Application of a microcoil probe head in NMR analysis of chemicals related to the chemical weapons convention

A 1.7-mm microcoil probe head was tested in the analysis of organophosphorus compounds related to the Chemical Weapons Convention. The microcoil probe head demonstrated a high mass sensitivity in the detection of traces of organophosphorus compounds in samples. Methylphosphonic acid, the common secondary degradation product of sarin, soman, and VX, was detected at level 50 ng (0.52 nmol) from a 30-microL water sample using proton-observed experiments. Direct phosphorus observation of methylphosphonic acid with (31)P{(1)H} NMR experiment was feasible at the 400-ng (4.17 nmol) level. Application of the microcoil probe head in the spiked sample analysis was studied with a test water sample containing 2-10 microg/mL of three organophosphorus compounds. High-quality (1)H NMR, (31)P{(1)H} NMR, 2D (1)H-(31)P fast-HMQC, and 2D TOCSY spectra were obtained in 3 h from the concentrated 1.7-mm NMR sample prepared from 1 mL of the water solution. Furthermore, a 2D (1)H-(13)C fast-HMQC spectrum with sufficient quality was possible to measure in 5 h. The microcoil probe head demonstrated a considerable sensitivity improvement and reduction of measurement times for the NMR spectroscopy in identification of chemicals related to the Chemical Weapons Convention.     

Application of nonselective 1D (1)H-(31)P inverse NMR spectroscopy to the screening of solutions for the presence of organophosphorus compounds related to the chemical weapons convention

1D nonselective (1)H-(31)P HSQMBC, HSQC, and (31)P decoupled HSQC NMR experiments were applied to the screening of original OPCW proficiency test samples for the presence of organophosphorus (OP) compounds related to the Chemical Weapons Convention. The HSQC and HSQMBC spectra are compared to 1D (1)H NMR spectra with WET solvent suppression and (31)P[(1)H] spectra of the same samples. The 1D nonselective HSQC and HSQMBC experiments are shown to be the most sensitive NMR experiments to selectively screen samples for the presence of organophosphorus(OP) compounds. These experiments are at least three times more sensitive than the (31)P[(1)H] NMR experiment and allow the determination of the number of OP compounds present in the sample and their alkyl group bound to the phosphorus atom. Samples spiked at the 5-10 ppm level can be screened within an hour for the presence of OP compounds, whereas for the (31)P[(1)H] experiments, an overnight acquisition is necessary. The sensitivity of the experiments decreases in the order (31)P decoupled HSQC, HSQMBC, and HSQC. For the different alkyl groups, the sensitivity of these experiments decreases in the order methyl approximately isopropyl > ethyl > propyl.     

Membrane-assisted solvent extraction of triazines, organochlorine, and organophosphorus compounds in complex samples combined with large-volume injection-gas chromatography/mass spectrometric detection

The performance of the fully automated membrane-assisted solvent extraction was investigated for 47 environmental contaminants (among them 30 organochlorine compounds, 9 organophosphorus compounds, and 7 triazines). The extraction took place in a 20-mL headspace vial filled with the aqueous sample and containing a polypropylene membrane bag with 1 mL of cyclohexane as extractant. This device was handled by a multipurpose sampler, which enabled the sample to be mixed at a defined temperature with subsequent large-volume injection of the organic extract taken out of the membrane bag. After optimization of extraction parameters, the method was validated for the three compound classes, triazines and organochlorine and organophosphorus compounds, using spiked distilled water. Then, the extraction yield of these analytes from several complex samples such as a natural and a synthetic wastewater, a bacterial culture, and orange juice was determined and compared to a conventional liquid-liquid extraction. Furthermore, the possibility of reducing matrix interference by adding salt, methanol, or detergent during membrane-assisted solvent extraction was investigated.     

Organic–inorganic hybrids obtained by in situ polymerization of aniline in silica/phosphonate matrix

A method for preparing organic–inorganic hybrids containing organophosphorus compounds, silica, and polyaniline (PANI) was developed using sol–gel technique. This method allows the in situ synthesis of organic–inorganic hybrids by reacting tetraethoxysilane (TEOS), aniline, initiator, organophosphorus compound in formic acid. The formic acid has multiple functions: as solvent and acidic media for polymerization of aniline and reagent for sol–gel process. The use of an organophosphorus compound as coupling agent and the introduction of a conductive polymer in silica matrix was investigated.     

Detection of organophosphorus compounds by covalently immobilized organophosphorus hydrolase

As a consequence of organophosphorus (OP) toxins posing a threat to human life globally, organophosphorus hydrolase (OPH) has become the enzyme of choice to detoxify such compounds. Organophosphorus hydrolase was covalently immobilized onto a quartz substrate for utilization in paraoxon detection. The substrate was cleaned and modified prior to chemical attachment. Each modification step was monitored by imaging ellipsometry as the thickness increased with each modification step. The chemically attached OPH was labeled with a fluorescent dye (7-isothiocyanato-4-methylcoumarin) for the detection of paraoxon in aqueous solution, ranging from 10(-9) to 10(-5) M. UV-visible spectra were also acquired for the determination of the hydrolysis product of para-oxon, namely p-nitrophenol.     

Interfacial antiwear and physicochemical properties of alkylborate-dithiophosphates

Boron compounds have become of interest in tribology because of their unique tribochemical and tribological properties. At the same time, dialkyldithiophosphates (DTPs) of transition metals have been extensively used as multifunctional additives in lubricants to control friction and reduce wear in mechanical systems. Because of the environmental pollution and health hazards of these compounds, ashless compounds with reduced amounts of sulfur and phosphorus are desirable. This work reports on the synthesis, characterization, and tribological properties of a new class of compounds, alkylborate-dithiophosphates. This class combines two high-iron-affinity surface active groups, borate and dialkyldithiophosphate, into a single molecule. The final products, viscous liquids, were characterized by FT-IR, multinuclear (1)H, (13)C, (31)P, and (11)B NMR spectroscopy and thermal analyses. Residues of one representative compound from this class, DPB-EDTP, after thermal analyses were additionally characterized by multinuclear (13)C, (31)P and (11)B MAS and (31)P CP/MAS NMR spectroscopy. Solid-state NMR data suggest that a dominant part of the solid residue of DPB-EDTP consists of borophosphates. Antiwear and friction properties of a mineral oil with these novel additives were evaluated in a four-ball tribometer in comparison with O,O'-di-n-butyl-dithiophosphato-zinc(II), Zn-BuDTP, as a reference lubricant additive. The surface morphology and the elemental composition of the tribofilms were characterized using scanning electron microscopy with energy-dispersive X-rays spectroscopy (SEM/EDS). The results show that alkylborate-dithiophosphates, with substantially reduced amounts of sulfur and phosphorus compared with Zn-BuDTP, have considerably better antiwear and friction performance.     

Heteronuclear 19F-1H statistical total correlation spectroscopy as a tool in drug metabolism: study of flucloxacillin biotransformation

We present a novel application of the heteronuclear statistical total correlation spectroscopy (HET-STOCSY) approach utilizing statistical correlation between one-dimensional 19F/1H NMR spectroscopic data sets collected in parallel to study drug metabolism. Parallel one-dimensional (1D) 800 MHz 1H and 753 MHz 19F{1H} spectra (n = 21) were obtained on urine samples collected from volunteers (n = 6) at various intervals up to 24 h after oral dosing with 500 mg of flucloxacillin. A variety of statistical relationships between and within the spectroscopic datasets were explored without significant loss of the typically high 1D spectral resolution, generating 1H-1H STOCSY plots, and novel 19F-1H HET-STOCSY, 19F-19F STOCSY, and 19F-edited 1H-1H STOCSY (X-STOCSY) spectroscopic maps, with a resolution of approximately 0.8 Hz/pt for both nuclei. The efficient statistical editing provided by these methods readily allowed the collection of drug metabolic data and assisted structure elucidation. This approach is of general applicability for studying the metabolism of other fluorine-containing drugs, including important anticancer agents such as 5-fluorouracil and flutamide, and is extendable to any drug metabolism study where there is a spin-active X-nucleus (e.g., 13C, 15N, 31P) label present.     

Effect of the structure of bidentate neutral organophosphorus compounds on the extraction of Sr(II) from aqueous solutions in the presence of ionic liquids

The extraction of microamounts of Sr(II) from aqueous solutions with solutions of bidentate neutral organophosphorus compounds is considerably enhanced in the presence of ionic liquids. The efficiency of the Sr(II) extraction varies in a wide range depending on the nature of the coordinating groups in the extractant molecule, substituents at the P and N atoms, and structure of the fragment linking the coordinating groups.     

流动注射——荧光法测定水样中敌敌畏含量

有机磷农药敌敌畏(DDVP)在过硼酸钠的作用下可将胺类化合物氧化成可发荧光的产物。本研究根据这一原理,建立了定量测定这类农药的流动注射——荧光分光光度法。该方法具有分析速度快、操作方便、重现性好、灵敏度较高等特点。     

Analysis of protein phosphorylation by capillary liquid chromatography coupled to element mass spectrometry with 31P detection and to electrospray mass spectrometry

A method for phosphopeptide identification by capillary liquid chromatography (muLC) interfaced alternatively to element mass spectrometry (inductively coupled plasma mass spectrometry, ICPMS) and to electrospray ionization mass spectrometry (ESI-MS) is described. ICPMS is used for 31P detection and ESI-MS provides the corresponding molecular weight information. Alignment of the two separate muLC runs is performed using the baseline distortion at the elution front, which shows up in both muLC-ICPMS and muLC-ESI-MS. Both a quadrupole and a magnetic sector field mass analyzer were used in combination with ICP. The detection limit achieved for the muLC-ICP-HRMS runs is approximately 0.1 pmol of phosphopeptide injected. Without any further precautions, contamination by phosphate-containing compounds at this level was found to be uncritical. The method is demonstrated for the analysis of a complex mixture of synthetic phosphopeptides and a set of tryptic digests of three phosphoproteins. These include beta-casein, activated human MAP kinase ERK1, and protein kinase A catalytic subunit. The tryptic phosphopeptides of these proteins could all be detected and identified by our new strategy. Analysis of three fractions of protein kinase A catalytic subunit with different phosphorylation status gives direct access to the order in which the phosphorylation of the four phosphorylation sites occurs. The two most important aspects of using muLC-ICPMS with 31P detection for phosphopeptide identification are (i) that a high selectivity is achieved and (ii) that the signal intensity is independent of the chemical form of phosphorus and directly proportional to the molar amount of 31P in the muLC eluate. Thus, muLC-ICPMS with 31P detection is introduced as a new, robust, and specific method in phosphoproteomics.     

Determination of trace amounts of chemical warfare agent degradation products in decontamination solutions with NMR spectroscopy

Decontamination solutions are used for an efficient detoxification of chemical warfare agents (CWAs). As these solutions can be composed of strong alkaline chemicals with hydrolyzing and oxidizing properties, the analysis of CWA degradation products in trace levels from these solutions imposes a challenge for any analytical technique. Here, we present results of application of nuclear magnetic resonance spectroscopy for analysis of trace amounts of CWA degradation products in several untreated decontamination solutions. Degradation products of the nerve agents sarin, soman, and VX were selectively monitored with substantially reduced interference of background signals by 1D 1H-31P heteronuclear single quantum coherence (HSQC) spectrometry. The detection limit of the chemicals was at the low part-per-million level (2-10 microg/mL) in all studied solutions. In addition, the concentration of the degradation products was obtained with sufficient confidence with external standards.     

Acetylcholinesterase-based organophosphate nerve agent sensing photonic crystal

We developed a polymerized crystalline colloidal array (PCCA) photonic crystal sensing material that senses the organophosphorus compound parathion at ultratrace concentrations in aqueous solutions. A periodic array of colloidal particles is embedded in a hydrogel network with a lattice spacing such that it Bragg diffracts visible light. The molecular recognition agent for the sensor is the enzyme acetylcholinesterase (AChE), which binds organophosphorus compounds irreversibly, creating an anionic phosphonyl species. This charged species creates a Donnan potential, which swells the hydrogel network, which increases the embedded particle array lattice spacing and causes a red-shift in the wavelength of light diffracted. The magnitude of the diffraction red-shift is proportional to the amount of bound parathion. These AChE-PCCAs act as dosimeters for parathion since it irreversibly binds. Parathion concentrations as low as 4.26 fM are easily detected.     

Liquid chromatography-tandem mass spectrometry determination of nonionic organophosphorus flame retardants and plasticizers in wastewater samples

A comprehensive method for the determination of nonionic organophosphorus flame retardants/plasticizers in wastewater samples by solid-phase extraction (SPE) with liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) is presented. It allows the determination of 11 organophosphorus compounds, trialkyl and trichloralkyl phosphates, triaryl phosphate, and biphosphates together with triphenylphosphine oxide (TPPO). Limits of quantification after SPE of 100 mL of water are between 3 and 80 ng/L, which are adequate for most aqueous samples. The sensitivity of the LC-ESI-MS approach allows direct injection of aqueous sample without preceding extraction for concentrations in the low microg/L range. The method was finally applied to municipal wastewater samples, showing the occurrence of six phosphoric acid triesters and TPPO in both raw and treated municipal wastewaters.     

Calculations of bond dissociation energies and dipole moments in energetic materials using density-functional methods

We compare the effectiveness of six exchange/correlation functional combinations (Becke/Lee, Yang and Parr; Becke-3/Lee, Yang and Parr; Becke/Perdew-Wang 91; Becke-3/Perdew-Wang 91; Becke/Perdew 86; Becke-3/Perdew 86) for computing C-N, O-O and N-NO2 dissociation energies and dipole moments of five compounds. The studied compounds are hexabydro-1,3,5-trinitro-1,3,5-triazine (RDX), dimethylnitramine, cyanogen, nitromethane and ozone. The Becke-3/Perdew 86 in conjunction with 6-31G** is found to give the best results, although for the dipole moments of RDX, there is a slightly difference that B3P86/6-31G** is less reliable than B3P86/6-31+G**.     

Prediction of substructure and toxicity of pesticides with temperature constrained-cascade correlation network from low-resolution mass spectra.

Artificial neural networks are trained to predict the toxicity or active substructures of organophosphorus pesticides and then are applied to screening GC/MS data for environmentally hazardous compounds. Every mass spectral scan in the chromatographic run is classified, and separate chromatograms are obtained for either toxicity or substructure classes. Classification of mass spectra allows the detection of chromatographic peaks from potentially hazardous compounds that may be missing from the reference database. The neural network models predict substructures and toxicity from mass spectra without first determining the complete configurational structure of the pesticides. Temperature constrained-cascade correlation networks (TCCCN) were used because they are self-configuring networks that train rapidly and robustly. The toxicity classes are defined by the World Health Organization, and the substructure classes are standard organophosphorus pesticide groupings. The TCCCN models are used to mathematically resolve peaks in the chromatograms by substructure and toxicity. Evaluations yielded classification rates of 97 and 84% for substructure and toxicity, respectively.     

Trace level detection of compounds related to the chemical weapons convention by 1H-detected 13C NMR spectroscopy executed with a sensitivity-enhanced, cryogenic probehead

Two-dimensional 1H-13C HSQC (heteronuclear single quantum correlation) and fast-HMQC (heteronuclear multiple quantum correlation) pulse sequences were implemented using a sensitivity-enhanced, cryogenic probehead for detecting compounds relevant to the Chemical Weapons Convention present in complex mixtures. The resulting methods demonstrated exceptional sensitivity for detecting the analytes at trace level concentrations. 1H-13C correlations of target analytes at < or = 25 microg/mL were easily detected in a sample where the 1H solvent signal was approximately 58,000-fold more intense than the analyte 1H signals. The problem of overlapping signals typically observed in conventional 1H spectroscopy was essentially eliminated, while 1H and 13C chemical shift information could be derived quickly and simultaneously from the resulting spectra. The fast-HMQC pulse sequences generated magnitude mode spectra suitable for detailed analysis in approximately 4.5 h and can be used in experiments to efficiently screen a large number of samples. The HSQC pulse sequences, on the other hand, required roughly twice the data acquisition time to produce suitable spectra. These spectra, however, were phase-sensitive, contained considerably more resolution in both dimensions, and proved to be superior for detecting analyte 1H-13C correlations. Furthermore, a HSQC spectrum collected with a multiplicity-edited pulse sequence provided additional structural information valuable for identifying target analytes. The HSQC pulse sequences are ideal for collecting high-quality data sets with overnight acquisitions and logically follow the use of fast-HMQC pulse sequences to rapidly screen samples for potential target analytes. Use of the pulse sequences considerably improves the performance of NMR spectroscopy as a complimentary technique for the screening, identification, and validation of chemical warfare agents and other small-molecule analytes present in complex mixtures and environmental samples.     

Method for determining molar concentrations of metabolites in complex solutions from two-dimensional 1H-13C NMR spectra

One-dimensional (1D) (1)H nuclear magnetic resonance (NMR) spectroscopy is used extensively for high-throughput analysis of metabolites in biological fluids and tissue extracts. Typically, such spectra are treated as multivariate statistical objects rather than as collections of quantifiable metabolites. We report here a two-dimensional (2D) (1)H-(13)C NMR strategy (fast metabolite quantification, FMQ, by NMR) for identifying and quantifying the approximately 40 most abundant metabolites in biological samples. To validate this technique, we prepared mixtures of synthetic compounds and extracts from Arabidopsis thaliana, Saccharomyces cerevisiae, and Medicago sativa. We show that accurate (technical error 2.7%) molar concentrations can be determined in 12 min using our quantitative 2D (1)H-(13)C NMR strategy. In contrast, traditional 1D (1)H NMR analysis resulted in 16.2% technical error under nearly ideal conditions. We propose FMQ by NMR as a practical alternative to 1D (1)H NMR for metabolomics studies in which 50-mg (extract dry weight) samples can be obtained.     

Extraction and sorption preconcentration of U(VI) and Th(IV) from nitric acid solutions using bis(diphenylphosphorylmethylcarbonylamino)alkanes

Extraction of microamounts of U(VI) and Th(IV) from HNO₃ solutions in the form of complexes with polyfunctional neutral organophosphorus compounds, bis(diphenylphosphorylmethylcarbonylamino)alkanes [Ph₂P(O)CH₂C(O)NH]₂(CH₂) _n (n = 3, 5, 8), was studied. The influence of the extractant structure on the efficiency and selectivity of the extraction of U(VI) and Th(IV) was examined, and the stoichiometry of the extractable complexes was determined. The examined compounds exhibit higher extraction ability and selectivity to metal ions in HNO₃ solutions, compared to the alkylamide Ph₂P(O)CH₂C(O)NHC₉H₁₉. The possibility of selective recovery and preconcentration of U(VI) and Th(IV) from nitric acid solutions with a complexing sorbent prepared by noncovalent immobilization of bis(diphenylphosphorylmethylcarbonylamino)pentane on a macroporous polymeric matrix was demonstrated.     

Polydopamine‐Capped Bimetallic AuPt Hydrogels Enable Robust Biosensor for Organophosphorus Pesticide Detection

Noble metal hydrogels/aerogels with macroscopic nanoassemblies characterized by ultralow density, profuse continuous porosity, and extremely large surface area have gained abundant interest due to not only their tunable physicochemical properties, but also promising applications in catalysis and sensing. Coupling the increased reaction temperature with dopamine‐induced effect, herein, a one‐step synthetic approach with accelerated gelation kinetics is reported for the synthesis of polydopamine‐capped bimetallic AuPt hydrogels. 3D porous nanowire networks with surface functionalization of polydopamine make them a promising biocompatible microenvironment for immobilizing acetylcholinesterase (AChE) and constructing enzyme‐based biosensors for sensitive detection of organophosphorus compounds. Taking advantage of their favorable structure and composition, the optimized product exhibits superior electrochemical activity toward thiocholine produced by AChE‐catalyzed hydrolysis of acetylthiocholine. Based on the inhibition of organophosphorus pesticide on the enzymatic activity of AChE, the inhibition mode for the detection of paraoxon‐ethyl is established, displaying linear regions over the range of 0.5–1000 ng L^?1 with a low detection limit of 0.185 ng L^?1.     

Isolation of phosphate solubilizing bacteria and their potential for lead immobilization in soil

Lead (Pb), a highly toxic heavy metal forms stable compounds with phosphate (P). The potential of phosphate solubilizing bacteria (PSB) to immobilize Pb by enhancing solubilization of insoluble P compounds was tested in this research. Eighteen different PSB strains isolated from P amended and Pb contaminated soils were screened for their efficiency in P solubilization. The PSB isolated from P amended soils solubilized 217-479 mg/L of P while the PSB from Pb contaminated soil solubilized 31-293 mg/L of P. Stepwise multiple regression analysis and P solubility kinetics indicated that the major mechanism of P solubilization by PSB is the pH reduction through the release of organic acids. From the isolated bacteria, two PSB were chosen for Pb immobilization and these bacteria were identified as Pantoea sp. and Enterobacter sp., respectively. The PSB significantly increased P solubilization by 25.0% and 49.9% in the case of Pantoea sp., and 63.3% and 88.6% in the case of Enterobacter sp. for 200 and 800 mg/kg of rock phosphate (RP) addition, respectively, thereby enhancing the immobilization of Pb by 8.25-13.7% in the case of Pantoea sp. and 14.7-26.4% in the case of Enterobacter sp. The ability of PSB to solubilize P, promote plant growth, and immobilize Pb can be used for phytostabilization of Pb contaminated soils.