基于道路摩擦系数估计的智能小车紧急避障策略研究

雾霾环境下驾驶员的视野受到限制,无法准确估计周围的环境信息,对行车安全具有重大影响.自主紧急制动(AEB)系统是一种重要的车辆主动安全功能,用来避免碰撞或减轻碰撞程度.通常,AEB系统利用一个碰撞时间TTC衡量与障碍物发生碰撞的危险程度.通常设计用于制动的TTC门槛值时假设道路摩擦系数为常数,然而,道路情况复杂多变,道路摩擦系数也是变化的,驾驶员在雾霾环境下更难准确估计道路摩擦系数.因此,开发了一个考虑不同摩擦系数对TTC门槛值影响的AEB控制策略.首先用一个复合滑移率轮胎模型来估计峰值道路摩擦系数,再用该系数计算TTC的门槛值,进而利用该Trc门槛值衡量与障碍物发生碰撞的危险程度.因为可以实时识别道路摩擦系数,提出的AEB策略可以自适应雾霾环境下不同的道路表面.仿真结果表明了该方法的有效性.     

Estimation of automotive tire force characteristics using wheel velocity

It is important to estimate friction force characteristics between tire and road in order to improve the control performance of a vehicle in critical motions. In this paper, an estimation method which estimates parameters concerned with a friction force margin is proposed by applying the on-line least-squares method to wheel rotational velocities. The effect of the estimation is evaluated by applying the method to the braking control.     

Estimation of road frictional force and wheel slip for effective antilock braking system (ABS) control

The introduction of electric braking via brake‐by‐wire systems in electric vehicles) has reduced the high transportation delays usually involved in conventional friction braking systems. This has facilitated the design of more efficient and advanced control schemes for antilock braking systems (ABSs). However, accurate estimation of the tire‐road friction coefficient, which cannot be measured directly, is required. This paper presents a review of existing estimation methods, focusing on sliding‐mode techniques, followed by the development of a novel friction estimation technique, which is used to design an efficient ABS control system. This is a novel slip‐based estimation method, which accommodates the coupling between the vehicle dynamics, wheel dynamics, and suspension dynamics in a cascaded structure. A higher‐order sliding‐mode observer–based scheme is designed, considering the nonlinear relationship between friction and slip. A first‐order sliding‐mode observer is also designed based on a purely linear relationship. A key feature of the proposed estimation schemes is the inclusion of road slope and the effective radius of the tire as an estimated state. These parameters impact significantly on the accuracy of slip and friction estimation. The performance of the proposed estimation schemes are validated and benchmarked against a Kalman filter (KF) by a series of simulation tests. It is demonstrated that the sliding‐mode observer paradigm is an important tool in developing the next generation ABS systems for electric vehicles.     

基于轮胎/路面磨擦状况估计的轮胎故障观测器设计

轮胎故障是造成交通事故的主要原因之一.但是目前大多数轮胎故障监测方法由于需 要使用各种复杂的传感器因此制造代价高昂且不可靠.为此,提出了一种新型实用的轮眙故障观 测器.基于考虑外界不确定干扰的新型动态轮胎/路面磨擦模型,该观测器仅仅使用汽车驱动力 及轮胎转速数据,跟踪估计轮胎/路面磨擦系数的变化,并通过对磨擦状况的分析对轮胎状态做 出合理的判断.由于转速传感器是汽车防滑刹车控制系统(ABS)的基本组成部分,因此该观测器 可与ABS结合工作,低成本的实现轮胎故障监测.     

基于补偿神经网络的模糊飞机刹车控制系统研究

尽管飞机防滑刹车可以在保持可操纵性的同时优化刹车效率,但遇到不同路况时刹车性能却时常下降。为了在防滑的同时获得最大的刹车结合系数,该文提出了新的飞机防滑刹车控制律：基于补偿神经网络的模糊控制。控制器识别飞机和机轮的速度反馈,从而调整刹车力矩实现优化刹车。同时系统又可根据复杂的路况,通过补偿神经网络进行自优化。通过MATLAB、VC仿真得出滑移率跟踪曲线。结果表明刹车系统在适应不同路况时有很好的控制性能。     

A fuzzy logic controller for an ABS braking system

Anti-blocking system (ABS) brake controllers pose unique challenges to the designer: a) For optimal performance, the controller must operate at an unstable equilibrium point, b) Depending on road conditions, the maximum braking torque may vary over a wide range, c) The tire slippage measurement signal, crucial for controller performance, is both highly uncertain and noisy, d) On rough roads, the tire slip ratio varies widely and rapidly due to tire bouncing, and e) The braking system contains transportation delays which limit the control system bandwidth. A digital controller design was chosen which combines a fuzzy logic element and a decision logic network. The controller identifies the current road condition and generates a command braking pressure signal, based on current and past readings of the slip ratio and brake pressure. The controller detects wheel blockage immediately and avoids excessive slipping. The ABS system performance is examined on a quarter vehicle model with nonlinear elastic suspension. The parallelity of the fuzzy logic evaluation process ensures rapid computation of the controller output signal, requiring less time and fewer computation steps than controllers with adaptive identification. The robustness of the braking system is investigated on rough roads and in the presence of large measurement noise. This paper describes design criteria, and the decision and rule structure of the control system. The simulation results present the system's performance on various road types and under rapidly changing road conditions     

Non-linear velocity observer for vehicles with tyre–road friction estimation

A non-linear observer is proposed for the estimation of the longitudinal and lateral velocities of automotive vehicles due to highly non-linear friction. To take the unknown time-varying road conditions into account, a real-time tyre–road friction estimation algorithm is provided for adaptation to changes of different road adhesion characteristics. Besides, the coupling effects of the longitudinal and lateral forces are fully exploited to design the non-linear observer based on the longitudinal and lateral acceleration measurements. The observer is computationally efficient and is based on a standard sensor configuration commonly available in modern cars. The uniform global asymptotical stability of the adaptive observer is guaranteed under a certain persistency-of-excitation condition. Moreover, a stronger local stability result can also be obtained, i.e. uniform local exponential stability. The performance of the observer is compared with that of existing approaches under different manoeuvres and road conditions.     

Vehicle sideslip estimation: A kinematic based approach

This paper deals with vehicle sideslip angle estimation. The paper introduces an industrially amenable kinematic-based approach that does not need tire–road friction parameters or other dynamical properties of the vehicle. The convergence of the estimate is improved by the introduction of a heuristic based on readily available inertial measurements. The method is tested on a vast collection of tests performed in different conditions, showing a satisfactory behavior despite not using any information on the road friction. The extensive experimental validation confirms that the estimate is robust to a wide range of driving scenarios.     

Adaptive neuro-fuzzy wheel slip control

Due to complex and nonlinear dynamics of a braking process and complexity in the tire–road interaction, the control of automotive braking systems performance simultaneously with the wheel slip represents a challenging problem. The non-optimal wheel slip level during braking, causing inability to achieve the desired tire–road friction force strongly influences the braking distance. In addition, steerability and maneuverability of the vehicle could be disturbed. In this paper, an active neuro-fuzzy approach has been developed for improving the wheel slip control in the longitudinal direction of the commercial vehicle. The dynamic neural network has been used for prediction and an adaptive control of the brake actuation pressure, during each braking cycle, according to the identified maximum adhesion coefficient between the wheel and road surface. The brake actuation pressure was dynamically adjusted on the level that provides the optimal level of the longitudinal wheel slip vs. the brake pressure selected by driver, the current vehicle speed, the brake interface temperature, vehicle load conditions, and the current value of longitudinal wheel slip. Thus the dynamic neural network model operates (learn, generalize and predict) on-line during each braking cycle, fuzzy logic has been integrated with the neural model as a support to the neural controller control actions in the case when prediction error of the dynamic neural model reached the predefined value. The hybrid control approach presented here provided intelligent dynamic model – based control of the brake actuation pressure in order to keep the longitudinal wheel slip on the optimum level during a braking cycle.     

基于ABS的重型车辆联合制动的特性研究

针对重型车辆利用联合制动方式进行制动时,不能获得最大制动力的问题,将ABS控制与联合制动方式相结合,采用基于Kiencke的μ-s模型,在制动过程中利用带遗忘因子的最小二乘法进行路面识别,通过μ-s的曲线斜率,对路况跃变进行识别,使车辆获得最佳的滑移率,从而获得最大制动力.仿真试验证明:基于ABS的联合制动方式可以获得...     

Nonlinear vehicle side-slip estimation with friction adaptation

A nonlinear observer for estimation of the longitudinal velocity, lateral velocity, and yaw rate of a vehicle, designed for the purpose of vehicle side-slip estimation, is modified and extended in order to work for different road surface conditions. The observer relies on a road-tire friction model and is therefore sensitive to changes in the adhesion characteristics of the road surface. The friction model is parametrized with a single friction parameter, and an update law is designed. The adaptive observer is proven to be uniformly globally asymptotically stable and uniformly locally exponentially stable under a persistency-of-excitation condition and a set of technical assumptions, using results related to Matrosov's theorem. The observer is tested on recorded data from two test vehicles and shows good results on a range of road surfaces.     

Tire lateral force estimation and grip potential identification using Neural Networks,Extended Kalman Filter,and Recursive Least Squares

This paper presents a novel hybrid observer structure to estimate the lateral tire forces and road grip potential without using any tire–road friction model. The observer consists of an Extended Kalman Filter structure, which incorporates the available prior knowledge about the vehicle dynamics, a feedforward Neural Network structure, which is used to estimate the highly nonlinear tire behavior, and a Recursive Least Squares block, which predicts the road grip potential. The proposed observer was evaluated under a wide range of aggressive maneuvers and different road grip conditions using a validated vehicle model, validated tire model, and sensor models in the simulation environment IPG CarMaker ^®. The results confirm its good and robust performance.

     

Application of global sensitivity analysis to a tire model with correlated inputs

When a vehicle equipped with tire is manoeuvred on the ground, the tires are submitted to a number of forces – longitudinal force when driving or braking torque is applied to the wheel and/or lateral force when the wheel is steered to turn at a corner. Pacejka model describes these forces that represent the reaction of the road onto the tire. This nonlinear model depends on correlated parameters such as the friction coefficient, the vertical load, and the cornering stiffness, which have to be identified from some measurements. The sensitivity of Pacejka model to these correlated parameters are studied using an approach based on polynomial chaos. It consists in decorrelating the parameters using the Nataf transformation and then, in expanding the model output onto polynomial chaos. The sensitivity indices are then obtained straightforwardly from the algebraic expression of the coefficients of the polynomial expansion.     

防抱制动系统滑模状态观测和控制系统仿真

该文在考虑不平路面随机激励作用下车辆垂向振动的基础上 ,首先建立了四分之一车辆制动模型 ,而后充分运用滑移模式变结构的分析和设计方法 ,提出了车轮最佳滑移率的滑模实时在线辨识滑模优化算法 ,在对系统可观测性论证的基础上 ,设计了非线性滑模状态观测器 ,给出了单通道防抱制动系统基于滑移率的滑模控制算法 ,通过计算机仿真 ,验证了该控制算法的可行性和有效性 ,为设计具有高鲁棒性的防抱制动系统做了一定的理论探索和仿真工作     

基于小波域的图像噪声估计新方法

提出一种基于小波域区域分割的估计图像噪声的新疗法。该方法利用图像的小波高频系数，在提出图像平滑区域的基础上，准确地估计图像高斯噪声的标准方差、由于考虑了图像的局部信息，因此该方法优于传统的估计方法。用于多幅实验图像的结果表明：在图像受噪声比较小或图像含高频信息较丰富时，该方法比传统疗法更准确。     

基于TruckSim的三轴汽车自寻最优ABS控制设计

为提高三轴汽车的制动安全性能,在TruckSim中建立了三轴整车模型,针对以往研究中自寻最优理论不能应用到整车模型的问题,设计了简单可行的控制逻辑,将该理论应用到三轴整车模型。在TruckSim中建立了对开路面、对接路面、低附着路面、高附着路面四种工况,采用TruckSim与Simulink联合仿真,加入传统逻辑门限ABS作为对比,验证控制器的可行性。仿真结果表明,在四种工况下,自寻最优ABS的制动性能都要优于传统ABS,其中,在低附着路面工况下,自寻最优ABS的优越性最突出,制动距离减少24.5m,制动时间减少2.04s。说明自寻最优ABS可以自动搜索轮胎的最佳滑移率,提高三轴汽车的制动安全性能。     

Vehicle state estimation for anti-lock control with nonlinear observer

Vehicle state estimation during anti-lock braking is considered. A novel nonlinear observer based on a vehicle dynamics model and a simplified Pacejka tire model is introduced in order to provide estimates of longitudinal and lateral vehicle velocities and the tire-road friction coefficient for vehicle safety control systems, specifically anti-lock braking control. The approach differs from previous work on vehicle state estimation in two main respects. The first is the introduction of a switched nonlinear observer in order to deal with the fact that in some driving situations the information provided by the sensor is not sufficient to carry out state estimation (i.e., not all states are observable). This is shown through an observability analysis. The second contribution is the introduction of tire-road friction estimation depending on vehicle longitudinal motion. Stability properties of the observer are analyzed using a Lyapunov function based method. Practical applicability of the proposed nonlinear observer is shown by means of experimental results.     

An intelligent approach to the lateral forces usage in controlling the vehicle yaw rate

A direct yaw moment control system (DYC) is designed to improve the handling and stability of a four‐wheel‐drive electric vehicle. The main task of this paper is to use the lateral forces in the process of optimally controlling vehicle stability. This is performed by defining a variable optimum region for the slip ratio of each wheel. A hierarchical structure is selected to design the control system. The higher‐level control system controls the yaw rate of the vehicle based on the fuzzy logic technique. The lower‐level control system, installed in each wheel, maintains the slip ratio of the same wheel within an optimum region using the fuzzy logic technique. This optimum region for each wheel is continuously modified based on the impact of the lateral force on the generated control yaw moment and the friction coefficient of the road. Therefore, an algorithm for estimation of the friction coefficient is proposed. Computer simulations are carried out to investigate the effectiveness of the proposed method. This is accomplished by comparison of the results of control methods with a fixed slip ratio region and the results of the proposed method with a variable slip ratio region in some maneuvers. The robustness of the proposed controller against hard braking and noise contamination, as well as the effect of steering wheel angle amplitude, is verified. The simulation results show that the influence of the proposed method on enhancing vehicle performance is significant. Copyright © 2010 John Wiley and Sons Asia Pte Ltd and Chinese Automatic Control Society     

Vehicle velocity estimation using nonlinear observers

Nonlinear observers for estimation of lateral and longitudinal velocity of automotive vehicles are proposed. The observers are based on a sensor suite that is standard in many new cars, consisting of acceleration and yaw rate measurements in addition to wheel speed and steering angle measurements. Two approaches are considered: first, a modular approach where the estimated longitudinal velocity is used as input to the observer for lateral velocity, and second, a combined approach where all states are estimated in the same observer. Both approaches use a tire-road friction model, which is assumed to be known. It is also assumed that the road is flat. Stability of the observers is proven in the form of input-to-state stability of the observer error dynamics, under a structural assumption on the friction model. The assumption on the friction model is discussed in detail, and the observers are validated on experimental data from cars.     

考虑非线性因素的飞机防滑刹车系统控制

飞机的刹车过程存在较强的非线性,目前广泛应用的速度差加压力偏调式(PBM)控制律难以实现对飞机刹车的高性能控制.本文提出了一种考虑飞机刹车过程中非线性因素的滑模控制律.首先建立考虑轮胎跑道非线性和刹车盘摩擦系数非线性的的飞机防滑刹车系统非线性模型,然后设计了滑模观测器对飞机速度进行估计,并在此基础上设计了一种滑模变结构控制律,最后基于模糊理论对滑模控制律进行优化,从而抑制控制器的抖振.仿真结果表明,基于模糊指数趋近律的滑模变结构控制律控制效果优于传统“PD+PBM”控制律,抑制控制器输出抖振效果良好,能够很好的适应刹车过程中的复杂非线性因素,刹车效率高,控制方法合理有效.