Transparent conducting F-doped SnO2 thin films grown by pulsed laser deposition

Transparent conducting fluorine-doped tin oxide (SnO₂:F) films have been deposited on glass substrates by pulsed laser deposition. The structural, electrical and optical properties of the SnO₂:F films have been investigated as a function of F-doping level and substrate deposition temperature. The optimum target composition for high conductivity was found to be 10 wt.% SnF₂ + 90 wt.% SnO₂. Under optimized deposition conditions (T_s = 300 °C, and 7.33 Pa of O₂), electrical resistivity of 5 × 10^− 4 Ω-cm, sheet resistance of 12.5 Ω/□, average optical transmittance of 87% in the visible range, and optical band-gap of 4.25 eV were obtained for 400 nm thick SnO₂:F films. Atomic force microscopy measurements for these SnO₂:F films indicated that their root-mean-square surface roughness ( 6 Å) was superior to that of commercially available chemical vapor deposited SnO₂:F films ( 85 Å).     

Combinatorial pulsed laser deposition and thermoelectricity of (La1−xCax)VO3 composition-spread films

La_1−xCa_xVO₃ composition-spread film library was fabricated by combinatorial pulsed laser deposition and their thermoelectric properties were evaluated paralelly by the multi-channel probes of Seebeck coefficient and electric conductivity. Concurrent X-ray analysis verified the formation of solid soluted films in the full composition range (0x1) as judged from the linear variation of the lattice constants. The Seebeck coefficients of La_1−xCa_xVO₃ changed from a large negative value to almost zero with the increase of x, due presumably to the variation of valence in vanadium ions.The power factor in this library was as high as 0.6 μW/cm K², which was obtained at x=0, i.e. pure LaVO₃ grown at 800 °C.     

Microstructure and magnetic properties of zinc ferrite thin films produced by pulsed laser deposition

Zinc ferrite thin films were deposited from a target of zinc ferrite onto a MgO substrate using XeCl excimer laser operating at 308 nm and frequency of 30 Hz. The crystallographic characterizations of the films were performed using X-ray diffraction (XRD). Microstructure, surface morphology, chemical composition and grain size, as well as surface roughness were obtained from scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and atomic force microscopy (AFM). The magnetic properties of the thin films were studied in the temperature range 5–300 K and in fields of up to 5 T using SQUID magnetometry. Data on temperature and field dependence of magnetization provide a strong evidence for superparamagnetism. Paper presented at 8 AGM of MRSI, BARC, Mumbai, 1997.     

Growth and characterization of Bi2Se3 thin films by pulsed laser deposition using alloy target

Bi₂Se₃ thin films were deposited on the (100) oriented Si substrates by pulsed laser deposition technique at different substrate temperatures (room temperature −400 °C). The effects of the substrate temperature on the structural and electrical properties of the Bi₂Se₃ films were studied. The film prepared at room temperature showed a very poor polycrystalline structure with the mainly orthorhombic phase. The crystallinity of the films was improved by heating the substrate during the deposition and the crystal phase of the film changed to the rhombohedral phase as the substrate temperature was higher than 200 °C. The stoichiometry of the films and the chemical state of Bi and Se elements in the films were studied by fitting the Se 3d and the Bi 4d5/2 peaks of the X-ray photoelectron spectra. The hexagonal structure was seen clearly for the film prepared at the substrate temperature of 400 °C. The surface roughness of the film increased as the substrate temperature was increased. The electrical resistivity of the film decreased from 1 × 10⁻³ to 3 × 10⁻⁴ Ω cm as the substrate temperature was increased from room temperature to 400 °C.     

Improved dielectric and ferroelectric properties in Ti-doped BiFeO3-PbTiO3 thin films prepared by pulsed laser deposition

Ti-modified thin films of multiferroic 0.72Bi(Fe_1 − xTi_x)O₃-0.28PbTiO₃ (BFPT, x = 0 and 0.02) solid solution were prepared by pulsed laser deposition. The BFPT (x = 0 and 0.02) films possess a tetragonal structure with highly preferential (001) orientation. The effects of the ionic substitution on the properties of BFPT (x = 0 and 0.02) films have been investigated. The leakage current of the BFPT (x = 0.02) thin film is significantly reduced, and the dielectric and ferroelectric properties greatly improved by the aliovalent ionic substitution of Ti⁴⁺ for Fe³⁺. The BFPT (x = 0.02) thin film exhibits a reasonably high remnant polarization P_r with 2P_r up to 90 μC/cm² at 312 kV/cm and a switchable polarization up to 92 μC/cm² at 417 kV/cm.     

Processing dependence of structural and physical properties of Mg2Ge thin films prepared by pulsed laser deposition

Magnesium germanide (Mg₂Ge) thin films were deposited on MgO (001) substrates using pulsed laser deposition technique. The films were deposited at various substrate temperatures, ranging from 300 to 600 °C. The effects of substrate temperature on structural, electrical and optical properties were studied. All the films, except the samples prepared at 300 °C, were polycrystalline with major diffraction from (200) plane. The highest electrical conductivity of 141.86 Ω^− 1 m^− 1 measured at room temperature was observed for the sample deposited at the highest temperature, with the corresponding charge carrier mobility and concentration of 2.62 cm² V/s and 8.66 × 10¹⁸ cm^− 3, respectively. The carrier concentration dependence of the optical absorption edge energy is accounted for by the Burstein-Moss shift. The variation of strain value may have also contributed to the change in bandgap energy. The reduction in direct bandgap energy was found to vary from 2.20 to 2.00 eV with increasing the deposition temperature.     

Synthesis of SrSnO3 thin films by pulsed laser deposition: Influence of substrate and deposition temperature

SrSnO₃ thin films were prepared by pulsed laser deposition on amorphous silica and single crystal substrates of R-sapphire, (100)LaAlO₃ and (100)SrTiO₃. High quality epitaxial (100) oriented films were obtained on LaAlO₃ and SrTiO₃ while a texture was revealed for films on sapphire deposited at the same deposition temperature of 700 °C. Amorphous films were obtained on silica but a post annealing at 800 °C induced crystallization with a random orientation. The screening of deposition temperature showed epitaxial features on SrTiO₃ from 650 °C while no crystallization was observed at 600 °C. The influence of substrate and deposition temperature was confirmed by Scanning Electron Microscopy and Atomic Force Microscopy observations.     

Structure and microwave dielectric properties of Bi1.5Zn1.0Nb1.5O7 thin films deposited on alumina substrates by pulsed laser deposition

Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films were deposited on polycrystalline alumina substrates by pulsed laser deposition at different substrate temperatures. The phase structure and surface morphology were characterized using X-ray diffractometer (XRD) and atomic force microscopy. Microwave dielectric properties were performed using split-post dielectric resonator method at spot frequencies of 10, 15 and 19 GHz, respectively. The XRD results indicate that the as-deposited Bi_1.5Zn_1.0Nb_1.5O₇ thin films deposited at 650 °C are amorphous in nature. The dielectric permittivity and loss tangent of the amorphous BZN thin films are 75.5 and 0.013 at 10 GHz, respectively. As the measure frequency increased to 19 GHz, the dielectric permittivity slightly decreases and loss tangent slightly increases. BZN thin films were crystallized after the post-annealing by a rapid thermal annealing in air for 30 min. The crystallized BZN thin films exhibit the excellent dielectric properties and frequency responses. The dielectric permittivity and loss tangent of the crystallized BZN thin films are 154 and 0.038 at 10 GHz, respectively.     

Influence of substrate on the pulsed laser deposition growth and microwave behaviour of KTa0.6Nb0.4O3 potassium tantalate niobate ferroelectric thin films

Thin films of potassium tantalate niobate KTa_0.6Nb_0.4O₃ (KTN) were grown by pulsed laser deposition on five different substrates suitable for microwave devices: (100)MgO, (100)LaAlO₃, (1–102)sapphire (R-plane), (0001)sapphire (C-plane) and alumina. The high volatility of potassium at the film growth temperature required the addition of an excess of potassium to the ablation target. For optimized deposition conditions, Rutherford backscattering showed that the KTN films had a 1: 1 atomic ratio for K:(Nb + Ta). As grown KTN thin films were single-phase, without any particular orientation on sintered alumina, whereas an epitaxial growth with the (100) orientation was achieved on (100)MgO and (100)LaAlO₃ with a mosaicity Δω_(100)KTN close to 0.7°–1.5° and  0.4°–0.9°, respectively, attesting a high crystalline quality. In contrast, growth of KTN on R-plane sapphire results in a texture with the (100) orientation and the presence of the (110) orientation as a secondary one. The room temperature measurements carried out on Au interdigited capacitors patterned on KTN coated (100) LaAlO₃ and sapphire led at 1 GHz to an agility ΔC / C  4.6% and  7.2%, respectively, for a moderate applied field of 15 kV cm^− 1. Stubs patterned on the same systems led to an agility ΔF_r / F_r of  2.2% and 4.2%, respectively, for F_r = 7 GHz and the same applied field.     

Composition controlling of KNbO3 thin films prepared by pulsed laser deposition

The composition of KNbO₃ thin films prepared by pulsed laser deposition is crucially influenced by the deposition configuration. In the present study, the composition of KNbO₃ thin films grown on Si (100) substrates by pulsed laser ablation was tried to be controlled by adjusting the target-substrate distance and the oblique angle of substrate from the plume axial direction. It was found that the K deficiency in the films can be effectively avoided by setting the substrate at an appropriate oblique angle from the plume axial direction. The stoichiometric KNbO₃ thin films with a K/Nb molar ratio of 0.98 were successfully obtained, where the substrates were set at an oblique angle of 3-12° from the plume axis while the target-substrate distance was kept at 40 mm.     

Dielectric and structural characterization of KNbO3 ferroelectric thin films epitaxially grown by pulsed laser deposition on Nb doped SrTiO3

KNbO₃ thin films were deposited on SrTiO₃ substrates by pulsed laser deposition. The X-ray diffraction patterns highlight an epitaxial growth according to the (011) orientation. This epitaxial growth was then confirmed by Electron Channeling Pattern. In agreement with the structural characteristics the dense microstructure consists in regular and ordered grains. Dielectric measurements were performed in the 20 Hz to 1 MHz frequency range on a KNbO₃ thin film grown on 2 at.% Nb doped (100)SrTiO₃ substrate in a large range of temperature in order to investigate the paraelectric-ferroelectric transition. Measurements at room temperature revealed a dielectric constant of 450 at 10 kHz and a minimum value of the loss tangent of 0.075 at 100 kHz. Dielectric study in the 20-600 °C temperature range showed a maximum of permittivity at the Curie temperature T_c = 410 °C and evidenced a “progressive” first-order phase transition, different from the classical “diffuse” transition.     

Surface morphology of AlN films synthesized by pulsed laser deposition

Surface morphology of AlN films, synthesized on Si substrates by pulsed laser deposition, has been examined by recording atomic-force-microscopy (AFM) images. The influence of N₂ ambient pressure, ranging from 5 × 10⁻⁴ Pa to 10 Pa, is reflected well in the alteration of the surface roughness and size of crystallites of the AlN films. A tendency of a decrease in the surface roughness with increasing N₂ pressure was observed, which also correlates with the polycrystalline structure of the films. Deposition in vacuum resulted in the highest surface roughness due to the large size of crystallites emerging from the surface, while increasing the nitrogen pressure yielded smaller crystallites and a smoother film surface. The presented results could be useful for applications of pulsed laser deposited AlN in different optical and acoustic devices, where the crystalline quality of the AlN films and the surface is very important.     

Physical properties of CuCrO2 films prepared by pulsed laser deposition

High-quality CuCrO₂ films were prepared by pulsed laser deposition (PLD). The film deposited with the pulse energy density (PED) of 2 mJ/cm² is highly c-axis oriented. The refractive index of the CuCrO₂ films is about 1.29 obtained by transmission spectra of the films, which implies that the CuCrO₂ film will be a potential antireflection coating in visible light. The films prepared with different PEDs show different conduction mechanism, which suggested the different band structure between these CuCrO₂ films.     

Study on TiO2 thin films grown by advanced pulsed laser deposition on ITO

TiO₂ films were grown by an advanced pulsed laser deposition method (PLD) on ITO substrates to be used as functional electrodes in the manufacturing of solar cells. A pure titanium target (99.99%) was irradiated by a Nd:YAG laser (355 and 532 nm, 5 ns, 35 mJ, 3 J/cm²) in an oxygen atmosphere at different pressures (20-160 mTorr) and at room temperature. After deposition, the films were subjected to an annealing process at 350 °C. The film structure, surface morphology, thickness, roughness, and optical transmission were investigated. Regardless of the wavelength used, the films deposited at room temperature presented only Ti₂O and TiO peaks. After thermal treatment, the TiO₂ films became strongly crystalline, with a tetragonal structure and in the anatase phase; the threshold temperature value was 250 °C. The deposition rate was in the range of 0.035-0.250 nm/pulse, and the roughness was 135-305 nm. Optical transmission of the films in the visible range was between 40% and 60%.     

ZnO thin films prepared by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on soda lime glass substrates by pulsed laser deposition (PLD) in an oxygen-reactive atmosphere. The structural, optical, and electrical properties of the as-prepared thin films were studied in dependence of substrate temperature and oxygen pressure. High quality polycrystalline ZnO films with hexagonal wurtzite structure were deposited at substrate temperatures of 100 and 300 °C. The RMS roughness of the deposited oxide films was found to be in the range 2-9 nm and was only slightly dependent on substrate temperature and oxygen pressure. Electrical measurements indicated a decrease of film resistivity with the increase of substrate temperature and the decrease of oxygen pressure. The ZnO films exhibited high transmittance of 90% and their energy band gap and thickness were in the range 3.26-3.30 eV and 256-627 nm, respectively.     

Pulsed laser deposition of La0.67Ca0.33MnO3 thin films on LiNbO3 and surface acoustic wave studies

Surface Acoustic Waves on piezoelectric substrates can be used to investigate the dynamic conductivity of thin films in a non-contact and very sensitive way, especially at low conductivities. Here, we report on such surface acoustic wave studies to characterize thin manganite film like La_0.67Ca_0.33MnO₃, exhibiting a Jan Teller effect with a strong electron phonon interaction and a metal insulator transition at high temperatures.

We report on the deposition of La_0.67Ca_0.33MnO₃ on piezoelectric substrates (LiNbO₃ in different crystal cuts, employing a pulsed laser deposition technique. The structural quality of the thin films are examined by X-Ray Diffraction, Scanning Electron Microscope and Energy Dispersive X-ray spectroscopy. For the electrical characterization, we employ the surface acoustic wave technique, accompanied by conventional direct current resistance measurements for comparison.     

Structural and magnetic properties of Co-Ga co-doped ZnO thin films fabricated by pulsed laser deposition

Co-Ga co-doped ZnO films were fabricated by pulsed laser deposition on quartz substrates. The obtained films exhibited a wurtzite structure with c-axes growth preference. Optical measurements showed the presence of the cobalt ions in a tetrahedral crystal field, which proved that the Co ion substitution in the ZnO lattice, acting as magnetic cation. Hall measurements indicated that the films were n-type conductive with the electron concentrations of ~ 10²⁰/cm³. This value was much higher than that of the Co-doped films, suggesting the effective incorporation of Ga in the films. Room temperature ferromagnetism was observed for the Ga-Co co-doped thin films.     

Magnetism in Si1 − xMnx diluted magnetic semiconductor thin films

We have studied the electrical and magnetic properties of p-type semiconductor thin films of Si_1 − xMn_x/Si (x = 0.036 and 0.05) grown by molecular beam epitaxy. Experimental results reveal that the resistivity of the samples decreases gradually with increasing measurement temperature, which can be described well by Mott's variable-range-hopping model. All the samples exhibit the ferromagnetic ordering above room temperature. Among these samples, Si_0.95Mn_0.05 has a higher hole density and magnetization. This indicates an enhancement of hole-mediated ferromagnetic exchange interactions when the Mn-doping concentration is increased.     

Effect of deposition temperature on morphology and magnetic properties of Co50Fe50 thin films produced by femtosecond pulsed laser deposition

Deposition temperature effect on morphological, topological and magnetic characteristics of nanoparticle-assembled Co₅₀Fe₅₀ films produced by femtosecond pulsed laser deposition (fs-PLD) on Kapton substrate was investigated. For substrate temperature T_s ≥ 550 K, a decrement of the nanoparticle's aggregates and an increment of the nanoparticle's density were observed with respect to room temperature deposition; this in association with a strong increase of the magnetoelastic anisotropy energy lead to a reduction of the remanence ratio, a significant rise of the saturation and coercive fields and an enhancement of the saturation magnetization. The results are discussed focusing on: i) the correlation between films structure and their magnetic behavior; ii) the role of the different anisotropy energies in determining the harder in-plane magnetic behavior for T_s ≥ 550 K. The thermal strain of Kapton substrate holds an important role in generating morphological and topological characteristics of the fs-PLD films and corresponding magnetic properties.     

Luminescence of Cr-doped ZnGa2O4 thin films deposited by pulsed laser ablation

Chromium-doped zinc gallate powder is synthesized via a solid-state reaction and subsequently deposited as a thin film on quartz substrates by using a pulsed laser deposition technique under two different deposition conditions. The films are characterized with X-ray diffraction, scanning electron microscopy, UV-vis spectrophotometry and luminescent measurements. As the oxygen pressure is changed from 0 to 1 Pa, we find that the grain size gets smaller, the crystallinity improves, the band-gap energy increases, the excitation peaks of the charge transfer band exhibit a remarkable blue-shift from 263 to 247 nm and the intensity of the red emission (694 nm) is enhanced. The results suggest that the structural and luminescent properties of ZnGa₂O₄:Cr^3 + thin film phosphors are improved by deposition at an oxygen pressure of 1 Pa.