Enhanced photovoltaic performance of a dye sensitized solar cell with Cu/N Co-doped TiO<Subscript>2</Subscript> nanoparticles

Pure and Copper/Nitrogen (Cu/N)-codoped TiO₂ photoanodes with various Cu concentrations are prepared via sol–gel route for the photoanode application in dye-sensitized solar cells (DSSCs). All the prepared samples are characterized by X-Ray Diffraction (XRD), X-Ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscope (SEM), Transmission Electron Microscopy (TEM), UV–Vis spectroscopy (UV–VIS) and Electrochemical Impedance Spectroscopy (EIS). Addition of suitable amount of Cu and N content in TiO₂ can alter its optical and electrical properties by extending absorption in the visible region and band gap reduction. The results show that some of the Ti sites are replaced by Cu atoms while O sites are occupied by N atoms. Upon adequate addition of Cu/N could lead to smaller particle size, higher specific surface area, increased dye adsorption and retarded charge carrier recombination. A significant improvement in the power conversion efficiency is observed in case of optimized 0.3 mol% Cu/N-doped TiO₂ nanoparticles (NPs) based DSSC. This optimized 0.3 mol% Cu/N-doped photoanode accomplished a best power conversion efficiency of 11.70% with a short circuit current density of 23.41 mA cm^?2 which is 41% higher than that of the pure TiO₂ photoanode based DSSC (6.82%).     

Dye-sensitized solar cells using TiO<Subscript>2</Subscript> nanoparticles transformed from nanotube arrays

Dye-sensitized solar cells (DSSCs) were fabricated using TiO₂ mesoporous layers obtained by very simple method—transformation of TiO₂ nanotube (NT) films grown by electrochemical oxidation to nanoparticle (NP) films. This transformation is based on thermal annealing of TiO₂ NT arrays formed by anodization of titanium foil in fluorine ambient. Performance of DSSCs fabricated with different size NPs was studied in the range from 35 to 350 nm. Highest nominal efficiency (9.05%) was achieved for DSSC with NP size 65 nm while the lowest nominal efficiency (1.48%) was observed for DSSCs with NP size 350 nm. The dependence of the solar cell parameters with NP size is discussed.     

Optimization of TiO<Subscript>2</Subscript>/MWCNT composites for efficient dye sensitized solar cells

This paper deals with the effects of introducing multiwall carbon nanotubes (MWCNTs) into photoanodes of dye sensitized solar cells (DSSCs). Mesoporous titanium dioxide (TiO₂) nanoparticles were synthesized using sol–gel technique. TiO₂/MWCNT composites were prepared by adding functionalized MWCNTs to TiO₂ nanoparticles using two different surfactants (α-terpineol and Triton X-100). Nanoparticles and composites were characterized using Dynamic Light Scattering spectrophotometer, Raman spectrometer, X-ray diffractometer, field emission scanning electron microscope, Brunauer–Emmett–Teller surface area analyzer and UV–Vis spectrophotometer. FESEM depicted that particles were spherical in shape and their size decreased due to addition of MWCNTs. This was attributed to the decrease in the crystallite size which in turn confirmed by XRD. UV–Vis absorption spectra showed the better absorbance for the visible range of light, as the content of MWCNT is increased. From the Tauc plot optical band gap was calculated and noted that it declined gradually with the content of MWCNTs. BET surface area increased drastically which was attributed to the formation of more number of pores in the nanocomposites as visualized from FESEM. UV–Vis spectra of dye desorbed from the photoanode revealed that the dye adsorption increased as a function of MWCNT wt%. I–V studies were carried out under the illumination of 100 mW/cm² simulated sunlight. Photoanodes prepared by both the methods showed better performance compared to pristine TiO₂ photoanode, because of high conducting path and high surface area provided by MWCNTs. Photoanodes with 0.19 wt% MWCNTs in them were able to achieve maximum efficiency of 3.54 and 3.86% for method A and B respectively.     

Enhanced conversion efficiency of quasi solid state dye sensitized solar cells based on functionalized multi-walled carbon nanotubes incorporated TiO<Subscript>2</Subscript> photoanode

A series of quasi solid state dye sensitized solar cells were fabricated based on the different weight% of MWCNT@TiO₂ photoanode. The MWCNT@TiO₂ nanocomposites were synthesized by simple wet impregation method. The incorporation of MWCNT into the TiO₂ was confirmed by X-ray diffraction, energy dispersive X-ray spectrum and UV–visible spectroscopy. The morphological properties of the nanocomposites were analyzed by transmission electron microscopic analysis. The performance of the quasi solid state dye sensitized solar cell depends solely on the MWCNT content of the photoanode, as the same PVA polymer gel electrolyte has been used. Compared to the conventional TiO₂ photoanode based DSSCs 0.05 wt% MWCNT containing photoanode provide the maximum short circuit current density and the photo conversion efficiency of 9.811 mA/cm^?2 and 3.59 %. The introduction of MWCNT into the TiO₂ results in the rapid electron transport in the photoanode by forming a conductive network due to which improvement in the short circuit current was observed.     

Synthesis of cluster like TiO<Subscript>2</Subscript> mesoporous spheres and nanorods and their applications in dye-sensitized solar cells

Cluster like mesoporous TiO₂ spheres, nanorods and nanoparticles were synthesized by simple wet chemical method. The TiO₂ mesoporous spheres, nanorods and nanoparticles were characterized by powder X-ray diffraction, Raman spectroscopy, ultraviolet visible spectroscopy, Fourier transform infrared spectroscopy, field emission scanning electron microscopy and transmission electron microscopy. Accordingly, a possible growth mechanism of mesoporous spheres, nanorods and nanoparticles were discussed. The changes of the dye-sensitized solar cell (DSSC) performance with the variation of the nanostructures of TiO₂ which were used in photoanodes have been investigated. The TiO₂ mesoporous sphere based DSSC with the film thickness of 20 μm was assembled and a conversion efficiency of 6.69% was obtained.     

Construction of TiO<Subscript>2</Subscript> NP@TiO<Subscript>2</Subscript> NT double-layered structural photoanode to enhance photovoltaic performance of CdSe/CdS quantum dots sensitized solar cells

TiO₂ nanoparticles (NP) at top of TiO₂ nanotube (TiO₂ NP@TiO₂NT) double-layered architecture is constructed to combine the advantages of TiO₂ NP and TiO₂ NT together. This composite TiO₂ NP@TiO₂NT architecture as photoanode possesses a larger surface area for more QDs loading, and highly tubular structure for electron swift transport. Based on this architecture, CdSe/CdS quantum dots (QDs) have been successfully synthesized by successive ionic layer adsorption reaction (SILAR) method for quantum dots-sensitized solar cell application. The photovoltaic performance of QDSSCs based on TiO₂ NP@TiO₂ NT have been investigated in contrast with bare TiO₂ NP and bare TiO₂ NT architectures with almost the same thickness. The results show that the power conversion efficiency (PCE) of QDSSCs could be enhanced using TiO₂ NP@TiO₂ NT and improved to 3.26%, which is 80% and 38% higher than QDSSCs based on bare TiO₂ NT and bare TiO₂ NP, respectively. The BET surface area, UV–vis absorption spectra, and incident photon to current conversion efficiency (IPCE) measurements results show the evidence that the TiO₂ NP@TiO₂ NT can combine advantages of TiO₂ NP and TiO₂ NT structures together and lead to a higher light harvesting efficiency, electron collecting efficiency, and efficient electron transport.     

Construction of hierarchical TiO<Subscript>2</Subscript> nanorod array/graphene/ZnO nanocomposites for high-performance photocatalysis

The photocatalytic performance of heterostructure photocatalysts is limited in practical use due to the charge accumulation at the interface and its low efficiency in utilizing solar energy during photocatalytic process. In this work, a ternary hierarchical TiO₂ nanorod arrays/graphene/ZnO nanocomposite is prepared by using graphene sheets as bridge between TiO₂ nanorod arrays (NRAs) and ZnO nanoparticles (NPs) via a facile combination of spin-coating and chemical vapor deposition techniques. The experimental study reveals that the graphene sheets provide a barrier-free access to transport photo-excited electrons from rutile TiO₂ NRAs and ZnO NPs. In addition, there generates an interface scattering effect of visible light as the graphene sheets provide appreciable nucleation sites for ZnO NPs. This synergistic effect in the ternary nanocomposite gives rise to a largely enhanced photocurrent density and visible light-driven photocatalytic activity, which is 2.6 times higher than that of regular TiO₂ NRAs/ZnO NPs heterostructure. It is expected that this hierarchical nanocomposite will be a promising candidate for applications in environmental remediation and energy fields.     

Photovoltaic performance of TiO<Subscript>2</Subscript> using natural sensitizer extracted from <Emphasis Type="Italic">Phyllanthus Reticulatus</Emphasis>

Phyllanthus reticulatus, a natural sensitizer has been extracted from Karunelli fruit for the fabrication of TiO₂ based DSSCs. The extracted dye shows the visible light optical absorption at a wavelength of around 520 nm. The presence of anthocyanin in the dye extract has been identified by the functional molecular groups such as intermolecular –OH bond, conjugate C=O stretching vibrations using FTIR. A commercial P25 TiO₂ anatase powder has been employed for the fabrication of photoanode on fluorine doped tin oxide (FTO) substrate using Doctor-blade technique. The Platinum (Pt) counter electrode has been prepared using electron beam evaporation technique with a thickness of ~200 nm. To measure the photoconversion efficiency of the stacked DSSCs, the electrodes are assembled into a cell module and illuminated by a light source simulating AM 1.5 with a light intensity of 100 mW/cm². The freshly prepared sensitizer (P. reticulatus pH ~5.5) exhibits the photo-conversion efficiency of 0.19%, while decreasing the pH of the sensitizer (pH ~1.0) enhances the photoconversion efficiency to six times (0.69%) higher than that of fresh one.     

TiO<Subscript>2</Subscript> nanotube arrays: hydrothermal fabrication and photocatalytic activities

Titanium dioxide nanotube arrays (TiO₂ NTAs) with rutile phase have been fabricated successfully via a two-step hydrothermal method. TiO₂ nanorod arrays (TiO₂ NRAs) are first hydrothermally grown on FTO substrate. Then the TiO₂ NTAs can be obtained by controlling the HCl concentration of the hydrothermal etching process. The TiO₂ NTAs have been characterized by X-ray diffractometer, scanning electron microscope, transmission electron microscopy, X-ray photoelectron spectroscopy, and ultraviolet–visible spectroscope. Evolution of TiO₂ nanoarrays are accompanied by enhanced of the surface area and optical properties. Compared with TiO₂ NRAs, the prepared TiO₂ NTAs is more efficient in the photodegradation of methyl orange. These results reveal that the hydrothermal chemical etching provide a flexible and straightforward route for design and preparation of TiO₂ NTAs, promising for new opportunities in photocatalysts and other fields.     

Photocatalytic degradation of indigo carmine dye using TiO<Subscript>2</Subscript> impregnated activated carbon

The photocatalytic degradation of indigo carmine dye was studied using hydrothermally prepared TiO₂ impregnated activated carbon (TiO₂: AC). A comparison between the degradation of the indigo carmine dye using commercial TiO₂ and TiO₂: AC revealed the efficiency of the title compound. The degradation reaction was optimized with respect to the dye concentration and catalyst amount. The reduction in the chemical oxygen demand (COD) revealed the mineralization of dye along with colour removal. The active compound like TiO₂ was impregnated onto the activated carbon surface under mild hydrothermal conditions (<250°C, P ∼ 40 bars). The impregnated activated carbon samples were characterized using powder X-ray diffraction (XRD) and scanning electron microscope (SEM).     

The effects of electronic structure of non-metallic doped TiO<Subscript>2</Subscript> anode and co-sensitization on the performance of dye-sensitized solar cells

N/TiO₂, S/TiO₂, and N S/TiO₂ nanocrystalline films anode were obtained by doping non-metallic element N and S which could change the LUMO of anode, leading to the easy injection of electron from the excited state of dye molecule to the conduction band of semiconductor, and thus improving the photoelectric conversion efficiency and reducing the impedance of solar cells. The anode films treated by titanium tetrachloride and co-sensitized by P3HT/N719 were also studied. The absorption region of P3HT/N719 covered the entire visible region in the solar cells. The solar cell based on N/TiO₂ anode film treated by titanium tetrachloride and P3HT/N719 showed a short-circuit current density of 10.20 mA/cm², open-circuit voltage of 0.557 V, and photoelectric conversion efficiency of 2.55%.     

Enhancement of photoelectrochemical performance of CdSe sensitized seeded TiO<Subscript>2</Subscript> films

In this work, we highlight the effect of TiO₂ seed layer (SL) on the photoelectrochemical performances of CdSe/TiO₂ photoanodes (PAs). TiO₂ thin films were prepared by spin coating starting from a sol gel solution containing TiO₂ nanopowder, then sensitized with electrodeposited CdSe nanoparticles. Structural, optical and photoelectrochemical properties of the CdSe/TiO₂ PAs with and without the SL were investigated. Charge accumulation processes and charge transfer characteristics were identified by electrochemical impedance spectroscopy. The introduction of the compact TiO₂ SL was found to significantly increase the electron transport. The photocurrent density produced by the CdSe/TiO₂/SL PA reached 0.95 mA/cm², about two times higher than that performed by the CdSe/TiO₂ PAs. This enhancement might be attributed to a substantial decrease of the leakage current induced by a better crystallization of TiO₂ thin films as well as a higher sensitizing effect of the CdSe nanoparticles.     

Organic solvent based TiO<Subscript>2</Subscript> dispersion paste for dye-sensitized solar cells prepared by industrial production level procedure

In order to prepare the TiO₂ liquid dispersions for the electrodes of dye-sensitized solar cells with industrial mass production level at a reasonable cost, the present study investigates the preparation of TiO₂ liquid dispersions by a general industrial dispersion technique using readily available P25. To determine the TiO₂ dispersion offering the best light–electricity energy conversion efficiency, the suitability of various types of solvents and resins for use in TiO₂ dispersion are tested. In general, organic solvent based TiO₂ dispersions are found to allow the formation of more uniform thin films in comparison with water-based dispersions. A preparation using ethyl cellulose as the resin and the terpineol as the solvent is found to exhibit the best conversion efficiency. We have also found that using two kinds of resins of different molecular weights gave rise to better efficiency. Among 26 metal compounds tested in this study, the best metal dopant was Ag. XRD and XPS measurements confirm that the Ag exists as metal Ag and silver oxide.     

Electrical and optical properties of TiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript>:Fe thin films

TiO₂ and TiO₂:Fe thin films have been grown by electron beam evaporation and the influence of doping and heat treatment on their electrical and optical properties has been studied.     

Hierarchical Rutile TiO2 Flower Cluster‐Based High Efficiency Dye‐Sensitized Solar Cells via Direct Hydrothermal Growth on Conducting Substrates

Dye‐sensitized solar cells (DSSCs) based on hierarchical rutile TiO₂ flower clusters prepared by a facile, one‐pot hydrothermal process exhibit a high efficiency. Complex yet appealing rutile TiO₂ flower films are, for the first time, directly hydrothermally grown on a transparent conducting fluorine‐doped tin oxide (FTO) substrate. The thickness and density of as‐grown flower clusters can be readily tuned by tailoring growth parameters, such as growth time, the addition of cations of different valence and size, initial concentrations of precursor and cation, growth temperature, and acidity. Notably, the small lattice mismatch between the FTO substrate and rutile TiO₂ renders the epitaxial growth of a compact rutile TiO₂ layer on the FTO glass. Intriguingly, these TiO₂ flower clusters can then be exploited as photoanodes to produce DSSCs, yielding a power conversion efficiency of 2.94% despite their rutile nature, which is further increased to 4.07% upon the TiCl₄ treatment.     

Rutile TiO<Subscript>2</Subscript> films as electron transport layer in inverted organic solar cell

Titanium dioxide (TiO₂) thin films were prepared by sol–gel spin coating method and deposited on ITO-coated glass substrates. The effects of different heat treatment annealing temperatures on the phase composition of TiO₂ films and its effect on the optical band gap, morphological, structural as well as using these layers in P3HT:PCBM-based organic solar cell were examined. The results show the presence of rutile phases in the TiO₂ films which were heat-treated for 2 h at different temperatures (200, 300, 400, 500 and 600 °C). The optical properties of the TiO₂ films have altered by temperature with a slight decrease in the transmittance intensity in the visible region with increasing the temperature. The optical band gap values were found to be in the range of 3.28–3.59 eV for the forbidden direct electronic transition and 3.40–3.79 eV for the allowed direct transition. TiO₂ layers were used as electron transport layer in inverted organic solar cells and resulted in a power conversion efficiency of 1.59% with short circuit current density of 6.64 mA cm^?2 for TiO₂ layer heat-treated at 600 °C.     

PF127 aided preparation of super-porous TiO<Subscript>2</Subscript> film used in highly efficient quasi-solid-state dye-sensitized solar cell

The super-porous TiO₂ film is prepared with the block copolymer Pluronic F-127 as porous template. Comparing with the commonly used meso-porous TiO₂ film prepared with Polyethylene glycol 20,000 as pore former, the super-porous TiO₂ film shows higher photovoltaic performance when integrated it into polymer gel electrolyte based quasi-solid-state dye-sensitized solar cell (QS-DSSC). The enhanced dye adsorption, light scattering properties of the super-porous TiO₂ film improve the utilization efficiency of sun light to be converted to electricity. Moreover, the special microstructures of the super-porous TiO₂ film also makes for the deep penetration of polymer gel electrolyte into the dye-coated TiO₂ film, which is the prerequisite for highly photovoltaic performance of polymer gel electrolyte-based dye-sensitized solar cell. So it presents a feasible way to enhance the photovoltaic performance of QS-DSSC.     

Dye sensitized solar cell efficiency improvement using TiO<Subscript>2</Subscript>/nanodiamond nano composite

This paper aims to demonstrate the efficiency and recombination improvement of Dye-sensitized solar cells (DSSCs) by introducing of a Nanodiamond (NDs)-TiO₂ nano composite. The main challenge in the proposed application is to find the optimal wt.% of ND in TiO₂. The experimental tests were conducted to compare the developed NDs/TiO₂ cell with one of pure TiO₂ nanoparticles prepared in the same conditions. It was observed that short circuit current density, power conversion efficiency, fill factor and electron life time enhanced with increasing ND content. The best performance was obtained with 1 wt.% ND content; with a current density of 12.11 mA/cm² and light-to-electricity conversion efficiency of 4.95%. The improvement in efficiency of 18.7% was obtained as the standard DSSC was compared with that of pure TiO₂.     

Enhanced efficiency and improved photocatalytic activity of 1 : 1 composite mixture of TiO<Subscript>2</Subscript> nanoparticles and nanotubes in dye-sensitized solar cell

TiO₂-based nanotubes (NTs), nanoparticles (NPs) and composite structural film (50% NP + 50% NT film) were synthesized by sol-gel hydrothermal process. Synthetic indigo dye was used as a sensitizer with the unique combination of electrolyte (EMII + BMII + PMII) and with cobalt sulphide as counter electrode. The structure and morphology of the three films, namely, NP, NT and NPNT is studied through X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The absorption spectra and incident photon-to-current conversion efficiency (IPCE) of the three films were compared and found to be higher for NPNT film. The efficiency and photocatalytic activity of three films were evaluated. The composite structure showed improved efficiency (1.72%) than NP (1%) and NT films (0.78%). The photocatalytic activity of the three films were measured using organic dye, methylene blue under UV light radiation. The composite structure showed higher dye absorption and higher rate of reaction with time. This paper certainly proves that there are many rooms to focus on the photoanode configuration, which plays a key role to improve the efficiency of dye-sensitized solar cell (DSSC).     

Bio-inspired design of a transparent TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> composite gel coating with adjustable wettability

Although the superhydrophobicity and transparence are generally two contradictory characters as the roughness factor, it is literature abundant for achieving both of these two purposes. To our knowledge, the integration multipurpose (transparent, superhydrophobic, superhydrophilic, underwater superoleophobicity, anti-fogging, and photo-controllable ability) in one has not been reported so far and these are vital for their promising applications in various aspects which can attract broad attention from scholars to engineers. In this work, we are successful to bio-inspired design of a kind versatile transparent nanocoating with superhydrophobic or superhydrophilic/underwater superoleophobic properties. The TiO₂/SiO₂ nanocoatings can be transformed from superhydrophobicity into superhydrophilicity and underwater superoleophobicity after heat treatment (450 °C and 2 h). If it was coated on conductive glass, the electrical conductivity was impervious, while the wettability can be manipulated. Importantly, both these superhydrophobic and superhydrophilic TiO₂/SiO₂ composite nanocoatings were endowed with photo-induced self-cleaning nature and these antifouling coatings could prolong their service life.