Novel promoting effects of cerium on the activities of NO_x reduction by NH_3 over TiO_2-SiO_2-WO_3 monolith catalysts

A series of catalysts were prepared by doping different loadings of CeO2 over TiO2-SiO2-WO3 and used for the selective catalytic reduction of NOx by NH3. The experimental results showed that the selective catalytic reduction（SCR） performance and SO2-resistant ability of TiO2-SiO2-WO3 were greatly enhanced by the introduction of cerium. The catalyst containing 10% CeO2 showed the highest NO conversion in a wide temperature range and good N2 selectivity with broad operation temperature window at the gas hourly space velocity（GHSV） of 30000 h–1, which was a very promising catalyst for NOx abatement from diesel engine exhaust. The catalysts were characterized by X-ray diffraction（XRD）, scanning electron microscopy with energy dispersive X-ray spectroscopy（SEM-EDS）, N2 adsorption-desorption（BET） and X-ray photoelectron spectroscopy（XPS）. The characterization results showed that the bigger pore radius, higher surface atomic concentration and dispersion of Ce and the abundant adsorbed oxygen on the surface of catalyst contributed to the best NH3-SCR performance of CeO2/TiO2-SiO2-WO3 catalyst containing 10% CeO2.     

Low-temperature NH_3-SCR of NO_x over MnCeO_x/TiO_2 catalyst:Enhanced activity and SO_2 tolerance by modifying TiO_2 with Al_2O_3

A series of TiO_2-Al_2 O_3 composites with Al/Ti molar ratios of 0.1,0.2,and 0.4 were synthesized by a coprecipitation method and used as supports to prepare supported MnCeO_x catalysts by an impregnation method.The physico-chemical properties of the samples were extensively characterized by N2 physisorption,X-ray diffraction,Raman spectroscopy,scanning electron micro scopy and energy-dispersive Xray spectroscopy element mapping,X-ray photoelectron spectroscopy,H_2-temperature programmed reduction,ammonia temperature programmed desorption,and in-situ diffuse reflectance infrared Fourier transform spectroscopy.The catalytic activity and resistance to water vapor and SO_2 of the asprepared catalysts for the SCR of NO_x with NH3 were evaluated at 50-250℃ and GHSV of 80000 mL/(g_(cat)·h).The results reveal that MnCeO_x/TiO_2-Al_2 O_3 exhibits higher activity and better SO2 tolerance than MnCeO_x/TiO_2.Combining with the characterization results,the enhanced activity and SO2 tolerance of MnCeO_x/TiO_2-Al_2 O_3 can be mainly attributed to higher relative concentrations of Mn~(4+)and chemisorbed oxygen species,stronger reducibility,and larger adsorption capacity for NH3 and NO,which originate from the larger specific surface area and pore volume,higher dispersion of Mn and Ce species compared with MnCeO_x/TiO_2.Moreover,in situ DRIFTS was used to investigate the reaction mechanism,and the results indicate that the NH3-SCR reaction over MnCeO_x/TiO_2 and MnCeO_x/TiO_2-Al_2 O_3 takes place by both the E-R and L-H mechanisms.     

Effect of different doping elements on performance of Ce-Mn/TiO2 catalyst for low temperature denitration

Sm and Ho were doped in Ce-Mn/TiO₂ catalyst respectively to enhance its denitration performance at low temperature.X-ray diffraction(XRD),N₂ adsorption-desorption,X-ray photoelectron spectroscopy(XPS),NH₃-temperature programmed desorption(NH₃-TPD),H₂-temperature programmed reduction(H₂-TPR) and in situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS) techniques were used to analyze the structure and performance ...     

Influence of MnO2 modification methods on the catalytic performance of CuO/CeO2 for NO reduction by CO

In order to investigate the influence of MnO2 modification methods on the catalytic performance of CuO/CeO2 catalyst for NO reduction by CO,two series of catalysts(xCuyMn/Ce and xCu/yMn/Ce) were prepared by co-impregnation and stepwise-impregnation methods,and characterized by means of X-ray diffraction(XRD),Raman spectra,H2-temperature programmed reduction(H2-TPR),in situ diffuse reflectance infrared Fourier transform spectra(in situ DRIFTS) techniques.Furthermore,the catalytic performances of these catalysts were evaluated by NO+CO model reaction.The obtained results indicated that:(1) The catalysts acquired by co-impregnation method exhibited stronger interaction owing to the more sufficient contact among each component of the catalysts compared with the catalysts obtained by stepwise-impregnation method,which was beneficial to the improvement of the reduction behavior;(2) The excellent reduction behavior was conducive to the formation of low valence state copper species(Cu+/Cu0) and more oxygen vacancies(especially the surface synergetic oxygen vacancies(SSOV,Cu+-□-Mn(4–x)+)) during the reaction process,which were beneficial to the adsorption of CO species and the dissociation of NO species,respectively,and further promoted the enhancement of the catalytic performance.Finally,in order to further understand the difference between the catalytic performances of these catalysts prepared by co-impregnation and stepwise-impregnation methods,a possible reaction mechanism(schematic diagram) was tentatively proposed.     

Preparation and characterization of Ce-Fe-Zr-O(x)/MgO complex oxides for selective oxidation of methane to synthesize gas

A series of Ce-Fe-Zr-O(x)/MgO (x denotes the mass fraction of Ce-Fe-Zr-O, x=10%, 15%, 20%, 25%, 30%) complex oxide oxygen carriers for selective oxidation of methane to synthesis gas were prepared by the co-precipitation method. The catalysts were characterized by means of X-ray diffraction (XRD) and H₂-TPR. The XRD measurements showed that MgFeO₄ particles were formed and Fe₂O₃ particles well dispersed on the oxygen carriers. The reactions between methane diluted by argon (10% CH₄) and oxygen carriers were investigated. Suitable content of CeO₂/Fe₂O₃/ZrO₂ mixed oxides could promote the reaction between methane and oxygen carriers. There are mainly two kinds of oxygen of carriers: surface lattice oxygen which had higher activity but lower selectivity, and bulk lattice oxygen which had lower activity but higher selectivity. Among all the catalysts, Ce-Fe-Zr-O(20%)/MgO exhibited the best catalytic performance. The conversion of the methane was above 56%, and the selectivity of the H₂ and CO were both above 93%, the ratio of H₂/CO was stable and approached to 2 for a long time.     

Interdiffusion in the TiO2 oxidation product of Ti3Al

Oxidation experiments have been conducted on Ti₃Al in the temperature range 1023 to 1273 K in a one-atmosphere pure oxygen environment. The oxidation products were analyzed using the scanning electron microscope (SEM), energy-dispersive spectrometer (EDS), and X-ray diffraction (XRD) techniques and found to be predominantly TiO₂ (rutile). The oxidation rate was observed to obey the parabolic rate law. Diffusivity data were obtained using the parabolic rate constant for interdiffusion of Ti and O in the oxide layer. Parabolic rate constants were calculated from oxidation rate data, and Valenci equations for flat sheets were used to calculate diffusion coefficients. The activation energy, Q, was found to be 295.43±5.90 kJ/mol, and the frequency factor, D ₀, was calculated to be 0.68±0.01 m²/s for oxygen in the TiO₂. The activation energy obtained in this study matches closely with that of oxygen diffusion in TiO₂ reported in the literature.     

Effects of loading transition metal(Mn,Cr,Fe,Cu) oxides on oxygen storage/release properties of CeO_2-ZrO_2 solid solution

Cerium zirconium-based(CZ) oxygen storage materials(OSMs) play a crucial role in three-way catalysts(TWCs),while CZ needs to be modified to satisfy more rigorous emission standard.In this study,transition metal(TMs=Mn,Cr,Fe,Cu) oxides modified CZ were prepared by incipient wetness impregnation method to improve the oxygen storage capacity of CZ-based materials.To clearly illustrate the influence of TM oxides,N_2 adsorption-desorption,X-ray diffraction(XRD),oxygen storage capacity(OSC),temperature programmed reduction by H_2(H_2-TPR) and X-ray photoelectron spectroscopy(XPS) were used to characterize the physical and chemical properties of samples.It is found that,all modified CZ have higher OSC,lower reduction temperatures than those of pristine CZ.Interaction between TMOs and CZ take precedence over specific surface to influence OSC.Notably,FeO_x/CZ has the highest OSC,which is about 1.9 times that of CZ and it could be attributed to synergistic effect between FeO_x and CZ;CuO_x/CZ has the lowest reduction temperature which is 168℃lower than that of CZ,and it can be explained by hydrogen spillover effect.     

Controllable synthesis of argentum decorated CuOx@CeO2 catalyst and its highly efficient performance for soot oxidation

In this paper, CuO_x@Ag/CeO₂ catalysts were synthesized by simple wet-chemical method and equal volume impregnation method. The obtained catalysts were subjected to soot temperature programmed oxidation (soot-TPO) activity tests and were further characterized by various techniques such as X-ray diffraction (XRD), transmission electron microscopy/high-resolution transmission electron microscopy (TEM/HR-TEM), N₂ physisorption, X-ray photoelectron spectroscopy (XPS) and H₂-temperature programmed reduction (H₂-TPR). The results show that CuO_x@Ag/CeO₂ synthesized presents well controlled core-shell structures, with nano-cube like Cu₂O as the core and Ag decorated polycrystalline CeO₂ grafting layers as the shell. Such core-shell structured CuO_x@Ag/CeO₂ can successfully construct a secondary oxygen delivery channel (CuO_x → CeO₂ → Ag) to effectively transfer bulk oxygen of the catalyst to the soot, resulting in its excellent soot oxidation activity compared to CuO_x@CeO₂. The potential benefiting effect by Ag introduction over Cu@Ag/Ce can be concluded as: (i) pumping lattice oxygen and accelerating gaseous O₂ dissociation to generate significantly increased active surface oxygen content; (ii) modulating a moderate surface oxygen vacancies concentration to maintain more highly active O₂^– species.     

Promoting effect and mechanism of neodymium on low-temperature selective catalytic reduction with NH3 over Mn/TiO2 catalysts

Series of Mn/TiO₂ catalysts modified with various contents of Nd for low-temperature SCR were synthesized. It can be found that the appropriate amount of Nd can markedly reduce the take-off temperature of Mn/TiO₂ catalyst to 80 °C and NO_x conversion is stabilized over 90% in the wide temperature range of 100–260 °C. 0.1Nd–Mn/Ti shows higher N₂ selectivity and better SO₂ resistance than Mn/Ti catalyst. The results reveal that Nd-doped Mn/TiO₂ catalyst exhibits larger BET surface area and better dispersion of active component Mn₂O₃. XPS results indicate that the optimal 0.1Nd–Mn/Ti sample possesses higher concentration of Mn⁴⁺ and larger amount of adsorbed oxygen at the surface compared with the unmodified counterpart. In situ DRIFTS show that the surface acidity is evidently increased after adding Nd, especially, the Lewis acid sites, and the intermediate (-NH₂) is more stable. The reaction mechanism over Mn/Ti and 0.1Nd–Mn/Ti catalysts obey the Eley-Rideal (E-R) mechanisms under low temperature reaction conditions. H₂-TPR results show that Nd–Mn/TiO₂ catalyst exhibits better low-temperature redox properties.     

In-situ DRIFT assessment on strengthening effect of cerium over FeO_x/TiO_2 catalyst for selective catalytic reduction of NO_x with NH_3

Fe-based catalysts have a great potential to be used for selective catalytic reduction(SCR) of NO_x with NH3 reaction due to their low cost,nontoxicity and excellent catalytic activity.The aim of this paper is to investigate Ce doping effect on activity of NH_3-SCR over the FeO_x/TiO_2 catalyst.In-situ diffuse reflectance infrared fourier transform(DRIFT) technology was utilized to verity the adsorbed species on the surface of FeO_x/TiO_2 and FeO_x-CeO_2/TiO_2 catalysts.With respect to the obtained results,among the four catalysts studied,the FeO_x-CeO_2/TiO_2 with the FeO_x/CeO_2 ratio of 3/8 shows the best NO conversion more than 98%in the temperature range of 230—350℃,The active centers for NH_3 adsorption and activation are assigned to Lewis acid sites over the FeO_x-CeO_2/TiO_2 and monodentate nitrates can act as the key intermediate in the NH3-SCR.Moreover,both of Langmuir-Hinshelwood and Eley-Rideal mechanisms are observed over the FeO_x-CeO_2/TiO_2 catalysts in the SCR.     

Surface exsolution and local atomic structure of amorphous CeTiOx

We made precipitated nano-ceria (～5 nm) on the surface of the catalyst by heat treatment of Ce-supersaturated amorphous CeTiO_x to improve the oxygen storage properties of CeO₂. The catalysts were prepared by sol-gel methods and TiO₂ nanoparticles were preferentially generated as a core material to form selective Ce-supersaturated structure on the catalyst surface. Reaction temperature and amount of doping element are optimized to induce selective crystallization of CeO₂. CeCe (2nd shell) bond around 0.38 nm of Ce L₃-edge extended X-ray absorption fine structure is reduced and nanostructure of precipitated ceria on the surface is observed by HREM. The catalyst is present as amorphous with precipitated nano-CeO₂ on the surface. The de-NO_x efficiency of the catalyst, which has precipitated CeO₂, improves by ～50% owing to the simultaneous reactions of the nano CeO₂ and the amorphous CeTiO_x.     

Effect of preparation method on MnOx-CeO2 catalysts for NO oxidation

The NO oxidation reaction was studied over MnO_x-CeO₂ catalysts prepared by co-precipitation, impregnation and mechanical mixing method, respectively. It was found that the co-precipitation was the most active and a 60% NO conversion was achieved at 250 °C. X-ray diffraction (XRD), Brumauer-Emmett (BET), H₂-temperature programmed reduction (H₂-TPR) and oxygen storage capacity (OSC) techniques were employed to characterize the physical and chemical properties of the catalysts. XRD results showed that amorphous MnO_x or Mn-O-Ce solid solution existed in co-precipitation and impregnation prepared sample, while crystalline MnO_x was found in mechanical mixing catalyst. A larger surface area was observed on co-precipitation prepared catalyst compared to those prepared by impregnation and mechanical mixing. The strong interaction between MnO_x and CeO₂ enhanced the reducibility of the oxides and increased the amount of Mn⁴⁺ and activated oxygen, which are favorable for NO oxidation to NO₂.     

Effect of manganese and/or ceria loading on V_2O_5-MoO_3/TiO_2 NH_3 selective catalytic reduction catalyst

The effect of manganese and/or ceria loading of V_2 O_5-Mo_O_3/TiO_2 catalysts was investigated for selective catalytic reduction(SCR) of NO_x by NH_3.The manganese and/or ceria loaded V_2 O_5-MoO_3/TiO_2 catalysts we re prepared by the wetness impregnation method.The physicochemical characteristics of the catalysts were thoroughly characterized.The catalytic performance of 1.5 wt% V_2 O_5-3 wt% MoO_3/TiO_2(V1.5 Mo3/Ti) is greatly enhanced by addition of 2.5 wt% MnO_x and 3.0 wt% CeO_2(V1.5 Mo3 Mn2.5 Ce3/Ti) below450℃.Compared with the V1.5 Mo3/Ti catalyst with NO_x conversion of 75% at 275 ℃,V1.5 Mo3 Mn2.5 Ce3/Ti exhibits higher NO_x conversion of 84% with good resistance to SO_2 and H_2 O at a gas hourly space velocity value of 150000 h~(-1).The active manganese,cerium,molybdenum,and vanadium oxide species are highly dispersed on the catalyst surface and some synergistic effects exist among these species.Addition of MnO_x significantly enhances the redox ability of the cerium,vanadium,and molybdenum species.Addition of Ce increases the acidity of the catalyst.More active oxygen species,including surface chemisorbed oxygen,form with addition of Mn and/or Ce.Because of the synergistic effects,appropriate proportions of manganese in different valence states exist in the catalysts.In summary,the good redox ability and the strong acidity contribute to the high NH3-SCR activity and N2 selectivity of the V1.5 Mo3 Mn2.5 Ce3/Ti catalyst in a wide temperature range.And the V1.5 Mo3 Mn2.5 Ce3/Ti catalyst shows good resistance to H_2 O and SO2 in long-time catalytic testing,which can be ascribed to the highly sulfated species adsorbed on the catalyst.     

Enhanced photocatalytic activities of Nd-doped TiO_2 under visible light using a facile sol-gel method

Titanium dioxide nanoparticles modified with neodymium in the range of 1 mol% to 5 mol% were prepared with template-free sol-gel method.The structures of obtained samples were characterized by X-ray powder diffraction analysis.X-ray photoelectron spectroscopy,scanning electron microscopy,transmission electron microscopy and diffuse reflectance spectroscopy.The photocatalytic activity of the obtained samples was evaluated by photodegradation of methyl orange in aqueous solution under ultraviolet-visible(λ 350 nm) and visible(λ 420 nm) irradiation.The experimental results show that the 1 mol% Nd-doped TiO_2 exhibits the highest photocatalytic activity,of which the degradation can reach to 96.5% under visible irradiation.According to the XRD results,the pristine samples are combined with anatase TiO_2 and rutile TiO_2.while the Nd-doped TiO_2 samples are anatase TiO_2 only.This transformation has made an obvious promotion of photocatalyst activity after modification.     

Transition metal doping effect and high catalytic activity of CeO2–TiO2 for chlorinated VOCs degradation

A series of transition metals (Fe, Co, Ni, Cu, Cr and Mn)-doped CeO₂–TiO₂ catalysts were prepared by the sol–gel method and applied for the catalytic removal of 1,2-dichloroethane (DCE) as a model for chlorinated VOCs (CVOCs). The various characterization methods including X-ray diffraction (XRD), N₂ adsorption–desorption, UV-Raman, NH₃ temperature-programmed desorption (NH₃-TPD) and H₂ temperature-programmed reduction (H₂-TPR) were utilized to investigate the physicochemical properties of the catalysts. The results show that doping Fe, Co, Ni or Mn can obviously promote the activity of CeO₂–TiO₂ mixed oxides for DCE degradation, which is related to their improved texture properties, acid sites (especially for strong acidity) and low-temperature reducibility. Particularly, CeTi–Fe doped with moderate Fe exhibits excellent activity for 1,2-dichloroethane (DCE) degradation, giving a T_90% value as low as 250 °C. More importantly, only trace chlorinated byproducts were produced during the low-temperature degradation of various CVOCs (dichloromethane (DCM), trichloroethylene (TCE) and chlorobenzene (CB)) over CeTi–Fe1/9 catalyst with high durability.     

Promotional effect of CO pretreatment on CuO/CeO2 catalyst for catalytic reduction of NO by CO

The CuO/CeO2 catalysts were investigated by means of X-ray diffraction(XRD),laser Raman spectroscopy(LRS),X-ray photoelectronic spectroscopy(XPS),temperature-programmed reduction(TPR),in situ Fourier transform infrared spectroscopy(FTIR) and NO+CO reaction.The results revealed that the low temperature(150 °C) catalytic performances were enhanced for CO pretreated samples.During CO pretreatment,the surface Cu+/Cu0 and oxygen vacancies on ceria surface were present.The low valence copper species activated the adsorbed CO and surface oxygen vacancies facilitated the NO dissociation.These effects in turn led to higher activities of CuO/CeO2 for NO reduction.The current study provided helpful understandings of active sites and reaction mechanism in NO+CO reaction.     

Structure and oxygen storage capacity of Pd/Pr/CeOe-ZrO2 catalyst： effects of impregnated praseodymia

Praseodymium （Pr） was impregnated to CeO2-ZrO2 solid solution by an impregnation method. The as-obtained Pr modi- fied CeO2-ZrO2 was impregnated with 1 wt.% Pd to prepare the catalysts. The structure and reducibility of the fresh and hydrother- really aged catalysts were characterized by X-ray diffraction （XRD）, Raman, X-ray photoelectron spectroscopy （XPS）, CO chemi- sorption and H2 temperature-programmed reduction （H2-TPR）. The oxygen storage capacity （OSC） was evaluated with CO serving as probe gas. Effects of impregnated Pr on the structure and oxygen storage capacity of catalysts were investigated. The results showed that the aged Pr-impregnated samples had much higher OSC and better reducibility than the unmodified ones. The scheme of structural evolutions of the catalysts with and without Pr was also established. Partial of the impregnated Pr diffused into the bulk of CeO2-ZrO2 during ageing, which inhibited the sintering, and increased the amount of oxygen vacancies in CeO2-ZrO2 support. Furthermore, those impregnated Pr species which covered on the surface of the support obstructed the strong metal-support interaction between Pd and Ce so as to reduce the encapsulation of Pd as well as the back spill-over of the oxygen during the catalytic process.     

Hydrophilic and photocatalytic performances of lanthanum doped titanium dioxide thin films

Pure and La-doped TiO2 thin films were prepared on glass by sol-gel method using tetrabutyl titanate as Ti precursors. Their chemical composition, structure and properties were characterized by X-ray d...     

Effect of different supports on activity of Mn–Ce binary oxides catalysts for toluene combustion

The effects of support materials on catalytic performance were investigated in catalytic removal of toluene. And the Mn–Ce binary oxides as active components were supported on ZrO₂, SiO₂, γ-Al₂O₃ and TiO₂ support materials. Many techniques, including X-ray diffraction (XRD), Brunauer–Emmett–Teller method (BET), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR) and NH₃-temperature-programmed desorption (NH₃-TPD), were used to characterize physicochemical properties. Among the different catalysts, the MnCe/ZrO₂ catalyst with the lowest specific surface area (39.7 m²/g) shows the best catalytic activity. In terms of toluene conversion, the activity order is as follows: MnCe/ZrO₂ > MnCe/TiO₂ ≈ MnCe/SiO₂ > MnCe/Al₂O₃. The better performance of MnCe/ZrO₂ should be attributed to the low-temperature reducibility, and abundant surface species (Mn⁴⁺ and lattice oxygen). And XPS and TPR results reveal that more surface abundant Mn and Ce elements generate good interaction in MnCe/ZrO₂. The weak interaction between metal oxide and support also boosts the dispersion and complete reduction of MnCe oxides at low temperature. In addition, the in-situ DRIFTS results clarify that the carbonate species are main intermediates in MnCe/ZrO₂ sample during surface reaction process.     

Photocatalytic degradation of imidacloprid by composite catalysts H3PW12O40/La-TiO2

A series of La-doped TiO2 with different mass fractions were prepared by sol-gel method. Composite catalysts H3PW12O40/La-TiO2 with different loading levels were synthesized using impregnation method. The prepared samples were characterized by fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis diffuse reflectance spectroscopy (DRS) and nitrogen adsorption-desorption analysis. The Keggin structure of H3PW12O40 (HPW) remained intact on the surface of the composites, they had relatively uniform spherical grains of diameter less than 20 nm. The visible light activity of prepared composites were improved by loading HPW and doping La. The prepared composites were used as photocatalysts in degradation of pesticide imidacloprid. Results revealed that 20%H3PW12O40/0.3%La-TiO2 possessed the best photocatalytic activity. Thus, the degradation conversion of imidacloprid reached 98.17% after 60 min irradiation when 20%H3PW12O40/0.3% La-TiO2 was used as catalysts. The degradation of imidacloprid corresponded with first-order kinetic reaction, and the half life of the degradation of imidacloprid was 9.35 min in the optimal conditions.