共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
针对济钢现场工艺条件下生产的Ti-IF钢,利用X’Pert ProxX射线衍射宏观织构分析方法,研究了中薄板坯热连轧轧制及随后的冷轧、退火工艺过程中织构的变化规律。IF钢冷硬板主要织构类型为{111}〈110〉、{111}〈112〉和{001}〈110〉,其中{111}〈110〉织构强度达到12;再结晶退火后的IF钢退火板,主要织构类型为{111}〈110〉和{111}〈112〉,{111}〈110〉织构强度提高到15.37。济钢生产的Ti-IF钢获得了对板材成形最有利的{111}//ND织构。 相似文献
3.
在480~750℃条件下,模拟罩式退火,利用光学显微镜、X射线衍射和金相显微硬度计研究了冷轧Ti-IF超深冲钢晶粒结构的变化,通过取向密度函数分析了再结晶过程织构演变规律。研究表明:冷轧Ti-IF超深冲钢的再结晶温度约为630℃,再结晶过程能够在660℃条件下2 h之内完成;冷轧后该钢主要有4种织构,分别是{001}〈110〉、{111}〈110〉、{111}〈112〉和{112}〈110〉;在退火再结晶过程中,{111}逐渐转变为γ-{111},当退火温度升至720℃时,{001}〈110〉和{112}〈110〉转变为纤维织构γ-{111},最终{111}〈110〉和{111}〈112〉成为主要织构类型。 相似文献
4.
以工业生产的热轧板为原料,研究了冷轧压下率对罩式退火后的Ti-IF钢和Ti+Nb-IF钢组织织构和性能的影响。研究结果表明,经罩式退火后,两种IF钢再结晶基本完成,晶粒呈饼状;随着压下率的增加,晶粒尺寸变小;应变硬化指数n90°值逐渐降低。Ti+Nb-IF钢塑性应变比r90°值在碳含量较高、压下率为70%,或碳含量较低、压下率为80%时,达到最大值;Ti-IF钢塑性应变比r90°值在压下率70%时,达到最大值。随着冷轧压下率的加大,IF钢的织构也越强,并且织构从较低冷轧压下率时的{223}〈110〉、{114}〈110〉和{111}织构变为较高压下率时的{223}〈110〉、{111}〈110〉和{114}〈110〉织构,织构类型有向{111}织构靠拢的趋势。 相似文献
5.
冷轧压下率对连续退火Ti-IF钢组织和织构的影响 总被引:1,自引:0,他引:1
以工业生产的Ti-IF钢热轧板为研究材料,结合连续热镀锌线的工艺特点,采用实验室冷轧、盐浴退火方法和金相、X射线织构测试等分析手段,研究了冷轧压下率对组织和织构的影响规律。试验结果表明,随着冷轧压下率从60%提高到90%,冷轧态α取向线上的取向密度不断增强,而且主要形成了{223}110和{114}110织构,γ线上的{111}110和{111}112织构亦有所增强;退火后铁素体晶粒尺寸从9.0级细化到10.5级;试验钢退火后仍具有较强的{223}110和{114}110织构,且随着冷轧压下率的提高,{111}织构有增强的趋势。要获得强的{111}织构,冷轧压下率需在80%以上。 相似文献
6.
《山西冶金》2015,(1)
以铁素体区热轧低温卷取的Ti-IF钢为研究对象,选择13%~75%的冷轧压下率,观察在冷轧过程中织构的演变。研究表明,压下率为46%是一个转折点,冷轧压下率较小(13%~35%)时,表面上取向变化为{110}001→{554}225→{111}112→{111}110→{223}110,{114}110转向{001}110;压下率达到46%时,{111}织构消失;继续增加压下率,{111}织构再次出现,并随压下率增加而增强。随着冷轧压下率的增加,中心面上的{111}织构强度先增加,压下率达到46%后又降低,最强组分先由{001}110向{223}110转动;压下率达46%时,又向反方向转动。 相似文献
7.
以不同热轧卷取温度生产的典型成分Ti-IF钢冷轧硬卷为研究材料,结合改良森吉米尔法连续热镀锌线的工艺特点,采用Gleeble-1500模拟退火方法和金相、x射线织构测试和硬度测试等分析手段,系统研究了退火过程中试验钢组织、再结晶温度和织构的变化.研究结果表明,随着热轧卷取温度的提高,完全再结晶温度降低;在880℃以下,退火温度对铁素体晶粒度影响很小,热轧低温卷取Ti-IF钢的铁素体晶粒度在11.0级以上,热轧高温卷取Ti-IF钢在lO.5级左右,当退火温度提高到920℃时,晶粒明显粗化;试验钢退火后具有较强的{223}<110>和{114}<110>织构,且热轧卷取温度和退火工艺条件对它们影响较小,随着退火温度的升高,试验钢的{111}织构有增强的趋势,特别是当退火温度较高时,退火温度在920℃时,{111}织构明显增强. 相似文献
8.
借助光学显微镜(OM)、X射线衍射(XRD)技术及电子背散射衍射(EBSD)技术,分析了2种含P高强度无间隙原子(IF)钢的热轧组织和热轧、冷轧及退火织构,结果表明:不含B与含B的高强IF钢热轧后,均得到多边形铁素体,但不含B热轧板晶粒尺寸较大。2种钢热轧板织构均比较散漫,γ纤维织构强度较弱,而不含B的IF钢经过80%大变形量冷轧以后,获得强的γ纤维织构,{111}面织构的体积分数达到41.41%,而含B的IF钢冷轧后{111}面织构的体积分数为33.83%。含B的IF钢冷轧后{112}110织构组分的体积分数比不含B的IF钢要高。2种实验钢在810℃退火60~180s以后,{111}面织构强度进一步增强,不含B的IF钢退火120s后{111}面织构的体积分数最大达到72.8%,而含B的IF钢退火120s后{111}面织构的体积分数最大达到66.6%。 相似文献
9.
研究了Ti-IF无间隙原子钢热轧、冷轧、退火(700、800℃)过程的析出行为与织构.该钢在700℃退火过程中形成的FeTiP析出颗粒降低了{111}织构强度,导致r值降低;而800℃退火过程中形成的析出颗粒提高{111}织构强度,强的{111}织构强度增加r值.700℃退火析出物主要为FeTiP,800℃退火析出物主要为Ti4C2S2;由于形成Ti4C2S2析出物,使C在再结晶退火过程中很容易从固溶体中析出而形成{111}织构,促使800 ℃退火时获得良好的成型性. 相似文献
10.
在实验室条件下模拟CSP热轧板为基板生产的低碳冷轧板罩式退火过程,研究再结晶阶段加热速度对冷轧板罩式退火过程组织和织构的影响。结果表明,压下率83.3%的冷轧板,随着再结晶阶段加热速度的增加,会使试样再结晶温度降低,再结晶过程提前完成,{001}110织构变强,{111}110织构先减少后增加,{111}112织构先减少后增加出现峰值,当加热速度超过50℃/h时又减小。在加热速度30~40℃/h间变形织构{112}110有较低的密度值。再结晶阶段加热速度40℃/h的退火工艺成品组织为饼形晶粒,{001}110织构密度较低,{111}110和{111}112密度较强,密度值接近。 相似文献
11.
12.
13.
通过对焦炭在高炉内的历程及其变化规律的剖析,阐述焦炭热性能指标的意义,形象地把焦炭在高炉内的损耗分为三部分(M1,M2,M3)。指出M2对焦比及焦炭价格有一定的指导作用。 相似文献
14.
K Ohta M Nishi M Ueda S Ohyama T Matsubara T Takahashi T Nakajima 《Canadian Metallurgical Quarterly》1998,99(9):589-594
Cancer of the cardia is traditionally discussed with cardiac cancer of the lower portion of the esophagus and upper gastric cancer invading the esophagus, and the specific characteristics of cancer of the cardia have never been clearly defined. We reviewed the outcome of 172 patients with adenocarcinoma of the cardia who had undergone radical surgery between 1949 and 1994 in the Division of Gastrointestinal Surgery of the Cancer Institute Hospital. The centers of the tumors were located within 2 cm above and below the boundary between the esophagus and the stomach, and their longitudinal diameter was less than 8 cm. We divided the patients into an early period (1949-1979; n = 79) and a late period (1980-1994; n = 93), and focused on the historical transition. There were no differences in patient gender or histology between the two periods. However, the late period was associated with fewer cases of esophageal invasion and shorter longitudinal diameter, as the age of the population advanced. The number of advanced cancers such as the localized and infiltrative type had decreased, and early cancer and early clinical stage had become more common, but despite the fact that the number of early cancers had increased, extended dissection, such as thoracic and paraaortic lymph node dissection, was performed more frequently. By clinical stage, the long-term outcome markedly improved in Stage I patient in the late period, and tended to improve in Stage II and III patients. This appears to have been attributable to the prevention of micrometastasis by extended dissection, although the number of early cancers is another major potential cause. There were no differences in the outcome of Stage IV patients between the two periods, and further advances in multimodality therapy must be awaited. The range of resection is basically proximal gastrectomy, and if there are adequate indications, the prognosis is favorable. In view of the status of lymphatic flow and lymph node metastasis, and long-term results, lateroaortic lymph node dissection is important. Since the number of early cancer patients has been increasing, if intraabdominal recurrence is prevented, intrathoracic lymph node dissection will contribute greatly to the outcome of such patients. 相似文献
15.
Some theories of personality hold that an individual's perception of others is influenced by his own personality characteristics; more specifically, that a trait of low social value will be projected more into others, and that insight into the possession of these characteristics reduces this distortion. These 2 hypotheses were tested by having a group of college students rate each other (including themselves) on degree of friendliness or hostility. Agreement with group rating about self yielded the insight score. In general, the hypotheses were supported; the "friendly" Ss were most accurate in their perception of others, and insight was positively associated with accurate perception. From Psyc Abstracts 36:04:4HL16M. (PsycINFO Database Record (c) 2010 APA, all rights reserved) 相似文献
16.
The rates of infection of two methods of external ventricular drainage in use at Atkinson Morley's Hospital--namely, (a) percutaneous drainage with Rickham reservoirs and (b) tunnelled ventriculostomies--were compared in this retrospective review. Percutaneous drainage of CSF with Rickham reservoirs was associated with a 27% rate of infection as identified by positive microbiological cultures; tunnelled ventriculostomy catheters had a 10% infection rate. The difference in the infection rate between the two methods was statistically significant (P < 0.015). Other variables examined, including the age and sex of the patients and the reasons for ventricular drainage, were not associated with an increased rate of infection. Most infections from either method were caused by a coagulase negative staphylococcus. The average duration of ventricular drainage before identification of positive cultures was 5.7 days for Rickham reservoirs and 6.0 days for ventriculostomies. 相似文献
17.
鲁迅先生一生热爱美术作品,对版画中木刻兴趣尤甚.<野草>作为其"写心之作",亦呈现出一些与木刻版画一致的审美特征:一是具有木刻版画的色彩特征,多对比、多冷色,有阴郁的美感;二是具有木刻版画的力度特征,环境描写、人物刻画处处刀锋毕现,遒劲有力,有一种"力之美". 相似文献
18.
针对四辊破碎机车刀架车削中存在的几个问题,详细介绍了电动车刀架的结构和工作原理,建立主要设计参数的数学表达式,并进行适当的分析。改造后,这种电动车刀架运行平稳、可靠、方便、省力,取得了预期的效果。 相似文献
19.
20.
The effect of 20 different antibiotics on chemotaxis by human neutrophils was studied. Human leukocytes incubated with chloramphenicol, rifampin, sodium fusidate, and tetracyclines in vitro showed markedly depressed migration. The mechanisms by which these antibiotics affect leukotaxis are discussed. 相似文献