Ti-10V-2Fe-3Al合金热变形的研究

利用Gleeble3500热模拟试验机对Ti-10V-2Fe-3Al合金两种状态在不同变形温度及不同变形速率条件下的热变形行为进行了研究。结果表明，不同初始状态对合金的应力应变行为影响较大，经过固溶处理后在低于相变点变形时合金的流变应力比较高，但在高于相变点变形时流变应力没有明显差异；合金的应力指数与合金的状态和应变速率有关，大概以0．1s^-1为界分为低应变速率和高应变速率两部分；合金的表观激活能与材料的状态、变形温度及变形速率有关。当两种状态下的合金在温度为650～800℃、应变速率为0．001～0．1s^-1范围内变形时，β相内只发生动态回复，而α相除了发生动态回复外还可能发生动态再结晶；合金在相变点以上变形时只存在着单一的动态回复机制。     

两相区热轧对20钢组织和力学性能的影响

利用Gleeble-3500热模拟试验机对20钢(α+γ)两相区内进行热压缩试验,获得不同变形条件下的真应力-真应变曲线。结果表明,当变形温度相同时,流变应力随着应变速率的增大而增大;当应变速率相同时,流变应力随着变形温度升高而减小,但在850℃时略有增大现象。采用光学显微镜(OM)和场发射扫描电镜(FG-SEM)技术分析了变形温度为750~850℃、应变速率为1s-1时的20钢微观组织变化,并得出结论:20钢在两相区轧制时,在750~820℃范围内,温度是影响力学性能的主要因素;在820~850℃范围内,(α+γ)相变是影响力学性能的主要因素。     

含Sc超高强Al-Zn-Cu-Mg-Zr合金的热变形行为和微观组织

采用热模拟实验对含Sc超高强Al-Zn-Cu-Mg-Zr合金在应变速率为0.001～10s-1、变形温度为380～470℃的条件下进行了热压缩实验.研究了实验合金的流变应力行为和微观组织演变.结果表明:流变应力随变形温度升高而下降;随应变速率增加峰值应力也相应增加.随变形温度升高和应变速率降低,合金动态再结晶的程度加深,亚晶尺寸变大.含Sc超高强Al-Zn-Cu-Mg-Zr合金,形成了Al3Sc弥散相,该相可强烈抑制再结晶.合金主要软化机制为动态回复伴随动态再结晶.     

Ti-IF钢铁素体区热变形行为研究和Zener-Hollomen参数方程的建立

利用单道次压缩变形,研究了变形温度、变形速率和变形程度对一种Ti-IF钢的奥氏体区、铁素体区和两相区的热变形行为的影响.在奥氏体区和铁素体区变形时,随变形温度的降低流变应力增加,而在两相区变形时,随变形温度的降低流变应力降低.Ti-IF钢的铁素体动态再结晶受变形温度的影响最大,在铁素体变形高温区可以发生动态再结晶,铁素体区变形高温区域的变形抗力显著降低.根据流变应力曲线,确定了Ti-IF钢Z-Hollomen参数方程.     

LD7铝合金热变形研究

在Gleeble-1500热模拟机上对LD7铝合金进行等温热变形实验,变形温度为300～500℃,应变速率为0.01～10s-1,研究其热变形的流变应力行为、显微组织及软化机制.结果表明LD7铝合金真应力-真应变曲线表现出动态回复特征,在应变速率ε=1.0s-1,变形温度高于420℃时,应力出现锯齿波动,表现出不连续动态再结晶特征.合金在压缩过程中主要软化机制为动态回复,同时也存在动态再结晶.变形后晶粒尺寸随变形温度升高而增大,随变形速率增加而减小.     

超细晶奥氏体在两相区大变形后的瞬态组织

将一种低碳结构钢循环加热淬火得到超细晶粒奥氏体,再以20℃/s的速率将其冷却至两相区进行真应变量为2的大变形,分析了形变后的瞬态组织.结果表明:用该工艺制备的超细晶奥氏体在两相区的高速大变形的后期,始终呈现应变硬化特征,并伴随有一定程度的形变诱导相变或铁素体动态再结晶等软化行为;同时,在较低温度快速大变形容易在试样的个别碳过饱和区导致应变诱导孪晶马氏体组织的生成,且随着形变温度降低孪晶马氏体量增加-循环加热淬火前的原始组织影响奥氏体内碳浓度分布,在一定程度上影响冷却变形过程的应力应变行为和形变后的瞬态组织.     

Nb47Ti合金热变形行为及微观组织

目的 研究Nb47Ti合金在变形温度为600～750℃、应变速率为0.001～1s?1条件下的热变形行为和微观组织。方法 采用Gleeble-3500型热/力模拟试验机进行等温恒应变速率压缩实验,获得Nb47Ti合金热变形的真应力应变曲线,并利用EBSD技术手段分析热变形后的微观组织。结果 Nb47Ti合金在变形温度小于650℃、应变速率小于0.1s?1下热变形的真应力-应变曲线为动态再结晶型曲线,变形温度大于等于700℃时呈现为动态回复型曲线;峰值应力随变形温度的升高和应变速率的减小而减小;在变形温度为650℃、应变速率为0.001 s?1下热变形组织以再结晶晶粒和亚晶粒为主,随着应变速率的增大,动态再结晶晶粒不断减少,而亚晶粒和变形晶粒增多,晶粒得到显著细化。当应变速率为0.1 s?1时,随着变形温度的增加,晶粒尺寸增大,变形温度升高至750℃,热变形组织中亚晶粒所占比例高达50.5%。结论 Nb47Ti合金是温度和正应变速率敏感材料,随变形温度的升高和应变速率的增大,变形过程中动态回复软化机制更为显著,低温、高应变速率下变形获得的再结晶晶粒尺寸小。     

β21S钛合金高温变形行为研究EI北大核心

在Gleeble-1500热模拟试验机上对β21S钛合金进行了高温恒应变速率压缩实验,研究其在变形温度为750～1100℃,应变速率为0．01～1s^-1条件下的流变应力及微观组织变化规律,计算了变形激活能及应力指数,并给出了流变应力的计算模型。结果表明：合金的流变应力随应变速率的增大而增大,在恒应变速率下,其应力水平随温度的升高而降低;在较低温度和高应变速率变形时,合金仅发生回复现象,随着温度的升高和应变速率的降低,有部分再结晶发生且再结晶程度逐渐增大;计算得出实验条件下的变形激活能和应力指数分别为211．04kJ／mol和4．0129。     

Ti-5Mo-5V-1Cr-3Al合金的热压缩变形行为研究EI北大核心CSCD

采用恒应变速率热压缩模拟实验,对Ti-5Mo-5V-1Cr-3A1（简称1Cr）钛合金在应变速率0.001～1s-1、变形温度700～900℃条件下进行研究.结果表明：该材料的流变应力对温度与应变速率敏感：当变形温度为700～800℃时,真应力-真应变曲线呈现动态再结晶单曲线特征;当变形温度为800～900℃时,低应变速率（0.001s-1）的真应力-真应变曲线呈现动态再结晶多应力峰值曲线特征,高应变速率（0.01～1s-1）的真应力-真应变曲线呈现动态回复曲线特征.1Cr合金在等温压缩变形时的流变行为可用包含Zener-Holomon参数的Arrhenius本构方程描述,变形激活能为456kJ/mol.金相结果显示,材料在热压缩过程中的动态行为除了与变形速率、变形温度等加工参数相关外,也与相应温度、变形速率下材料的组织及相结构有关.合金在低应变速率0.001s 1下热压缩变形时,在接近相变点或以上（800～900℃）温度范围内仍呈现动态再结晶行为,这与材料在此阶段发生的应变诱发马氏体转变密切相关,马氏体相的析出促使材料在热变形时趋向于发生动态再结晶行为.     

TC21钛合金高温热变形行为研究

研究了不同热变形条件下TC21钛合金的流变应力行为和微观组织演变规律,分析了高温热变形行为模型及动态再结晶现象.结果表明,随变形温度的升高和热变形速率的降低,TC21钛合金在热变形过程中相变和变形同时发生,导致了热变形过程中的动态回复和再结晶现象.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...