Overview of Development Status for EAST-NBI System

The neutral beam injection(NBI) system was developed on the Experimental Advanced Superconducting Tokamak(EAST) for plasma heating and current driving. This paper presents the brief history, design, development, and the main experimental results of the RD of neutral beam injector on the test bed and on EAST. In particular, it will describe:(1) how the two beamlines with a total beam power of 8 MW were developed;(2) the design of the EAST-NBI system including the high power ion source, main vacuum chamber, inner components, beam diagnostic system and sub-system;(3) the experimental results of beamline-1 on the summer campaign of EAST in 2014 and,(4) the status of beamline-2 and the future plan of EAST-NBIs.     

Analysis of Power Distribution on Beamline Components at Different Neutralization Efficiencies on NBI Test Stand

Neutral beam injection is recognized as one of the most effective means for plasma heating. According to the research plan of the EAST physics experiment, two sets of neutral beam injector(4–8 MW, 10–100 s) were built and operated in 2014. Neutralization efficiency is one of the important parameters for neutral beam. High neutralization efficiency can not only improve injection power at the same beam energy, but also decrease the power deposited on the heat-load components in the neutral beam injector(NBI). This research explores the power deposition distribution at different neutralization efficiencies on the beamline components of the NBI device. This work has great significance for guiding the operation of EAST-NBI, especially in long pulse and high power operation, which can reduce the risk of thermal damage of the beamline components and extend the working life of the NBI device.     

Long-pulse power-supply system for EAST neutral-beam injectors

The long-pulse power-supply system equipped for the 4 MW beam-power ion source is comprised of three units at ASIPP (Institute of Plasma Physics,Chinese Academy of Sciences):one for the neutralbeam test stand and two for the EAST neutral-beam injectors (NBI-1 and NBI-2,respectively).Each power supply system consists of two low voltage and high current DC power supplies for plasma generation of the ion source,and two high voltage and high current DC power supplies for the accelerator grid system.The operation range of the NB power supply is about 80 percent of the design value,which is the safe and stable operation range.At the neutral-beam test stand,a hydrogen ion beam with a beam pulse of 150 s,beam power of 1.5 MW and beam energy of 50 keV was achieved during the long-pulse testing experiments.The result shows that the power-supply system meets the requirements of the EAST-NBIs fully and lays a basis for achieving plasma heating.     

Performance of a New Ion Source for KSTAR Tokamak Plasma Heating

In the experimental campaign of 2010 and 2011 on KSTAR, the NBI-1 system was equipped with one prototype ion source and operated successfully, providing a neutral beam power of 0.7-1.6 MW to the tokamak plasma. The new ion source planned for the 2012 KSTAR campaign had a much more advanced performance compared with the previous one. The target performance of the new ion source was to provide a neutral deuterium beam of 2 MW to the tokamak plasma. The ion source was newly designed, fabricated, and assembled in 2011. The new ion source was then conditioned up to 64 A/100 keV over a 2-hour beam extraction and performance tested at the NB test stand （NBTS） at the Korea Atomic Energy Research Institute （KAERI） in 2012. The measured optimum perveance at which the beam divergence is a minimum was about 2.5μP, and the minimum beam divergent angle was under 1.0° at 60 keV. These results indicate that the 2.0 MW neutral beam power at 100 keV required for the heating of plasma in KSTAR can be delivered by the installation of the new ion source in the KSTAR NBI-1 system.     

Achievement of 100 s Long Pulse Neutral Beam Extraction in EAST Neutral Beam Injector

Neutral beam injection (NBI) is recognized as one of the most e®ective means for plasma heating. A 100 s long pulse neutral beam with 30 keV beam energy, 10 A beam current and a 100 s long pulse modulating neutral beam with 50 keV beam energy, 16 A beam current were achieved in the EAST neutral beam injector on the test-stand. The preliminary results suggest that EAST-NBI system initially possess the ability of long pulse beam extraction.     

EAST托卡马克的中性束注入方案

高能中性束注入(Neutral beam injection,NBI)是核聚变装置托卡马克采用的芯部辅助加热和非感应电流驱动主要手段之一.本文介绍了国家大科学工程全超导托卡马克实验装置(Experimental advanced super-conductingtokamak,EAST)上的高能NBI加热方案及注入器的工程要求,并讨论了中性束在EAST等离子体中的传输等相关问题.     

EAST强流离子源电源系统的初步测试运行

测试NBI大功率强流离子源的综合测试台正在建设,已研制了离子源等离子体发生器电源系统、等离子体电极高压电源及梯度极分压器、抑制极负高压电源等电源系统,以及高压传输线及缓冲器,在测试台上开展了对EAST中性束注入器第一台兆瓦级强流离子源样机进行整体电源系统测试和离子源起弧放电的初步测试,完成了离子源电源系统初步性能测试及...     

Commissioning of the first KSTAR neutral beam injection system and beam experiments

The neutral beam injection (NBI) system was designed to provide plasma heating and current drive for high performance and long pulse operation of the Korean Superconducting Tokamak Advanced Research (KSTAR) device using two co-current beam injection systems. Each neutral beam injection system was designed to inject three beams using three ion sources and each ion source has been designed to deliver more than 2.0 MW of deuterium neutral beam power for the 100-keV beam energy. Consequently, the final goal of the KSTAR NBI system aims to inject more than 12 MW of deuterium beam power with the two NBI for the long pulse operation of the KSTAR. As an initial step toward the long pulse (～300 s) KSTAR NBI system development, the first neutral beam injection system equipped with one ion source was constructed for the KSTAR 2010 campaign and successfully commissioned. During the KSTAR 2010 campaign, a MW-deuterium neutral beam was successfully injected to the KSTAR plasma with maximum beam energy of 90 keV and the L-H transition was observed with neutral beam heating. In recent 2011 campaign, the beam power of 1.5 MW is injected with the beam energy of 95 keV. With the beam injection, the ion and electron temperatures increased significantly, and increase of the toroidal rotation speed of the plasma was observed as well. This paper describes the design, construction, commissioning results of the first NBI system leading the successful heating experiments carried in the KSTAR 2010 and 2011 campaign and the trial of 300-s long pulse beam extraction.     

Thermal analysis of EAST neutral beam injectors for long-pulse beam operation

Two sets of neutral beam injectors(NBI-1 and NBI-2) have been mounted on the EAST tokamak since 2014. NBI-1 and NBI-2 are co-direction and counter-direction, respectively. As with indepth physics and engineering study of EAST, the ability of long pulse beam injection should be required in the NBI system. For NBIs, the most important and difficult thing that should be overcome is heat removal capacity of heat loaded components for long-pulse beam extraction. In this article, the thermal state of the components of EAST NBI is investigated using water flow calorimetry and thermocouple temperatures. Results show that(1) operation parameters have an obvious influence on the heat deposited on the inner components of the beamline,(2) a suitable operation parameter can decrease the heat loading effectively and obtain longer beam pulse length, and(3) under the cooling water pressure of 0.25 MPa, the predicted maximum beam pulse length will be up to 260 s with 50 keV beam energy by a duty factor of 0.5. The results present that, in this regard, the EAST NBI-1 system has the ability of long-pulse beam injection.     

Performance of upgraded JET neutral beam injectors

The JET neutral beam injection (NBI) system is undergoing an upgrade of both beam power and pulse duration, which will be completed in 2011. In order to obtain an early assessment of the performance of the upgraded injectors, two positive ion neutral injectors (PINIs) with modified ion source and accelerator configuration were installed on Octant 8 Neutral Injector Box and successfully commissioned in summer 2009. Both PINIs were routinely delivering ～2 MW of deuterium neutral beam power during the JET experimental campaign in autumn 2009. These early tests allowed us to predict with confidence that the JET NBI upgrade objective of injecting 34 MW of total deuterium neutral beam power into the JET plasma will be achieved.     

Analysis of MW-scale Beam Extraction of EAST Neutral Beam Injector Test-stand

Neutral beam injection has been recognized as one of the most effective means for plasma heating. The preliminary data of 50 keV, 100 s and 80 keV, 1 s beam extraction have been obtained on the EAST neutral beam injector (NBI) test-stand. In this paper, beam energy distribution deposited on each heat load component and neutral efficiency of EAST-NBI has been measured using water-flow calorimetry and beam divergence angle and perveance have been analyzed according to the data obtained from the thermocouples installed in the calorimeters.     

Evaluation of NBI absorption and fast ion stored energy to improve thermal energy confinement time calculation in EAST

The absorption of neutral beam power and the fast ion stored energy in EAST plasmas with neutral beam injection(NBI)is analyzed to improve the calculation of thermal energy confinement time.The neutral beam power absorption and fast ion stored energy are systematically calculated using the TRANSP code,through the investigation of global parameters including plasma current,line averaged density and beam energy.Results have shown that scaling laws for the NBI absorption coefficient and fast ion energy rate are obtained through statistical analysis.A comparison of the confinement improvement factor H98y2 with these new scaling laws against those assuming fixed coefficients is given.     

Thermodynamic analysis and simulation for gas baffle entrance collimator of EAST-NBI system based on thermo-fluid coupled method

The world's first full Experimental Advanced Superconducting Tokamak(EAST) is designed with the auxiliary heating method of neutral beam injection(NBI)system. Beam collimators are arranged on both sides of the beam channel for absorbing the divergence beam during the beam transmission process in the EAST-NBI system.The gas baffle entrance collimator(GBEC) is a typical high-heat-flux component located at the entrance of gas baffle. An efficient and accurate analysis of its thermodynamic performance is of great significance to explore the working limit and to ensure safe operation of the system under a high-parameter steady-state condition. Based on the thermo-fluid coupled method, thermodynamic analysis and simulation of GBEC is performed to get the working states and corresponding operating limits at different beam extraction conditions. This study provides a theoretical guidance for the next step to achieve long pulse with highpower experimental operation and has an important reference to ensure the safe operation of the system.     

Design of the Prototype Negative Ion Source for Neutral Beam Injector at ASIPP

In order to support the design,manufacture and commissioning of the negativeion-based neutral beam injection(NBI) system for the Chinese Fusion Engineering Test Reactor(CFETR),the Hefei utility negative ion test equipment with RF source(HUNTER) was proposed at ASIPP.A prototype negative ion source will be developed at first.The main bodies of plasma source and accelerator of the prototype negative ion source are similar to that of the ion source for EAST-NBI.But instead of the filament-arc driver,an RF driver is adopted for the prototype negative ion source to fulfill the requirement of long pulse operation.A cesium seeding system and a magnetic filter are added for enhancing the negative ion density near the plasma grid and minimizing co-extracted electrons.Besides,an ITER-like extraction system is applied inside the accelerator,where the negative ion beam is extracted and accelerated up to 50 kV.     

Experimental Results of Ion Beam Extraction of High-Current Ion Source for EAST Neutral Beam Injector

The first campaign of ion beam extraction tests are completed for EAST NBI high current ion source. The hydrogen ion beam with beam voltage of 80 keV is extracted from tetrode accelerator system. During the experiment, the characteristics of arc discharge and ion beam extraction are studied. The arc power reaches 120 kW and the extracted ion beam power reaches 3 MW. The relationship of some key parameters of arc and beam are investigated, and the details are described in this paper.     

Design and Development of a Power Supply System for NBI Test Stand of EAST

A neutral beam injector (NBI) test stand was constructed to develop a multi-megawatt prototype ion source as an auxiliary heating system on experimental advanced superconducting tokamak. A power supply system for the NBI test stand components such as a set of dc power supplies for plasma generator, a dc high voltage power supply of a tetrode accelerator, a transmission line and a surge energy suppressor. Stable arc discharges of the plasma generator with hydrogen gases for 100 s long pulse have been produced by six Langmuir probes feedback loop regulation mode to control the arc power supply. The 4 MW hydrogen ion beam of 1 s is extracted with beam energy of 80 keV and the beam current of 52 A. The dc high voltage power supply for the plasma grid of the prototype ion source was designed to contribute maximum voltage of 100 kV and current of 100 A. The high voltage power output is continuously adjustable to satisfy with plasma physics experiment in operation frequency of 10 Hz. To prevent damage of the beam source at high voltage breakdown, core snubber using deltamax soft magnetic materials have been adopted to satisfy the input energy into the accelerator from the power supply can be reduced to about 5 J in the case of breakdown at 80 kV. For the transmission line, a disc shape multi cable coaxial configuration was adopted and which the dimension of the diameter is 140 mm at the core snubber. The major issues of discharge characteristics with long pulse and beam extraction with high power for the prototype ion source were investigated on the NBI test stand.     

Design of neutral beam injection system for KSTAR tokamak

The neutral beam injection (NBI-1) system has been designed for providing a 300 s deuterium beam of 120 kV/65 A as an auxiliary heating and current drive system of the KSTAR (Korea Superconducting Tokamak Advanced Research) tokamak. The deuterium beam is produced from a long pulse ion source composed of a bucket-type plasma generator and a multi-aperture tetrode accelerator with the help of discharge power supplies and high voltage (HV) power supplies. The beamline components (BLCs) include a neutralizer with an optical multi-channel analyzer (OMA) section, a bending magnet (BM), an ion dump assembly, a movable calorimeter, beam scrapers, and a cryo-sorption pump system in a rectangular vacuum tank. A beam duct equipped with bellows and a voltage break is placed between the NBI vacuum tank and the KSTAR vacuum vessel. All data and parameters of the NBI system are controlled by a control and data acquisition (CODAQ) system through the EPICS based Ethernet interface.     

Numerical Simulation of Non-Inductive Current Driven Scenario in EAST Using Neutral Beam Injection

For achieving the scientific mission of long pulse and high performance operation,experimental advanced superconducting tokamak(EAST) applies fully superconducting magnet technology and is equiped with high power auxiliary heating system.Besides RF(Radio Frequency) wave heating,neutral beam injection(NBI) is an effective heating and current drive method in fusion research.NBCD(Neutral Beam Current Drive) as a viable non-inductive current drive source plays an important role in quasi-steady state operating scenario for tokamak.The non-inductive current driven scenario in EAST only by NBI is predicted using the TSC/NUBEAM code.At the condition of low plasma current and moderate plasma density,neutral beam injection heats the plasma effectively and NBCD plus bootstrap current accounts for a large proportion among the total plasma current for the flattop time.     

Water Flow Calorimetry System of EAST Neutral Beam Injector

Neutral beam injection (NBI) is recognized as one of the most effective means of plasma heating. The EAST NBI water flow calorimetry system (WFCS) based on PCI extensions for instrumentation (PXI) was established, it can measure temperature rise and flow rate of cooling water of the heat load components, and achieve beam power distribution and neutralization efficiency. Experimental data obtained from WFCS are feedback of the ion source operation state and direct the operation parameter optimization of the ion source. Experimental results show that the WFCS is stable, reliable, and meet the experimental requirements fully.     

Analysis of Power Deposition on Heat Load Components for EAST Neutral Beam Injector

Neutral beam injection is recognized as one of the most effective means of plasma heating. The target values of EAST Neutral beam injector (NBI) are beam energy 50–80 keV, injection beam total power 2–4 MW, beam pulse width 10–100 s. The beam power will deposit on the beam collimator due to the beam divergence and it will cause heat damage to heat load components, or even destroy the entire NBI system. In order to decrease the risk, the beam power deposited on heat load components should be assessed. In this article, the percent of power deposition on each heat load components has been calculated using Gaussian beam transmission model. Comparison of the results measured with water flow calorimeter and calculated results shows the beam transmission model has relative good agreement with real distribution. The results can direct the operation parameter optimization of EAST NBI.