.%) can significantly improve the density and dielectric properties of Nd(Co_1/2Ti_1/2)O₃ ceramics. Nd(Co_1/2Ti_1/2)O₃ ceramics with additives could be sintered to a theoretical density higher than 98.5% at 1320 °C. Second phases were not observed at the level of 0.25-0.75 wt.% B₂O₃ addition. The temperature coefficient of resonant frequency (τ_f) was not significantly affected, while the dielectric constants (?_r) and the unloaded quality factors Q were effectively promoted by B₂O₃ addition. At 1320 °C/4 h, Nd(Co_1/2Ti_1/2)O₃ ceramics with 0.75 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 27.2, a Q × f value of 153,000 GHz (at 9 GHz) and a temperature coefficient of resonant frequency (τ_f) of 0 ppm/°C. The B₂O₃-doped Nd(Co_1/2Ti_1/2)O₃ ceramics can find applications in microwave devices requiring low sintering temperature.     

High rate performance of novel cathode material Li1.33Ni1/3Co1/3Mn1/3O2 for lithium ion batteries

Li_1.33Ni_1/3Co_1/3Mn_1/3O₂ with highly ordered structure has been successfully synthesized via a simple co-precipitation process. Charge–discharge tests showed that the initial discharge capacities are 153.0 mAh g⁻¹ and 128.9 mAh g⁻¹ at 5 C (1000 mA g⁻¹) and 10 C (2000 mA g⁻¹) between 2.5 and 4.5 V, respectively. The average full-charge time of this material is less than 12 min at 5 C and 6 min at 10 C. The electrode material composed of the prepared showed a better cyclability. The excellent high rate performance is attributed to the improved ordered layered structure and the electrical conductivity. The excess Li shorten Li⁺ diffusion distance between these submicron and nano-scaled particles. The results show that Li_1.33Ni_1/3Co_1/3Mn_1/3O₂ cathode material has potential application in lithium ion batteries.     

Electrical properties of MgAl2-2xZrxMxO4 (M = Co, Ni and x = 0.00-0.20) synthesized by coprecipitation technique using urea

This paper presents the results of a study concerning the structural and electrical properties of MgAl_2-2xZr_xM_xO₄ (x = 0.00-0.20 and M = Co²⁺ and Ni²⁺) prepared by a coprecipitation technique using urea as a precipitating agent. The X-ray diffraction data for the pure and its doped samples are consistent with the single-phase spinel and their crystallite sizes are in the range 7-20 ± 4 nm. The DC resistivity increases from 3.09 × 10⁹ Ω cm to 6.73 × 10⁹ and 8.06 × 10⁹ Ω cm whereas dielectric constant decreases from 5.80 to 5.11 and 4.95 on doping with Zr-Co and Zr-Ni, respectively. The electrical resistivity variations with increase in the dopant contents indicate two types of conduction mechanisms in operation. Several parameters such as, hopping energy (W), metal-semiconductor transition temperature (T_MS) and Debye temperature (θ_D) have also been determined. The increase in DC resistivity and decrease in dielectric constant suggest that the synthesized materials can be considered for application as an insulating and structural material in fusion reactors.     

Influence of isovalent ion substitution on the electrochemical performance of LiCoPO4

LiCo_1−xM_xPO₄ (M = Mg²⁺, Mn²⁺ and Ni²⁺; 0 ≤ x ≤ 0.2) compounds have been synthesized by solid-state reaction method and studied as cathode materials for secondary lithium batteries. LiCoPO₄ exhibits a discharge plateau at ∼4.7 V with an initial discharge capacity of 125 mAh/g and on cycling capacity falls. Substitution of Co²⁺ with Mg²⁺/Mn²⁺/Ni²⁺ in LiCoPO₄ has an influence on the initial discharge capacity and on cycling behaviour. The capacity retention of LiCoPO₄ is improved by manganese substitution. Among the manganese substituted phases, LiCo_0.95Mn_0.05PO₄ shows good reversible capacity of ∼50 mAh/g.