Photoluminescence and field-emission characteristics of ZnO nanowires synthesized by two-step method

ZnO nanowires with excellent photoluminescence (PL) and field-emission properties were synthesized by a two-step method, and the ZnO nanowires grew along (0 0 2) direction. PL measurements showed that the ZnO nanowires have stronger ultraviolet emission properties at 376 nm and there is 3 nm blue shift after the nanowires were immersed in thiourea (TU) solution compared with those of without immersion. The immersed-ZnO nanowires show a turn-on field of 2.3 V/μm at a current density of 0.1 μA/cm and emission current density up to 1 mA/cm² at an applied field of 6.8 V/μm, which demonstrate that the immersed-ZnO nanowires posses efficient field-emission properties in contrast with those not immersed. The ZnO nanowires may be ideal candidates for making luminescent devices and field-emission displays.     

Synthesis of naturally cross-linked polycrystalline ZrO2 hollow nanowires using butterfly as templates

Butterfly wing skeleton is a widely used hard-template in recent years for fabricating photonic crystal structures. However, the smallest construction units for the most species of butterflies are commonly larger than ∼50 nm, which greatly hinders their applications in designing much smaller functional parts down to real “nano scale”. This work indicates, however, that hollow ZrO₂ nanowires with ∼2.4 μm in length, ∼35 nm in diameter and ∼12 nm in wall thickness can be synthesized via the selection of suitable butterfly bio-templates followed by heat processing. Especially, the successful fabrication of these naturally cross-linked ZrO₂ nanotubes suggests a new optional approach in fabricating assembled nano systems.     

Field emission properties of electrodeposited cobalt nanowire arrays grown in anodic aluminum oxide

The excellent vertically aligned cobalt nanowire arrays were electrodeposited into anodic aluminum oxide (AAO) templates. Each nanowire has the same length with 20 μm and the diameter with 60 nm. The field emission characteristics of the nanowires were firstly studied based on current-voltage measurements and the Fowler-Nordheim equation. The electron field emission measurements on the samples showed a turn-on field (1 mA/cm²) of 1.66 V/μm, a field enhancement factor of β = 3054 and a current density of 600 mA/cm² at a relatively low voltage of 4.3 V/μm. The nanowire arrays could be an ideal alternative to carbon nanotubes and ZnO nanowires for the fabrication of flat panel displays.     

Vertically aligned Mn-doped zinc oxide nanorods by hybrid wet chemical route

Mn-doped zinc oxide (Mn:ZnO) nanorods were synthesized by incorporating manganese in aligned ZnO nanorods. For this, Mn was evaporated onto ZnO nanorods and the composite structure was subjected to rapid thermal annealing. The nanorods were preferentially oriented in (0 0 2) direction as indicated by the XRD measurement. Optical band gap was seen to decrease with increasing amount of Mn incorporation. XPS studies indicated that incorporated Mn was in Mn²⁺ and Mn⁴⁺ states. Mn²⁺ atomic concentration was found to be larger than Mn⁴⁺ concentration in all the samples. The Raman spectra of the Mn:ZnO nanorods indicated the presence of the characteristic peak at ∼438 cm⁻¹ for high frequency branch of E₂ mode of ZnO. The PL peak at ∼376 nm (∼3.29 eV) was ascribed to the band edge luminescence while the peak at ∼394 nm (∼3.15 eV) was assigned to the donor bound exciton (D^oX) and free exciton transition related to Mn²⁺ states.     

Growth specificity of vertical ZnO nanorods on patterned seeded substrates through integrated chemical process

A simple and cost effective method has been employed for the random growth and oriented ZnO nanorod arrays over as-prepared and patterned seeded glass substrates by low temperature two step growth process and growth specificity by direct laser writing (DLW) process. Scanning electron microscopy (SEM) images and X-ray diffraction analysis confirm the growth of vertical ZnO nanorods with perfect (0 0 2) orientation along c-axis which is in conjunction with optimizing the parameters at different reaction times and temperatures. Transmission electron microscopy (TEM) images show the formation of vertical ZnO nanorods with diameter and length of ∼120 nm and ∼400 nm respectively. Photoluminescence (PL) spectroscopic studies show a narrow emission at ∼385 nm and a broad visible emission from 450 to 600 nm. Further, site-selective ZnO nanorod growth is demonstrated for its high degree of control over size, orientation, uniformity, and periodicity on a positive photoresist ZnO seed layer by simple geometrical (line, circle and ring) patterns of 10 μm and 5 μm dimensions. The demonstrated control over size, orientation and periodicity of ZnO nanorods process opens up an opportunity to develop multifunctional properties which promises their potential applications in sensor, piezoelectric, and optoelectronic devices.     

Synthesis of ZnO flowers and their photoluminescence properties

Flower-like ZnO nano/microstructures have been synthesized by thermal treatment of Zn(NH₃)₄²⁺ precursor in aqueous solvent, using ammonia as the structure directing agent. A number of techniques, including X-ray diffraction (XRD), field emission scan electron microscopy (FESEM), transmission electron microscopy (TEM), thermal analysis, and photoluminescence (PL) were used to characterize the obtained ZnO structures. The photoluminescence (PL) measurements indicated that the as-synthesized ZnO structures showed UV (∼375 nm), blue (∼465 nm), and yellow (∼585 nm) emission bands when they were excited by a He-Gd laser using 320 nm as the excitation source. Furthermore, it has been interestingly found that the intensity of light emission at ∼585 nm remarkably decreased when the obtained ZnO nanocrystals were annealed at 600 °C for 3 h in air. The reason might be the possible oxygen vacancies and interstitials in the sample decreased at high temperature.     

Rapid preparation, characterization, and photoluminescence of ZnO films by a novel chemical method

A novel and simple chemical route was developed for the deposition of ZnO film from aqueous solution, integrating the merits of successive ionic layer adsorption and reaction and chemical bath deposition. ZnO thin films on glass and Si(1 0 0) substrates were deposited with the precursor of zinc-ammonia complex. As-deposited ZnO film exhibits good crystallinity with the hexagonal wurtzite crystalline structure and the preferential orientation along (0 0 2) plane. With a dense and continuous appearance, the film is composed of ZnO particles in even size of 200-300 nm. Under the excitation of 340 nm, strong and sharp near band gap emission (∼391 nm) dominates the photoluminescence spectra with several weak emission peaks related to the deep level (∼450-500 nm). In addition, the mechanism for the deposition process of ZnO from aqueous solution was preliminarily discussed.     

Fabrication of TiO2 nanotube film by well-aligned ZnO nanorod array film and sol-gel process

High density TiO₂ nanotube film with hexagonal shape and narrow size distribution was fabricated by templating ZnO nanorod array film and sol-gel process. Well-aligned ZnO nanorod array films obtained by aqueous solution method were used as template to synthesize ZnO/TiO₂ core-shell structure through sol-gel process. Subsequently, TiO₂ nanotube array films survived by removing the ZnO nanorod cores using wet-chemical etching. Polycrystalline anatase TiO₂ nanotube films were ∼ 1.5 μm long and ∼ 100 nm in inter diameter with a wall thickness of ∼ 10 nm.     

Synthesis of novel zinc oxide microphone-like microstructures

Novel microphone-like ZnO microstructures were grown at a very high density via a simple thermal evaporation process using commercially available ZnO powder in ambient air at ∼ 1050 ± 20 °C in 1 h. The unique as-grown microstructures were characterized in detail in terms of their structural and optical properties. The structural properties of the synthesized products confirmed that they were wurtzite hexagonal phase for the as-grown products. Raman-scattering spectra exhibited a strong and dominated Raman-active E₂ (high) mode at 441 cm^− 1, confirming the wurtzite hexagonal phase for the as-grown microphone-like ZnO morphologies. The cathodoluminescence (CL) spectrum shows a suppressed near band edge emission at ∼ 380 nm and strong green emission at ∼ 500 nm.     

Controlled density of vertically aligned carbon nanotubes in a triode plasma chemical vapor deposition system

We report on the growth mechanism and density control of vertically aligned carbon nanotubes using a triode plasma enhanced chemical vapor deposition system. The deposition reactor was designed in order to allow the intermediate mesh electrode to be biased independently from the ground and power electrodes. The CNTs grown with a mesh bias of + 300 V show a density of ∼ 1.5 μm^− 2 and a height of ∼ 5 μm. However, CNTs do not grow when the mesh electrode is biased to − 300 V. The growth of CNTs can be controlled by the mesh electrode bias which in turn controls the plasma density and ion flux on the sample.     

A template-free alcoholthermal route to Ti(Sn)-doped ZnO nanorods

Ti(Sn)-doped single-crystalline ZnO nanorods with an average diameter of 20 nm and length up to nearly 1 μm were synthesized by a facile ultrasonic irradiation-assisted alcoholthermal method without involving any templates. Photoluminescence spectra of the Ti-doped ZnO nanorods were measured at room temperature and three emitting bands, being a violet emission at 400-415 nm, a blue band at 450-470 nm and a green band at around 550 nm, were detected. The emission intensities of the Ti-doped ZnO nanorods enhance gradually with increasing the doping concentrations. As to the Sn-doped ZnO nanorods, the green emission shifts to 540 nm and the emission intensities increase first but decrease later with increasing the doping concentrations.     

Ni-doped vertically aligned zinc oxide nanorods prepared by hybrid wet chemical route

Ni-doped zinc oxide (Ni:ZnO) nanorods were synthesized by incorporating nickel in vertically aligned ZnO nanorods. Ni was evaporated onto ZnO nanorods and the composite structure was subjected to rapid thermal annealing for dispersing Ni in ZnO nanorods. The optical band gap decreased with increasing amount of Ni incorporation. The origin of the photoluminescence peak at ∼ 400 nm was related to the defect levels introduced due to substitution of Ni²⁺ in the Zn²⁺ site with annealing. The Raman spectra indicated the presence of the characteristic peak at ∼ 436 cm^− 1 which was identified as high frequency branch of E₂ mode of ZnO. The Fourier Transformed Infrared spectra indicated the existence of the distinct characteristic absorption peak at 481 cm^− 1 for ZnO stretching modes. Current-voltage characteristics indicated that the current changed linearly with voltage for both the doped and undoped samples.     

Potentiometric cholesterol biosensor based on ZnO nanorods chemically grown on Ag wire

An electrochemical biosensor based on ZnO nanorods for potentiometric cholesterol determination is proposed. Hexagon-shaped ZnO nanorods were directly grown on a silver wire having a diameter of 250 μm using low temperature aqueous chemical approach that produced ZnO nanorods with a diameter of 125-250 nm and a length of ~ 1 μm. Cholesterol oxidase (ChOx) was immobilized by a physical adsorption method onto ZnO nanorods. The electrochemical response of the ChOx/ZnO/Ag biosensor against a standard reference electrode (Ag/AgCl) was investigated as a logarithmic function of the cholesterol concentration (1 × 10⁻⁶ M to 1 × 10⁻² M) showing good linearity with a sensitivity of 35.2 mV per decade and the stable output signal was attained at around 10 s.     

Synthesis of nanometal oxides and nanometals using hot-wire and thermal CVD

We report the synthesis of nano-oxides of molybdenum, tungsten, and zinc. Molybdenum oxide (MoO₃) and tungsten oxide (WO_x) were produced by hot-wire CVD with molybdenum and tungsten filaments, respectively while zinc oxide (ZnO) was produced by thermal CVD. When high purity molybdenum wire was oxidized at ambient system atmosphere, nanorods and nanostraws of MoO₃ with length ranging from ∼ 20-80 nm and diameters ranging from ∼ 5-15 nm were produced. Also, the oxidation of the tungsten filament led to the deposition of tungsten oxide nanorods (10-25 nm diameter and 75-90 nm long) and nanospheres with diameters of ∼ 60 nm. Each oxide was reduced to its metallic form by annealing in a hydrogen environment to produce metallic nanoparticles. Nanorods and nanoribbons of ZnO with diameters ranging from 20-65 nm and lengths up to 2 μm were also produced.     

Synthesis, characterization and properties of carbon nanotubes microspheres from pyrolysis of polypropylene and maleated polypropylene

Microspheres assembled from carbon nanotubes (MCNTs), with the diameters ranging from 5.5 to 7.5 μm, were synthesized by means of pyrolysis of polypropylene and maleated polypropylene in an autoclave. The characterization of structure and morphology was carried out by X-ray diffractometer (XRD), field-emission scanning electron microscopy (FESEM), (high resolution) transmission electron microscope [(HR)TEM)], selected-area electron diffraction (SAED) and Raman spectrum. As a typical morphology, the possible growth process of MCNTs was also investigated and discussed. The results of nitrogen adsorption-desorption indicate that the Brunauer-Emett-Teller (BET) surface area (140.6 m²/g) of the MCNTs obtained at 600 °C is about twice as that (74.5 m²/g) of carbon nanotubes obtained at 700 °C. The results of catalytic experiment show that MCNTs based catalyst has higher catalytic activity than the carbon nanotubes based catalyst for the preparation of methanol and dimethoxy-ethane by oxidation of dimethyl ether.     

Field emission from nonaligned zinc oxide nanowires

Zinc oxide (ZnO) nanowires with an average diameter of 15 nm were grown using a vapor phase transport process. Field emission was achieved from these nanowires in spite of their random orientation. The electric field for the extraction of a 10 μA/cm² current density was measured to range from 4.4 to 5.0 V/μm, and that for a 1 mA/cm² current density from 7.6 to 8.7 V/μm, depending on whether the sample was submitted to a heat treatment. The results exhibit the potential application of ZnO nanowires as field emitters in future flat panel displays.     

Facile synthesis and enhanced photocatalytic activity of hierarchical porous ZnO microspheres

In this paper, hierarchical porous ZnO microspheres were successfully synthesized by calcining the microspheric zinc hydroxide carbonate (ZHC) precursor, which were the precipitate products of a hydrothermal reaction by zinc nitrate hexahydrate and urea in the presence of trisodium citrate. The as-prepared ZnO microspheres with diameters of 4-5 μm were assembled by numerous porous nanosheets which had the uniform thickness of about 10 nm. The photocatalytic activity of the ZnO microspheres was evaluated by photodegradation reaction of methylene blue (MB). The as-prepared ZnO microspheres exhibited a significantly enhanced photocatalytic activity than commercial ZnO and TiO₂. This was mainly attributed to the larger specific surface area and stability against aggregation.     

Fabrication of micrometer-scale spherical titanate nanotube assemblies with high specific surface area

Three-dimensional (3D) micrometer-scale spherical titanate nanotube assemblies have been successfully synthesized via hydrothermal synthesis from Ti powders. The obtained titanate nanotube assemblies have a diameter of around 4-7 µm. The titanate nanotubes have an outer diameter of around 9-10 nm, an inner diameter around 3-4 nm and a length of several micrometers. A proposed two-stage growth mechanism was applied to explain the formation process of these titanate nanotube assemblies. We have also demonstrated that these titanate assemblies have higher specific surface area and larger adsorption capacity than that of titanate nanotubes. And they could possibly be further used in photocatalysts, separation technologies, energy-storage technologies and so on.     

Novel low temperature synthesis of ZnO nanostructures and its efficient field emission property

We have developed a novel, simple and cost effective wet chemical synthetic route for the production of ZnO nanoneedles and nanoflowers at low temperature. The synthesis process does not require any surfactant, template or pre-seeding. The synthesized ZnO nanoneedles have very sharp tips with their lengths in the range 2-3 μm, while for the case of nanoflowers, the nanoneedles were bunched together. X-ray diffraction study and X-ray photoelectron spectroscopic studies confirmed the formation of pure ZnO phase. Studies on the electron field emission property of the grown nanostructures showed that they are very efficient field emitter. The turn-on fields and the threshold fields are 3.6 V/μm, 4.4 V/μm and 5.4 V/μm, 6.8 V/μm for the ZnO nanoneedles and ZnO nanoflowers, respectively. The enhanced field emission property was attributed to the presence of sharp tips of the nanostructures.     

Photo-initiated growth of zinc oxide (ZnO) nanorods

A photo-initiated process via femtosecond pulse-induced heterogeneous nucleation in zinc ammine complex (Zn(NH₃)₄²⁺)-based aqueous solution without catalyst and surfactant, followed by hydrothermal treatments for crystal growth into zinc oxide (ZnO) nanorods, was investigated. Flat-top hexagonal ZnO nanorods with smooth planes of diameter ≥ 100 nm and length ≤ 1 μm were grown with laser irradiation, compared to porous rod-like structures without irradiation. The flat-top planes indicate slow growth rate, due to the intermediate step of Zn(NH₃)₄²⁺ decomposition to Zn(OH)₄²⁻, before dehydration to ZnO. Prolonged hydrothermal treatment produced nanotubes and lateral splits due to OH⁻ erosion of the crystal faces. XRD analysis showed a hexagonal crystal structure while photoluminescence study indicated a peak at about 380 nm.