共查询到20条相似文献,搜索用时 109 毫秒
1.
竖管降膜吸收器布膜装置的设计及实验研究 总被引:2,自引:0,他引:2
针对大型竖管降膜吸收器设计出一种新型的液体布膜装置,以水为介质进行冷模实验及分析,对两种不同结构布膜器进行布膜均匀度的比较,得到装置均匀分布最小喷淋密度为0.05 L/(m·s). 相似文献
2.
3.
4.
5.
降膜蒸发器布膜器的设计 总被引:8,自引:0,他引:8
布膜器是降膜蒸发器的关键部件,它对降膜蒸发器的性能影响是至关重要的。本文介绍了一种布膜器的结构,参数选择及计算方法,并在生产实践中取得了良好的应用效果,对降膜蒸发器的设计是很有益处的。 相似文献
6.
布膜器是降膜蒸发器的关键部件,它对降膜蒸发器的性能影响是至关重要的。本文介绍了一种布膜器的结构、参数选择及计算方法,并在生产实践中取得了良好的应用效果。对降膜蒸发器的设计是很有益处的。 相似文献
7.
竖管降膜吸收反应器是一种高效的吸收反应设备。介绍了该设备的优点、整体结构及关键部件——液体布膜器的设计要求,并详细介绍了目前工业生产中的3种液体布膜器的型式、结构及优缺点。 相似文献
8.
竖管降膜吸收反应器是一种高效的吸收反应设备,介绍了该设备的优点、整体结构及关键部件——液体布膜器的设计要求,详细介绍了目前工业生产中的3种液体布膜器的型式、结构及优缺点。 相似文献
9.
引 言降膜蒸发器是一种高效、节能的蒸发设备 ,具有传热系数高、温差损失小、汽化表面大、物料停留时间短等特点 ,适于热敏性物料蒸发 ,易于实现多效操作 ,广泛应用于化工、轻工、食品加工、海水淡化等领域[1].由降膜蒸发器的工作原理可知 ,降膜蒸发器能否高效运行主要取决于料液在换热管间的均布及其在换热管内壁成膜的均匀程度 .在降膜蒸发器换热管上端安装布膜器是一种有效的方法 .溢流型布膜器结构简单 ,但加工、安装精度要求高 ;目前常用的插件型布膜器成膜较好 ,但结构复杂 ,安装和检修都不方便 ,而且阻力相对来说比较大 .针对这一情… 相似文献
10.
11.
Ritunesh Kumar Digvijay Patil Fu Xiao Piyush Aras 《Chemical Engineering Communications》2017,204(11):1237-1245
Falling film towers are popular in process industries due to moderate air side pressure drop, less energy ingesting liquid distribution and easy cleanup features. Two major limitations of falling film towers are the uneven distribution of liquid across solid surfaces (maldistribution) and contraction of falling liquid film on the solid surface (poor wetting). Maldistribution of liquid is primarily dependent on the type of liquid distributor and scope of liquid flow (slit opening) across solid surfaces. In the current communication; the influence of liquid distributor on maldistribution problem for vertical plate falling film tower has been experimentally investigated. Four types of liquid distributors: plain tube, spray nozzle, perforated plate, and branch tube distributor have been tested. Effect of parameters: slit opening, liquid flow rate, and the number of plates on maldistribution are also explored. It is found that branch tube distributor is best suited for vertical plate falling film tower application. 相似文献
12.
竖管降膜蒸发器多层筛板液体分布装置的研究 总被引:6,自引:0,他引:6
本文介绍了用于竖管降膜蒸发器的多层筛板液体分布器。通过对多层筛板分布器的测定,找出了降流密度与分布不均匀度之间的关系以及粘度对分布不均匀度的影响,提出了在冷模状态下最小降流密度的设计参考值。 相似文献
13.
14.
以一种文丘里型气液分布器为对象,在直径为28 cm的冷模装置中考察了其流体力学性能。气、液流量分别在5~25 m3·h-1、0.2~0.6 m3·h-1范围内,使用激光粒度仪测量了液滴Sauter平均粒径(D32),并测定了其分布均匀性和抗塔板倾斜性能。结果表明:文丘里结构加强了气液混合,与泡罩型分布器相比,此分布器具有更好的液滴破碎性能;气速增大会使出口液体从伞状流变为喷射流,但仍能在直径约为出口直径10倍的区域内均匀分布;在气、液相负荷分别为10~20 m3·h-1、0.4~0.6 m3·h-1时,液位在进液口和进气口之间,此时分布器具有优异的抗塔板倾斜性能。采用计算流体力学软件模拟了分布器内部气液流动过程,得到了相含率和速度矢量图,所得结果有利于分布器的分析与改进。 相似文献
15.
设计了一种底部带有碎流板的新型管式气液分配器。以水和空气代替工业上的原油和氢气进行冷模实验。实验过程为:水由水箱经水泵抽出,经液体流量计计量后进入实验塔上部的气液扩散器,气液两相流经急冷箱冷却后同时向下通过分配器。进入到接液装置的液体通过橡胶管导入到放置在地面上的17个标有编号的量筒中,未进入接液装置的液体流入水箱,气体则排放到大气中。最后用U形管差压计测量分配器的压力降。实验研究了该分配器的分配性能、压力降损失、气液相操作弹性和分布不均度,优化并确定该分配器的结构形式和结构参数。结果表明,该分配器的最佳工作条件为:液相量为0.3m3/h左右,气相量为20~30m3/h。 相似文献
16.
《Powder Technology》2001,114(1-3):186-196
Defluidized zones often appear on the distributor plates of liquid–solid fluidized beds. They can lead to hot spots, the formation of undesirable side products or the degradation of products or reactants. In some cases, a solid residue forms and plugs the distributor.Two different techniques were developed to detect defluidized zones. The first technique uses a specially designed collision probe to monitor local particle motion. The second technique is aimed at the on-line detection of defluidized zones in industrial bioreactors. It uses local bed conductivity fluctuations.Defluidized zones were measured in beds of 3 or 5 mm diameter glass beads fluidized by an aqueous saline solution. Special experiments established the importance of horizontal liquid flow and distributor plate roughness on the formation of defluidized zones.A model describes how a defluidized zone can be eliminated. It considers that a defluidized zone is broken by the drag force on its particles of downward and sideways liquid flow. This liquid flow is induced by suction from the liquid jets issuing from the distributor holes. The resulting drag force is resisted by friction between particles or between particles and the distributor surface. 相似文献
17.
管式降膜蒸发器由于具有传热系数高、传热温差小等优点,已应用于多个工业领域,对管式降膜蒸发器的研究也成为近年来传热技术领域的一项重要课题.文中设计了一套管式降膜蒸发装置,以木质素悬浮液为工质,对影响降膜蒸发传热的因素进行了实验研究,通过冷膜实验测试了所设计的筛板分布器的性能,得出筛板分布器能较好地使物料在换热管内壁上成膜... 相似文献
18.
19.