Isothermal crystallization kinetics and melting behavior of nylon/saponite and nylon/montmorillonite nanocomposites

DSC thermal analysis and X‐ray diffraction have been used to investigate the isothermal crystallization behavior and crystalline structure of nylon 6/clay nanocomposites. Nylon 6/clay has prepared by the intercalation of ε‐caprolactam and then exfoliating the layered silicates by subsequent polymerization. The DSC isothermal results reveal that introducing saponite into the nylon structure causes strongly heterogeneous nucleation induced change of the crystal growth process from a two‐dimensional crystal growth to a three dimensional spherulitic growth. But the crystal growth mechanism of nylon/montmorillonite nanocomposites is a mixed two‐dimensional and three‐dimensional spherulitic growth. The activation energy drastically decreases with the presence of 2.5 wt % clay in nylon/clay nanocomposites and then slightly increases with increasing clay content. The result indicates that the addition of clay into nylon induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). The correlation among crystallization kinetics, melting behavior, and crystalline structure of nylon/clay nanocomposites is also discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2196–2204, 2004     

Studies on nylon 6/clay nanocomposites by melt‐intercalation process

The preparation of nylon 6/clay nanocomposites by a melt‐intercalation process is proposed. X‐ray diffraction and DSC results show that the crystal structure and crystallization behaviors of the nanocomposites are different from those of nylon 6. Mechanical and thermal testing shows that the properties of the nanocomposites are superior to nylon 6 in terms of the heat‐distortion temperature, strength, and modulus without sacrificing their impact strength. This is due to the nanoscale effects and the strong interaction between the nylon 6 matrix and the clay interface, as revealed by X‐ray diffraction, transmission electron microscopy, and Molau testing. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1133–1138, 1999     

Synthesis and characterization of nylon 6/clay nanocomposites prepared by ultrasonication and in situ polymerization

Nylon 6 nanocomposites were prepared by the in situ polymerization of ε‐caprolactam with ultrasonically dispersed organically modified montmorillonite clay (Cloisite 30B®). Dispersions of the clay platelets with concentrations in the range 1–5 wt % in the monomer were characterized using rheological measurements. All mixtures exhibited shear‐thinning, signifying that the clay particles were dispersed as platelets and forming a “house of cards” structure. Samples with Cloisite concentrations above 2 wt % showed a drop in viscosity between the initial shearing and repeated shearing, indicative of shearing breaking down the initial “house of cards” structures formed on sonication. DMTA measurements of the samples showed an increase in the β‐relaxation temperature with increasing clay concentration. The bending modulus, at temperatures below T_g, showed an increase with increasing clay concentration up to 4 wt %. X‐ray diffraction measurements showed that all nylon 6/Cloisite 30B samples were exfoliated apart from the 5 wt %, which showed that some intercalated material was present. The nylon crystallized into the α‐crystalline phase, which is the most thermodynamically stable form. Preference for this form may be a consequence of the long time associated with the postcondensation step in the synthesis or the influence of the platelets on the nucleation step of the crystal growth. DSC measurements showed a retardation of the crystallization rate of nanocomposite samples when compared with that of pure nylon 6, due to the exfoliated clay platelets hindering chain movement. This behavior is different from that observed for the melt‐mixed nylon 6/clay nanocomposites, which show an enhancement in the crystallization rate. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystalline forms in melt‐crystallized syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and polarized optical microscopy have been used to investigate the structural change of syndiotactic polystyrene/clay nanocomposites. The nanocomposite has prepared by mixing an sPS polymer solution with organically modified montmorillonite. Both X‐ray diffraction and transmission electron microscopy results indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into the sPS matrix. The X‐ray diffraction data also show the presence of polymorphism in sPS/clay nanocomposites, which is strongly dependent on the thermal history of the nanocomposites from the melt and on the content of clay. In this study, the effect of premelting temperatures and crystallization temperatures of sPS and sPS/clay nanocomposites on their crystalline phases is discussed.     

Crystallization behavior of nylon 6 nanocomposites

The crystallization behavior of nylon 6 nanocomposites formed by melt processing was investigated. Nanocomposites were produced by extruding mixtures of organically modified montmorillonite and molten nylon 6 using a twin screw extruder. Isothermal and non-isothermal crystallization studies involving differential scanning calorimetry (DSC) were conducted on samples to understand how organoclay concentration and degree of clay platelet exfoliation influence the kinetics of polyamide crystallization. Very low levels of clay result in dramatic increases in crystallization kinetics relative to extruded pure polyamide. However, increasing the concentration of clay beyond these levels retards the rate of crystallization. For the pure nylon 6, the rate of crystallization decreases with increasing the molecular weight as expected; however, the largest enhancement in crystallization rate was observed for nanocomposites based on high molecular weight polyamides; this is believed to stem from a higher degree of platelet exfoliation in these nanocomposites. Wide angle X-ray diffraction (WAXD) and DSC were further used to characterize the polymer crystalline morphology of injection molded nanocomposites. The outer or skin layer of molded specimens was found to contain only γ-crystals; whereas, the central or core region contains both the α and γ-forms. The presence of clay enhanced the γ-structure in the skin; however, the clay has little effect on crystal structure in the core. Interestingly, higher levels of crystallinity were observed in the skin than in the core for the nanocomposites, while the opposite was true for the pure polyamides. In general, increasing the polymer matrix molecular weight resulted in a lower degree of crystallinity in molded samples as might be expected.     

Effect of clay addition on the morphology and thermal behavior of polyamide 6

The nanostructure, morphology, and thermal properties of polyamide 6 (PA6)/clay nanocomposites were studied with X‐ray scattering, differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The wide‐angle X‐ray diffraction (WAXD) and TEM results indicate that the nanoclay platelets were exfoliated throughout the PA6 matrix. The crystallization behavior of PA6 was significantly influenced by the addition of clay to the polymer matrix. A clay‐induced crystal transformation from the α phase to the γ phase for PA6 was confirmed by WAXD and DSC; that is, the formation of γ‐form crystals was strongly enhanced by the presence of clay. With various clay concentrations, the degree of crystallinity and crystalline morphology (e.g., spherulite size, lamellar thickness, and long period) of PA6 and the nanocomposites changed dramatically, as evidenced by TEM and small‐angle X‐ray scattering results. The thermal behavior of the nanocomposites was investigated with DSC and compared with that of neat PA6. The possible origins of a new clay‐induced endothermic peak at high temperature are discussed, and a model is proposed to explain the complex melting behavior of the PA6/clay nanocomposites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1191–1199, 2007     

Isothermal and nonisothermal crystallization kinetics of syndiotactic polystyrene/clay nanocomposites

Differential scanning calorimeter (DSC) and X‐ray diffraction methods were used to investigate the isothermal and nonisothermal crystallization behavior and crystalline structure of syndiotactic polystyrene (sPS)/clay nanocomposites. The sPS/clay nanocomposites were prepared by mixing the sPS polymer solution with the organically modified montmorillonite. DSC isothermal results revealed that introducing 5 wt% of clay into the sPS structure causes strongly heterogeneous nucleation, inducing a change of the crystal growth process from mixed three‐dimensional and two‐dimensional crystal growth to two‐dimensional spherulitic growth. The activation energy of sPS drastically decreases with the presence of 0.5 wt% clay and then increases with increasing clay content. The result indicates that the addition of clay into sPS induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). We studied the non‐isothermal melt‐crystallization kinetics and melting behavior of sPS/clay nanocomposites at various cooling rates. The correlation among crystallization kinetics, melting behavior and crystalline structure of sPS/clay nanocomposites is discussed. Polym. Eng. Sci. 44:2288–2297, 2004. © 2004 Society of Plastics Engineers.     

Structure and thermal behaviour of nylon 6 nanocomposites

In this article, nylon 6/clay nanocomposites with 5 wt % clay (NCN5) were prepared by a twin screw extruder. The effects of annealing including solid‐state annealing (170 and 190°C) and melt‐state annealing (240°C) on the polymorphic behavior and thermal property of NCN5 and nylon 6 have been comparatively studied as a function of annealing time using modified differential scanning calorimetry (MDSC) and wide‐angle X‐ray diffraction. It was demonstrated that NCN5 and nylon 6 exhibit a similar polymorphic behavior when they were annealed at 190°C for different time durations. As the annealing temperature was elevated to 240°C, significant differences in thermal behavior and polymorphism between NCN5 and nylon 6 could be found. For example, the α crystal became the absolutely dominating crystalline phase for NCN5 sample independent on the annealing durations, whereas the formation of γ crystal is greatly enhanced in neat nylon 6 with increasing annealing time. Moreover, a small endothermic peak is observed around 180°C in both nylon 6 and NCN5 samples annealed at 170 and 190°C, which might be related to the melting of microcrystals formed in the amorphous regions during annealing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3116–3122, 2006     

Morphology and crystallization behavior of nylon 6‐clay/neat nylon 6 bicomponent nanocomposite fibers

Nylon 6‐clay hybrid/neat nylon 6, sheath/core bicomponent nanocomposite fibers containing 4 wt % of clay in sheath section, were melt spun at different take‐up speeds. Their molecular orientation and crystalline structure were compared to those of neat nylon 6 fibers. Moreover, the morphology of the bicomponent fibers and dispersion of clay within the fibers were analyzed using scanning electron microscopy and transmission electron microscopy (TEM), respectively. Birefringence measurements showed that the orientation development in sheath part was reasonably high while core part showed negligibly low birefringence. Results of differential scanning calorimetry showed that crystallinity of bicomponent fibers was lower than that of neat nylon 6 fibers. The peaks of γ‐crystalline form were observed in the wide‐angle X‐ray diffraction of bicomponent and neat nylon 6 fibers in the whole take‐up speed, while α‐crystalline form started to appear at high speeds in bicomponent fibers. TEM micrographs revealed that the clay platelets were individually and evenly dispersed in the nylon 6 matrix. The neat nylon 6 fibers had a smooth surface while striped pattern was observed on the surface of bicomponent fibers containing clay. This was speculated to be due to thermal shrinkage of the core part after solidification of the sheath part in the spin‐line. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39996.     

Investigation on Unusual Crystallization Behavior in Polyamide 6/Montmorillonite Nanocomposites

The crystallization behavior and crystal structure of polyamide 6/montmorillonite (PA6/MMT) nanocomposites were investigated by differential scanning calorimetry and X‐ray diffraction, and an interesting behavior was observed. The material was prepared via melt compounding using an organophilic clay obtained by co‐intercalation of epoxy resin and quaternary ammonium into Na‐montmorillonite. A maximum in degree of crystallinity was obtained at 5 wt.‐% MMT and the reasons for this, based on the MMT layer distribution, were discussed. The degree of crystallinity showed a strong dependence on the cooling rates. In contrast with typical behavior, a higher cooling rate resulted in a higher degree of crystallinity. In nanocomposites, the γ‐crystalline phase was dominant.     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

Preparation and characterization of nylon 6/organoclay nanocomposite filament fibers

A series of nylon 6 (NY6)/organoclay nanocomposites were prepared via in situ polymerization of ε‐caprolactam in the presence of 1,2‐aminododecanoic acid‐intercalated montmorillonite (ADA‐MMT) organoclay (1–5 wt%) using 6‐aminocaproic acid as polymerization catalyst. The extent of organoclay dispersion in NY6 matrix was analyzed using WAXD and SEM measurements. DSC studies revealed marginal shift in melting and melt‐crystallization peaks toward lower temperature with increasing clay content. Melt viscosity studies for NY6/ADA‐MMT exhibited higher shear‐thinning behavior than neat NY6 probably due to the slip between NY6 matrix and exfoliated organoclay platelets during shear flow. The prepared nanocomposites were melt‐spun and studied for their property improvements against varying clay content, draw ratios, and annealing conditions. Birefringence and sonic velocity values increased initially at lower draw ratios (≤2.5) due to increased orientation of molecular chains along the drawing direction but saturated at higher draw ratio (3.0) for all the samples. At the same draw ratio; compared to neat NY6, NY6/organoclay fibers showed increased chain orientation along the drawing direction which can be attributed to the “tethering effect” of organoclay on NY6 matrix. The initial modulus and stress at break were sensitive to factors such as draw ratio, clay content, and annealing conditions. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

The role of crystallinity and reinforcement in the mechanical behavior of polyamide‐6/clay nanocomposites

The mechanical behavior of compression‐molded polyamide‐6 (PA6) reinforced with 2 wt% of organo‐nanoclay (montmorillonite intercalated with ω‐amino dodecanoic acid) has been studied and compared to that of PA6. The tensile strength and the Young's modulus of the PA6/clay were 15% higher than those of PA6. Differential scanning calorimetry, Fourier transform infrared spectroscopy, and X‐ray diffraction showed that the crystalline structures of PA6 and PA6/clay differed considerably. A crystallinity of 25% with a dual structure composed of the γ and α forms was obtained in PA6/clay, while a crystallinity of 31% with the α form as the dominant crystalline structure was obtained in PA6. To understand the role of the crystalline structure of PA6, the molding process was modified to obtain PA6 specimens with different levels of crystallinity and different crystalline forms. Quenching molten PA6 at a cooling rate sufficiently high to prevent crystallization gave a material that was predominantly amorphous (crystallinity of 7%) with traces of the mesomorphic β or γ* form. Annealing this material at 80°C considerably increased crystallinity to 21%, which was also of the mesomorphic β or γ* form. PA6 with a predominant crystalline γ form could not be generated. Comparisons with PA6/clay in terms of crystallinity and mechanical behavior lead to the conclusion that the improvements in rigidity and strength observed when montmorillonite is added to PA6 are related to the reinforcing filler and not to a modification of the crystalline structure.     

Crystallization behavior of nylon 11/montmorillonite nanocomposites under annealing

Exfoliated nylon 11/montmorillonite (MMT) nanocomposites were prepared via in situ polymerization by the dispersion of organically modified MMT in 11‐aminoundecanoic acid monomer. The polymorphic behavior of the nylon 11/MMT nanocomposites was investigated with X‐ray diffraction, transmission electron microscopy, and Fourier transform infrared with attenuated total reflectance. MMT induced and stabilized the δ‐crystalline form of nylon 11. The crystal structure of nylon 11 was transformed from a hexagonal δ‐form structure to a triclinic α‐form structure during the annealing process. Meanwhile, the hydrogen bonds in the nanocomposites also exhibited some differences from neat nylon 11 after annealing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5483–5489, 2006     

Modifying montmorillonite clay via silane grafting and interfacial polycondensation for melt compounding of nylon‐66 nanocomposite

A trifunctional organo alkoxysilane (3‐aminopropyl)triethoxysilane (γ‐APS) has been used as reagent for the chemical modification of montmorillonite clay. Silane grafting was taken place in dry and hydrolyzing conditions. Silane grafted and pristine clay took part in interfacial polycondensation process to deposit a layer of nylon‐66 onto the clay lamellae and therefore, enhance their affinity with nylon‐66 matrix. Evidence of presence of grafted silane molecules and deposition of nylon‐66 on clay particles were provided by Fourier transform‐infrared, thermogravimetric analysis (TGA), and X‐ray diffraction (XRD). Such modified clays and pristine clays were melt compounded with nylon‐66. The structures of the resulting nylon composites were characterized using XRD and transmission electron microscopy and the results showed presence of both intercalation and exfoliation. TGA thermograms of nanocomposites indicated improved thermal stability upon the incorporation of silane grafted montmorillonite. Furthermore, differential scanning calorimetry scans showed that silane modified clays promoted crystallization in nanocomposites. Increase of storage modulus and depression of tan δ peak in nanocomposites in dynamical mechanical thermal analysis were observed. The rheological properties of nylon‐66 and nanocomposites were also evaluated and differences in values of complex viscosity of samples were noticed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Abrasion studies of nylon 6/montmorillonite nanocomposites using scanning electron microscopy,fourier transform infrared spectroscopy,and X‐ray photoelectron spectroscopy

In this article, abrasion performance of commercial nylon 6 and nylon 6/montmorillonite (MMT) nanocomposites was studied. The polymer nanocomposites showed poor abrasion resistance compared to the neat polymer. The wear loss increased linearly with clay concentration. Changes in surface morphology, composition, and structure were investigated by scanning electron microscopy (SEM), Fourier transform infrared (FTIR)‐attenuated total reflection spectroscopy, and X‐ray photoelectron spectroscopy (XPS). SEM images showed that all the abraded surfaces contained fractured particles. However, the abraded nanocomposite surfaces had much deeper grooves compared to the homopolymer. FTIR results showed an increase in the amount of α crystals and a decrease in the amount of γ crystals on all the surfaces after abrasion. This was attributed to the strain‐induced γ to α crystal transformation. The largest amount of α crystals was formed in the abraded surface of pure nylon 6, and the amount of α crystals formed decreased with increasing MMT content. XPS results showed an increase in the [Si]/[N] elemental ratio for all nanocomposites after abrasion, indicating an increase in the clay content of the surface. Abrasive wear mechanism is as follows: (1) tensile tearing is the dominant wear mechanism for all the samples; (2) the cutting mechanism becomes more important when MMT content increases; (3) the polymer matrix is easier to be removed than clay during the abrasion process; (4) in nylon 6/MMT systems, the poor abrasion resistance is attributed to defects at the clay‐polymer interface, resulting in greater wear of the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

尼龙6/粘土纳米复合材料的性能

对尼龙6/粘土纳米复合材料(PA6CN)的力学性能、结晶性能、流变性能、热稳定性、阻隔性能、阻燃性能、各向异性和可纺性进行了综述。加入粘土后,基体尼龙6的晶型变为γ型,改善了尼龙6的力学性能,提高了热变形温度,降低了吸水率,改善了气体阻隔性和材料的阻燃性,拓宽了复合材料的应用范围。     

High temperature behaviour of the crystalline phases in unfilled and clay-filled nylon 6 fibers

Temperature-induced crystalline phase transitions in neat nylon 6 fibers as well as nylon 6/montmorillonite nanocomposite fibers have been studied by means of wide-angle X-ray scattering. Both types of melt spun fibers only consist of the γ crystalline phase that does not display any transition during heating up to the melt. In contrast, fibers drawn up to the maximum draw ratio at 140 °C display the single α phase with a high degree of chain orientation. During the temperature increase, the α phase undergoes a gradual structural disordering but preserves its monoclinic character up to melting. The structural evolution of the α form turned out sensitive to the thermal and mechanical treatment of the fibers. Annealing the unfilled drawn fibers at 150 °C prior to the WAXS experiment improves the thermal stability of the α form due to healing of the processing-induced crystalline defects. The montmorillonite-filled fibers display both the α and the γ crystals, which readily turn into α crystal form only upon drawing. Due to the matrix shearing between the MMT platelets, the H-bonded sheets display a higher thermal stability as compared with unfilled drawn fibers. Upon cooling from the melt, the first signs of crystallization are of γ form in the MMT-PA6 fibers, but the α form rapidly turns predominant. Crystallization kinetics considerations are put forward to account for this finding.     

Thermal,mechanical, and barrier properties of polyethylene/surlyn/organoclay nanocomposites blown films prepared by different mixing methods

(Low‐density polyethylene) (LDPE)/clay nanocomposites were prepared by melt blending in a twin‐screw extruder by using different mixing methods. Zinc‐neutralized carboxylate ionomer was used as a compatibilizer. Blown films of the nanocomposites were then prepared. The effect of mixing method on the clay dispersion and properties of the nanocomposites was evaluated by wide‐angle X‐ray diffraction analysis, mechanical properties, thermal properties, and barrier properties. The structure and properties of nanocomposites containing different amounts of nanoclay prepared by selected mixing techniques were also investigated. It was found that melt compounding of Surlyn/clay masterbatch with pure LDPE and Surlyn (two‐step‐a method) results in better dispersion and intercalation of the nanofillers than melt mixing of LDPE/Surlyn/clay masterbatch with pure LDPE and surlyn (two‐step‐b method) and direct mixing of LDPE with clay. The films containing ionomer have good barrier properties. A wide‐angle X‐ray diffraction pattern indicates that intercalation of polymer chains into the clay galleries decreases by increasing the clay content. Barrier properties and tensile modulus of the films were improved by increasing the clay content. In addition, tensile strength increased in the machine direction, but it decreased in the transverse direction by increasing the clay content. DSC results showed that increasing the clay content does not show significant change in the melting and crystallization temperatures. The results of thermogravimetric analysis showed that the thermal stability of the nanocomposites decreased by increasing the clay content more than 1 wt%. J. VINYL ADDIT. TECHNOL., 21:60–69, 2015. © 2014 Society of Plastics Engineers     

Influence of clay content on the melting behavior and crystal structure of nonisothermal crystallized poly(L‐lactic acid)/nanocomposites

To study the effect of organophilic clay concentration on nonisothermal crystallization, poly(L ‐lactic acid) (PLLA)/montmorillonite (MMT) nanocomposites were prepared by mixing various amounts of commercial MMT (Cloisite^® 30B) and PLLA. The effect of MMT content on melting behavior and crystal structure of nonisothermal crystallized PLLA/MMT nanocomposites was investigated by differential scanning calorimetry (DSC), small‐angle X‐ray scattering, and wide‐angle X‐ray diffraction (XRD) analyses. The study was focused on the effect of the filler concentration on thermal and structural properties of the nonisothermally crystallized nanocomposite PLLA/MMT. The results obtained have shown that at filler loadings higher than 3 wt %, intercalation of the clay is observed. At lower clay concentrations (1–3 wt %), exfoliation predominates. DSC and XRD analysis data show that the crystallinity of PLLA/MMT composites increases drastically at high clay loadings (5–9 wt %). In these nanocomposites, PLLA crystallizes nonisothermally in an orthorhombic crystal structure, assigned to the α form of PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012