Phase separation of unsaturated polyester resin blended with poly(vinyl acetate)

The behavior of phase separation during the curing reaction of unsaturated polyester (UPE) resin in the presence of low profile additive, that is, poly(vinyl acetate) (PVAc), was studied by low-angle laser light scattering (LALS) and scanning electron microscopy (SEM). The experimental results revealed that the PVAc-rich phase was regularly dispersed in the cured styrene–UPE matrix for styrene–UPE resin blended with 5 wt % of PVAc. As the PVAc content was increased higher than 10 wt %, a cocontinuous PVAc and cured styrene–UPE phase was observed for the cured systems. The LALS observations were carried out in situ at a curing temperature of 100°C; thus, the effect of the rate of exothermic heat released from curing reaction on the morphology of curing system was investigated and reported in this work. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2413–2428, 1999     

Microgelation of unsaturated polyester resins in the presence of poly(vinyl acetate) by static and dynamic light scattering

The partially cured unsaturated polyester (UPE)/styrene resins with various degrees of conversion lower than gel conversion blended with PVAc and 2‐fluorotoluene solvent were investigated using both static and dynamic light scattering (SLS and DLS). The solvent (i.e., 2‐fluorotoluene) is isorefractive with PVAc; thus, one sees only primary and partially cured UPEs in light‐scattering experiments. DLS was used to follow the variations of primary UPE and UPE microgel particle sizes, and SLS was used to follow the variations of UPE molecular weight, second virial coefficient (A₂), anisosymmetry (ρ_v), and differential index refraction (dn/dC) with degree of UPE conversion and PVAc concentration. The experimental data showed that, at a fixed degree of UPE/styrene conversion, increasing PVAc concentration in the UPE/styrene system caused decreases in dn/dC, A₂, ρ_v, and particle sizes of UPE microgels. These results suggest that mixing PVAc into UPE/styrene resins causes an increase in the compactness of UPE coils and favors intramolecular UPE/styrene cyclization in the early stage of curing. Thus A₂, ρ_v, and particle sizes of microgels decreased with increasing PVAc concentration. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1439–1449, 2001     

Phase separation,cure kinetics,and morphology of epoxy/poly(vinyl acetate) blends

Epoxy based on diglycidyl ether of bisphenol A + 4,4′diaminodiphenylsulfone blended with poly(vinyl acetate) (PVAc) was investigated through differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and environmental scanning electron microscopy (ESEM). The influence of PVAc content on reaction induced phase separation, cure kinetics, morphology and dynamic‐mechanical properties of cured blends at 180°C is reported. Epoxy/PVAc blends (5, 10 and 15 wt % of PVAc content) are initially miscible but phase separate upon curing. DMTA α‐relaxations of cured blends agree with T_g results by DSC. The conversion‐time data revealed the cure reaction was slower in the blends than in the neat system, although the autocatalytic cure mechanism was not affected by the addition of PVAc. ESEM showed the cured epoxy/PVAc blends had different morphologies as a function of PVAc content: an inversion in morphology took place for blends containing 15 wt % PVAc. The changes in the blend morphology with PVAc content had a clear effect on the DMTA behavior. Inverted morphology blends had low storage modulus values and a high capability to dissipate energy at temperatures higher than the PVAc glass‐transition temperature, in contrast to the behavior of neat epoxy and blends with a low PVAc content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1507–1516, 2007     

Toughening epoxy resins with polyepichlorohydrin

Polyepichlorohydrin (PECH) rubbers were found to toughen epoxy resins based on the diglycidyl ether of bisphenol A (DGEBA) and cured with piperidine. The degree of toughening depends on the molecular weight of the PECH and on the curing temperature. Best toughening was achieved with PECH of the highest nominal molecular weight of 3400 (Hydrin 10 × 2). Hydrin 10 × 1 (nominal molecular weight 1700) did not toughen the epoxy resin unless bisphenol A was also added, whereas Hydrin 10 × 2 toughened it in the absence of bisphenol A. Curing resins containing bisphenol A and Hydrin 10 × 1 at 160°C resulted in a slightly more brittle resin than when cured at 120°C. The effect of PECH rubbers on the T_g, modulus, and hot/wet properties is similar to that of carboxy-terminated butadiene-acrylonitrile rubbers (CTBN). Dynamic mechanical thermal analysis (DMTA) and scanning electron micrographs (SEM) of fractured surfaces show that the PECH separates as a discrete phase during curing. © 1993 John Wiley & Sons, Inc.     

Acrylated epoxidized soybean oil as a styrene replacement in a dicyclopentadiene‐modified unsaturated polyester resin

Nonvolatile and nonhazardous acrylated epoxidized soybean oil (AESO) was investigated as a replacement for hazardous styrene in a commercial unsaturated polyester (UPE) resin [a mixture of styrene and a dicyclopentadiene (DCPD)‐modified UPE (DCPD–UPE)]. DCPD–UPE was prepared from ethylene glycol, diethylene glycol, maleic anhydride, and DCPD. Mixtures of AESO and DCPD–UPE [AESO–(DCPD–UPE) resins] were found to be homogeneous, easily pourable solutions at room temperature. The glass‐fiber‐reinforced composites from the AESO–(DCPD–UPE) resins were comparable or even superior to those from the mixture of styrene and DCPD–UPE in terms of the flexural and tensile strengths. The viscoelastic properties of the cured AESO–(DCPD–UPE) resins and the corresponding glass‐fiber‐reinforced composites were characterized by dynamic mechanical analysis. The viscosities and pot lives of the AESO–(DCPD–UPE) resins as a function of the temperature were studied. The curing mechanism of the AESO–(DCPD–UPE) resins is discussed. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46212.     

Laboratory investigation of the properties of asphalt modified with epoxy resin

Epoxy asphalts were prepared by mixing styrene–butadiene–styrene (SBS) modified asphalt with epoxy resin. The curing process and morphology of epoxy asphalts were characterized by infrared spectroscopy and fluorescent microscope, respectively. The effects of epoxy resin contents, ratio of curing agent to epoxy resin and curing temperature on properties of epoxy asphalt were investigated. Results indicated that epoxy resin and epoxy asphalt showed similar curing efficiency. Epoxy asphalts can be cured at 120 or 60°C and its viscosity at 120°C can meet the demands of asphalt mixture mixing and paving. The chemical reaction of epoxy resin in epoxy asphalt is slow and reaction occurs not only with the curing agent but also carboxylic acid in epoxy asphalt. The microstructure of epoxy asphalt transforms from the dispersed structure to networks structure with epoxy resin content increasing and phase transition starts when 30 wt % epoxy resin present in asphalt. The softening point and tensile strength of epoxy asphalt increased with epoxy resin contents increasing. The softening point and tensile strength of epoxy asphalt were markedly improved when epoxy resin content was more than 30 wt %, which is attributed to formation of continuous structure of epoxy resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Resin transfer molding of natural fiber reinforced polybenzoxazine composities

Kenaf fiber is incorporated in a polybenzoxazine (PBZX) resin matrix to form a unidirectionally reinforced composite containing 20 wt% fiber by a resin transfer molding technique. Two types of benzoxazine monomer are synthesized and used as resin mixtures: Benzozazines based on bisphenol‐A/aniline (BA‐a) and phenol/aniline (Ph‐a). The effects of varying BA‐a:Ph‐a ratio in the resin mixture and curing conditions on mechanical properties of pure PBZX resin and kenaf/PBZX composites are studies. The Flexural strength of the pure PBZX resin increases with increasing ratio of BA‐a:Ph‐a, curing temperature and curing time, but the impact strength increases only slightly. PBZX resin has lower water absorption and higher flexural modulus, when compared with unsaturated polyester (UPE) resin. PBZX composites with 20 wt% fiber content have lower flexural and impact strengths, but higher moduli compared with UPE composites with the same fiber content.     

Structure of the carbon chain polymer in unsaturated polyesters

The curing behaviour of thick laminates was simulated by curing thin polyester sections isothermally at various temperatures. Unsaturated polyesters with different ratios of styrene to unsaturations in the polyester were cured with benzoyl peroxide and subjected to hydrolytic degradation. The molecular size and structure of the carbon chain polymer was examined by size exclusion liquid chromatography and high resolution ¹³C FT n.m.r. analysis and was found to depend on the reaction temperature. The overall values of the molecular weights ranged from 12 000 to 36 000, which is a magnitude lower than those reported earlier. There was a similar tendency for molar ratios of styrene to unsaturations in the resin varying between 1.25 and 2.00. In the region 60°C–80°C the molecular weight increased with increasing temperature and then, from a maximum at 80°C–90°C, the molecular weight decreased with cure temperature. For the molar ratio of styrene to unsaturations of 2.25 the molecular weight decreased with increasing cure temperature. The average styrene sequence lengths were not found to deviate from the ratio expected from the stoichiometry in the resin before curing except for temperatures below 70°C and above 120°C.     

Synthesis and characterization of bis(4‐cyanato 3,5‐dimethylphenyl) naphthyl methane/epoxy/glass fiber composites

Bis(4‐cyanato 3,5‐dimethylphenyl) naphthylmethane was prepared by treating CNBr with bis(4‐hydroxy 3,5‐dimethylphenyl) naphthylmethane in the presence of triethylamine at −5 to 5°C. The dicyanate was characterized by FT‐IR and NMR techniques. The prepared dicyanate was blended with commercial epoxy resin in different ratios and cured at 120°C for 1 hr, 180°C for 1 hr, and post cured at 220°C for 1 hr using diamino diphenyl methane (DDM) as curing agent. Castings of neat resin and blends were prepared and characterized by FT‐IR technique. The morphology of the blends was evaluated by SEM analysis. The composite laminates were also fabricated from the same composition using glass fiber. The mechanical properties like tensile strength, flexural strength, and fracture toughness were measured as per ASTMD 3039, D 790, and D 5528, respectively. The tensile strength increased with increase in cyanate content (3, 6, and 9%) from 322 to 355 MPa. The fracture toughness values also increased from 0.7671 kJ/m² for neat epoxy resin to 0.8615 kJ/m² for 9% cyanate ester epoxy modified system. The thermal properties were also studied. The 10% weight loss temperature of pure epoxy is 358°C and it increased to 398°C with incorporation of cyanate ester resin. The incorporation of cyanate ester up to 9% loading level does not affect the T_g to a very great extent. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Curing and Morphology of BPA Epoxy Resin/LC Epoxy Resin PEPEB Composites

Liquid crystalline epoxy resin (LC epoxy resin) – p-phenylene di{4-[2-(2,3-epoxypropyl)ethoxy]benzoate} (PEPEB) was synthesized. The mixture of PEPEB with bisphenol-A epoxy resin (BPAER) was cured with a curing agent 4,4-diamino-diphenylmethane (DDM). The curing process and thermal behavior of this system were investigated by differential scanning calorimeter (DSC) and torsional braid analysis (TBA). The morphological structure was measured by polarizing optical microscope (POM) and scanning electron microscope (SEM). The results show that the initial curing temperature Ticu (gel point) of this system is 68.1°C, curing peak temperature T _pcu is 102.5°C, and the disposal temperature T _fcu is 177.6°C. LC structure was fixed in the cured epoxy resin system. The curing kinetics was investigated by dynamic DSC. Results showed that the curing reaction activation energy of BEPEB/BPAER/DDM system is 22.413 kJ/mol. The impact strength is increased 2.3 times, and temperature of mechanical loss peak is increased to 23°C than the common bisphenol-A epoxy resin, when the weight ratio of BEPEB with BPAER is 6 100.     

Preparation and thermal properties of bio‐based gallic acid epoxy/carbon nanotubes composites by cationic ring‐opening reaction

In order to prepare the bio‐based polymeric materials, a gallic acid epoxy resin (GA‐ER) is synthesized by using biodegradable gallic acid, and the nanocomposites of GA‐ER/glycidyl methacrylate (GMA)/multiwalled carbon nanotubes (MWCNTs) were prepared by dual hybrid cationic ring‐opening reaction. Differential scanning calorimetry (DSC) results show that the curing reaction temperature of the nanocomposites is between 150 and 225°C. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results suggest that MWCNTs are homodispersing in the GA‐ER/GMA matrix when the MWCNTs content is not more than 1.0 wt%. The glass transition temperature of the nanocomposite with 0.5 wt% MWCNTs is 9.3°C higher than that of pure resin system. The initial thermal degradation temperature and degradation activation energies E_a of the nanocomposite with 1.0 wt% MWCNTs is 10°C and 68.6 kJ/mol higher than that the pure resin system, respectively. POLYM. COMPOS., 37:3093–3102, 2016. © 2015 Society of Plastics Engineers     

Cure kinetics and conductivity of rigid rod epoxy with polyaniline as a curing agent

The samples of rigid rod epoxy resin (4,4′‐diglycidyl (3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)) with different weight contents of polyaniline (PANI) as a curing agent were prepared. The kinetics of curing reaction between TMBP and PANI was analyzed by dynamic differential scanning calorimetry in the temperature range of 25–300°C. The results showed that the heat of cure reaction of TMBP/PANI sample with 10 wt% PANI was larger than those of others. The active energies with different curing conversions of TMBP/PANI sample with 10 wt% PANI were calculated by iso‐conversional method using the Coats‐Redfern approximation. The results showed that the activation energy was dependent on the degree of conversion. The morphology of the cured samples was detected by scanning electron microscopy measurements. The relationship between morphology and conductivity of cured samples was researched. The conductivities increased from 2.7 × 10⁻⁴ to 9.5 × 10⁻⁴ S/cm with the increase of PANI from 5 to 20 wt% in cured samples. The thermal stabilities of cured TMBP/PANI samples were examined by thermogravimetric analysis. The results showed that the cured TMBP/PANI can be promising to use as a conducting adhesive. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Physical properties of unsaturated polyester resin from glycolyzed pet fabrics

Physical properties of unsaturated polyester resins (UPE resins) prepared from glycolyzed poly (ethylene terephthalate) (PET) and PET/cotton blended fabrics were investigated. Initially, PET and PET/cotton blended fabrics were chemically recycled by glycolysis. The depolymerizations were carried out in propylene glycol with the presence of zinc acetate as a catalyst. The reaction time was varied at 4, 6, and 8 h. The glycolyzed products were then esterified using maleic anhydride to obtain UPE resins. The prepared resins were cured using styrene monomer, methyl ethyl ketone peroxide, and cobalt octoate as a crosslinking agent, an initiator and an accelerator, respectively. The cured resin products were tested for their mechanical properties and thermal stability. The results indicated that, among the fabric based resins, one prepared from the 8‐h glycolyzed product possessed the highest mechanical properties those are tensile strength, tensile modulus, flexural strength, impact strength, and hardness. The highest thermal stability was also found in the cured resin prepared from the 8‐h glycolyzed product. The mechanical properties of fabric based resins were slightly lower than those of the bottle based resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2536–2541, 2007     

Electron beam curing of polymer composites

Electron‐beam (E‐Beam) curing of an epoxy polymer matrix and its composite (reinforced with IM7 Carbon fibers) was studied using a cationic photoinitiator. Photoinitiator concentration, dose, and process temperature were varied to understand their influence on E‐beam curing. Optimal photoinitiator concentration was found to be 5 phr. The curing was due to a primary α reaction with a strong dependence on dose, and a secondary β reaction with a weak dependence on dose and a strong dependence on initiator concentration. The extent of cure increased rapidly with dose until 100 kGy and it approached a plateau value beyond 100 kGy. This plateau value corresponded to incomplete curing by 27% for resin and 22% for composite at a process‐temperature of 22°C. The causes for incomplete curing appear to be the secondary β reaction and diffusional limitation. Increase in process temperature resulted in higher extent of cure at a dose level. The material used in this study was also found to be thermally curable and the reaction onset temperature (measured in a DSC ramp experiment) reduced from about 150°C at 0 kGy to about 50°C at 30 kGy. This indicates that simultaneous thermal curing during E‐beam curing of resin and composite is possible. After thermal post‐curing, the T_g of the E‐beam cured resin increased from 130°C at 200 kGy to a value greater than 370°C and the modulus decreased by 10%. The service temperature and the modulus of the 100% thermally cured resin and the thermally post‐cured (after E‐Beam irradiation) resin were comparable.     

Effect of nanoclay on shrinkage control of low profile unsaturated polyester (UP) resin cured at room temperature

The addition of a small amount of nanoclay (1-3 wt%) can provide excellent volume shrinkage control of unsaturated polyester (UP)/styrene (St)/poly(vinyl acetate) (PVAc) systems cured at room temperature. PVAc serves as the low profile additive (LPA). In this study, both temperature-induced phase separation of the uncured resin mixture and transmission electron microscopy (TEM) of the cured sample revealed that nanoclay resided in the LPA-rich phase, leading to a higher reaction rate and earlier onset of micro-cracking in the LPA-rich phase or at the interface of the LPA-rich and UP-rich phases. Consequently, an earlier volume expansion during curing was observed in reactive dilatometry, resulting in better shrinkage control. On-line measurement of the composite thickness change during vacuum-infusion liquid composite molding [e.g. the Seemann Composite Resin Infusion Molding Process (SCRIMP)] further proved excellent volume shrinkage control of nanoclay filled systems, leading to a smoother composite surface.     

Phase behavior, morphology and interfacial structure in thermoset/thermoplastic elastomer blends of poly(propylene glycol)-type epoxy resin and polystyrene–b-polybutadiene

Thermoset/thermoplastic elastomer (TPE) blends of poly(propylene glycol) (PPG)-type epoxy resin (ER) and a diblock copolymer, polystyrene–b-polybutadiene (SB, with 30% styrene content), were prepared using 4,4′-diaminodiphenylmethane (DDM) as curing agent. The miscibility and thermal transition behavior of DDM-cured ER/SB blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The existence of three separate glass transitions, which are independent of the blend composition, indicates that SB is immiscible with DDM-cured ER. Neither the PS block nor the PB block exhibits miscibility with the cured ER. There exist three phases in the blends: a PS microphase, an ER-rich phase and a PB microphase. The phase structure and morphology of the ER/SB blends were studied using both scanning and transmission electron microscopy (SEM and TEM); a variety of morphologies were observed, depending on the blend composition. For the blends with 5 and 10 wt% SB, SB domains with irregular shapes and broadly distributed sizes are dispersed in a continuous cured ER matrix. For the blends with 20–60 wt% SB, interpenetrating bicontinuous phase structures are observed. For the blends with 70 wt% and more SB, a dispersion of cured ER particles in the SB matrix is obtained. The TEM observation showed that the two phases in the blends exhibit a good interfacial adhesion. The interfacial layer between the ER and SB phases varies from 100 to 300 nm for the blend with 20 wt% SB content, SB micelles are formed surrounding the SB domains in the ER matrix. Small-angle X-ray scattering (SAXS) experiments reveal that the SB diblock polymer still exhibits a lamellar microphase structure within the SB phase and the long spacing of lamellae nearly does not change in the blends. The SB diblock copolymer is microphase separated in the macroscopically phase separated ER/SB blends.     

Preparation,curing kinetics,and thermal properties of bisphenol fluorene epoxy resin

Diglycidyl ether of 9,9‐bis(4‐hydroxyphenyl) fluorene (DGEBF) was synthesized to introduce more aromatic structures into an epoxy resin system. The structure of DGEBF was characterized with Fourier transform infrared and ¹H‐NMR. 4,4′‐Diaminodiphenylmethane (DDM) was used as the curing agent for DGEBF, and differential scanning calorimetry was applied to study the curing kinetics. The glass‐transition temperature of the cured DGEBF/DDM, determined by dynamic mechanical analysis, was 260°C, which was about 100°C higher than that of widely used diglycidyl ether of bisphenol A (DGEBA). Thermogravimetric analysis was used to study the thermal degradation behavior of the cured DGEBF/DDM system: its onset degradation temperature was 370°C, and at 700°C, its char yield was about 27%, whereas that of cured DGEBA/DDM was only 14%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of both silane‐grafted and ion‐exchanged organophilic clay in structural,thermal, and mechanical properties of unsaturated polyester nanocomposites

Unsaturated polyester (UPE) resin including styrene monomer was mixed with organophilic montmorillonite (MMT) clay and its crosslinking polymerization reaction was done in the presence of free‐radical initiator. MMT clay was modified with cetyl trimethly ammonium bromide and trimethoxy vinyl silane. The nanocomposites were characterized by X‐ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), thermogravimetric and dynamic mechanical analyses (TGA and DMA). The exfoliated nanocomposite structure was obtained when the MMT clay was modified in the presence of both modifiers, whereas individual modifications all resulted in intercalated structures. The exfoliated UPE nanocomposite exhibited better thermal and dynamic mechanical properties when compared with pure UPE and other composites, even with 3 wt% clay loading. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effects of poly(methyl methacrylate)‐based low‐profile additives on the properties of cured unsaturated polyester resins. I. Miscibility,curing behavior,and glass‐transition temperatures

The effects of three series of self‐synthesized poly(methyl methacrylate) (PMMA)‐based low‐profile additives (LPAs), including PMMA, poly(methyl methacrylate‐co‐butyl acrylate), and poly(methyl methacrylate‐co‐butyl acrylate‐co‐maleic anhydride), with different chemical structures and MWs on the miscibility, cured‐sample morphology, curing kinetics, and glass‐transition temperatures for styrene (ST)/unsaturated polyester (UP) resin/LPA ternary systems were investigated by group contribution methods, scanning electron microscopy, differential scanning calorimetry (DSC), and dynamic mechanical analysis, respectively. Before curing at room temperature, the degree of phase separation for the ST/UP/LPA systems was generally explainable by the calculated polarity difference per unit volume between the UP resin and LPA. During curing at 110°C, the compatibility of the ST/UP/LPA systems, as revealed by cured‐sample morphology, was judged from the relative magnitude of the DSC peak reaction rate and the broadness of the peak. On the basis of Takayanagi's mechanical models, the effects of LPA on the final cure conversion and the glass‐transition temperature in the major continuous phase of ST‐crosslinked polyester for the ST/UP/LPA systems was also examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3369–3387, 2004     

Synthesis and characterization of emulsion‐type curing agent of water‐borne epoxy resin

Self‐emulsified water‐borne epoxy curing agent of nonionic type was prepared using triethylene tetramine (TETA) and derivative of epoxy resin as a capping agent, which was synthesized by liquid epoxy resin (E51) and polyethylene glycol (PEG), and the curing agent possessed emulsification and curing properties at the same time. The curing agent with good property of emulsifying liquid epoxy resin could be obtained under the condition of the molar ratio of PEG : E51 : TETA as 0.8 : 1 : 3.5 at 80°C for 5 h. The mean particle size of the emulsion liquid was about 220 nm with the prepared curing agent and epoxy resin at the mass ratio of 1 : 3. The structure of the emulsion‐type curing agent was confirmed by FTIR and ¹H NMR spectra, and the mechanism of cured film formation was also analyzed by SEM photographs. The cured film prepared by the emulsion‐type curing agent and epoxy resin under ambient cure conditions showed good properties even at high staving temperature. This study provides useful suggestions for the application of the water‐borne epoxy resins in coating industry. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2652–2659, 2013