Combined TiO2/SiO2 mesoporous photocatalysts with location and phase controllable TiO2 nanoparticles

Combined TiO₂/SiO₂ mesoporous materials were prepared by deposition of TiO₂ nanoparticles synthesised via the acid-catalysed sol–gel method. In the first synthesis step a titania solution is prepared, by dissolving titaniumtetraisopropoxide in nitric acid. The influences of the initial titaniumtetraisopropoxide concentration and the temperature of dissolving on the final structural properties were investigated. In the second step of the synthesis, the titania nanoparticles were deposited on a silica support. Here, the influence of the temperature during deposition was studied. The depositions were carried out on two different mesoporous silica supports, SBA-15 and MCF, leading to substantial differences in the catalytic and structural properties. The samples were analysed with N₂-sorption, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and transmission electron microscopy (TEM) to obtain structural information, determining the amount of titania, the crystal phase and the location of the titania particles on the mesoporous material (inside or outside the mesoporous channels). The structural differences of the support strongly determine the location of the nanoparticles and the subsequent photocatalytic activity towards the degradation of rhodamine 6G in aqueous solution under UV irradiation.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Meldola blue immobilized on a new SiO2/TiO2/graphite composite for electrocatalytic oxidation of NADH

Meldola blue immobilized on a new SiO₂/TiO₂/graphite composite was applied in the electrocatalytic oxidation of NADH. The materials were prepared by the sol-gel processing method and characterized by several techniques including scanning electronic microscopy coupled to energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electronic microscopy (HRTEM). Si and Ti mapping profiles on the surface showed a homogeneous distribution of the components. Ti2p binding energy peaks indicate that the formation of Si-O-Ti linkage is presumably the responsible for the high rigidity of the matrices. The good electrical conductivity presented by the composites (5 and 11 S cm⁻¹) can be related to a homogeneous distribution of graphite particles observed by TEM. After the materials characterization, a SiO₂/TiO₂/graphite electrode was prepared and some chemical modifications were performed on its surface to promote the adsorption of meldola blue. The resulting system presented electrocatalytic properties toward the oxidation of NADH, decreasing the oxidation potential to −120 mV. The proposed sensor showed a wide linear response range from 0.018 to 7.29 mmol l⁻¹ and limit of detection of 0.008 mmol l⁻¹. SiO₂/TiO₂/graphite has shown to be a promising material to be used as a suitable support in the construction of new electrochemical sensors.     

Synthesis, characterization and photocatalytic properties of sol-gel TiO2 films

The application of heterogeneous photocatalysis is described as an advanced oxidation process (AOP) for the degradation of the diazo reactive dye using immobilized TiO₂ as a photocatalyst. Starting TiO₂ solutions were prepared with and without the addition of polyethylene glycol (PEG) and TiO₂ films were directly deposited on a borosilicate glass substrate using the sol-gel dip-coating method. The surface morphology and the nanoscale roughness of TiO₂ films were studied by means of atomic force microscopy (AFM). Structural properties of TiO₂ were identified by X-ray diffraction (XRD). The decomposition behaviour of organic compounds from the gels was investigated using thermal gravimetry (TG) and differential scanning calorimetry (DSC). Photocatalytic activities of TiO₂ films in the process of degradation of the commercial diazo textile dye Congo red (CR), used as a model pollutant, were monitored by means of UV/vis spectrophotometry. The kinetics of the degradation of the CR dye was described with the Langmuir-Hinshelwood (L-H) kinetic model.The addition of PEG to the TiO₂ solution resulted in the changes in the film surface morphology, and affected the ratio of anatase-rutile crystal phases and the photocatalytic activity of TiO₂. The TiO₂ film prepared with PEG is characterized by higher roughness parameters (R_a, R_max, R_q, R_z and Z_max), a lower amount of the rutile phase of TiO₂, a higher amount of the anatase phase of TiO₂ and a better photocatalytic activity compared to the TiO₂ film without the addition of PEG.     

Synthesis and electrochemiluminescence of the CeO2/TiO2 composite

CeO₂/TiO₂ composite with kernel–shell structure was synthesized by a sol–gel process. The characterization results show that the composite is made up of anatase phase TiO₂ and cubic system CeO₂. The electrochemiluminescence (ECL) behavior of the CeO₂/TiO₂ composite was studied by a cyclic voltammetry in the presence of persulfate, and the effect factors on ECL emission were discussed. Based on a series of experiments, it is proposed that the strong dual ECL emission produced by the CeO₂/TiO₂ composite resulted from the benefit ECL effect of interface heterojunction in composite.     

Direct formation of H2O2 from H2 and O2 and decomposition/hydrogenation of H2O2 in aqueous acidic reaction medium over halide-containing Pd/SiO2 catalytic system

Formation of H₂O₂ from H₂ and O₂ and decomposition/hydrogenation of H₂O₂ have been studied in aqueous acidic medium over Pd/SiO₂ catalyst in presence of different halide ions (viz. F⁻, Cl⁻ and Br⁻). The halide ions were introduced in the catalytic system via incorporating them in the catalyst or by adding into the reaction medium. The nature of the halide ions present in the catalytic system showed profound influence on the H₂O₂ formation selectivity in the H₂ to H₂O₂ oxidation over the catalyst. The H₂O₂ destruction via catalytic decomposition and by hydrogenation (in presence of hydrogen) was also found to be strongly dependent upon the nature of the halide ions present in the catalytic system. Among the different halides, Br⁻ was found to selectivity promote the conversion of H₂ to H₂O₂ by significantly reducing the H₂O₂ decomposition and hydrogenation over the catalyst. The other halides, on the other hand, showed a negative influence on the H₂O₂ formation by promoting the H₂ combustion to water and/or by increasing the rate of decomposition/hydrogenation of H₂O₂ over the catalyst. An optimum concentration of Br⁻ ions in the reaction medium or in the catalyst was found to be crucial for obtaining the higher H₂O₂ yield in the direct synthesis.     

Photocatalytic properties of a novel layered photocatalyst CsLaSrNb2NiO9

A new visible-light-driven photocatalyst CsLaSrNb₂NiO₉ based on the 2-D layered perovskite crystal structure was prepared by using the solid-state method. Photocatalytic H₂ evolution from the aqueous CH₃OH solution was achieved on the photocatalysts CsLaSrNb₂NiO₉ under UV or visible light irradiation. A possible electronic band structure of CsLaSrNb₂NiO₉ was proposed in regard to the complicated photocatalytic and photophysic properties.     

Enhancement of the photocatalytic performance of Ni-loaded TiO2 photocatalyst under sunlight

A highly sunlight active Ni-loaded TiO₂ nanocomposite (Ni/TiO₂) is successfully prepared by a simple chemical reduction method using tetrabutyl titanate as a precursor, Ni(NO₃)₂·6H₂O as a nickel source, and N₂H₄·H₂O as a reductant, respectively. The crystal structure, morphology and UV–vis diffuse reflectance characteristics are investigated by XRD, TEM, and UV–vis diffuse reflectance spectroscopy, while the photocatalytic performance of Ni/TiO₂ is evaluated by photocatalytic degradation of methyl orange solution under UV and sunlight irradiation. Results show that the crystal structure of TiO₂ is not changed upon the loading of Ni, the photocatalytic performance of TiO₂ under both UV-light and sunlight, however, is enhanced greatly. The enhancement of the photocatalytic performance of Ni/TiO₂ is attributed to the increase of the photogenerated electron–hole separation efficiency and the advanced absorption of light due to surface plasmon effect of Ni nanoparticles.     

Effect of TiO2 particle size on the photocatalytic reduction of CO2

Pure TiO₂ anatase particles with a crystallite diameters ranging from 4.5 to 29 nm were prepared by precipitation and sol–gel method, characterized by X-ray diffraction (XRD), BET surface area measurement, UV–vis and scanning electron microscopy (SEM) and tested in CO₂ photocatalytic reduction. Methane and methanol were the main reduction products. The optimum particle size corresponding to the highest yields of both products was 14 nm. The observed optimum particle size is a result of competing effects of specific surface area, charge–carrier dynamics and light absorption efficiency.     

TiO2 photocatalyst loaded on hydrophobic Si3N4 support for efficient degradation of organics diluted in water

TiO₂ photocatalyst loaded on Si₃N₄ (TiO₂/Si₃N₄) was prepared by a conventional impregnation method and its photocatalytic performance for the degradation of organics (2-propanol) diluted in water was compared with that of TiO₂ photocatalysts (TiO₂/SiO₂, TiO₂/Al₂O₃, and TiO₂/SiC) loaded on various types of supports (SiO₂, Al₂O₃, and SiC). The formation of the well-crystallized anatase phase of TiO₂ was observed on the calcined TiO₂/Si₃N₄ photocatalyst, while a small anatase phase of TiO₂ was observed on the TiO₂/SiC photocatalyst and amorphous TiO₂ species was the main component on the TiO₂/SiO₂ and TiO₂/Al₂O₃ photocatalysts. The measurements of the water adsorption ability of photocatalysts indicated that the TiO₂/Si₃N₄ photocatalyst exhibited more hydrophobic surface properties in comparison to other support photocatalysts. Under UV-light irradiation, the TiO₂/Si₃N₄ photocatalyst decomposed 2-propanol diluted in water into acetone, CO₂, and H₂O, and finally, acetone was also decomposed into CO₂ and H₂O. The TiO₂/Si₃N₄ photocatalyst showed higher photocatalytic activity than TiO₂ photocatalyst loaded on other supports. The well-crystallized TiO₂ phase deposited on Si₃N₄ and the hydrophobic surface of Si₃N₄ support are important factors for the enhancement of photocatalytic activity for the degradation of organic compounds in liquid-phase reactions.     

Morphology control of cathodically deposited TiO2 films

This work demonstrates that the microstructure of TiO₂ film can be designed and controlled by adjusting the temperature and cycle number of cathodic deposition in a solution containing TiCl₃ and NaNO₃. The redox interactions between TiCl₃ and NO₃⁻ are investigated by in situ ultraviolet-visible (UV-vis) absorption spectroscopy. Linear sweep voltammetry (LSV) is employed to study the NO₃⁻ reduction and to clarify the deposition behavior of TiO₂ in the designed plating solution. The decrease in TiO₂ deposition rate with the TiO₂ thickness may be due to the poor electron conductivity of TiO₂ depressing the generation rate of OH⁻ from the NO₃⁻ reduction. The morphology and size of TiO₂ aggregates are strongly influenced by varying the deposition temperature from 5 to 50 °C and a maximal rate of TiO₂ deposition is obtained at 25-35 °C. TiO₂ deposited at 25 °C is the roughest with a roughness factor (Ra) of ca. 67 nm. This study provides a useful method to control the morphology and deposition rate of TiO₂ film for practical photoelectrochemical applications.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

Fabrication of SiO2-ZrO2 composite fiber mats via electrospinning

(1 − x)SiO₂-(x)ZrO₂ (x = 0.1, 0.2) composite fiber mats were prepared by electrospinning their sol-gel precursors of zirconium acetate and tetraethyl orthosilicate (TEOS) without using a polymer binder. The electrospun composite fibers were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR) and mercury porosimetry. The composite fibers having a tetragonal crystalline ZrO₂ were obtained by calcining the electrospun composite fibers at high temperatures. The results show that the structure and crystallization of ZrO₂ in the composite fibers can be controlled by sintering temperature, while the porosity and morphology of the fiber mats did not depend on the sintering temperature.     

TiO2/Na-HZSM-5 nano-composite photocatalyst: Reversible adsorption by acid sites promotes photocatalytic decomposition of methyl orange

TiO₂/Na-HZSM-5 nano-composite photocatalysts were prepared by dispersing TiO₂ onto the external surface of Na⁺-modified nano-ZSM-5 zeolite using a sol–gel process. Samples were characterized by XRF, XPS, HRTEM, XRD, DRUV–vis, NH₃-TPD, FT-IR, and the adsorption and photodegradation of methyl orange (MO) in aqueous solution. Results show the modification of support by Na⁺ does not affect the loading, dispersion and structure of loaded TiO₂, but reduces the acidity of the nano-zeolitic support by preferentially eliminating stronger acid sites. The MO adsorption mainly takes place on the external surface of the supports. The strong and medium strong acid sites of the supports are the adsorption sites. MO molecules adsorbed by strong acid sites are difficult to desorb, whereas the adsorption of MO by medium strong acid sites is reversible. Generally, the MO photodegradation activity of TiO₂/Na-HZSM-5 nano-composites is better than that of bare TiO₂. However, it changes remarkably with the Na⁺ content of the supports, giving the maximum value at 1.1 wt.% Na⁺ when the MO adsorption by the support is almost completely reversible. The enhancement of the photodegradation activity of TiO₂/Na-HZSM-5 nano-composites is attributed to the reversible adsorption of MO by the medium strong acid sites on the nano-zeolitic supports.     

Novel method for preparation of high visible active N-doped TiO2 photocatalyst with its grinding in solvent

This work is focused on improvement on the photo-catalytic activity of a N-doped TiO₂ (reference sample) by its grinding in solvent. Grinding the reference sample in solvent was performed by using a planetary mill at 200 rpm and 15 min grinding time with one of various solvents such as ethanol, ethyl acetate dehydrated (EAD), hexane and water. The ground samples were dried at 80 °C to remove the residual solvents. The prepared sample was characterized by a series of analytical methods including X-ray diffraction (XRD), specific surface area (SSA), particle size, Fourier transform infrared spectroscopy (FT-IR), thermogravimeter mass spectrometer (TG-MS), X-ray photoelectron spectroscopy (XPS), Chemiluminescence as well as the photo-catalytic activity with NO gas decomposition. The prepared sample ground in ethanol showed much improved photocatalytic activity in the wavelength of visible light region, in comparison with the activity of the reference sample. This may be due to the existence of abundant electrons on Ti³⁺/oxygen vacancy sites, which may be generated via current-doubling effect during the dry operation. On the contrary, the sample prepared in EAD showed the worsened photocatalytic activity in visible wavelength region, due to the existence of acetate complex on the surface of the sample as a surface impurity.     

Luminescent properties of a novel afterglow phosphor Sr3Al2O5Cl2:Eu,Ce

A series of Eu²⁺ and Ce³⁺ doped/co-doped Sr₃Al₂O₅Cl₂ afterglow phosphors that presented various bright colors were successfully synthesized via high temperature solid state reaction. The structure and luminescence properties of the obtained samples were characterized by X-ray powder diffraction (XRD), photoluminescence (PL) spectra and decay curves as well as the thermoluminescence (TL) glow curves. The XRD results showed that all the phase could be indexed to the orthorhombic structure with the space group P2₁2₁2₁. After being exposed to a 254 nm or 365 nm mercury lamp, blue/yellow-orange afterglow emissions with broad bands peaking around 620 nm/435 nm, which were ascribed to the characteristic 4f⁶5d–4f⁷/5d¹–4f¹ transitions of Eu²⁺/Ce³⁺, could be observed in phosphors of Sr₃Al₂O₅Cl₂:Eu²⁺/Sr₃Al₂O₅Cl₂:Ce³⁺, respectively. Because of the overlap spectral range between the Sr₃Al₂O₅Cl₂:Eu²⁺ and Sr₃Al₂O₅Cl₂:Ce³⁺ phosphors, the energy transfer (ET) from Ce³⁺ to Eu²⁺ occurred. The related ET process was discussed in detail. Moreover, the incorporation of Ce³⁺ could significantly prolong the afterglow duration of Sr₃Al₂O₅Cl₂:Eu²⁺ phosphor, which was due to the increase of trap concentration. Consequently, 6 h of the afterglow duration could be observed in Sr₃Al₂O₅Cl₂:1.0%Eu²⁺, 0.5%Ce³⁺ sample, exhibiting much longer than that of Sr₃Al₂O₅Cl₂: 1.0%Eu²⁺ (3 h). From the afterglow decay curves and the fitting results, the optimal concentration of Ce³⁺ for the enhanced afterglow property was experimentally determined to be 0.5%.     

Preparation of UO2/TiO2 composite ceramic fuel by sol gel-press forming method

This paper studies the preparation of UO₂/TiO₂ composite ceramic fuel through sol gel-press forming. The research shows that at 1200–1300 °C, UO₂/TiO₂ composite ceramic grains are small, uniform and compact. Among them, UO₂–0.5 wt%TiO₂ has the highest density and good mechanical strength at 1250 °C.     

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.