A citrate complex process to prepare nanocrystalline PbBi2Nb2O9 at a low temperature

PbBi₂Nb₂O₉ nanocrystals with a perovskite-type structure were successfully synthesized at a relative low temperature via a citrate complex method. Metal ions were dispersed by citric acid in ethanol and ethylene glycol solvent, and then reacted with NH₄H₂[NbO(C₂O₄)₃·3H₂O] to form the gel. XRD results showed that pure PbBi₂Nb₂O₉ nanocrystals could be obtained after calcined treatment of xerogel at 800 °C. The average particles size was 57 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the sintering process led to the agglomeration of the nanoparticles. The photocatalytic test showed that the sample prepared by the citrate complex method exhibited a higher photocatalytic activity than that of the sample prepared by the solid-state reaction.     

Preparation and visible-light photocatalytic activity of In2S3/TiO2 composite

A novel In₂S₃/TiO₂ composite with visible-light photocatalytic activity was prepared by a chemical precipitation method and characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope and UV–vis diffuse reflectance spectroscopy. Under both UV- and visible-light irradiation, the In₂S₃/TiO₂ composite shows good photocatalytic activity to degrade methyl orange, ascribed to the absorption of visible light by In₂S₃ sensitizer and enhanced separation of photoinduced electron–hole pairs in the composite semiconductors.     

Photocatalytic degradation of RhB over MgFe2O4/TiO2 composite materials

MgFe₂O₄/TiO₂ (MFO/TiO₂) composite photocatalysts were successfully synthesized using a mixing-annealing method. The synthesized composites exhibited significantly higher photocatalytic activity than a naked semiconductor in the photodegradation of Rhodamine B. Under UV and visible light irradiation, the optimal percentages of doped MgFe₂O₄ (MFO) were 2 wt.% and 3 wt.%, respectively. The effects of calcination temperature on photocatalytic activity were also investigated. The origin of the high level of activity was discussed based on the results of X-ray diffraction, UV-vis diffuse reflection spectroscopy, scanning electron microscopy, transmission electron microscopy, and nitrogen physical adsorption. The enhanced activity of the catalysts was mainly attributed to the synergetic effect between the two semiconductors, the band potential of which matched suitably.     

The enhanced visible light photocatalytic activity of nanosheet-like Bi2WO6 obtained by acid treatment for the degradation of rhodamine B

Bi₂WO₆ samples were fabricated by chemical solution decomposition (CSD) method and nanosheet-like Bi₂WO₆ samples could be obtained by concentrated nitric acid treatment at 70 °C for 20 min. The products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and UV-vis diffuse reflectance spectra. Photocatalytic activities of the samples were evaluated by the degradation of rhodamine B (RhB) under visible light irradiation. The temperature of acid treatment obviously influenced morphology and the visible light photocatalytic activity of the Bi₂WO₆ samples. The nanosheet-like Bi₂WO₆ photocatalysts obtained by acid treatment exhibited the highest photocatalytic activity under visible light irradiation.     

等离子体电解氧化法制备多孔TiO2/V2O5复合物膜层及其增强光催化产氢活性

较差的光催化产氢效率极大地阻碍了TiO₂光催化剂的工业化应用。为此,本文在含有NH₄VO₃的磷酸盐溶液中,采用等离子体电解氧化(PEO)法制备了多孔TiO₂/V₂O₅复合膜光催化剂,通过扫描电子显微镜(SEM)、能谱仪(EDS)、X射线衍射(XRD)、X射线光电子谱(XPS)和紫外可见漫反射光谱(UV-Vis DRS)对其组成、结构及光吸收性质进行了表征,并采用气相色谱评价了薄膜催化剂的光催化产氢性能,研究了电解液中NH₄VO₃含量对膜的结构、组成和光催化产氢性能的影响。结果表明:复合膜催化剂主要由锐钛矿和金红石型TiO₂组成,具有微孔结构,V₂O₅主要以无定形形式存在于膜中,与TiO₂有很强的相互作用,影响TiO₂的晶面间距。研究发现,元素V抑制了TiO₂的结晶和金红石型TiO₂的形成,扩大了薄膜的光学吸收范围。针对Na₂S+ Na₂SO₃溶液中的光催化产氢性能的研究显示,在质量浓度为1 g/L NH₄VO₃的电解液中制备的TiO₂/V₂O₅薄膜的光催化活性最高,优于近年来报道的其他光催化剂。光催化重复实验表明,该复合膜催化剂具有较高的稳定性和较为恒定的光催化活性。     

Synthesis of nanostructured M/Fe3O4 (M = Ag,Cu) composites using hexamethylentetramine and their electrocatalytic properties

Nanoscaled Ag/Fe₃O₄ hybrids with different Ag contents and Cu/Fe₃O₄ nanoshpere and microsphere were successfully synthesized with assistance of sodium citrate and (CH₂)₆N₄ via a hydrothermal process. The as-prepared samples were identified and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS), respectively. All samples were used as electrocatalysts modified on a glassy carbon electrode for p-nitrophenol reduction in a basic solution. The catalytic activity of Ag/Fe₃O₄ samples increased first and then decreased by increasing Ag content from 0% to 8%, and the one with 6% Ag displayed the highest catalytic activity. All the Cu/Fe₃O₄ samples exhibited enhanced catalytic activity by comparison with a glassy carbon electrode, and the one prepared with the molar ratio of Cu²⁺, Fe³⁺, citrate anion, and (CH₂)₆N₄ with 1:1:3:5 exhibited the highest catalytic activity.     

Preparation of nitrogen co-doped SiO2/TiO2 thin films on ceramic with enhanced photocatalytic activity under visible-light irradiation

In this study, we have successfully deposited N-doped SiO₂/TiO₂ thin films on ceramic tile substrates by sol–gel method for auto cleaning purpose. After dip coating and annealing process the film was transparent, smooth and had a strong adhesion on the ceramic tile surface. The synthesised catalysts were then characterised by using several analytical techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscope (AFM) and UV-vis absorption spectroscopy (UV-vis). The analytical results revealed that the optical response of the synthesised N-doped SiO₂/TiO₂ thin films was shifted from the ultraviolet to the visible light region. The nitrogen substituted some of the lattice oxygen atoms. The surface area of co-doped catalyst increased, and its photocatalytic efficiency was enhanced. The photocatalytic tests indicated that nitrogen co-doped SiO₂/TiO₂ thin films demonstrated higher than of the SiO₂/TiO₂ activity in decolouring of methylene blue under visible light. The enhanced photocatalytic activity was attributed to an increasing of the surface area and a forming of more hydroxyl groups in the doped catalyst.     

Template-free hydrothermal synthesis and high photocatalytic activity of ZnWO4 nanorods

ZnWO₄ nanorods are successfully synthesized by a template-free hydrothermal method, and are characterized in detail by X-ray diffractometer (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED). The results show that the ZnWO₄ nanorods with wolframite structure are well-crystallized single crystallites. The crystallinity of the products is influenced by the pH value of initial precursor suspension. The width and length of the synthesized samples increase with hydrothermal reaction temperature. The photocatalytic efficiency of the ZnWO₄ nanorods for degradation of methylene blue (MB) in aqueous solution under UV light irradiation declines greatly with increasing crystallinity. The ZnWO₄ nanorods prepared at pH of 4 have the best activity in photo-degradation of MB. After six recycles, photocatalytic activity loss of the catalyst is not obvious.     

水热合成的MoS2/石墨烯/N-TiO2复合材料的可见光催化性能

以氧化石墨烯(GO)、钼酸、硫脲和TiN为原料,成功制备了MoS_2/石墨烯/N-TiO_2(MGNT)复合材料。利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HR-TEM)、X射线光电子能谱(XPS)及紫外-可见漫反射光谱(UV-Vis DRS)等手段测试分析了样品的物相组成、形貌、成分和光吸收性能。紫外-可见漫反射测试结果表明,MoS_2、石墨烯共同修饰及氮掺杂使得TiO_2的吸收带边发生红移,且其可见光吸收性能明显提高。可见光照射下降解亚甲基蓝溶液的实验结果表明,MoS_2/石墨烯共同修饰的氮掺杂TiO_2的光催化降解性能分别是氮掺杂TiO_2(NT)和石墨烯修饰氮掺杂TiO_2(GNT)的1.82倍和1.59倍,其吸附性分别为氮掺杂TiO_2、石墨烯修饰氮掺杂TiO_2的11.14倍和4.77倍。     

Photocatalytic effects for the TiO2-coated phosphor materials

This study investigated the photocatalytic behavior of the coupling of TiO₂ with phosphorescent materials. A TiO₂ thin film was deposited on CaAl₂O₄:Eu²⁺,Nd³⁺ phosphor particles by using atomic layer deposition (ALD), and its photocatalytic reaction was investigated by the photobleaching of an aqueous solution of methylene-blue (MB) under visible light irradiation. To clarify the mechanism of the TiO₂-phosphorescent materials, two different samples of TiO₂-coated phosphor and TiO₂–Al₂O₃-coated phosphor particles were prepared. The photocatalytic mechanisms of the ALD TiO₂-coated phosphor powders were different from those of the pure TiO₂ and TiO₂–Al₂O₃-coated phosphor. The absorbance in a solution of the ALD TiO₂-coated phosphor decreased much faster than that of pure TiO₂ under visible irradiation. In addition, the ALD TiO₂-coated phosphor showed moderately higher photocatalytic degradation of MB solution than the TiO₂–Al₂O₃-coated phosphor did. The TiO₂-coated phosphorescent materials were characterized by transmission electron microscopy (TEM), Auger electron spectroscopy (AES) and X-ray photon spectroscopy (XPS).     

Fabrication and photocatalytic property of ZnO nanorod arrays on Cu2O thin film

ZnO nanorod arrays were fabricated on Cu₂O thin film by a simple low-temperature liquid-phase-deposition method. The samples were characterized by X-ray powder diffraction (XRD) and field emission scanning electron microscopy (FESEM). The UV-Vis spectroscopy showed that the obtained sample was able to absorb a large part of visible light (up to 650 nm). Their photocatalytic activities were investigated by degradation of dye methylene blue (MB) under UV-Vis and visible light irradiation. It was found that the photocatalytic activity of the ZnO/Cu₂O NRs was higher than the ZnO/ZnO NRs under UV-Vis light. In a word, Cu₂O played an important role in enhancing the photocatalytic activity of the ZnO/Cu₂O NRs.     

Mesoporous Au/TiO2 composites preparation,characterization, and photocatalytic properties

In this work, mesoporous Au/TiO₂ composites have been synthesized and tested on photodegradation of methylene blue dye solution. Mesoporous TiO₂ prepared at 450 °C using triblock polymer F127 as structure-directing agent was applied as substrate, while various HAuCl₄ concentrations were used for Au loading through deposition-precipitation method using urea as precipitator and hydrogen reducing process. The influences of Au loading on the microstructures of mesoporous TiO₂ including degree of dispersion, particle size, surface area, light absorption, and band gap were studied with transmission electron microscopy (TEM), X-ray diffraction (XRD), diffuse reflection infrared Fourier transformed spectroscopy (DRIFT), N₂ adsorption–desorption isotherm analysis (BET), and UV–Vis diffuse reflectance spectra. With Au loading, the size of TiO₂ nanoparticles in Au/TiO₂ composites is similar as that of TiO₂ substrate. However, the degree of dispersion was greatly improved. Furthermore, an obvious surface plasmon resonance centered at 570 nm was found in UV–Vis diffuse reflectance spectra for Au/TiO₂ composites. Au loading also induced an obvious red shift of light absorption from UV region to visible region and strengthened both UV and visible light absorption in contrast to substrate. Photodegradation results verified that photocatalytic activity of mesoporous TiO₂ was improved by Au loading. 0.25%Au/TiO₂ composite showed the highest activity, which may be ascribed to its high surface hydroxyl content and the formed Schottky junction after Au loading. These results suggested that noble metal modification is a promising way to synthesize photocatalysts with both high activity and visible light sensitivity.     

Catalytic reduction of CO2 to alcohol with Cu2Se-combined graphene binary nanocomposites

Photocatalytic reduction of CO₂ over a Cu₂Se–graphene nanocatalyst has been investigated. The nanocomposite material was successfully prepared via a modified hydrothermal method. The structure and properties of the prepared composite were characterized by X-ray diffraction, scanning electron microscopy with energy dispersive X-ray microscopy, transmission electron microscopy, Raman spectroscopic analysis, and X-ray photoelectron spectroscopy. A synergetic effect of the combination of Cu₂Se and graphene appeared in the form of excellent photocatalytic reduction capability of CO₂. The photocatalytic efficiencies of the samples were characterized by testing for the photoreduction of CO₂ to alcohol under visible light irradiation, which produced results such as to suggest that there is a significant potential for graphene-based semiconductor hybrid materials to be used as photocatalysts for reduction of CO₂.     

Photocatalytic degradation of pendimethalin over Cu2O/SnO2/graphene and SnO2/graphene nanocomposite photocatalysts under visible light irradiation

The Cu₂O/SnO₂/graphene (CSG) and SnO₂/graphene (SG) nanocomposite photocatalysts were prepared by simple sol-gel growth method, and characterized by Fourier transform infrared spectra (FTIR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer–Emmett–Teller (BET) measurements, respectively. The photocatalytic efficiency of catalysts were evaluated by degradation of pendimethalin under visible light irradiation (λ > 420 nm), which conformed that CSG and SG exhibited better photocatalytic activity than SnO₂ or graphene alone. An effort has been made to correlate the photoelectro-chemical behavior of these samples to the rate of photocatalytic degradation of pendimethalin.     

Synthesis and characterization of N-doped TiO2/ZrO2 visible light photocatalysts

Zirconia and nitrogen-doped TiO₂ powder was synthesized using a polymer complex solution method for the preparation of an enhanced visible light photocatalyst. The produced catalysts were characterized via the Brunauer, Emmett, and Teller method (BET), X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectra, and UV–Vis spectrophotometry analyses. The N-doped TiO₂/ZrO₂ photocatalyst showed a high specific surface area and small crystal sizes. The XPS spectra of the N-doped TiO₂/ZrO₂ sample indicated that nitrogen was doped into the TiO₂ lattice and enhanced the photocatalytic activity. The UV–Vis absorption spectra of the N-doped TiO₂/ZrO₂ sample noticeably shifted to the visible light region compared to that of the TiO₂. The photocatalytic activities of the prepared catalysts were evaluated for the decomposition of gaseous NO_x under UV and visible light irradiations. The photocatalytic activities of N-doped TiO₂/ZrO₂ were much greater than those of commercial Degussa P25 in both the UV and visible light regions. The high photocatalytic activity can be attributed to stronger absorption in the visible light region, a greater specific surface area, smaller crystal sizes, more surface OH groups, and to the effect of N-doping, which resulted in a lower band gap energy.     

Preparation of monoclinic BiVO4 thin film by citrate route for photocatalytic application under visible light

A monoclinic BiVO₄ (mBiVO₄) film composed of nanoparticles with a size of 100 nm was prepared via a citrate-precursor chemical route. The BiVO₄ film was characterized by X-ray diffraction, scanning electron microscopy and absorption spectra. It was found that the mBiVO₄ film showed a photocatalytic activity of Acid Orange 7 (AO7) degradation in aqueous solution under visible-light irradiation (λ > 400 nm). The degradation efficiency was 78.9% in 3 h and basically remained constant in 10 repeated batch runs. The results demonstrated that the mBiVO₄ film had a high photocatalytic activity under visible light and good durability in repeated use.     

Preparation of metal ion (Fe and Ni) doped TiO2 nanoparticles supported on ZSM-5 zeolite and investigation of its photocatalytic activity

Metal ion doped TiO₂ nanoparticles supported on ZSM-5 zeolite (M-TiO₂/ZSM-5 composites, M = Fe or Ni) were synthesized by hydrothermal method. The prepared composites were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV–vis diffuse reflectance spectra (DRS). The photocatalytic activities of composites were evaluated by degradation of yellow GX aqueous solution under ambient condition. Fe-TiO₂/ZSM-5 composite showed to be more efficient catalyst for degradation of dye molecules as compared with Ni-TiO₂/ZSM-5 and TiO₂/ZSM-5. Its higher photocatalytic activity is attributed to the effective separation of charge carriers that will be discussed in this paper in detail.     

Controlled hydrothermal synthesis of VO2(B) nanobelts

Large-scale VO₂(B) nanobelts have been synthesized by hydrothermal strategy via one-step method using V₂O₅ as vanadium source and C₆H₅-(CH₂)_n-NH₂ with n = 2 and 4 (2-phenylethylamine and 4-phenylbutylamine) as structure-directing templates. The composition and morphology of the nanobelts were established by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FTIR). The as-obtained VO₂(B) nanobelts have a length of 3-10 μm, a wideness of 100-375 nm and a thickness of 30-66 nm.     

Visible light absorption ability and photocatalytic oxidation activity of various interstitial N-doped TiO2 prepared from different nitrogen dopants

Nitrogen-doped TiO₂ was developed to enable photocatalytic reactions using the visible range of the solar spectrum. This work reports on the synthesis, characterisation and kinetic study of interstitial N-doped TiO₂ prepared by the sol–gel method using three different types of nitrogen dopants: diethanolamine, triethylamine and urea. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV–visible spectroscopy were used to analyse the titania. Different interstitial N-doped TiO₂ properties, such as absorption ability in the UV–visible light region, redshift in adsorption edge, good crystallisation and composition ratio of titania structures (anatase and rutile) could be obtained from different nitrogen dopants. Amongst investigated nitrogen precursors, diethanolamine provided the highest visible light absorption ability of interstitial N-doped TiO₂ with the smallest energy bandgap and the smallest anatase crystal size, resulting in the highest efficiency in 2-chlorophenol degradation. The photocatalytic activity of all N-doped TiO₂ can be arranged in the following order: TiO₂/diethanolamine > TiO₂/triethylamine > TiO₂/urea > un-doped TiO₂. The initial rate of 2-chlorophenol degradation using the interstitial N-doped TiO₂ with diethanolamine was 0.59 mg/L-min and the kinetic constant was 2.34 × 10⁻² min⁻¹ with a half-life of 98 min. In all cases, hydroquinone was detected as a major intermediate in the degradation of 2-chlorophenol.     

β- and α-Bi2O3 nanoparticles synthesized via microwave-assisted method and their photocatalytic activity towards the degradation of rhodamine B

Amorphous β-Bi₂O₃ nanoparticles were synthesized directly via a liquid phase microwave reaction, and changed gradually into well crystallized sheet-like nanoparticles of β-Bi₂O₃ or α-Bi₂O₃ during the following calcining at lower (300 °C) or higher (350 °C) temperature. Powder X-ray diffraction (XRD), transmission electron microscopy (TEM) and diffuse reflectance spectroscopy (DRS) were used to characterize the samples. The photocatalytic activity of the samples under simulated sunlight was also investigated by taking the degradation of rhodamine B (RB) as model reaction. β-Bi₂O₃ showed lower band gap energy and high absorbance in wider visible light region than α-Bi₂O₃ did, resulting in its higher photocatalytic activity. It was also found that higher crystallinity can improve the activity.