Synthesis and material properties of syndiotactic polystyrene/organophilic clay nanocomposites

Syndiotactic polystyrene (sPS)/organophilic clay nanocomposites were fabricated by direct‐melt intercalation method. To overcome the thermal instability of organophilic clay at high‐melt processing temperatures of sPS, an organophilic clay modified by alkyl phosphonium was adopted, which is known to be thermally stable. By using the newly synthesized clay, we could fabricate sPS intercalated nanocomposites. The microstructures of nanocomposites were confirmed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The crystallization rate of nanocomposites investigated by differential scanning calorimetry (DSC) does not increase despite the presence of clay, which may be due to the physical hindrance of organic modifiers in the clay dispersion. Nanocomposites exhibited enhanced mechanical properties such as strength and stiffness relative to the virgin polymer. In addition, thermal stability was confirmed to be improved by thermogravimetric analysis (TGA). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2144–2150, 2004     

Isothermal and nonisothermal crystallization kinetics of syndiotactic polystyrene/clay nanocomposites

Differential scanning calorimeter (DSC) and X‐ray diffraction methods were used to investigate the isothermal and nonisothermal crystallization behavior and crystalline structure of syndiotactic polystyrene (sPS)/clay nanocomposites. The sPS/clay nanocomposites were prepared by mixing the sPS polymer solution with the organically modified montmorillonite. DSC isothermal results revealed that introducing 5 wt% of clay into the sPS structure causes strongly heterogeneous nucleation, inducing a change of the crystal growth process from mixed three‐dimensional and two‐dimensional crystal growth to two‐dimensional spherulitic growth. The activation energy of sPS drastically decreases with the presence of 0.5 wt% clay and then increases with increasing clay content. The result indicates that the addition of clay into sPS induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). We studied the non‐isothermal melt‐crystallization kinetics and melting behavior of sPS/clay nanocomposites at various cooling rates. The correlation among crystallization kinetics, melting behavior and crystalline structure of sPS/clay nanocomposites is discussed. Polym. Eng. Sci. 44:2288–2297, 2004. © 2004 Society of Plastics Engineers.     

Synthesis and characterization of polypropylene/clay nanocomposites

Polypropylene/clay (PP/clay) nanocomposites were synthesized via intercalative polymerization. The nanostructure of the composites was investigated by wide‐angle X‐ray diffractometry (WAXD) and transmission electron microscopy (TEM). The WAXD patterns of the PP/clay nanocomposites indicated that the characteristic diffraction peak of the clay disappeared. The TEM image showed the clay was exfoliated into nanometer size and dispersed uniformly in the PP matrix. The composites exhibited much higher storage modulus compared to that of pure PP. At temperatures higher than T_g, the storage modulus of the PP/clay nanocomposites with 8.1 wt % clay content increased three times that of the pure PP. Additionally, the thermal stability of the nanocomposites significantly increased. The maximum decomposition temperature was increased by 44°C with the introduction of about 10 wt % clay. The heat‐distortion temperatures (HDTs) of the nanocomposites also increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3611–3617, 2001     

Studies on nylon 6/clay nanocomposites by melt‐intercalation process

The preparation of nylon 6/clay nanocomposites by a melt‐intercalation process is proposed. X‐ray diffraction and DSC results show that the crystal structure and crystallization behaviors of the nanocomposites are different from those of nylon 6. Mechanical and thermal testing shows that the properties of the nanocomposites are superior to nylon 6 in terms of the heat‐distortion temperature, strength, and modulus without sacrificing their impact strength. This is due to the nanoscale effects and the strong interaction between the nylon 6 matrix and the clay interface, as revealed by X‐ray diffraction, transmission electron microscopy, and Molau testing. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1133–1138, 1999     

Mechanical properties and structures of dicyanate–clay nanocomposites

Dicyanate–clay nanocomposites comprising a dicyanate resin and a type of organically modified clay were prepared and characterized, and their thermomechanical properties were investigated. The organically modified clay had silicate layers of nanometer size intercalated with an organic modifier, which improved the compatibility between the clay and organic materials, such as dicyanate resins. Dynamic mechanical analysis was performed to investigate the thermomechanical properties of the dicyanate–clay nanocomposites containing various amounts of the clay. The storage modulus of the nanocomposites below their glass‐transition temperatures slightly increased with increasing clay content. The glass‐transition temperature of the dicyanate–clay nanocomposites increased with increasing clay content. The nanostructures of the dicyanate–clay nanocomposites were characterized by transmission electron microscopy and X‐ray diffraction analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2629–2633, 2003     

Synthesis of resol–layered silicate nanocomposites by reaction exfoliation with acid‐modified montmorillonite

Resol–layered silicate nanocomposites were prepared by the intercalative polymerization of phenol and formaldehyde in the presence of acid‐modified montmorillonite (HMMT). The nanocomposites were studied by means of X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic mechanical analysis (DMA), and rheological measurements. The exfoliation of HMMT was promoted by the intragallery reactions catalyzed by protons in the galleries of the clay, whereas the extragallery polymerization catalyzed by ammonia went on simultaneously. The nanocomposites showed higher glass‐transition temperatures in the DMA diagram compared with the resol counterparts. The impact strength was improved significantly by the incorporation of the clay. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 791–797, 2004     

Preparation of syndiotactic polystyrene/montmorillonite nanocomposites via in situ intercalative polymerization of styrene with monotitanocene catalyst

Syndiotactic polystyrene (sPS)/montmorillonite nanocomposites were prepared via in situ intercalative coordination polymerization using mono‐(η⁵‐pentamethylcyclopenta‐ dienyl) tribenzyloxy titanium [Cp*Ti(OBz)₃] complex activated by methylaluminoxanes (MAO) and triisobutylaluminum (TIBA). The influences of polymerization conditions, such as the weight ratio of montmorillonite and styrene, temperature, and monomer concentration, on the preparation of sPS/montmorillonite nanocomposites was investigated. The intercalation spacing in the nanocomposites, as well as the exfoliation of the montmorillonite interlayers, was characterized with wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM). The dispersibility of the nanoscale elements depended on the polymerization conditions and the surfactant treatment. The crystallizability and thermal properties of these nanocomposites were determined by differential scanning calorimetry (DSC) analysis and thermogravimetric analysis (TGA). Experimental results indicated that the degree of crystallinity of the sPS nanocomposite increased with increasing montmorillonite content and with higher T_g and thermal decomposition temperature than pure sPS. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1412–1417, 2005     

Microstructure‐properties correlations in dynamically vulcanized nanocomposite thermoplastic elastomers based on PP/EPDM

Thermoplastic vulcanized (TPV) nanocomposites were prepared in a laboratory mixer using EPDM, polypropylene of different viscosities, maleic anhydride modified polypropylene, an organo‐clay, and a sulfur‐based curing system. Based on the obtained results from X‐ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), differential scanning calorimeter, and mechanical properties, the microstructure of the prepared nanocomposites was found to be sensitive to the viscosity difference between the two phases and the clay content. X‐ray diffraction and TEM images of the TPV nanocomposites showed that clay was nearly exfoliated and randomly distributed into the polypropylene phase. The SEM photomicrographs of the dynamically vulcanized thermoplastic elastomer samples showed that the rubber particles were dispersed through the polypropylene in form of aggregates and their size increased with the introduction of clay. The nanoscale dimensions of the dispersed clay resulted in a significant improvement of the tensile modulus of the TPV nanocomposite samples, from 20 to 90% depending on clay content and the viscosity ratio of PP/EPDM. In the PP nanocomposites, the clay layers act as nucleating agents, resulting in higher crystallization temperature and reduced degree of crystallinity. Moreover, the oxygen permeability in the TPV nanocomposites was found to be lower than in unfilled but otherwise similar materials. POLYM. ENG. SCI., 47:207–217, 2007. © 2007 Society of Plastics Engineers.     

Polymorphic behavior of nylon 6/saponite and nylon 6/montmorillonite nanocomposites

X‐ray diffraction methods and DSC thermal analysis have been used to investigate the structural change of nylon 6/clay nanocomposites. Nylon 6/clay has prepared by the intercalation of ε‐caprolactam and then exfoliaton of the layered saponite or montmorillonite by subsequent polymerization. Both X‐ray diffraction data and DSC results indicate the presence of polymorphism in nylon 6 and in nylon 6/clay nanocomposites. This polymorphic behavior is dependent on the cooling rate of nylon 6/clay nanocomposites from melt and the content of saponite or montmorillonite in nylon 6/clay nanocomposites. The quenching from the melt induces the crystallization into the γ crystalline form. The addition of clay increases the crystallization rate of the α crystalline form at lower saponite content and promotes the heterophase nucleation of γ crystalline form at higher saponite or montmorillonite content. The effect of thermal treatment on the crystalline structure of nylon 6/clay nanocomposites in the range between Tg and Tm is also discussed.     

Polymer‐Clay Nanocomposites Based on Blends of Polyamide‐6 and Polyethylene

The preparation of polyamide‐6/clay, high‐density polyethylene/clay, and high‐density polyethylene/ polyamide‐6/clay nanocomposites is considered. X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and Fourier Transform Infrared (FTIR) measurements show that the clay enhances the crystallization of the γ‐form of polyamide‐6. The clay also acts as a nucleation agent and causes a reduction of spherulitte size. Scanning electron microscopy (SEM) analysis of fracture surfaces shows that the clay reduces the PA‐6 particle size in the HDPE/PA‐6/clay nanocomposites and changes the morphology. Mechanical properties and the effect of maleated polyethylene are also reported.     

Synthesis and characterization of poly(glycidyl methacrylate)/Na‐montmorillonite nanocomposites

Poly(glycidyl methacrylate)/Na–montmorillonite nanocomposites were synthesized by free‐radical polymerization of glycidyl methacrylate containing dispersed montmorillonite. By changing the concentration of glycidyl methacrylate several polymer–clay nanocomposites were prepared and the resulting nanocomposites were characterized by X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis. The results indicated that the properties of the composite were significantly improved. The thermogravimetric analysis results revealed that the degradation temperatures of nanocomposites were higher than that of pure polymer and the thermal degradation rates decreased. Examination of these materials by scanning electron microscopy showed that the clay layers are dispersed homogenously in the polymer matrix and the formation of intercalation nanostructure. Furthermore, adsorptive, moisture regain, and water uptake properties of nanocomposites were also investigated. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1532–1538, 2004     

Effect of clay addition on the morphology and thermal behavior of polyamide 6

The nanostructure, morphology, and thermal properties of polyamide 6 (PA6)/clay nanocomposites were studied with X‐ray scattering, differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The wide‐angle X‐ray diffraction (WAXD) and TEM results indicate that the nanoclay platelets were exfoliated throughout the PA6 matrix. The crystallization behavior of PA6 was significantly influenced by the addition of clay to the polymer matrix. A clay‐induced crystal transformation from the α phase to the γ phase for PA6 was confirmed by WAXD and DSC; that is, the formation of γ‐form crystals was strongly enhanced by the presence of clay. With various clay concentrations, the degree of crystallinity and crystalline morphology (e.g., spherulite size, lamellar thickness, and long period) of PA6 and the nanocomposites changed dramatically, as evidenced by TEM and small‐angle X‐ray scattering results. The thermal behavior of the nanocomposites was investigated with DSC and compared with that of neat PA6. The possible origins of a new clay‐induced endothermic peak at high temperature are discussed, and a model is proposed to explain the complex melting behavior of the PA6/clay nanocomposites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1191–1199, 2007     

Mesua ferrea L. seed oil based highly branched polyester/epoxy blends and their nanocomposites

Mesua ferrea L. seed oil based highly branched polyester and epoxy resins blends were prepared by mechanical mixing at different weight ratios. The best performing blend was used as the matrix for the preparation of nanocomposites with different dose levels of organophilic montmorillonite (OMMT) nanoclay. The prepared nanocomposites were characterized by X‐ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and transmission electron microscopy. Data resulting from the mechanical and thermal studies of the blends and nanocomposites indicated improvements in the tensile strength and thermal stability to appreciable extents for the nanocomposites with OMMT loading. The nanocomposites were characterized as well‐dispersed, partially exfoliated structures with good interfacial interactions. From the X‐ray diffraction analysis, the absence of d₀₀₁ reflections of the OMMT clay in the cured nanocomposites indicated the development of an exfoliated clay structure, which was confirmed by transmission electron microscopy. The homogeneous morphologies of the pure polyester/epoxy blend and clay hybrid systems were ascertained with scanning electron microscopy. The tensile strength of the 5 wt % clay‐filled blend nanocomposite system was increased by 2.4 times compared to that of the pure blend resin system. The results suggest that the prepared nanocomposites have the potential to be used as active thin films for different applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Enhancement of radiation‐resistant effect in ethylene–vinyl acetate copolymers by the formation of ethylene–vinyl acetate copolymers/clay nanocomposites

Ethylene–vinyl acetate (EVA) copolymers/clay nanocomposites, prepared by using nonreactive organophilic clay and reactive organophilic clay, were characterized by X‐ray diffraction and by high‐resolution transmission electron microscopy. The influence of gamma irradiation on the structure and properties of the pure EVA and EVA/clay nanocomposites was systematically investigated. In the presence of gamma radiation, the clay can effectively restrain the increase of the storage modulus of EVA/clay nanocomposites, which was supported by dynamical mechanical analysis. Gamma irradiation had almost no effect on the thermal properties of EVA/clay nanocomposites by using nonreactive organophilic clay, but it obviously improved the thermal stability of EVA/clay nanocomposites by using reactive organophilic clay. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2532–2538, 2005     

The effect of crystallization on the structure and morphology of polypropylene/clay nanocomposites

The effect of crystallization on the structure and morphology of maleic anhydride grafted polypropylene (PP‐MA)/clay (montmorillonite) nanocomposites (PPCNs) is presented. Wide‐angle X‐ray diffraction (WAXD) measurements of PPCNs crystallized at different temperatures show that the extent of intercalation increases with the crystallization temperature. The enhancement of intercalation occurs with lower clay content PPCNs, and maximum intercalation takes place for 4 wt% clay content. The mechanism of intercalation has been proposed through crystallization. Excess γ‐form of the crystallite of PP‐MA appears in presence of clay, possibly because of the confinement of the polymer chain between the clay particles. WAXD data also reveals that d‐spacing increases gradually with clay content. The decrease of spherulitic size is observed with increasing clay content, which indicates that clay particles act as nucleating agents. Lamellar textures have been explored by using small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM), which exhibit that both the lamellar thickness and long period of the PPCNs are higher than those of PP‐MA.     

Intumescent flame retardant–montmorillonite synergism in polypropylene‐layered silicate nanocomposites

Polypropylene/clay nanocomposites have been prepared starting from pristine mont morillonite (MMT) and reactive compatibilizer hexadecyltrimethylammonium bromide (C16). The nanocomposite structure is evidenced by the X‐ray diffraction and high resolution electronic microscopy. Intumescent flame retardant has been added to polypropylene/clay hybrids. Their flammability behaviours have been evaluated using cone calorimetry. Synergy was observed between the nanocomposites and intumescent flame retardant. Copyright © 2003 Society of Chemical Industry     

Effect of clay with different cation exchange capacity on the morphology and properties of poly(methyl methacrylate)/clay nanocomposites

PMMA/clay nanocomposites were successfully prepared by in situ free‐radical polymerization with the organic modified MMT‐clay using methyl methacrylate monomer and benzoyl peroxide initiator. Two clays with different cation exchange capacity have been used to prepare and compare the several properties. The clays have been modified using Amphoterge K2 by ion exchange reaction to increase the compatibility between the clay and polymer matrices. The modified clays have been characterized by wide‐angle X‐ray diffraction pattern, Fourier transform infrared spectroscopy, and thermogravimetric analysis (TGA). The powdered X‐ray diffraction and transmission electron microscopy techniques were employed to study the morphology of the PMMA/clay nanocomposites which indicate that the modified clays are dispersed in PMMA matrix to form both exfoliated and intercalated PMMA/modified clay nanocomposites. The thermomechanical properties were examined by TGA, differential scanning calorimetry, and dynamic mechanical analysis. Gas permeability analyzer shows the excellent gas barrier property of the nanocomposites, which is in good agreement with the morphology. The optical property was measured by UV–vis spectroscopy which shows that these materials have good optical clarity and UV resistance. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Synthesis and characterization of sPS/montmorillonite nanocomposites

The present work analyzed the possibility of obtaining and producing syndiotactic polystyrene (sPS)–based nanocomposites. The work first focused on possible technology to use for intercalation from solution and melt intercalation. Using a blend of sPS with atactic polystyrene (aPS) as the matrix was also considered. Thermal analysis techniques, such as differential scanning calorimetry (DSC) and thermogravimetry (TGA), were used to study the thermal properties and stability of the nanocomposites obtained and to select the most appropriate nanocharges. The effect of the introduction of nanofillers on these properties also was evaluated. X–ray diffraction was used to investigate the degree of clay exfoliation. Finally, mechanical characterization of the nanocomposites obtained was performed and compared to that of the pure material. The tests demonstrated that nanodispersion of phyllosilicate layers improved the mechanical behavior of the polymers analyzed, especially the annealed sPS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4957–4963, 2006     

Synthesis and properties of polystyrene–clay nanocomposites via in situ intercalative polymerization

Organophilic montmorillonite (MMT) was prepared by ion exchange between Na⁺ ions in the clay and twin benzyldimethyloctadecylammonium bromine cations in an aqueous medium. The organophilic MMT particles were easily dispersed and swollen in styrene monomer. Polystyrene–MMT nanocomposites were prepared by the free‐radical polymerization of styrene containing dispersed clay. The intercalation spacing in the nanocomposites and the degree of dispersion of these composites were investigated with X‐ray diffraction and transmission electron microscopy, respectively. The nanocomposites had higher weight‐average molecular weights, lower glass‐transition temperatures, and better thermal stability (the decomposition temperature was improved by ca. 70°C) than the virgin polystyrene. The rheological behavior of the polystyrene–MMT nanocomposites was also studied. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 201–207, 2005     

Effect of clay on properties of polyimide‐clay nanocomposites

Effect of clay on mechanical, thermal, moisture absorption, and dielectric properties of polyimide‐clay nanocomposites was investigated. Nanocomposites of polyimide (ODA‐BSAA) hybridized with two modified clay (PK‐802 and PK‐805) were synthesized for comparison. The silicate layers in the polymer matrix were intercalated/exfoliated as confirmed by wide‐angle X‐ray diffraction and transmission electron microscopy. Thermal stability, moisture absorption, and storage modulus for these nanocomposites are improved as hybridized clay increases. Reduced dielectric constants due to the hybridization of layered silicates are observed at frequencies of 1 kHz–1 MHz and temperatures of 35–150°C. The tetrahedrally substituted smectite (PK‐805) resulted in higher mechanical strength and dielectric constants than those of octahedrally substituted smectite (PK‐802), which could be attributed to their stronger ionic bonding between clay layer and polymer matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 318–324, 2007